Tag Archives: sanding a stem

A Strangely Unique Standing Churchwarden called a Television Pipe

Blog by Steve Laug

The next pipe on the table is an interesting pipe that caught my attention this morning when I was going through the boxes of pipes I have here awaiting restoration. This pipe was purchased from an online auction early in 2020 from St. Albans, West Virginia, USA. It has the length of a churchwarden and is a two part bowl and base with a tall bent stem. The pipe is a standing pipe that is well balanced and still stands when it is put together. The pipe is stamped on the left side of the shank and read TELEVISION PIPE and on the right side it read Algerian Briar [over] Made in France. There is a metal band/ferrule on the shank that is stamped EP in a diamond which means Electroplated and below that it has some very worn hallmarks. It was extremely dirty with grime and grit ground into the bowl sides. The bowl was heavily caked and there was a thick lava coat on the rim top and edges. The bowl unscrewed from the base which was also thickly caked with tars and oils. The band/ferrule was oxidized as was the vulcanite stem. There were light tooth marks on both sides of the stem ahead of the button. There was a small aluminum stinger in the tenon that was removable. Jeff took photos of the pipe before he started his work on it.He took some photos of the bowl and rim top to show their condition. The cake is thick and there is debris on the walls of the bowl. The rim top has a thick coat of lava and between that and the cake it is hard to know the condition of the rim edges. Clean up will reveal the condition. There are chips and nicks in the outer edge of the bowl. The stem looks pretty good with light tooth marks on both sides. The stem is oxidized and calcified. He took photos of the bowl and base together to show the overall appearance of the pipe. There is a lot of grime around the junction of the bowl and base that can be seen in the photos below. He unscrewed the bowl from the base and took a series of photos to show the condition of the bowl and the base. You can see the thick oils and tars in the threads, on the bottom of the bowl and in the base of the pipe. It is really a mess and will be a major work to clean up. Jeff took photos of the stamping on the sides of the shank and on the electro-plated band/ferrule on the shank.He remove the stem from the base and took a photo of the tenon end and shank to see the built up tars on the tenon and in the inside of the shank. You can also see the tarnish on the band.I looked on both Pipephil’s site and Pipedia to see what I could find out about the brand. There was nothing listed on either site regarding that brand. I turned a site that has been helpful in identifying pipes called Smoking Metal (http://www.smokingmetal.co.uk/pipe.php?page=277). The site shows a short version of this pipe – with a P-lip style stem on the shank rather than a Churchwarden stem. Other than the stem it is the same pipe. Since the information was quite limited on the brand it was time to turn to work on the pipe itself. I have to say that this was another pipe that I was really looking forward to seeing what Jeff had done to it. It is a French Made Algerian Briar Television Pipe that had shown such beauty through the grime that I was quite sure it would be stunning he cleaned it. He reamed the bowl with a PipNet pipe reamer and cleaned the remnants of cake back with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl and base with Murphy’s Oil Soap and a tooth brush to remove the grime and oils. He cleaned the internals of the base, shank and stem with pipe cleaners, cotton swabs and alcohol to remove all of the tars and oils there. He scrubbed the exterior of the stem with Soft Scrub to remove the oxidation and calcification. He wiped the bowl and stem down with a light coat of olive oil to rehydrate both. The pipe really was quite stunning. You can see the nicks around the bowl and base but they do not lessen the beauty of the pipe. I took close up photos of the stem and the rim top to show both how clean they were and what needed to be addresses with both. The rim top had some nicks in the top and the inner edge of the bowl was out of round. The stem looked better but the light tooth marks and chatter were still present.I took photos of the cleaned up stamping on sides of the shank. It is very clear and readable.I removed the stem from the shank and took photos to show the overall look of this beautiful pipe. I then unscrewed the bowl from the base and took photos of all of the parts of the pipe. I started my work on this pipe by dealing with the shrunken fills on the bowl sides. I filled them in with clear CA glue and briar dust. Once the repairs cured I sanded them smooth to blend them into the surrounding briar. I polished the briar with micromesh sanding pads – wet sanding with 1500-4000 grit pads. I wiped the briar down after each pad. The grain began to really come alive through the polishing. I took a break from the polishing process and I stained the sanded areas of the bowl with a Walnut Stain pen to blend them into the surrounding briar.I buffed bowl with Blue Diamond polish and then went back to polishing the bowl with 6000-12000 grit micromesh sanding pads. I repeated the process of polish the base with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the briar down after each pad. The grain began to really come alive through the polishing. I worked some Before & After Restoration Balm into the surface of the briar of both the bowl and the base with my finger tips. The product is incredible and the way it brings the grain to the fore is unique. It works to clean, protect and invigorate the wood. I put the bowl and base back together again and rubbed them down with the Balm. I buffed the bowl and base with Blue Diamond on the wheel. The finished bowl looked a lot better. I set the bowl aside and turned my attention to the stem. I polished the stem with micromesh sanding pads – wet sanding it 1500-12000 pads. I wiped it down with Obsidian Oil after each pad to protect it and preserve it. I polished it with Before After Pipe Polish – both Fine and Extra Fine. I finished the polishing with a final coat of Obsidian Oil. I am really happy with the way that this Tall Television Pipe Churchwarden Sitter turned out. It really is a unique looking pipe with character. The long mouthpiece is a unique feature of this pipe and sets it apart. The removable bowl and base work well and the pipe is a beauty. To me it is a great pipe with unique details. The grain really came alive with the buffing. The rich brown and black stains of the finish gave the grain a sense of depth with the polishing and waxing. The grain really popped. I put the vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Television Pipe Sitter really is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 10 inches, Height: 3 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 57 grams/2.01 oz. The pipe will be going on the rebornpipes store soon. It will be in the section on French Pipe Makers if you would like to add it to your collection.Thanks for reading this blog and my reflections on the pipe while I worked on it. It was a fun one to work on!

