Tag Archives: shaping a stem

Fresh Life for a Comoy’s The Everyman 126 Sandblast Pot

2 Replies

Blog by Steve Laug

The next pipe on the work table is another pipe that came to me from the estate of a Vancouver pipe smoker whose widow left them with a local Pipe Shop after he died. I was asked to clean them up and sell them for the shop as it has since closed. The photos below show the pipe as it was when I brought it to my work table. It is a nicely shaped sandblast pot shaped pipe – with a a really nice looking grain pattern in the blast under all the grime. The bowl was heavily caked with a lava coat on the top of the rim. It was hard to tell how the inner and outer edge of the rim actually looked until the bowl was reamed. The bowl was dirty and the finish was almost filled in with the grime. The stem had the same deep tooth marks and chatter on the top and underside near the button as the rest of the pipes in this estate. There was calcification on the first inch from what looked like a Softee bit. From the three bars on the left side of the stem and the stamping it was clearly a Comoy’s product. In this case it was stamped on a smooth band on the bottom of the bowl and shank with the words The Everyman London Pipe. Next to that it is stamped Made in London England followed by the 126 shape number next to the shank/stem junction. I took photos of it before cleaning to show that even though it was dirty the pipe showed promise.   When I went back to the States after Christmas to visit my parents and brothers I took a box of these pipes with me so that I could have Jeff clean them for me. When they came back to Canada they looked like different pipes. He reamed the bowl with a PipNet pipe reamer and cleaned it up with a Savinelli Fitsall Pipe Knife. He scrubbed the exterior with Murphy’s Oil Soap and a tooth brush to clean off the grime on the finish and the heavy overflow of lava on the rim top. He cleaned up the internals of the shank, mortise and stem with pipe cleaners, cotton swabs and alcohol to remove all of the oils and tars in the pipe. When it came back to Vancouver it was a quite different pipe. I took photos of it before I started the restoration. I took photos of the rim top and the stem to show their condition. Jeff was able to clean out the bowl completely and the rim top. He removed the tars and lava and left behind a clean top that would need some stain touch ups. The stem was oxidized, though less so where the Softee bit had been. There were scratches, tooth chatter and marks on both sides near the button and on the surface edges of the button itself.I decided to work on five of the pipes from this estate at the same time so I put all of the stems in a bath of Before & After Pipe Stem Deoxidizer to soak. I submerged all of the stems in the bath and let them soak overnight to break down the oxidation.I took all of the stems out of the bath at the same time and rinsed them under warm water to rinse off the mixture. I blew air through the stems and ran water through them as well to rinse out the mixture there as well. Each of the stems still had varying degrees of oxidation but it was all on the surface of the stems. The photos below show the Everyman stem after rinsing and drying.I painted the surface of the stem with the flame of a Bic lighter to lift the tooth marks. One of the benefits of the lighter is that it burned off the sulfur on the surface of the stem. The top side of the stem came out very well as the tooth chatter and marks lifted. A little sanding would smooth it out well. On the underside it was a bit less successful. There were still two deep tooth marks present that would need to be repaired.I filled in the tooth marks and the dents on the top and bottom sharp edges of the button to smooth things out using clear super glue. Once the repair cures, I will sand it smooth and blend it into the surface on each side.While the repair was curing I turned my attention to the bowl. I touched up the faded areas on the rim top and around the sides of the bowl and shank with a Walnut stain touch up pen. It blended in very well with the colour of the rest of the bowl. The bowl had a hollow spot below the entrance of the airway. It was as if the bowl had been reamed with a knife and damage had been done to the bottom of the bowl. It was quite deep and rough. Since it was below the entrance of the airway I mixed a batch of JB Weld to apply to the deep gouge and build up the bottom of the bowl to the same height as the airhole. I applied it with a dental spatula and pressed it into the bottom of the bowl with a piece of wooden dowel. I rubbed down the briar with Before & After Restoration Balm. I worked it into the nooks and crannies of the sandblast finish to clean, enliven and protect the new finish. It also evened out the stain coat and gave the stain a multidimensional feel. I let the balm sit for a little while and then buffed it with a horsehair shoe brush. I buffed the bowl with a cotton cloth to raise the shine. At this point the bowl is pretty well finished. I still need to wax and buff it but that will wait for the stem. The repair on the stem had cured so I turned back to work on the stem. I used a file to recut the sharp edge of the button and then sanded it with 220 grit sandpaper until I had blended the repairs into the surface of the stem. I also worked on the remaining oxidation with the sandpaper until I removed that as well.I polished out the scratches in the vulcanite with 400 grit wet dry sandpaper and with micromesh sanding pads. I wet sanded with 1500-2400 grit pads and dry sanded with 3200-12000 grit pads. I wiped the stem down after each pad with Obsidian Oil. After sanding with the 12000 grit pad I polished the stem with Before & After Pipe Stem Polish – both Fine and Extra Fine. With the stem polished I put it back on the pipe and lightly buffed the bowl with Blue Diamond. I buffed the stem with a more aggressive buff of Blue Diamond. I gave the bowl several coats of Conservator’s Wax and the stem several coats of carnauba wax and buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The finished pipe is shown in the photos below. I will be posting it on the rebornpipes store very soon. It should make a nice addition to your pipe rack if you have been looking for a reasonably priced Comoy’s The Everyman Pipe. The sandblast finish looks really good in person with depth and texture. It should be a great smoking pipe with a good hand feel. The dimensions are Length: 5 1/2 inches, Height: 1 1/2 inches, Outside diameter of the bowl: 1 1/2 inches, Chamber diameter: 7/8 inches. Thanks for walking through the restoration with me as I worked over this estate Comoy’s.

