Tag Archives: sanding a stem

A Stanwell Danish Star 64

Blog by Steve Laug

My brother sent me a nice looking Stanwell shape 64 with a nice plateau top. The briar itself was in good shape. There were no dents of nicks in the briar. The finish was in great shape. The rim was decent but the plateau was clean and in decent shape. The high spots were the same brown as the bowl and the nooks and crannies were dark brown or black. It was stamped on the left side of the stem with the words Stanwell over Danish Star. On the right side it was stamped with the shape number 64. On the underside of the shank it is stamped Made in Denmark. The stem was lightly oxidized and there were tooth marks on the top and underside near the button. The bite marks on the underside were deep but the ones on the topside was a bite through into the airway. I took a close up photo of the top of the bowl. It shows the grooves, crevices and the high spots on the plateau top. It was dirty and there was dust in the grooves of the rim.I took close up photos of the stem to show the condition of the top and bottom side of the stem. The photo of the top shows the bite through and the tooth marks that were further down the stem top. The photo of the underside shows the tooth marks there as well. The tooth marks were deep and large. There were also bite marks on the top and the bottom of the button.I sanded the surfaces of the stem and cleaned out the dents in the surface with alcohol and cotton swabs. I greased a pipe cleaner with Vaseline and inserted it into the airway of the stem. I mixed a putty of charcoal powder and black super glue with a piece of straightened paper clips. I filled in the bite through with putty and the paper clip until it was thickly covered. I filled in the dents in the surface of the stem and built up the worn spots on the button edge. I sprayed the repairs with the accelerator to harden the repair. When the glue had hardened and cured I used a file to smooth out the repaired spots on both sides of the stem.I sanded the repaired areas with 220 grit sandpaper to smooth out the surface and remove the scratches left by the file. It took some time but I was able to sand out the scratches.I filled in some of the air holes in the repair with clear super glue and sanded the surface with 220 grit sandpaper to smooth out the stem.I polished the stem with micromesh sanding pads – I wet sanded it with 1500-2400 grit sanding pads and dry sanded it with 3200-12000 grit pads. I rubbed the stem down with Obsidian Oil after each set of three pads. I gave it a final coat of Obsidian Oil and set aside to dry. The plateau top was in great shape. I used a black Sharpie pen to highlight the grooves and crevices in the rim top. I buffed the pipe and stem with Blue Diamond on the buffing wheel to raise a shine and remove the last of the scratches on the vulcanite. I buffed the bowl surface to polish out the light scratches in the briar. The Blue Diamond gave the finish on both the bowl and the stem a high shine. I gave the pipe multiple coats of carnauba wax and buffed it with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. The colour of the stain on the pipe really makes the grain stand out clearly on the pipe. Thanks for having a look.

Restemming a Savinelli Capri Root Briar 320 and giving it a new look

4 Replies

Blog by Steve Laug

I have always liked the looks of the Savinelli 320 shape. I have one of them here and it is a 320EX so it is quite large. When my brother Jeff sent me photos of one that he was looking at I was interested. He bid on it and won. It is stamped on the underside of the shank on a smooth spot with the words Savinelli Capri over Root Briar. Next to the stamping was the Savinelli shield and to the right of that it reads 320 over Italy. The finish on the bowl looked really good. I really like the Capri rustication and the roughness of the feel in the hand.My brother sent me the photos above as well as these close up photos. The rim was actually in very good shape, surprisingly. The there was a thick rough ca,e in the bowl and some of the lava had overflowed on to the rim top grooves.The underside of the shank was in excellent shape though there were some scratches on the smooth area. The pebble cut rustication was in excellent condition. The contrast stain on the pebble finish other than being dirty was undamaged.The real issue with the pipe lay with the stem. The stem had been gnawed to the point that there was almost an inch or more of the stem missing. It was missing a large portion of the vulcanite on the top and the underside of the stem. It is ironic that the stem logo was the only thing about the stem that was left undamaged. My brother is getting really good at his cleanup process and this pipe was no exception. I am getting spoiled when I get a pipe that I have to ream and clean. When he sends them they have been reamed, scrubbed with Murphy’s Oil Soap on the exterior and cleaned thoroughly with alcohol, cotton swabs and pipe cleaners on the inside. I took some photos of the pipe to show the condition it was in when it arrived in Vancouver. You can see that the finish is clean and you can see the horrible damage to the stem. I took a close up photo of the rim and the bowl. He had reamed back the cake to bare briar and also scrubbed the rustication on the rim and removed all of the tars and oils that had filled in portions of it on the back side of the bowl.The original stem was a lost cause at this point. To shorten and reshape a new button I would have had to cut off almost another ½ inch. To my mind that would have made the pipe too short for my liking. I went through my can of stems and found a stem that had potential. The diameter of the stem at the tenon end was slightly larger than the Savinelli stem but it had room for adjustments. It had some file marks on the top and the tenon was a little large in diameter for the shank of the 320 but with a little work it would work. It had some paint on the top of the saddle and was deeply oxidized. There was not any tooth chatter or tooth marks on it. It would certainly work for the 320 but it would change the appearance. Once I had finished the fit I would take some pictures and make a decision.I scraped out the mortise with a dental spatula to remove the hard tarry build up that had accumulated there. Once I had scraped it clean I scoured out the inside of mortise and airways in the shank and the stem with alcohol, pipe cleaners and cotton swabs.I sanded the tenon with a Dremel and a sanding drum to fine tune the fit in the shank. I also adjusted the diameter of the saddle with the Dremel and sanding drum until it was a close fit to the diameter of the shank. I fine-tuned the fit with 220 grit sandpaper until the saddle portion was free of the sanding marks left behind by the Dremel. I sanded the tenon with 220 grit sandpaper to adjust the fit in the mortise. I finished by sanding the remainder of the stem as well to break up the oxidation.Once the fit in the mortise and to the shank was correct I pushed the stem in place and took photos of the new look of the pipe. Part of this was to mark the progress but it was also an opportunity for me to see it from the eye of the camera and assess whether I would keep working on the stem or just wait until I came across another Savinelli tapered stem. As I studied the photos I was pleased with the look. There was something catching about the new slim stem flowing from the saddle. I liked the looks of it. I sanded the stem with the 220 grit sandpaper until I had removed the oxidation and then rubbed the bowl down with a light coat of olive oil to rejuvenate the briar. I rubbed the stem down with Obsidian Oil and took the next set of pictures. The pipe was beginning to look really good. I polished the stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I rubbed the stem down with Obsidian Oil after each set of three pads. I gave the stem a final coat of Obsidian Oil after the last micromesh pad and set it aside to dry. I buffed the stem with Blue Diamond polish on the buffing wheel to polish it further. I gave the stem multiple coats of carnauba wax and gave the bowl several coats of Conservator’s Wax. I buffed the bowl and stem with a clean buffing pad to raise the shine. I finished the pipe by buffing it by hand with a microfibre cloth. The finished pipe is shown in the photos below. It took some work to fit the new stem to the shank but the new look of the saddle stem gives this pipe a fresh appearance to me that works well with the pebble rustication of the Capri Root Briar finish.