Not sure what to call this strange St. Claude, France GBD Coronet 753

4 Replies

Blog by Steve Laug

Sometimes when you are pipe hunting there is one that just grabs you. That was the case with this interestingly shaped GBD. Neither Jeff nor I had seen a GBD 753 shape before and never one with this style stem. The stamping on the bowl and the logo on the stem all seem to point to a later date for this one but the St. Claude stamp bring questions to that assumption. It is a bit of a mystery and was just one of those that spoke to us. We picked it up from an auction early in 2020 in Noberly, Maryland, USA. The pipe was stamped on the top of the shank and read GBD in an oval [over] Coronet. On the underside it read St. Claude [over] the shape number 753. The pipe itself was in filthy condition. The bowl was thickly caked and there was a thick lava overflow on the beveled rim top. The briar was very dirty with grit and grime ground into the surface. The stem was dirty and oxidized with calcification on the stem end. There were light tooth marks and chatter on both sides. There was a faintly stamped GBD logo in a rectangle that was very worn. Jeff took photos of the pipe before he did his clean up on it. He took some photos of the bowl and rim top to show their condition. The cake is thick and there is debris on the walls of the bowl. The rim top has a thick coat of lava and between that and the cake it is hard to know the condition of the rim edges. Clean up will reveal the condition. The stem looks pretty good with light tooth marks on both sides. The oxidation and calcification is present and clear. The logo stamp on the top of the stem is worn and light. It may not survive clean up. Jeff took photos of the sides of the bowl and the heel to give as sense of the shape and condition of the briar. It is a beautifully shaped pipe with some nice grain. He took photos of the stamping on the top and underside of the shank. The stamping is clear and readable as noted above. He also captured the logo on the stem top. You can see how faintly it is stamped and how it is fading. The line as new to me though I have worked on a lot of GBD pipes over the years. I turned to Pipephil’s site (http://pipephil.eu/logos/en/logo-gbd.html) to see what I could find. Sadly there was not any information on the Coronet line from France.

I turned then to Pipedia to first check the section on the history of the brand and see what I could find there (https://pipedia.org/wiki/GBD). I found some interesting information that helped to date the pipe to the time period between 1952-1981. I quote as follows from the section.

The Paris factory moved to Saint-Claude in 1952. Since 1981 the majority of GBD pipes come from the English factory. At about that same time GBD merged with Comoys, since then all production for both GBD and Comoy comes from a single factory.

The premium lines of GBD offered very good values, and are considered amongst the most affordable high end pipe of the 1960’s and earlier and a rival in quality, design, and price to Dunhill. Smokers’ Haven was the main retail supplier for GBD’s in the US until the early 1980’s.

GBD produced consistently well made pipes, almost entirely of Algerian or Grecian briar. In the late 1960’s to late 1970’s, they introduced the “Collector” and “Unique” lines, made primarily by Horry Jamieson, who had carved for Barling for many years, and was skilled in freehand design. Older GBD pieces are excellent smokers and unique in design. They did an excellent executions of classic pipe shapes, as well as some beautiful freehands in the “Unique” line.

I then followed the links to the list of models and information that was on each of the models/ lines of the brand (https://pipedia.org/wiki/GBD_Model_Information). I found the listing for the Coronet there. The quote further defined the time line of the pipe. It appears that it was made between 1951 and 1976 when it appeared in a catalogue. I quote as follows below:

Coronet — France, unknown if also made in England: Lower priced GBD, “take off” brown/black stained matt finish with “recessed platform” mouthpieces. – catalog (1976). These low cost pipes were possibly not always produced in normal GBD shapes.

I followed the links to another section of the brand that listed the shape numbers for me and I was able to find the shape I was looking for (https://pipedia.org/wiki/GBD_Shapes/Numbers). I quote the section below.

753 author one-eighth round

From all of that information I had learned that the pipe was a French Made GBD Coronet made in St. Claude France between 1951-1976. It was made with a matte finish and a recessed platform style stem. I also learned that it was an AUTHOR shape with a 1/8^th bend to the stem. Now it was time to work on the pipe.

I have to say I was really looking forward to seeing what Jeff had done to this French Made St. Claude GBD Coronet pipe when I took it out of the box. It had shown such beauty through the grime so I was quite sure it would be stunning. He reamed the bowl with a PipNet pipe reamer and cleaned the remnants of cake back with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and oils. He cleaned the internals of the shank and stem with pipe cleaners, cotton swabs and alcohol to remove all of the tars and oils there. He scrubbed the exterior of the stem with Soft Scrub and then soaked it in a bath of Briarville’s Pipe Stem Deoxidizer. He rinsed off the deoxidizer with warm water and wiped the bowl and stem down with a light coat of olive oil to rehydrate both. The pipe really was quite stunning. You can see the nicks on the heel of the bowl but they do not lessen the beauty of the pipe. I took close up photos of the stem and the rim top to show both how clean they were and what needed to be addresses with both. The rim top had some darkening around the outer edge at the front that would need to be addressed. The stem looked better but the light tooth marks and chatter were still present. I would need to remove those to bring the stem back.I took photos of the cleaned up stamping on the top and underside of the shank. It is very clear and readable.I removed the stem from the shank and took photos to show the overall look of this beautiful pipe.I decided to work on the nicks in the underside of the bowl with clear CA glue. Once it cured I sanded them with 220 grit sandpaper blending them into the rest of the bowl. I polished the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the briar down after each pad. The grain began to really come alive through the polishing. I worked some Before & After Restoration Balm into the surface of the briar with my finger tips. The product is incredible and the way it brings the grain to the fore is unique. It works to clean, protect and invigorate the wood. I polished the stem with micromesh sanding pads – wet sanding it 1500-12000 pads. I wiped it down with Obsidian Oil after each pad to protect it and preserve it. I polished it with Before After Pipe Polish – both Fine and Extra Fine. I finished the polishing with a final coat of Obsidian Oil. I am really happy with the way that this GBD Coronet 753 St. Claude Made Author turned out. It really is a beautiful looking pipe with great grain. The “recessed platform” mouthpiece is a unique feature of this pipe and sets it apart. I am not sure why this is a GBD Lower end model. To me it is a top grade pipe with great unique details. The grain really came alive with the buffing. The rich brown and black stains of the matte finish gave the grain a sense of depth with the polishing and waxing. The grain really popped. I put the vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished GBD Coronet Author really is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 1 ¼ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: 1 inch. The weight of the pipe is 49 grams/1.73 oz. The pipe will be going on the rebornpipes store soon. It will be in the section on French Pipe Makers if you would like to add it to your collection.Thanks for reading this blog and my reflections on the pipe while I worked on it. It was a fun one to work on!