 

Restoring a Tired House of Robertson Billiard

Leave a reply

Blog by Steve Laug

Not too long ago I sold one of the House of Robertson pipes to a fellow named John who collects them and lives in Salt Lake City, Utah. He loved the pipe that I sent him and wrote and asked if I would be willing to clean up and restore his first House of Robertson (HOR) pipe that had been given to him 30+ years ago by his brother. He said it was a billiard with a mixed finish – both rusticated and smooth. He said he had smoked it heavily as it was a favourite of his and it needed some attention. We made our arrangements and he shipped the pipe to me here in Vancouver. I was looking forward to working on it as I have enjoyed the other House of Robertson pipes that I have restored over the past months.

While I waited for its arrival, between working on other pipes I read over the last restoration blog I had written on an HOR pipe. I thought it might be helpful to add the information I had previously found for those of you who have not read those blogs. “House of Robertson” was in business for many years, but alas, closed their doors in 1999. They were located in Boise, Idaho. They are noted for making rather large and interesting pipes. Thayne Robertson… started the shop about 1947 and his son Jon started working there in 1970 when he finished college, along with Thayne’s daughter. Thayne and his son started making the big pipes at that time, and made them together until 1987 when Thayne passed away. Jon kept the store and his sister moved on to other things. The House of Robertson appears to have closed around 1999. https://pipedia.org/wiki/Robertson

I also received an email from Ed Mitchell from the Boise, Idaho area offering to share some of the history of the shop if I was interested. He was a frequent customer and loves the HOR Pipes. I of course was excited to learn more about the brand so I was looking forward to what he would write. It came in today’s email and I thought you might enjoy Ed’s reminiscences. Thanks Ed for sending me this information.

Hi, Steve

…I do not have any memorabilia, other than a box of two, from the House of Robertson shop. When Jon Robertson closed the store, it caught me by surprise. I do have several of Robertson pipes including a couple that need small repairs. Five or six I bought unsmoked from the widow of one of his Boise customers. The husband apparently was one of Thayne’s many friends and had bought pipes in the course of standing around visiting in his shop. One is a beautiful blond horn that I have saved unsmoked.

Thayne was a bear of a man in his 60s when I met him in the mid-1960s, a great raconteur with strong opinions on politics, religion, people and good pipes. For instance, he hated cigarette smoking; people who popped in to ask for cigarettes were shown the door with instructions on how to find the only other tobacco store in downtown Boise, an institution (still in business) that sold all types of tobacco, men’s magazines and pipes Thayne considered unworthy of any discerning smoker.

Another consequence of Thayne’s hatred of cigarettes was that he created a line of pipes sized and decorated (in some examples with inset bits of bling) for female smokers. He did make pipes in conventional shapes and sizes but preferred big freestyles. I can say I do not remember his ever making two pipes exactly alike. A large part of his business involved creating custom pipes on order. He mailed pipes to customers around the country and internationally. I am not sure what portion of his output was sold outside Boise but I had the impression that it was considerable.

The pipes I remember Thayne smoking in the shop were a couple of huge Oom Pauls about a foot long. The big man liked big pipes, usually loaded with strong English-style or oriental blends. He hooked me on my taste for Latakia tobaccos.

The shop was in one of the long, narrow brick storefronts of the old city core. An old-fashioned glass display case for pipes and accessories dominated the front along with shelves and stacks of at least 50 choices of tobaccos. A narrow flight of stairs led to inventory storage above the dusty workshop located in back behind a curtain.

For a one man shop, Thayne’s output was prodigious especially considering that the individual pipes were unique. His daughter Rosie and son Jon did assist in the shop’s latter years. Both were skilled makers but tended to create more conventionally carved and sized pipes. Most of the pipes made there, even after Thayne died and Jon was doing the work, came from a hoard of old Greek briar Thayne found in Holland around 1970. Some of the bold grain pipes from the latter years were as spectacular as smoking instruments can be. One feature I have never seen is a fill in a Robertson pipe. Thayne liked rusticating briar whenever the grain was flawed or just uninteresting.