An interesting “The Nuvo” MLC Italian Briar hidden in a WDC Case

6 Replies

Blog by Steve Laug

When we saw this older case and pipe for sale on eBay we were under the assumption that the pipe in the case was an older WDC pipe. The age of the case and the pipe appeared to match in the photos posted by the eBay seller. The case was in decent shape on the left side and the right side had a ripped part missing near the stem end. The covering on the case was leather. The hinge and clasp mechanism were in good condition. The green velvet lining looked worn. The stamp on the inside the top of the case was readable but worn. It read WDC in the triangle and over Genuine Briar. The finish on the briar was worn looking and the stem looked like it was covered with white calcification over the length of the stem all the way around. The bowl was thickly caked with a thick coat of lava overflowing onto the rim. It was so thick that it was hard to tell if the outer and the inner edges of the rim were in good condition. Underneath it may well have a lot of nicks and the bowl could easily be out of round.The seller included some close up photos of the stamp on the inside cover of the case. You can see the WDC triangle logo over Genuine Briar. They also included close up photos of the stamping on the left and right sides of the shank. It is very hard to read the lettering in the photos. It looks like the left side is stamped with something over Special Pat. On the right side what is readable is Italian Briar. The rest of the stamping was not readable in the photos.

When the pipe arrived in Idaho my brother took photos of the pipe before he cleaned it up. The finish was certainly a mess and there was a lot of grime and build up on the bowl and the shank. There also appeared to be some nice grain peering through the grime.He took some close up photos of the rim and the front of the pipe. The overflow of lava and the cake in the bowl was very thick. The outer edge of the rim was rounded and showed some damage. The frontal photo shows a dent at the front top of the bowl that goes diagonally across the bowl. I have circled it in red to show the location of the dent.He also took photos of the stamping for me. On the right side of the shank there appeared to be an oval with the letters stamped MLC in the centre. On the left side it seems to read “The Nuvo” over Special Pat.The closes up photos of the white substance on the stem surface show the condition of the stem and looks almost crystalline.I took some photos of the pipe when it arrived in Vancouver and I brought it to the work table to begin the restoration. My brother had done an amazing job cleaning up the dirty finish and the white on the stem. He had reamed the bowl clean of the thick cake. He also removed the thick lava on the rim top. I took a close up photo of the bowl and rim to show the condition. My brother had been able to remove all of the cake and the tar. The outer edge of the rim was rounded and had dents. The inner edge was missing chunks and the bowl was out of round. The top of the rim had nicks and dents and was also in rough shape.The stem looked to be in decent condition. The high quality rubber of the stem was pitted and lightly oxidized. The style of the button added to my idea that I was dealing with an older pipe.I was able to clearly read the stamping on the pipe once I had it in hand. It read “The Nuvo” over Special Pat. on the left side of the shank. On the right side it was stamped with an MLC in an oval over Italian Briar. I was not familiar with th name on the pipe or the Oval MLC stamp. I looked my copy of “Who Made that Pipe” and found that The Nuvo was made by M. Linkman Company in 1914. The MLC logo in the oval stood for M. Linkman Company.

I looked the brand up on Pipedia (https://pipedia.org/wiki/M._Linkman_%26_Co) and found that M. Linkman Company name was said to stand for Mary Linkman & Company. Mary Linkman was the mother of Louis B. Linkman, originator of the Dr. Grabow pipe. This Chicago company produced both meerschaums and briars. I also looked on the PipePhil Logos and Stampings site (http://www.pipephil.eu/logos/en/logo-l4.html) and found that the M. Linkman and Co. was established by Louis B. Linkman and August Fisher in 1898. The company closed down in the 1950s and the Dr Grabow branch was sold to Henry Leonard and Thomas Inc. There was also a note that early Linkman’s pipes were stamped MLC in an oval.

I now knew that the pipe I had in hand was an early Linkman’s pipe rather than one made by WDC. That meant that the case and the pipe did not match.

I decided to try to clean up the inside edge of the bowl before I topped it. I wanted to remove as much of the damage to the inner rim as I could to better see how much of the rim top I would need to remove with the topping action. I used a rolled piece of 220 grit sandpaper wrapped around my finger to sand the inner edge of the bowl.When I finished sanding the edge there were still some deep gouges in the edge of the rim at the back and the front of the bowl. The bowl was also out of round and seemed to be thinner on the right side than the rest of the bowl.I topped the bowl rim on a topping board with 220 grit sandpaper. I worked on it until I had removed all of the damage to the rim top and also removed the damage to the outer edge of the rim and also what was on the inner edge. In the second photo you can see that much of the damage to the inner edge of the rim was removed. I still needed to bevel that edge to smooth out the damage.I used a folded piece of 220 grit sandpaper to sand the edge of the bowl. I worked it over until I had removed the damaged areas on the front and the back side of the rim edge. I also worked to make the bowl round once again.I sanded the rim edges and the top of the rim with 1500-4000 grit micromesh sanding pads once i had the bowl in round. I scraped the inside of the mortise with a dental pick to remove the hard chunks of tar that were collected on the inside walls of shank. Once I had removed all of the hardened buildup I scrubbed out the mortise and the airways in the shank and the stem with pipe cleaners, cotton swabs and alcohol until the oils and tars were gone.I wiped down the exterior of the briar with acetone on a cotton pad to remove all of the residual dirt and grime from the topping and cleaning. I wanted the surface to be clean and oil free in preparation for the new stain coat that I would give it. I thinned some dark brown aniline stain by 50% with isopropyl alcohol (need to put in an order for more stain). I applied it to the bowl with a folded pipe cleaner. I flamed the stain to set it and repeated the process until the coverage on the bowl and shank were an even medium brown colour. I set the bowl aside to let the stain cure and turned my attention to working on the stem. I sanded it with 220 grit sandpaper to remove the light oxidation and smooth out the pitted surface of the stem. I polished it with micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding it with 3200-12000 grit pads. I rubbed the stem down with Obsidian Oil after each set of three sanding pads. I gave it a final coat of oil after the third set of pads and set it aside to dry. I put the stem back on the pipe and buffed it with Blue Diamond on the buffing wheel. I took precaution to not buff the stamping on the shank sides. I gave the bowl and stem multiple coats of carnauba wax to protect it. I buffed it with a clean buffing pad to raise a shine. I hand buffed it with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. I am happy with the way it turned out. The look and finish of the pipe turned out very well. Thanks for walking with me through the process.

Restoring the fourth Classic Find – a Jost’s Supreme Diamond Shank bent billiard

4 Replies

Blog by Steve Laug

I written about the estate lot that my brother and I purchased from an estate sale in Pocatello, Idaho. There were a lot of great pipes in the lot. I have written about the pipes we picked up in a previous blog: (https://rebornpipes.com/2016/10/07/a-good-day-hunting-orchestrated-between-british-columbia-and-idaho/). I also wrote of how my brother had stopped at an antique shop and found four amazing pipes. These included a Four Dot Sasieni Pembroke with a patent number, Pat.No. 150221/20, a Dunhill Root Briar Canadian EC 4R, a Charatan’s Make Canadian Sandblast 0121 and finally a Jost’s Supreme Diamond Shank bent billiard. I have restored and written blogs on three of the four pipes he found – Sasieni, Dunhill and the Charatan’s Make. Here are those links: (https://rebornpipes.com/2016/11/05/restoring-a-classic-find-a-sasieni-four-dot-london-made-pembroke/ ; https://rebornpipes.com/2016/11/06/restoring-another-classic-find-a-dunhill-4r-root-briar-canadian-ec/ ; and https://rebornpipes.com/2016/11/06/restoring-the-third-classic-find-a-charatans-make-0120-canadian/. I am now finished with the fourth pipe that – the Jost’s Supreme diamond shank bent billiard.