I do not understand why Peterson coats some of their pipes with a thick varnish coat

2 Replies

Blog by Steve Laug

Yesterday afternoon Dallas (a long time pipe friend) stopped by to pick up a pipe I had repaired for him and to sit on the front porch and enjoy a bowl and some fellowship with each other. Due to COVID-19 we have only had virtual visits for over a year now so it was really good to see him and posit our solutions to the world’s problems. We covered a lot of topics that come naturally to men of a certain age! In the course of our discussion he brought out a very shiny Peterson’s Kinsale XL25 Made in the Republic of Ireland. The pipe was very glossy and it was one that he had in his collection for a long time. It should have been showing wear on the finish but this “plastic” coated looking finish was impervious to time and use it appeared. There was a slight bit of peeling on the rim top but other than that it looked like new. He handed it to me and told me his woes with this pipe. He said that the pipe became extremely hot when he smoked it. He had tried everything to change that but nothing mattered. Dallas has been smoking a pipe for almost 60 years now so it is not a technique issue. I am certain it is the fault of the thick “plastic” looking finish on the pipe. I have stripped other Peterson’s that had the same issue for him and the work always improves the dispersal of the heat. He wanted me to do the same with this pipe. I took a close up photo of the rim top to show the thickness of the cake and the peeling varnish on the rim top. The edges look very good and other than the bubbles in the varnish coat the top looks good. The stem is also shown to show the light oxidation of time on the vulcanite and the tooth marks and chatter that come from use.I took photos of the stamping on the shank to show the brand and the age of the pipe. It reads Peterson’s Kinsale on the top of the shank and Made in the Republic of Ireland on the underside. On the right side of the shank was the shape number XL25. The varnish had filled in the numbers showing that it had been varnished after stamping.I removed the stem from the shank and took a photo of the left side of the bowl to try to capture the shape and the grain. It really is a beauty.I like working on clean pipes so I reamed the bowl with a PipNet pipe reamer to take the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife. I sanded the bowl with 220 grit sandpaper wrapped around a piece of dowel. Once finished the bowl was clean and smooth. Now it was time to tackle the obnoxious varnish coat. I tried to remove it with straight acetone and came up with nothing. The seal on the finish was solid and seemingly impervious to my work at this point. I lightly sanded the finish on the bowl with a folded piece of 220 sandpaper to break through the surface. Once I had done that the acetone worked well to remove the finish from the briar. I repeated the process until the shiny coat was gone and I could feel the briar in my hand and see the grain without the top coat over it. I polished the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the briar down after each pad. The grain began to really come alive through the polishing. I worked some Before & After Restoration Balm into the surface of the briar with my finger tips. The product is incredible and the way it brings the grain to the fore is unique. It works to clean, protect and invigorate the wood. There is a rich shine in the briar but it is not that previous plastic-like shine. I cleaned the shank, mortise and airway in the stem with pipe cleaners, cotton swabs and isopropyl alcohol to remove the tars. Dallas had mentioned the stem was very tight but once I cleaned it the fit was just the way it should have been.I started polishing the stem with 1500-2400 micromesh sanding pads. I wiped it down after each pad with Obsidian Oil. I paused my polishing to touch up the P stamp on the top of the saddle with some Rub’n Buff Antique Gold. I worked it into the stamp with a tooth pick and buffed it off with a soft towel. I went back to the micromesh and polished the stem with 3200-12000 grit pads, again wiping it down after each pad with Obsidian Oil. I finished the polishing with Before & After Pipe Stem Polish, both Fine and Extra Fine. I gave it a final coat of Obsidian Oil before putting it back on the shank. Once the varnish was stripped off this is a nice looking Peterson’s Kinsale XL25 Pipe with an oval shank and a vulcanite saddle stem is a great looking pipe now that it has been restored. The briar is clean and the grain really came alive. The rich brown and black stains gave the grain a sense of depth with the polishing and waxing. The grain really popped. I put the vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Peterson’s Kinsale XL25 really is a beauty and feels great in the hand and looks very good. I think that Dallas will be very happy with it once he picks it up. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ½ inches, Height: 2 ¼ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 65 grams/2.29 oz. The pipe looks very good and I look forward to what Dallas thinks of it. Thanks for reading this blog and my reflections on the pipe while I worked on it. It was a fun one to work on!