In earlier blogs I have written about restoring another Jost’s pipe that I found. When I restored that pipe it was a brand I had heard of but was unfamiliar with. I researched the web to find some information about the brand. Here is a link to the blog I wrote on the Jost’s Olde English Deluxe: https://rebornpipes.com/2016/09/03/josts-olde-english-de-luxesupreme-overstamped-j214-bent-billiard/. I am quoting several of the paragraphs that summarize what I learned about the brand.

“I looked up Jost’s pipes on the pipephil site and found a pipe that had the same stamping on the left side of the shank as the one I was working on. The right side had slightly different stamping in that it had the classic COM stamp circle where the one I had was two lines Made in over England. It also had a picture of the circle J stamp on the stem. There was a note there the tobacco shop proprietor was Mrs. Henry A. Jost. Her resident carver was Harvey Raspberry.”

I also found a blog that is called ClassicPipeShop that even had a catalogue of the pipes made by the Jost’s Shop or were imported by them for their store. I quote that blog once more as it places the new pipe that I am working on now.

“I did some more hunting online and I found a blog that did a great write up on Jost’s Pipe Shop and gave some definitive information on the brand and grades of the pipes. Here is the link if you wish to read a well written history of the brand and also some interesting details about shop blends of tobacco. http://classicpipeshop.blogspot.ca/2015/03/josts-pipe-shop-201-north-6th-street-st.html”

“I have included the section of the blog on the pipes. It covers a lot of information regarding the source of the pipes and the levels/grades of pipes. Remember that the one I am working on is a De Luxe/Supreme. I quote:”

“Jost’s Pipes are closely tied to Comoy’s. Many of Jost’s pipes have the standard Comoy’s shape number and the “Made in England” in a circle. If the Jost’s pipe doesn’t have the “Made in England” it is probably made by Harvey Raspberry.”

“If the pipe has a shape number that is preceded by a “J” that is a Comoy’s product without question. Typically these will have the words “Made in London England” on the reverse side of the shank from where the Jost stamp is made. There are always exceptions to the rule but 95% of the time, this is accurate.”

“Many different levels of pipes were offered by Jost’s Pipe Shop. From a 1950s catalog I have the following available:”

Jost Old English De Luxe: $85.00

These were typically of the highest… Grain is stunning and the briar is flawless. These are the grade you should look out for as they are great smokers.

*Jost Old English Supreme: (no pricing available)

The majority of the Old English version pipes you see are marked Supreme. These are stained in a darker color and are presumably from the same Algerian aged Briar as the De Luxe brothers. These are also of the highest quality available. *(The current pipe I am working on is stamped Jost’s Supreme on the left side of the shank with no shape number and no Made in London England stamp. If I read the information correctly it was one that was made by Harvey Raspberry, who was the shop pipe maker.)

Jost Virgin Briar Supreme: $35.00

Don’t see too many marked as Virgin Briar Supreme but you will often find “Supreme” Jost pipes on the second hand market (see above). Excellent quality briar and displays the lighter toned finish of the De Luxe above. Grain is not as flashy or desirable as the De Luxe model.

Jost Thames Briars: $25.00

I’ve seen these offered as blasted / rusticated pipes and look quite nice. Most of the smooth finish Thames pipes are riddled with fills. Good smokers but not much to look at (smooth).

Jost Sandblast Briars: $25.00

These are a great value. The shop made sand-blasted pipes are usually quite large and snapped up very quickly by collectors. The Comoy’s versions (with J shape #s) are of excellent quality and typically rather small compared to the shop-made variety.

Dukes Briars: $15.00

These come up very rarely. The two I’ve seen in recent years are rather small in size. Smooth finish with light / honey stain color. Not sure what the story is behind these.

From my research and rereading of the information on the brand it appears that my brother had found yet another good pipe. Using the information from the blog and the web I was able to learn a lot about the particular pipe I had in my hands. The stamping told me it was a pipe made by the Jost’s Pipe Shop in-house pipe maker, Harvey Raspberry. The pipe was stamped Jost’s Supreme on the left side of the shank. In all likelihood it is a Jost’s Old English Supreme. The majority of the Old English version pipes are marked Supreme. The pamphlet quoted above from the blog said that these pipes were stained in a darker color and were presumably from the same Algerian Aged Briar as the De Luxe. The pipes were of the highest quality available. I was not able to determine the age of the pipe.

My brother took the photos that follow. They show the pipe before he cleaned it up and sent it to me. It has some nice looking briar under the grime and dirt of the years. It looks to me like it had a natural finish on the bowl rather than the dark stain mentioned above.The next photos clearly show the stamping on the shank. The left side is stamped Jost’s over Supreme. The right side is stamped Imported Briar.The bowl and shank had a sticky black substance on the top of the grain. It looked as if it may have come from sticky labels used by the antique shop where the pipe was sold.The next close up photo shows the state of the cake in the bowl and the thick lava overflow on the top of the rim. It is hard to tell if the inner edge of the rim is damaged or not because of the thick cake. The second photo shows the nicks and cuts in the front top edge of the bowl and extending onto the rim. The stem was badly oxidized and there were a lot of tooth marks and chatter that had rounded the sharp edge of the button. The tooth marks and chatter were covered with calcification. The vulcanite was pitted and worn.My brother did an amazing job cleaning up the pipe. He scrubbed the sticky surface and all of the tars and oils on the bowl and the rim. He scrubbed it with a tooth brush and Murphy’s Oil Soap and removed the soiled finish on the bowl and much of the rim top lava. He reamed the bowl with a PipNet reamer and took the cake back to bare briar. He scrubbed the mortise and the airway in the shank with pipe cleaners, cotton swabs and alcohol. I took the following photos when the pipe arrived in Vancouver before I started refurbishing it. I took a close up photo of the rim top. He had gotten almost all of the lava off of the rim and all that remained was some slight rim darkening. I also took photos of the stem to show how much of the buildup had been removed before I got the pipe. There was a deep oxidation in the vulcanite. I used a Savinelli Fitsall Pipe Knife to clean up the reaming of the bowl. I smoothed out the remaining cake at the bottom edges of the bowl and smoothed out the inner edge of the rim.I used a dental pick with a slight spatula to scrape out the hard deposits of tar on the inside of the mortise. It took a little extra work but it cleaned up the buildup and made the stem fit against end of the mortise snugly.I scrubbed out the mortise and the shank and stem airways with pipe cleaners, cotton swabs and alcohol to remove the debris from my scraping work in the mortise. It did not take too many before the pipe was clean on the interior.I sanded the rim with 1500-4000 grit micromesh sanding pads to remove the slight rim darkening that remained. I was able to polish the rim. I used clear super glue and briar dust to fill in the deep nicks and gouges in the front face and top edge of the bowl. I sanded the bowl front with 220 grit sandpaper to smooth the surface and to blend it in with the surrounding briar. I polished bowl at the same time as I did the rim with the micromesh sanding pads.I used a needle file to sharpen the edge of the button and make it more defined. I sanded the stem with 220 grit sandpaper to remove the scratches on the stem left behind by the file and the oxidation in the surface of the vulcanite.I sanded the bowl and the stem with a medium and a fine grit sanding pad to remove the scratches and to polish the briar and the stem. With the majority of the oxidation removed and the scratches in the briar I worked on polishing the stem. I wet sanded it with 1500-2400 grit micromesh sanding pads and dry sanded it with 3200-12000 grit pads. I rubbed the stem down with Obsidian Oil after each set of three pads. After rubbing the stem down with a final coat of oil after the last set of pads I set it aside to dry. I buffed the stem with red Tripoli to further remove the light oxidation that remained in the vulcanite. I buffed both the bowl and stem with Blue Diamond on the buffing pad to polish it. I gave them multiple coats of carnauba wax and buffed it to a shine with a clean buffing pad. I hand buffed the finished pipe with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. I really like the way it turned out. The grain of the briar really stood out. The natural finish looked really good and the contrast in the flame and straight grain with the underlying briar is quite stunning. Thanks for walking through this journey with me.