I don’t like Painted Pipes – This Jeantet Meerlined Brummer 944 Billiard gives me pause

1 Reply

Blog by Steve Laug

This white Billiard with a Tortoise Shell acrylic stem came to us from an online auction early in 2020 from Columbus, Michigan, US. From the title of the blog you know that I am not a fan of painted pipes. That is probably because I have come to understand that the briar under the paint is quite often horrible and filled with putty and flaws. Paint covers a multitude of “sins” and I am sure this is no exception. Added to that the pipe is also meerschaum lined. What made me pause was the great looking tortoise shell stem and the gold shank band that give the pipe a touch of class. The painted surface was in good condition with no nicks of scrapes. The rim top had a bit of darkening on the meer lining and a little on the paint but even that was not too bad. The bowl did not have a cake which was also a bonus that helped. It is stamped on the left side of the shank and reads Jeantet [over] Brummer and has the shape number 944 stamped on the underside of the shank. The stem has the Jeantet logo on the left side – a J in an oval. On the right side it is stamped Hand Cut and on the underside it is stamped FRANCE. The Tortoise Shell stem is quite pretty but upon examination there is a round bite through on the top side just ahead of the button. Jeff and I had picked up several pipes that the previous owner had customized by filling in the slot with putty and drilling a hole in the top. It was obviously the owner’s attempt at making a “P-lip” style smoker. We are pretty sure this was one of them. In any case it would need to be reworked – opening the slot and filling in the hole on the top side. Jeff took some photos of the pipe before he worked on it. Jeff took photos of the bowl and rim top to show the meer lining and the condition of the rim and bowl. It has some darkening and light lava on the back side but otherwise looked good. He also took photos of the stem to show the hole in the top side. You cannot see it but there is a plug in the slot on the stem end that will need to be removed. Other than that the stem was in excellent condition.Jeff removed the stem from the shank to show the stepped down Delrin tenon and the gold band on the shank end. It is a pretty looking pipe and the shank is surprisingly clean looking.He took photos of the bowl and heel to show the condition of the painted surface. It is quite remarkable that it is in such great condition and appears to have been very well cared for by the previous pipeman or woman. Jeff took photos of the stamping on the shank and the logo on the stem. They read as noted above and were in excellent condition. I turned to Pipephil’s site to see what I could learn about the Brummer line of Jeantet pipes (http://pipephil.eu/logos/en/logo-jeantet.html). There was nothing specific about that line though was a brief summary of the history. I quote from the top bar below:

The company joined the Cuty-Fort Entreprises group (Chacom, Ropp, Vuillard, Jean Lacroix…) in 1992. In 2010 it dropped out and the brand isn’t part of the group any more. The label is owned by the Jeantet family (Dominique Jeantet) again. The pipe production is discontinued. Dominique Jeantet retired in 2000. See also: Antidote, Duke of Kent, Grand Duke, Hermes, Sir Bruce, Sir Duke

I turned to Pipedia to get a more detailed history of the brand (https://pipedia.org/wiki/Jeantet). There as a brief history there that I have reproduced below.

The firm of the Jeantet family in Saint-Claude is first mentioned as early as 1775. By 1807 the Jeantets operated a turnery producing in particular wooden shanks for porcelain pipes and wild cherry wood pipes. The firm was named Jeantet-David in 1816, and in 1837 the enterprise was transformed into a corporation as collective name for numerous workshops scattered all over the city.

The manufacturing of briar pipes and began in 1858. 51 persons were employed by 1890. Desirous to concentrate the workers at a single site, the corporation began to construct a factory edifying integrated buildings about 1891 at Rue de Bonneville 12 – 14. This took several years. In 1898 Maurice Jeantet restructured the business. He is also presumed to enlarge Jeantet factory purchasing a workshop adjoining southerly. It belonged to the family Genoud, who were specialized in rough shaping of stummels and polishing finished pipes. (In these times it was a most common procedure to carry goods from here to there and back again often for certain steps of the production executed by dependent family based subcontractors. Manpower was cheap.)

Jeantet was transformed to a corporation with limited liability in 1938. By that time a branch workshop was operated in Montréal-la-Cluse (Ain), where mainly the less expensive pipes were finished. 107 employees – 26 of them working from their homes – were counted in Saint-Claude in 1948 and 18 in the Ain facility.

The Saint-Claude factory was considerably modernized by ca. 1950 installing (e.g.) freight elevators. In 1952 the southern workshop was elevated. 80 workers were employed in 1958. The factory covered an area of 2831 m²; 1447 m² of the surface were buildings.

The climax of the pipe production was reached around 1969, when thirty to thirty five thousand dozens of pipes were made by 72 workers (1969). But then the production continuously dwindled to only six or seven thousand dozens in 1987 and only 22 workers were still there. Even though, around 1979 a very modern steam powered facility for drying the briar had been installed in the factory’s roofed yard.

Yves Grenard, formerly Jeantet’s chief designer and a great cousin of Pierre Comoy, had taken over the management of Chapuis-Comoy in 1971. Now, to preserve the brand, the Jeantet family went into negotiations with him, and resulting from that Jeantet was merged in the Cuty Fort Group (est. 1987 and headed by Chacom) in 1988 along with the pipe brands of John Lacroix and Emile Vuillard. Chacom closed the Jeantet plant, and the City of Saint-Claude purchased it in 1989. After alternative plans failed, the buildings were devoted to wrecking. The southerly workshop was wrecked before 1992.

Today Jeantet pipes were produced as a sub-brand by Chapuis-Comoy who’s mainstay is Chacom of course.