Breathing Life into a Huge KBB Yello-Bole 3068C Bent Billiard

6 Replies

Blog by Steve Laug

A good friend of rebornpipes, Jim emailed me about a pair of pipes that he had that he wanted me to have a look at. The first of them is on the work table and it is going to take a bit of work to bring back to life. The second is the one I just finished and it is a beautiful pipe. It is a Yello-Bole like none I have seen before and I have worked on many of them over the years. This one is a large KBB Yello-Bole bent billiard similar in style to the WDC Wellington big pipes. This one is 10 inches long and 2 ¼ inches tall. The bowl is 7/8 inches in diameter and 1 ¾ inches deep. The stem was in decent shape other than oxidation and light tooth chatter on the top and bottom sides near the button. The button itself was very clean with a few tooth marks but the airway was in perfect condition. The stem has the older style inlaid Yello-Bole logo of the yellow circle on the top side. The stem appears to be a P-lip but it is the faux P-lip that has the airway coming out straight at the end of the P.

The finish on the bowl was dirty and the varnish coat was peeling away and flaking off around the bowl. There was a deep, rich oxblood colour to the stain underneath the peeling finish. The rim was dirty but otherwise it was pretty clean with no dents, dings or nicks in the surface or in the inner or outer edges of the rim. In the photos it appears that the bowl was meerschaum lined but I assure you that it was not – it is merely coated with the famous Yello-Bole Honey Curing yellow mixture. The bevel on the rim shows the yellow as does the bottom of the bowl. In fact, though the pipe was smoked it appears that it was never smoked all the way to the bottom of the bowl and the lower 1/4^th of the bowl still shows the yellow bowl coating. There was a light cake that was spotty around the inside of the bowl but it was not thick of overflowing onto the rim.

The stamping on the left side of the shank reads KBB in a cloverleaf/club and next to it Yello-Bole over Reg. U.S. Pat. Off. Under that it is stamped Imperial in script and below that the fourth line of the stamp reads Cured With Real Honey. The nickel ferrule on the shank end is stamped with the KB&B Cloverleaf and underneath reads Nickel Plated. It is interesting to me to see this stamping on the band. Typically the Yello-Bole pipes bore the KBB stamp without the ampersand (&) between the two “b’s” which is true on the logo on the left side of the shank. It simply reads KBB in the leaf. On the band however the logo has the KB&B stamp which is usually reserved for the better quality Kaywoodie pipes of the time. The right side of the shank is stamped Algerian Briar over 3068C which I assume is the shape number.

I took the photos below to show what the pipe looked like when it arrived and I had unpacked it on my work table. I took some close up photos of the bowl, rim and stem to show the condition of those areas when I received the pipe. You can see the clean bevel on the rim with the slight darkening of the yellow bowl coating and the light, uneven cake in the bowl. You can also see the yellow bowl coating on the bottom portion of the bowl. The stem shows the oxidation and the light tooth chatter on the top and underside near the button. You can also see the airway exiting the stem at the end rather than the top of the “P-lip”. I reamed the bowl with the Savinelli Fitsall Pipe Knife to clean the cake back to bare briar. I used that tool as I wanted to leave the yellow bowl coating intact in the bowl to leave it as original as possible.I scrubbed off the peeling finish with cotton pads and acetone (fingernail polish remover) until the surface of the briar was smooth and the oxblood stain coat shone through. I used 1500-2400 grit micromesh sanding pads to work on the rim top and the inner bevel of the rim until they also were clean. Once I had removed the varnish coat there were a lot of dings and dents in the rim and the sides of the bowl. I used a hot butter knife and a wet cloth to steam out the dents. It took some time but I continued to steam the dented areas on the bowl until I had removed all but the small nicks on the bowl. I took photos of the bowl after I had steamed it and you can see from the photos that the briar looked far better after steaming. I took some close up photos of the stamping on the shank and the nickel ferrule to show what I talked about in the earlier paragraphs. The nickel-plated ferrule had a lot of scratches in the surface of the nickel. You can also compare the KBB stamp on the shank with the KB&B stamp on the ferrule in the photos. I polished the nickel ferrule with micromesh sanding pads to remove the scratches. I started with 1500 grit and worked my way up to 12000 grit. It removed the scratches and also polished the nickel. I cleaned out the interior of the mortise, the sump at the bottom of the shank and the airways in the shank and the stem with alcohol, pipe cleaners and cotton swabs. The first photo below shows the clean briar in the shank.I sanded the stem with 220 grit sandpaper to remove the oxidation on the surface of the stem. I scrubbed it with the Before & After Pipe Stem Deoxidizer to lift more of the oxidation. I wet sanded the stem with 1500-2400 grit micromesh sanding pads and dry sanded with 3200-12000 grit pads. After sanding with each set of three pads I rubbed the stem down with Obsidian Oil. After sanding with 12000 grit micromesh I gave the stem a final coat of the oil and set it aside to dry. I buffed the bowl and stem with Blue Diamond on the buffing wheel to further polish the bowl and the stem. I was seeking to remove even the micro scratches left behind in the vulcanite by the micromesh sanding pads and the remaining scratches in the briar as well. I gave the pipe multiple coats of carnauba wax to protect the pipe. I buffed it with a clean buffing pad on the wheel and raise a shine. I personally do not like the high gloss look of a pipe when it first comes off the wheel so I hand buff it with a microfibre cloth to deepen the shine and give it a rich look. The finished pipe is shown in the photos that follow. I look forward to hearing from Jim as to his thoughts regarding this “rare to me” older KBB Yello-Bole. Thanks for walking with me through the process.

ADDENDUM:

Andrew commented below regarding the size of the pipe. I have added this photo of the pipe in my hand to give an idea of the size.

Cleaning and Restoring a Stanwell Antique 56 Canadian

1 Reply

Blob by Steve Laug

One of the first pipes I chose to restore from the estate lot my brother and I purchased in Idaho from an older pipeman, Gene was this Stanwell Canadian. It was a nice looking contrast stained pipe that was sandblasted over most of the surface area – the shank and ¾ of the bowl. The underside of the shank and the front of the bowl were smooth and stained a medium brown. The rim top was also smooth and had a matching stain. The stem was a replacement and while it fit the mortise well it did not fit against the shank. It was well chewed by what Gene called a beaver. The tooth marks were deep and many. Fortunately the stem did not match the shank of the pipe so it would not be a loss. I would need to look for a stem in my can of stems and see if I could find one that matched the stem. Maybe I would even find one that bore the Stanwell logo and worked with the pipe. My brother Jeff took some photos of the pipe before he cleaned it up. The next photos show the pipe when he received it.Jeff took close up photos – the first shows the cake in the bowl and the overflow of tars and lava over the top of the rim. The outer and inner rims were in great shape. The bowl was still in round and the outer edge is smooth where the smooth portion is and rougher where the sandblast portion of the bowl was. The underside of the shank was stamped Antique in script over Made in Denmark. Next to that it was stamped Stanwell. Next to the shank/stem junction it bore the shape number 56 which is the shape number for a long Canadian. He also took some photos of the stem top and bottom. I have included them as they show the chewed surface of the stem on the top and the bottom side. It was a mess and the button was chewed down as well.When the pipe arrived in Vancouver I took a photo of the pipe with the stem that came with it. I went through my can of stems and found a stem that bore the silver Stanwell logo on the top side of the saddle. It fit the shank well and with a little cleanup it would work very well. It was oxidized and had some light tooth chatter on both sides. It was almost straight from the shank to the edge of the button.I removed the stem and took photos of the bowl without a stem to give you an idea of the condition of the bowl and shank of the pipe. You can see from the photos that my brother had cleaned up the exterior of the pipe with Murphy’s Oil Soap and a tooth brush and removed the grime that was in the grooves and crevices of the sandblast finish. There was also a small fill on the front of the bowl on the smooth portion of the bowl front. He was also able to remove much of the tars and lava on the rim top. I took a close up photo of the stem – both top and bottom sides in order to show the general condition. You can see the crown S on the top of the saddle portion of the stem.The tenon was the perfect size to fit the mortise on the Canadian. The width of the stem was the same as the shank. The height was slightly larger than the height of the shank. It would need to be sanded lightly to bring about a match. The photos show what the pipe looked like with the new stem. I took a close up photo of the bowl rim and the underside of the shank. It was in great shape. The stamping on the shank underside was clear and readable. I also took a close up photo of the stem top and underside with it in place in the shank. You can see from the photos that the stem fit nicely in the shank and looked like it belonged on the pipe.I sanded the stem with 220 grit sandpaper to remove the tooth chatter and the tarnishing to the crown S logo. I worked on the height of the stem so that it was more in line with the thickness of the shank.Once I had the stem fit better I polished it with micromesh sanding pads – wet sanding with 1500-2400 grit sanding pads and dry sanding with 3200-12000 grit sanding pads. I rubbed the stem down with Obsidian Oil after each set of three sanding pads. I gave it a final coat of oil after the last set of three pads and set it aside to dry. I rubbed the bowl down with a light coat of olive oil and hand buffed it with a shoe brush. I gave it several coats of Conservator’s Wax and buffed it with the shoe brush. I buffed the smooth portions on the bowl and rim with Blue Diamond and buffed the stem as well to polish it. I gave the stem and smooth portions of the bowl with carnauba wax. I buffed the entire pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. The shine and the contrast finish and stains make the pipe a unique looking pipe. The new stem looks right with the pipe. Together they combine to make a good looking pipe. Thanks for walking through the restoration with me.

Restoring another Classic Find – a Dunhill 4R Root Briar Canadian EC

5 Replies

Blog by Steve Laug

My brother and I recently purchased some pipes from an estate sale from an old pipeman named Gene in Pocatello, Idaho. There were a lot of great pipes in the lot. I have written about the pipes on a previous blog: (https://rebornpipes.com/2016/10/07/a-good-day-hunting-orchestrated-between-british-columbia-and-idaho/). On his way home my brother stopped at an antique shop and found pipes that were by far the most prestigious of the finds. These included a Charatan’s Make Canadian Sandblast 0121, the Four Dot Sasieni Pembroke with a patent number, Pat.No. 150221/20, what we thought was a Dunhill Bruyere Canadian EC 4R (Once I got it I was pretty certain it is actually a Root Briar) and a Jost’s Supreme Diamond Shank bent billiard. I wrote about the restoration of the Sasieni earlier (https://rebornpipes.com/2016/11/05/restoring-a-classic-find-a-sasieni-four-dot-london-made-pembroke/). The second pipe that I have chosen to restore is the Dunhill Root Briar EC 4R Canadian.

When my brother was cleaning up the pipe he called me and let me know that he had found a Dunhill on his recent hunt. He was excited and surprised by the find. The pipe obviously had a replacement stem as there was no white dot. The stamping had been buffed so much that it was unreadable except with a bright light and a lens. He read me the stamping on the shank. Near the bowl on the left side of the top of the shank it was stamped EC and mid shank on the left it read Dunhill over Root Briar. On the top right side mid-shank it read Made in over England with a 6 next to the D. That would make it a 1966 pipe if I am not mistaken. Next to the bowl shank junction on the same side it read circle 4R. The EC stamping told me that I was dealing with a Canadian. The R following the circle 4 told me that the pipe was a Group 4 sized Root Briar. He had found a good one. The only thing that would have been better was if it had come with the original stem. My brother took the photos that follow. They show the pipe before he cleaned it up and sent it to me. It had some nice grain on the bowl and shank.He took some close up photos of the bowl and stem. The first one below shows the condition of the rim. It had some tars on the surface but otherwise appeared to be in great shape. The inner and outer edge both looked good. There was a light cake in the bowl as well. The second and third photos show the oxidized and calcified stem. There was some light tooth chatter on both sides near the button. The replacement stem appeared to be well made. The next two photos show the condition of the stamping on the top of the shank from both the left side and the right side. It was faint and over buffed but with a light and lens still readable.My brother carefully cleaned the externals of the pipe with Murphy’s Oil Soap and was careful in the process to not further damage the stamping. He reamed the bowl and scrubbed the rim to remove the tars and oils. He cleaned out the interior of the pipe with pipe cleaners, cotton swabs and alcohol leaving the mortise and the airways in the shank and the stem clean. The next photos show what the pipe looked like when it arrived in Vancouver. While the rim was free of debris there was still a lot of darkening and thin coat of tar on it. It would not take too much to clean off the surface. He had been able to remove much of the calcification on the stem and clear up some of the scratches on the stem. I sanded the stem with 220 grit sandpaper and removed the oxidation and the tooth chatter. There were some light tooth marks as well that I was able to sand out and leave the surface of the stem smooth.I gave the stem a light buff with Tripoli to polish it lightly and then drill it for a replacement dot on the top side. I used an ivory/white coloured knitting needle that I trim down to fit as a dot. I chose to make the dot larger than the normal white dot on these pipes to make it clear that it was a replacement. I marked the spot on the top of the stem with an awl and started the hole. I drilled it with a Dremel.I painted the shaped end of the knitting needle with clear super glue gel and then inserted it in the drilled hole in the top of the stem. I cut it close to the stem with a pair of nippers and then sanded it with the Dremel to get as close as I could to the surface of the stem and then finished sanding it with 220 grit sandpaper to blend it in with the stem surface. You can see from the second photo that it is slightly larger than the standard Dunhill dot. I polished the stem with micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding it with 3200-12000 grit pads. I rubbed the stem down with Obsidian Oil after each set of three pads. After the final set of three pads I gave it a final rub down with the oil and set it aside to dry. In the photos below the dot looks like it has a blue tint but in person it is a bright white. I sanded the bowl and the shank with the micromesh sanding pads, avoiding areas where the stamping resided so as not to further damage it. I worked on the rim with the pads to further remove the darkening and light oils that still remained. I gave the bowl a light rubdown with olive oil to bring some life back to the natural finish of the Root Briar.I carefully buffed the bowl and stem with Blue Diamond on the wheel and gave them both several coats of carnauba wax. I buffed the pipe with a clean buffing pad and hand buffed it with a microfibre cloth. The finished pipe is shown in the photos below. While the stem obviously cries out that it is a replacement and the white dot says the same the overall look of the pipe is beautiful. The warm glow of the root briar finish looks really good. This old classic should be good to deliver a great smoking experience for many years to come. Thanks for walking with me through the process.