Jeff carefully cleaned up this Jeantet Brummer Painted Billiard with a Tortoise Shell stem with Murphy’s Oil Soap and a tooth brush to remove the grime on the rim top and bowl sides. He cleaned up the inside of the bowl with a Savinelli Fitsall Pipe Knife, scraping away the light cake on the bowl walls. He scrubbed the internals of the shank and stem with pipe cleaners, cotton swabs and alcohol until the airways were clean and the pipe smelled fresh. The pipe looked much better once the bowl and stem were clean. The plug in the slot of the stem was removed and the hole in the top was cleaned up as well. It was ready to repair when it arrived in Vancouver. I took photos of the pipe before I started my work on it. I took close up photos of the meer lined bowl and the rim top to show the condition. I also took photos of both sides of the stem to give a sense of the damage to the top side and the good condition of the underside.I took photos of the stamping on the left side of the shank and stem and the right side of the stem. It reads as noted above and is very clear and readable.I took the stem off the shank and took photos of the pipe to give a sense of its beauty and proportions.The bowl of the pipe was in excellent condition and did not need any work. The only major issue on the pipe was the hole in the top of the stem. I greased a pipe cleaner with Vaseline and slid it into the slot under the hole in the stem top. I filled in the hole with clear super glue. Once the glue cured it was a white spot that needed more work to blend into the stem surface. Once the repair cured I sanded the repair with 220 grit and polished it with 400 grit wet dry sandpaper. I polished out the tooth chatter on the underside of the stem with the same sandpaper and started polishing it.I used a dark brown and black stain pen to approximate the feathery wisps of the tortoise shell finish of the acrylic. I gave the repair a top coat of clear CA glue and let it cure. I sanded the spot smooth.I polished the stem surface with micromesh sanding pads. I wet sanded it with 1500-12000 grit sanding pads. I wiped the stem down after each pad with Obsidian Oil. I polished it with Before & After Stem Polish both Fine and Extra Fine polish. I gave it a final rub down with Obsidian Oil. I lightly buffed the bowl and stem with Blue Diamond on the buffing wheel and gave it a coat of Conservator’s Wax to seal and protect it. The pipe took on a deep shine in the painted briar and in the tortoise shell acrylic stem. The twin ring gold band also looked very good. It was an interesting looking pipe. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outer Diameter of the bowl: 1 ¼ inches, Diameter of the chamber: ¾ of an inch. The weight of the pipe is 60 grams/2.12 oz. The photos below show the finished pipe. It is a surprisingly nice looking pipe. If you would like to add it to your collection I will be adding it to the French Pipe Makers section of the rebornpipes store. Send me a message or an email. Thanks for reading the blog. It was an interesting restoration.

What a Beautifully Grained Proctus Deluxe Old Briar 71 Bent Egg/Brandy

This restoration is a bit of a resurrection of a beautiful Ferndown Root 3* Dublin

3 Replies

Blog by Steve Laug

This pipe was one of those happy coincidences. I have been looking for a Les Wood Hand Made Ferndown pipe for quite a while now to add to my collection. I have read a lot about them and had them on the wish list but have never found one. The crazy thing was that I was looking on Maxim Engels Site here in Canada and on EBay when I received an email from David asking if I would be willing to breath life back into this badly damaged beauty. That should have been an easy answer but I have been turning down work as my “day” job has dramatically become more consuming and I am left without a lot of time to work on pipes. I have been turning down pipes for repair for awhile now not wanting to add to the load. I postponed answering him and when I finally did I asked him to send me photos of the pipe so I would know what I was getting into. He immediately forwarded me the next two photos and I was hooked! I have not worked on a Ferndown before and this one looked like a good candidate for me to work on. I wrote and asked him about his timeline and he was very gracious with me. We struck a deal and the pipe was on its way to Canada for work. It dawned on me then that I had no idea what the rest of the pipe looked like and I would just have to wait and be surprised.I came home from my office yesterday to find the box from David waiting for me. My wife Irene had put it where I would see it. I took it to my work desk in the basement and carefully opened a well packed box that had originally contained pipes that I had sent to David. It was good to see this little box continue to serve its purpose as the vessel that protects it precious cargo. I took it out of the box and took some photos of it to chronicle the issues that I saw and give a benchmark for me before I began the work.

The pipe is a beautifully shape Dublin with a gold band. The pipe is stamped on the underside of the bowl and shank. On the heel of the bowl it is stamped Ferndown [arched over] Root [over] ***. Next to that it is stamped Hand Made In [over] England [over] Les Wood. On the gold band it is stamped L&JS in a rectangle [over] 9CT. The finish is quite beautiful but dirty on the bowl sides and shank. The largest issue with the pipe is the rim top and edges. There are burn marks around the front and back outer edges. The rim top itself is covered with lava but not enough to hide the charred inner edge and top. The damage is deep from the looks of the bowl top but cleaning would tell the story. The bowl itself is out of round from the damage. There was a thick cake in the bowl and the pipe stank of old tobacco but not enough to distinguish what it was… I know it was not an aromatic from the smell but otherwise I could not identify it. The taper stem is oxidized and has some calcification on the end. It is stamped on the left side and reads LJS. It was originally a stunning pipe and even with the damage and grime it still had class that was evident the moment you looked at it. I took a photo of the rim top and edges to show the burn damage around the bowl top and inner and outer edges. It has some serious char under the lava coat. The bowl is thickly caked as you can see from the photo. I also took photos of the stem to show its condition. There are light tooth marks and chatter on both sides next to the button and there is a deep oxidation in the vulcanite.I took a photo of the stamping on the heel of the bowl and underside of the shank and gold band. It is clear and readable as noted above.I removed the stem from the bowl and took a photo of the pipe to show the proportions of the design. It is really a well made pipe.I turned to Pipephil to help me interpret the stamping on the pipe and gain some background information (http://pipephil.eu/logos/en/logo-f1.html). The photo to the left shows Les Wood and the information below came from the side bar. I have also done a screen capture of the information on the site.

Artisan: Leslie (Les) Wood. He was the master silver smith at Alfred Dunhill Ltd. before starting L. & J.S. Briars. Pipes for the European market are stamped “L. Wood” while those for US are stamped “Ferndown”. Production: ~ 2000 pipes/year (Ferndown + L.Wood) See also Elwood.From the information on Pipephil I learned that I was working on a pipe made for the US and that it was a large 3 star pipe in terms of size. I also learned that the Root finish was a smooth light brown. All of which helped to understand the pipe in hand.

I turned to Pipedia (https://pipedia.org/wiki/Ferndown) to find a more detailed history and description of the brand and was amazed to find that the majority of it was either quotes or written by Les Wood himself. I am quoting some pertinent parts of the article below. You can turn to the site to read it in full.