A Pair of Rainy Day Pipes – More Adventures in Oddities

3 Replies

Blog by Steve Laug

Have you ever heard of Bartlett Pipes? They are rather strange upside down looking pipes in my opinion. My brother sent me this link to a youtube video on the Bartlett pipes. We were both searching for information on the brand as neither of us had heard of them or seen them close up before. https://www.youtube.com/watch?v=dyFfLidMmws&feature=youtu.be

What made the hunt for information regarding this oddity necessary was that my brother had bid on two of these and won both of them on eBay. One of them was NOS (new old stock) and one of them was smoked and well used. In the past I had seen photos and read on the online forums about these pipes but had never really done any research to figure out what they were. They were always a bit of an oddity to me. Either way the stem sat they did not look right and when you removed the cap at the top the airway was almost at the top of the bowl (if the screw on lid was to be considered the top). The angles of the shank and the curve of the stem leads me to think that the capped surface was the top of the bowl. The bottom side of the bowl was a screen that allowed for airflow through the bowl. I am still trying to figure out if you light the pipe from the bottom or the top of the bowl. From what I read on the various online forums and in the articles that I could find I was able to piece together how the pipe functioned. The pipe bowl was open at the top and the bottom. The airway into the shank was near the top opening and led directly to the pipe stem. A polished aluminum cover is screwed onto the threaded briar bowl top and is left in place when the pipe is smoked. At the other end of the bowl there is a screen that covers the bottom opening that keeps the tobacco in the bowl while permitting access to the tobacco to light it. The screen is supposedly fine enough that the ash does not fall out of the bowl into the lap of the smoker. With the cover in place on the top opening, the tobacco is ignited via the screen on the bottom, causing the tobacco to burn from the bottom up. New tobacco may be added at any time by removing the cap from the top of the pipe. It is said that the burning the tobacco from the bottom reduces the moisture that usually collects and thus makes it unnecessary to dry out the bowl between pipes. The bottom lighting also makes lighting the pipe in the wind or rain much simpler.

The next photos show the screened bottom of the two pipes that I was going to work on. The smooth pipe is new and unsmoked the sandblasted pipe is used and you can see some charring around the inner edges on the bottom of the bowl. The bowl bottom on the unsmoked pipe was stained black to minimize the darkening that occurs when the pipe is lit.Both pipes were stamped with the name Bartlett over a Patent Number – 4235252. The stamping on the sandblast version was on the right side of the shank and the one on the smooth was on the left side of the shank. Both stampings were very sharp and legible. The smooth briar pipe was also stamped on the right side of the shank with the work Imported Briar.At this point I wanted to know more about the pipe. It was a brand that I was unfamiliar with. In usual unhelpful fashion I found that the Bartlett Pipe was made by the Bartlett Pipe Company Inc. of Bartlett, NH (which I assume is New Hampshire).

On the Pipesmokers Forum I found some interesting information from a friend of the inventor of the pipe. Here is the link to the conversation on that website. http://pipesmokersforum.com/community/threads/an-interesting-surprise.46690/

Adam Hirshan comments: “A friend of mine invented and patented a revolutionary smoking pipe that lights from the bottom. A major manufacturer saw the promise and bought the idea 15 years ago, but it never took off. My friend got the patent back a few years ago and we’ve developed a new rock maple version that we call The Freedom Smoking Pipe.”

“It smokes cool and easy. A stainless steel screen holds the tobacco and ash in place – nothing falls out. No moisture or resin accumulate in the bowl. A cork and leather top makes it wind and rain proof.”

“We had initial success wholesaling through a well-known distributor. We were in about 100 tobacco shops nationwide, and appeared in the Levin catalog. Response from our early customers was strong – most loved it, some hated it. Then interest dropped off and left us wondering what happened.”

I did some more digging and found some information on the Dr. Grabow Collectors Forum. Here is the link: http://drgrabows.myfreeforum.org/viewcardtopic.php?t=1236

I quote: “I was asked what I thought about my Bartlett pipe and figured I’d start a new topic. If you don’t know what it is, it’s the ‘Upside down pipe’. The history as I know it is there have been 3 variations. It was invented in the 70’s. Sparta picked up the rights and produced them in the 80’s for 8-10yrs. Didn’t take off. Rights were returned to the inventor. Seems they are no longer produced. (ed. This seems to go along with the information from Adam Hirshan in the above comment).”

The quote goes on with an interesting reference to the Sparta example of the pipe: “Mine has a red stain, and the chain to hold the cap. My stem is from a junk pipe I had. The weirdest thing is not seeing the baccy burn. First smoke required a tamp halfway through and the bowl got dang hot! Second time out, the pack was perfect. One light, no tamp. Just weird not tending the bowl like normal…….Guess this is why the never went anywhere.”

I was also able to find the patent information for US Pat.4235252. Interestingly it read much like an earlier paragraph that I pieced together regarding the pipe. Here is the document in full. First the written description and then the drawings of the pipe. It read that “the patent was for a smoking pipe having improved smoking characteristics. The smoking pipe includes a bowl having top and bottom openings and a breather hole near the top opening and in communication with a pipe stem. A cover assembly is attached to the bowl adjacent to the top opening and covers the top opening when the pipe is to be smoked. A retainer having a screen cooperates with the bottom opening for retaining smoking tobacco within the bowl while permitting access to the tobacco for the ignition thereof. The retainer may also be removed from its position relative to the bottom opening for the removal of ashes. Tobacco is inserted into the bowl via either opening, but preferably via the top opening and to a level just below the breather hole. With the cover assembly covering the top opening, the tobacco is ignited via the screen of the retainer, causing combustion of the tobacco in a bottom-to-top fashion. New tobacco may be added to existing tobacco via the top opening and ashes may be removed via the bottom opening, even as the smoking process takes place. The bottom-to-top combustion minimizes puddling of tobacco juices or the requirement of drying out periods and facilitates lighting the pipe in the presence of wind, rain, etc. The lack of obstruction of the breather hole by the presence of tobacco results in a smooth draw with the generation of a substantial, satisfying volume of smoke.” (ed. On the two pipes I have the screen on the bottom is not removable and the top is a threaded aluminum cap.) My brother took some photos of the sandblast version of the pipe that shows the shape but also interestingly shows a hidden benefit. When he removed the cap from the top of the bowl the bowl was already filled with a broken flake tobacco. Unfortunately it was dry and crumbled to dust when he cleaned out the bowl. My brother cleaned and reamed the smoked sandblast pipe and cleaned out the dust from the unsmoked smooth one. He scrubbed the briar with Murphy’s Oil Soap and cleaned out the mortise and the airway in the shank and the stem. The stems on both pipes were lightly oxidized and on the smoked pipe there was a small tooth dent on the top of the stem near the button. I took the following photos to show what the pair looked like when I brought them to my work table. He did a great job cleaning up the aluminum caps on both the inside and the outside. He also cleaned up the thread on the top of both bowls allowing the caps to screw on easily.He cleaned the screen on the smoked pipe with cotton swabs and alcohol until it looked as good as the unsmoked pipe. The inner edge of the rim on the bottom of the bowl was charred and showed some wear and tear from lighting the pipe from the bottom. I think one of the draw backs on this pipe is not being able to see the flame hitting the tobacco. The rim on this bowl shows significant rim damage.I took close up photos of the stems to show the light oxidation – it is not deep in the vulcanite and the overall condition of the stems. The stem on the sandblast pipe had a small pinprick tooth mark on the top of the stem. I have circled it in red on the first photo below.I took some photos of each of the pipes before I cleaned them up. They really were in pretty decent shape. There were some rough spots on the bottom of the bowl around the inner edge of the rim but it looked to be original. The smooth briar is new and has a shiny varnish coat that I decided to leave as the pipe is NOS. It was interesting to me to note that the bottom of the bowl was stained with a flat black stain on the new pipe so when I restored the smoked version I would match them. The sandblast is also in really good shape other than the inner edge of the bottom rim on the bowl. On both pipes the aluminum cap was in perfect condition on both the inside and the polished outside of the cap. I took photos of the pipes with the covers removed and the bowl tilted to give some idea of what the inside of the bowl looked like. It really is no more than a tube with a cap on one end and a screen on the other end. I used the topping board on the damaged bottom of the bowl. I topped it (or maybe bottomed it is more appropriate) until the damage was removed.The small crevices that had opened around the inner edge of the bowl were not really cracks but rather areas that had burned with the heat of the flame. I filled them with briar dust and super glue to make them smooth and then retopped the bowl to smooth them out. I stained it with a black aniline stain and touched it up after sanding the repairs.I sanded the two stems with 220 grit sandpaper to remove the oxidation on the surface of both stems. I used a spot of clear super glue to fill in the tooth mark and sanded the repaired area smooth to match the surface of the stem. I polished both stems with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I rubbed the stem down with Obsidian Oil after each set of three pads. After the last pad I gave it a final rubdown with the oil and set it aside to dry. I took a photo of the pipes and stems before I took them to the buffer to show what they looked like at this point in my restoration.Here are some photos of the bowls from a variety of angles. There is a nice blasé and some pretty grain – they are a nice pair of pipes. I buffed the pipes with Blue Diamond on the buffing wheel and then gave the stems several coats of carnauba wax. I gave the sandblast bowl several coats of Conservator’s Wax and left the varnish coat alone on the smooth briar bowl. I buffed both pipe with a clean buffing wheel to raise a shine. I hand buffed them both with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. It is a unique piece of pipe and tobacco history. It certainly speaks of the inventiveness of pipesmokers who are perpetually looking for the better and drier smoke. Thanks for taking this journey through the restoration and the history of the Bartlett pipe.

Rejuvenating a Gasparini “Fatta a Mano” Camuna

1 Reply

Blog by Steve Laug

My brother Jeff has an eye for unusual pipes that he thinks might intrigue me. He outdid himself this time. He found an odd three-part pipe – a base, a bowl and stem that I would classify as a churchwarden. It is about 10 inches long and the bowl is 3 inches tall but at the same time it is dainty, delicate and artsy. It is not a heavy pipe and the thin pencil stem and the bowl and base make it seem smaller than it is. The first two photos below show the unique shape and you can get a sense of how the pipe is both big and delicate at the same time.The next photos give a sense of the artistry of the pipe. The base is stained a light brown and has a shallow sandblast finish. The end of the shank is rounded. The stem should sit against the shank end but the mortise needs to be cleaned and the oxidation on the tenon needs to be removed to make that happen. The bow is threaded and screws into the base. It has a contrasting dark brown and medium brown stain coat that gives contrast in the deeper blast and also with the base. The next photos are close up pictures of the bowl and base. The first shows the bowl removed from the base. You can see from the photo that the bowl is threaded to be screwed into the base. The base and the bowl are dirty. The bottom of the bowl has two air holes that go into the bowl. The one toward the bottom of the photo below shows that a chunk of briar has broken away from the side of the hole and the threaded portion.The second and third photos show the inside of the base and the cake and rim of the bowl. It is dirty but the rim and base are in excellent condition. There is some build up on the area of the base where the rim sits. It will need to be cleaned. To me it looks like it is a combination of dust and wax.The next two photos give a clear picture of the damage to the base of the threaded portion of the bowl. You can see the damage on the outer edge of the tip and to the threads. It looks like a chunk of briar has broken free and a lot of debris and tars have filled in the damaged area.The next photos show the base and the bowl from different angles. The grain and the blast is quite nice and the contrast of stains on the bowl look really good in contrast to the lighter stained base. The fourth photo shows the stamping on the bottom of the base. It reads R. Gasparini over CALUMA over script that reads “Fatta A Mano” which translates as Made by Hand. The next photos show the stem with the tooth chatter and marks on the top and bottom side near the button. They also show the oxidation and the loss of colour in the G script logo on the side of the stem.I know nothing about Gasparini brand so I looked up the website of the brand and found that the “Fatta a mano” stamped signified a particular freehand style line that Gasparini did. Here is the link to their website http://www.mgasparini.it/en/category-product/hand-made/.

I also looked up the brand on Pipedia. There is a lot of the history of the brand there for those who want to read the article in full. Here is the link: https://pipedia.org/wiki/Gasparini. I quote from that article in part.

“In 1938 Mario Gasparini, with his wife Ida, took his first steps into the world of the pipe. Today his daughter, Marisa Gasparini, sits at his desk. Since 1977 Marisa and her husband, and now her daughter, carry on the tradition of her family…”

“At the beginning of 1950’s, the building, that still today hosts the production department, was enlarged. In 1971 the offices and the warehouse were moved from Milan (where they were situated for marketing purposes) to Luvinate.”

“During those years the skilled workers and our direct partners have always followed the history of the Gasparini factory, becoming very fond of it and devoting themselves, with care and love, to the making of each pipe, with the personal fantasy and skills of the artist…”

“…The cycle of manufacture is basically divided into two separate branches. Pipes from the first branch (my addition, ed.) the “Fatta a Mano” and “da Collezione” are completely hand made, rigorously produced from the best selected briar; the estrus(?) and fantasy of our masters is surely more evident in these series of pipes.”

“The other branch is (my addition, ed.) …Serial pipes are partially machine made (the bowl, shank and drilling) and they are divided into various categories based on the quality and finish.”
“…during the years we have always made the creation of unique pieces for the series “Fatta a Mano” (Hand Made) and “per Collezionisti” (for collectors).”

At the bottom of the Pipedia article there was an email address for contacting the Gasparini Company with any questions that need to be addressed to them. I took the opportunity last evening to write an email to them regarding the age and provenance of the pipe I had in hand. I also included a photo of the pipe’s condition and look when I got it from my brother. This morning I received a reply from none other than Marisa Gasparini herself. Here is her email in full:

Dear Steve,
The pipe you have is a very old pipe that we produced 35 years ago about, and we made only few pieces.

It’s very different from the normal pipes and we have made in the time other interesting pipes, quite original that we keep in our warehouse.
If you are interested I can send you some photos for next week so you can understand what I mean for original.

I would like to know where you bought that pipe, thanks a lot and best regards,

Marisa Gasparini

That gave me some incredibly helpful information. The pipe in my hand is approximately 35 years old and there were only a few of them made at that time. She is going to send me some photos of some of the original pipes next week. I will post them as an addendum to this blog when I receive them. I wrote Marisa back immediately thanking her and answering her question as to where I found the pipe.