Leslie “Les” John Wood worked for Dunhill for 19 years. His last position was as master silversmith. Following his tenure with Dunhill, Les formed his own brand, L. & J.S. Briars together with his wife Dolly in 1978. Les Wood follows Sasieni, the first ex Dunhill worker to start their own enterprise, and he was followed by William John “Ashton”-Taylor.

“I started working at Dunhill’s in March 1963, in the silver mounting department working under Jack Spriggs he left the firm after I had been there for 2 years, and I took over the department, at that time I worked alone it was only when the department was relocated to the top floor that the increase of pipes that needed mounting that we took on trainees. After 19 years I was asked if I would buy the machinery and move out of the factory and set up on my own, so off I went. With me I took the staff that worked with me at that time, Robert Morris was the best, he could mount anything, he now has his own jewellery retail shop and makes some really nice handmade jewellery from his shop at Whitstable in Kent.”

“I worked on Dunhill’s pipes from 1980/81 and soon built up a reputation as the firm to send your mounting to. As time went on and Dolly left Dunhill’s we decided to start to turn our own bowls and make our own pipes under the name of my house.” Les Wood. Jan, 2020…”

Due to the vagaries of international trademark law, he sold his earlier pipes as ” L.&J.S Briars”, “Ellwood”, “Les Wood” or “L. Wood”. Until recently, an average of 1500 – 2000 pipes a year were sold as “Ferndown” — named for the mansion he lives in — in the UK and US, but as “L. Wood” pipes in Germany…

To many pipe smokers, Les Wood’s pipes embody the revival of great English pipe making initiated by Ashton in the early 1980s. The high-grade Italian and Spanish plateau he prefers is oil-cured in the tradition of both Dunhill and Ashton. The pipes are renowned for their pleasant, slightly nutty flavor and remarkable smoking characteristics. They feature impeccable craftsmanship extending to very good stem/bit work, though many pipes are often a bit heavier. The hallmark of his work, of course, is the excellent silver work. Almost all of his pipes feature rings or ferules for spigot stems. Grading is by finish: “Bark” (ca. 90%, rusticated, dark brown and black), “Antique Bark” (tan rusticated), “Reo” (brown and red, smooth), “Root” (orange, smooth), and “Tudor Root” (orange and brown smooth) and by size (one to four stars). He also designates straight grains with SG…

“We bought the briar from Italy and Spain, one is mush denser that the other I like the Spanish briar it is lighter and Dolly would make the Roots look like glass with only a natural vanish, all the pipes were finished with the same varnish, the bark finish on the bowl is put on by Dolly by hand, one slip and you have a problem. That’s one job that needs to be seen to see how it’s done.”

There also was a great paragraph on the oil curing process that Les and Dolly developed. I am including that below as the pipe I am working on was definitely oil cured.

“We had our method of Oil-Curing. We applied Oil to the outside and the inside of the bowl, that was because when Dolly was at Dunhill’s factory, she worked in the finishing department and got such a high finish on the pipes they wanted to know how she did it. The bowls had already gone through Dunhills’ oven oil curing system, but to her, it was not enough, because it could not get the shine that she wanted, then, she oiled the bowl on the outside and the inside to get a better finished. She left Dunhill and came to work with me. Because of this process, we found out the smokers liked the taste when light up their pipe – they said there was no aftertaste and it had a sweet taste doesn’t matter what tobacco they used. We have carried it on from there.”

With that background information it was now time to work on the pipe itself. I decided to top the bowl to remove the heavy charring damage. I put a piece of 180 grit sandpaper on the topping board and worked the rim top and edges over in a circular motion on the board. After a few passes I took a photo of the rim top to show the progress but also to show the burn damage.Before working on the rim edges I reamed the bowl with a PipNet Reamer to cut back the cake to bare wood. I cleaned up the remaining cake with a Savinelli Fitsall Pipe Knife. I then sanded the bowl with a piece of 220 sandpaper wrapped around a piece of dowel to smooth out the bowl walls. The reaming and sanding cleaned up a lot of the damage on the inner edge as you can see in the fourth photo below.With that done I turned my attention to the inner and outer edges of the rim. I cleaned up both with a folded piece of 220 grit sandpaper. I worked on removing the burn marks on the outer edge and gave the inner edge a light bevel to hide the burn marks.I scrubbed the exterior of the bowl and shank with undiluted Murphy’s Oil Soap and a tooth brush. I work on the grime ground into the briar. I rinsed the bowl with warm running water to remove the debris left behind from the scrubbing. The pipe looked much better and the rim top was greatly improved. I cleaned the internals of the bowl, shank and airway in the stem with isopropyl alcohol, cotton swabs and pipe cleaners until they came out clean.I set the stem aside and turned my attention to polishing the briar. I used 1500-12000 grit micromesh sanding pads and wiped the bowl down after each pad with a damp cloth. The briar on the rim began to change the colour to get much closer to the rest of the bowl. I used a Maple stain pen to blend the rim top into the colour of the rest of the bowl. It matched well and served to obscure the burn mark on the rim edges. I also restained a light spot on the heel of the bowl. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The Balm did its magic and the grain stood out. I set the bowl aside and put the stem to soak in a bath of Briarville’s Pipe Stem Deoxidizer overnight. In the morning I rinsed it off with warm water and rubbed off the remaining softened oxidation until the stem was very clean. It looked very good and even the LJS gold stamping looked good. I set the bowl aside and turned my attention to the stem. I “painted” the tooth marks on the stem with the flame of a lighter to raise them. I sanded the remaining tooth chatter and marks with 220 grit sandpaper to blend them into the stem surface. I started the polishing process with 400 grit wet dry sandpaper. I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. The photo below shows the polished stem. I touched up the LJS stamp on the left side of the taper stem with Rub’n Buff Antique Gold. I rubbed it on and worked it into the stamp with a tooth pick. I buffed it off with a soft cloth. This nice looking Les Wood Ferndown Root 3 Dublin with a taper vulcanite stem is a great looking pipe now that it has been restored. The briar is clean and the grain really came alive. The rich brown stains gave the finish a sense of depth with the polishing and waxing. The grain really popped. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Ferndown Root 3 Dublin really is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 66 grams/2.36 oz. The pipe will be going back David very soon. I am looking forward to what he thinks once he has it back in his hands. Thanks for reading this blog and my reflections on the pipe while I worked on it. It was a fun one to work on.