Now I had a feel for the age and provenance of the pipe and I was ready to work on it. I took some photos of it before I worked on it. My brother had done the majority of the clean up work on the bowl, base and shank before he sent it to me. He had reamed it and cleaned out the airways in the bowl, base, shank and stem. He scrubbed the externals and remove a lot of the waxy grime that had collected on the bowl over the years. It looked pretty good when I received it. I took the stem out of the pipe and unscrewed the bowl from the base and took some photos of the pipe before I worked on it. I took a photo of the stamping on the bottom of the base to give an idea of how that look – it is the only smooth portion on the base other than the rounded shank end.I took some photos of the damage to the bottom of the bowl on the threaded portion to show what it looked like with the oils and tars removed. I took a top down photo to show the cleaned bowl and also the twin airways in the bottom of the bowl. I cleaned up the reaming with a Savinelli Pipe Knife and scraped out the bits of cake that still were on the walls and at the bottom of the bowl.I wiped down the bottom of the bowl and the damaged area with alcohol on a cotton swab and cotton pad in preparation for repairing the damage. I used clear super glue and briar dust to build up the area of the missing chunk of briar. I was careful to keep the airway open. I layered the glue and the dust until it was smooth.I used the sanding board to lightly “top” the bottom of the bowl and smooth out the repaired area. After I took the second photo below I used needle files to retrace the threads on the damaged area of the bowl.I gave the bowl and base several coats of Conservator’s Wax and buffed them with a shoe brush. The photos below show the bowl and base at this point in the restoration. I turned my attention to the oxidation on the stem. I lightly sanded it with 220 grit sandpaper to remove the surface oxidation and remove the tooth marks and chatter from the area around the button. I ran a long pipe cleaner through the stem just to check for debris and oils but my brother had done a great job with the airways. I scrubbed the stem with Before & After Pipe Stem Deoxidizer and the with the Fine and Extra Fine Pipe Stem Polish. I was able to get the majority of the oxidation off the stem.I did a touch up on the “G” logo on the stem with white model paint and a fine bristle artist’s brush. When it dried to touch I used a 1500 grit micromesh sanding pad to remove the excess paint and polish the end of the stem.I polished the stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I rubbed the stem down with Obsidian Oil after each set of three pads. After the final set I buffed it with Blue Diamond on the wheel and gave it a last rub down with Obsidian Oil. I set the stem aside to let the oil dry. I buffed the stem with carnauba wax and with a clean buffing pad to raise the shine. I lightly buffed the bowl and base with Blue Diamond and then gave it a light coat of carnauba, being careful to not let it build up in the grooves and crevices of the sandblast. I buffed it with a clean buffing pad to raise the shine. I put the pipe back together and gave it a final buff with a clean buffing pad to shine it. I hand buffed it with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. I took photos of the pipe as a whole and also taken apart in the various configurations. I am really pleased with the finished pipe and look forward to giving it a smoke. To me it is a very “Gandalfian” looking pipe and feels great in the hand and the mouth. Thanks for walking with me through the history and the process of bringing the pipe back to life.

Amazing Grain came alive on a Zeppelin Style Safe-Tee Patent Pipe

1 Reply

Blog by Steve Laug

When my brother sent me a photo of another cigar pipe he was bidding on I wondered about it. I have cleaned up two of them made by Mastercraft (https://rebornpipes.com/2016/09/12/back-in-flight-a-pair-of-mastercraft-sparkless-cigar-pipe-zeppelins/). They were an interesting pair of pipes. This one was different he said. The design was quite a bit more streamlined and smooth in terms of look. The aluminum nose cone was smooth and there were two air holes drilled in the briar itself rather than just in the nose cone. I am assuming this was to aid airflow in the pipe. It still had an aluminum to briar connector for the two parts. The vulcanite stem was well fitted. What would be the left shank side was stamped SAFE-TEE over Pat. June 23, 1925. I did a lot of searching online and could only find one other picture of a rusticated version of the pipe. It is not listed on Pipedia or on pipephil’s Logos and Stampings site. I looked in my reference books here and found it listed in Who Made That Pipe. In classic form, giving an almost dictionary style definition the book says that the pipe was made by the Safe-Tee Pipe Company in the US. Now to me that is classic – the SAFE-TEE pipe made by the SAFE-TEE Pipe Company. The only additional piece of information was that it was made in the USA and it was patented originally in 1924. The photo below shows the stamping. The stem was in great shape with minor pitting and some tooth chatter but no heavy damage. There was light oxidation as well.My brother took the photos above and the ones below to show the condition of the pipe before he cleaned it. The next one shows the pipe taken apart. The nose cone portion of the pipe is all briar with threads cut into the briar. The shank portion has an aluminum connector that turns into the briar cone. There is a washer that serves as a spacer/band between the portions. The stem is straightforward with no stinger apparatus. He also took photos of each side looking down the barrel. The washer is free and spins on the aluminum connector. It needs to be aligned for the two sides to meet properly. There was a small crack/flaw in the briar of the shank portion of the pipe.Once again I am thankful for my brother Jeff’s cleaning skills. The inside of the pipe and stem were spotless when it arrived in Vancouver. The exterior had also been scrubbed clean of dirt, debris and the mottle finish. The pipe was ready to restore. I took some photos of it when I brought it to my work table.I took some photos of the pipe taken apart to show some of the structure on the pipe. You can see the internals of the connector and the metal tube in the bottom of that portion (the one on the left of the photo) you can also see the end of the cone. It is an interesting design that is different from the Mastercraft version.The next photos show the condition of the stem – you can see both the tooth chatter and the oxidation in the photos. There was also some pitting in the vulcanite.My first order of business was to repair the crack and several of the deeper pits in the briar. I cleaned the entire pipe with a cotton pad and acetone. I examined the crack to see how deep it went in the briar and was pleased to see that it was really surface flaw. The tube inside the shank portion stabilized it from causing further damage. I used a dental pick to clean it out and filled it in with clear super glue. It was small enough that I did not mix any briar dust with the super glue repair.When the glue dried I sanded the repairs with 220 grit sandpaper to blend them into the surrounding briar and make them smooth.I sanded the repaired areas with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-4000 grit pads. I used the higher grit pads on the entire area around the repairs.I used a dark brown stain pen to touch up the repaired areas and blend them into the colour of the briar on the rest of the pipe. I gave the pipe a coat of Conservator’s Wax and buffed it. I set it aside and turned my attention to the stem.I did not stain the rest of the pipe but decided to leave it as it was. The repaired areas were stained to match the rest of the pipe but other than that it is unstained by me. I took the next two photos of the repaired areas after waxing and hand buffing them. The repairs blend in very well.I sanded out the tooth chatter and pitting on the stem with 220 grit sandpaper. It also removed the majority of the oxidation.I polished the stem with micromesh sanding pads – wet sanding with 1500-1800 grit pads and dry sanding with 2400-12000 grit pads. I rubbed the stem down with Obsidian Oil after each set of three pads. After the final set of pads I gave it a final coat of oil and set it aside to dry. I buffed the pipe with Blue Diamond on the buffing wheel being particularly careful around the stamping on the side. The stamping was already light on the left and right side so I did not want to damage it more. I gave it multiple coats of carnauba wax and buffed it with a clean buffing pad to give it a shine. I finished by hand buffing it with a microfiber cloth. The finished pipe is shown in the photos below. It turned out to be a beautiful piece of briar with a mix of flame, cross and birdseye grain surrounding the two halves. The aluminum polished up nicely and the black vulcanite, the natural finish and the aluminum combine to give the pipe a classic appeal. This was a fun one to work on. Thanks for walking with me through the process.