Restoring a Kaywoodie “Standard” # 08 Straight Dublin From Steve’s Grab Box

Resurrecting What I think is an older Comoy’s Sandblast 43 Bent Billiard

1 Reply

Blog by Steve Laug

The next pipe on the work table came to us from a fellow in Brazil, Indiana, USA in March of 2020. The pipe is a classic looking Bent Billiard that has a deep and rugged sandblast. The pipe is stamped on the underside of the shank and reads Comoy’s [over] Sandblast followed by Made in London [over] England followed by the shape number 43. The stain is a mix of browns that contrasts well with the black of the hard rubber stem. The finish was very dirty with grime ground into the finish making it hard to see beyond that to the grain underneath. There was a thick cake in the bowl and it had overflowed with lava onto the rim top and edges. It was hard to know at this point the condition of the rim edges. The stem was made of hard rubber which pointed to an earlier date for the making of the stem. The stem had no stamping or identifying marks on it. Jeff took photos of the pipe before he started working on it. I include those below. He took photos of the rim top to show the thick cake and the thick lava coat on the edge and onto the top. It is hard to know what the condition of the rim top and edges is like under that thick lava. It is an incredibly dirty pipe but obviously one that was a great smoker. The stem has tooth marks and chatter on both sides ahead of the button. It also has some residue left behind by a rubber Softee Bit. He took photos of the sides and heel of the bowl to show the beautiful sandblasted grain around the bowl and the condition of the pipe. You can see the grime ground into the surface of the briar. He took photos of the stamping on the underside of the shank. It is clear and readable as noted above. Jeff took a photo of the underside of the shank showing a shrunken fill with a crack in it. Fortunately it was not in the briar but in the fill itself. I turned to Pipedia (https://pipedia.org/wiki/Comoy%27s) and reread the great history of the brand and found an advertizement for the Sandblast line. I include that advert below.I turned to the listing on the site that gave shape numbers and a description of the various shapes in chart form (https://pipedia.org/index.php?title=Comoy%27s_Shape_Number_Chart). I found the shape number 43 which was on this pipe. It is described in the chart below as a ½ Bent Billiard in a large size. That is a perfect description of the pipe I am working on.It was time to work on the pipe. As usual Jeff had done a thorough cleanup on the pipe. He reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils and tars on the rim and the grime on the finish of the bowl. He rinsed it under running water. He dried it off with a soft cloth. He cleaned the internals and externals of the stem with alcohol, pipe cleaners and cotton swabs. He soaked the stem in Briarville’s Pipe Stem Deoxidizer and rinsed it off with warm water and cleaned out the airway in the stem with alcohol. This Bent Billiard pipe actually was quite stunning! I took a photo of the rim top and stem to show the condition. The rim top and edges looked very good. The hard rubber stem had tooth chatter and marks on both sides ahead of the button and on the button edges. There was one deeper large one on the underside of the stem. I removed the stem and took a photo of the pipe to give a sense of the whole. It is a nice looking pipe that should clean up very well. I decided to address the crack in the fill on the underside of the shank first. I filled it in with clear CA glue and once it cured I smooth out the repair with 1500-2400 micromesh sanding pads. It looked much better once it was finished. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The Balm did its magic and the grain stood out. I set the bowl aside and turned my attention to the stem. I “painted” the tooth marks on the stem with the flame of a lighter to raise them. I filled in the remaining tooth marks with clear CA glue and set it aside until the repairs cured. I used a small file to flatten the repair and recut the edge of the button. I sanded the repaired areas with 220 grit sandpaper to blend them into the stem surface and also worked on the remaining oxidation at the shank junction. I started the polishing process with 400 grit wet dry sandpaper. I polished the hard rubber stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. The photo below shows the polished stem. This nice looking older Comoy’s Sandblast 43 Bent Billiard with a hard rubber taper stem is a great looking pipe now that it has been restored. The briar is clean and the blast really came alive. The rich brown and black stains gave the blast a sense of depth with the polishing and waxing. The grain really popped. I put the hard rubber stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Comoy’s Sandblast Bent Billiard really is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 54 grams/1.90 oz. The pipe will be going on the rebornpipes store soon. It will be in the section on British Pipe Makes if you would like to add it to your collection.Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

A Simple Restoration Of An Inherited BBB “Thorneycroft” # 637 Sandblast Billiard

This was a Stunning Butz-Choquin Camargue 1025 Rhodesian once it came back to life

1 Reply

Blog by Steve Laug

The next pipe on the work table came to us from an antique mall in Logan, Utah, USA early in 2021. The pipe is a classic looking Butz-Choquin that has a marbleized acrylic shank extension. The pipe is stamped on the sides of the shank. On the left side of the shank it reads Butz-Choquin [over] Camargue and on the right side it reads St. Claude [arched over] France [over] the shape number 1025. The stain is a mix of browns that contrasts well with the marble like shank extension. The finish was very dirty with grime ground into the finish making it hard to see beyond that to the grain underneath. There was a thick cake in the bowl and it had overflowed with lava onto the rim top and edges. It was hard to know at this point the condition of the rim edges. The stem was vulcanite and was a military mount fish tail stem. The stem had no stamping or identifying marks on it. Jeff took photos of the pipe before he started working on it. I include those below. He took photos of the rim top to show the thick cake and the thick lava coat on the beveled edge and onto the top. It is hard to know what the condition of the rim top and edges is like under that thick lava. It is an incredibly dirty pipe but obviously one that was a great smoker. The shank extension looks good and is acrylic. The stem has tooth marks and chatter on both sides ahead of the button. He took photos of the sides and heel of the bowl to show the beautiful grain around the bowl and the condition of the pipe. You can see the grime ground into the surface of the briar. He took a photo of the stamping on the sides of the shank. It is clear and readable as noted above. He also captured the BC stamp on the shank extension. The shank extension was loose on the shank and had come unglued. It was filthy and the glue was dried and the extension came off. Jeff took photos of the parts. I remembered that I had worked on a Camargue pipe by Butz-Choquin before so I turned to the blog and did a search (https://rebornpipes.com/2020/10/24/fresh-life-for-a-butz-choquin-camargue-bent-rhodesian-sitter/). I quote from that blog and also from one that Dal Stanton wrote.

Dal Stanton had written a blog on his restoration of a Camargue pipe for rebornpipes in the past (https://rebornpipes.com/2019/12/04/rejuvenating-a-fancy-french-butz-choquin-camargue-1683-prince/). I turned to that now for a quick review of the history of the line. I quote:

I’ve worked on several Butz Choquin pipes which is based in the French pipe center of St. Claude. Here is a brief overview of the BC history from http://www.pipephil.eu/logos/en/logo-butzchoquin.html

The origin of the brand reaches back to 1858 when Jean-Baptiste Choquin in collaboration with his son-in-law Gustave Butz created their first pipe in Metz (France). Since 1951 Butz-Choquin Site officiel Butz Choquin, pipes de Saint-Claude Jura. BC pipe de bruyere luxe is a brand of the Berrod-Regad group (Saint-Claude, France).

Jean Paul Berrod managed the company from 1969 to 2002 when he retired and sold the corporate to Mr Fabien Gichon. Denis Blanc, already owner of EWA, took over the S.A. Berrod-Regad in 2006.

The BC line, ‘Camargue’ is not an old line as a simple search on the internet turns up several examples of classic pipe shapes with the ‘Camargue’ stamp, but unique to each is the acrylic shank extension and the military mounted stem. This example is a Dublin shape from (https://www.smokingpipes.com/pipes/estate/france/moreinfo.cfm?product_id=189826).Dal had also done some research on the name Camargue that I have included below. For me this kind of information adds colour to the restoration that I am working on.

…The name of the line, ‘Camargue,’ I discovered is a treasured nature reserve on the southern coast of France between Montpellier and Marseille – two beautiful venues which I’ve had the opportunity to visit. A Wiki article was very helpful in describing the area that this BC line is commemorating (https://en.wikipedia.org/wiki/Camargue).

With an area of over 930 km2 (360 sq mi), the Camargue is western Europe’s largest river delta. It is a vast plain comprising large brine lagoons or étangs, cut off from the sea by sandbars and encircled by reed-covered marshes. These are in turn surrounded by a large cultivated area.
Approximately a third of the Camargue is either lakes or marshland. The central area around the shoreline of the Étang de Vaccarès has been protected as a regional park since 1927, in recognition of its great importance as a haven for wild birds. In 2008, it was incorporated into the larger Parc naturel régional de Camargue.

The Camargue is home to more than 400 species of birds and has been identified as an Important Bird Area (IBA) by BirdLife International.[8] Its brine ponds provide one of the few European habitats for the greater flamingo. The marshes are also a prime habitat for many species of insects, notably (and notoriously) some of the most ferocious mosquitos to be found anywhere in France. Camargue horses (Camarguais) roam the extensive marshlands, along with Camargue cattle (see below).

The native flora of the Camargue have adapted to the saline conditions. Sea lavender and glasswort flourish, along with tamarisks and reeds…It was time to work on the pipe. As usual Jeff had done a thorough cleanup on the pipe. He reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils and tars on the rim and the grime on the finish of the bowl. He rinsed it under running water. One of the benefits of this scrub is that it also tends to lift some of the scratches and nicks in the surface of the briar. He dried it off with a soft cloth. He cleaned the internals and externals of the stem with alcohol, pipe cleaners and cotton swabs. He soaked the stem in Briarville’s Pipe Stem Deoxidizer and rinsed it off with warm water and cleaned out the airway in the stem with alcohol. This Rhodesian pipe actually was quite stunning! I took a photo of the rim top and stem to show the condition. The rim top looked very good. There was some darkening on the rim top and the inner edge of the bowl. The loose shank extension would need to be aligned and glued. The vulcanite stem had light tooth chatter and marks on both sides ahead of the button and on the button edges. I removed the stem and the extension from the shank and took a photo of the pipe to give a sense of the whole. It is a nice looking pipe that should clean up very well. I aligned the extension in the shank and glued it in place with clear CA glue. I polished the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiped down the bowl after each sanding pad. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips. I worked it into the twin rings around the bowl cap with a horsehair shoe brush. The product works to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The Balm did its magic and the grain stood out. I set the bowl aside and turned my attention to the stem. I sanded the tooth chatter and marks with 220 grit sandpaper and started the polishing process with 400 grit wet dry sandpaper. I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. The photo below shows the polished stem. This nicely grained Butz Choquin Camargue 1025 Rhodesian with a vulcanite military bit stem is a great looking pipe now that it has been restored. The briar is clean and really came alive. The rich brown stains gave the grain a sense of depth with the polishing and waxing. The grain really popped. I put the vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Butz Choquin Camargue Rhodesian is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 50 grams/1.76 oz. The pipe will be going on the rebornpipes store soon. It will be in the section on French Pipe Makes if you would like to add it to your collection.Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!