Steve, I hope this gives you some brief insight into the House of Robertson. If you have questions to stimulate my ancient memory, I will be glad to try to answer. — Ed Mitchell

When the pipe arrived I took it out of the box to have a look at it and took some photos of it to show its condition before I began. It had a softee bit on the stem that had slid up about ¼ inch up the stem from the button. The finish was dirty and grimy. The rim top was damaged and the bowl was slightly out of round. There was a thick cake in the bowl and a heavy lava overflow on the top of the rim. There was a burn mark that was on the top of the rim at the front and extended down the bowl about a ½ inch. There was a nickel band on the shank that was a typical repair band that is available through repair suppliers. When I examined around the band on the shank end I could not see any cracks in the shank. The band had been cut off slightly so as not to cover the etched House of Robertson name on the left side of the shank. The stem was an obvious replacement that was slightly larger in diameter than the shank. The pipe definitely needed attention. I took a close up photo of the rim top to show the damage to the front of the bowl and the general condition of the pipe. The bowl is thickly caked and the rim has an overflow of lava on the rim top.  You can see how the bowl is thicker on one side than the other. The front of the bowl looks damaged as the lava on that portion is different in texture than the hard stuff on the rest of the rim top. The stem was in decent condition – some calcification on the top and underside where the rubber softee bit had been. There were some light tooth marks and chatter on both sides. The stem was lightly oxidized.I did a quick assessment of the pipe and wrote John a quick email about what I saw as I looked it over. I sent my questions to him to see if he could shed any light on what I was seeing. I am including both my questions and his response as it helps clarify what I saw when I examined the pipe first hand.

  1. Is the band something that you added? It appears to be cosmetic but it could be a repair band. They are available through online pipe parts guys and are made out of nickel. I think it is a later addition as it covers the N in Robertson. Do you know if the shank was ever cracked?? I will leave it there as it is a touch of bling.
  2. Is the stem a replacement stem? It is wider is in diameter than the shank and appears to be a replacement. The shank was drilled for a filter stem and this one is not the original as far as I can tell. It is well made and will clean up nicely. I took the softee bit off and will clean it up. I will send the softee back with the pipe.
  3. What is the hard substance in the bottom of the bowl? It appears that someone added some fill to the bottom of the bowl (unevenly mind you) to lift the bowl bottom to the level of the entry of the airway into the bowl. Is this something you added or was it there previously? I can leave it be as it is as hard as concrete. I can also smooth it out a bit with a coat of JB Weld (which is what I think is in the bottom of the bowl already).

John replied to my queries and I am including the pertinent parts of his answers:

To my recollection, the pipe is the same un-worked-on one my little brother gave me 38 or so years ago, bought directly from Mr. Robertson at his shop — I’m assuming it was the father and not the son, but I can’t remember when the elder died.

I may have had it worked on — possibly a new stem — at Jeannie’s Smoke Shop (now sold to newcomers since my friend Jeannie died; the shop still retains the name) in Salt Lake City. I do remember taking it, or possibly another pipe, to the craftsman she employed. If that was the pipe I took in, I don’t think he would have filled the bottom of the bowl, but he may have replaced the stem. I smoked that pipe a lot years ago and may have bit the mouth piece off. If you don’t think the current stem is one that Robertson used and feel strongly that it should be changed out with new, proper stem, do it. But you indicate that the stem is fine and you can touch it up and smooth it out, that’s fine, too. Your decision. And do what you suggested with smoothing the bottom of the bowl and adding the JB Weld coat. I have no idea why that would have been filled in.

I don’t recall adding a band. I don’t recall if the shank was cracked years ago and that I may have asked the guy at Jeannie’s to fix that. Please do whatever you need to do with that part. A few weeks ago, I thought I detected a slight crack, or maybe just a dark line along the shank. You don’t seem to think that a new band is necessary. The last Robinson you sold me has a silver band; my other two do not have bands. But I am reasonably sure the nickel band is what Robertson had on it when he sold it to my younger brother ($50 at the time! — a lot of money for a 19-year-old’s gift to his older brother). Possibly the stem got damaged when Robertson was making the pipe, and that’s the way he fixed it…

I reamed the bowl with a PipNet pipe reamer – starting with the smallest cutting head and working up to the third one. I cleaned up the remnants with a Savinelli Fitsall Pipe Knife. Surprisingly there was a rock hard substance at the bottom of the bowl – it looked like JB Weld or something like that. It was rock hard and seemed to have been used to bring the bottom of the bowl up to the bottom of the airway’s entrance to the bowl.I scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush. I worked over the rim top with a brass bristle wire brush to break up the lava flow there. I rinsed the bowl with running water and scrubbed it under the water while it was rinsing. The bowl began to look pretty good at this point. The contrast between the smooth band around the bowl and shank with the rustication above and below the band looked really good. The rim top was so damaged with the burn mark and the nicks around the outer edge that I decided to top the bowl lightly to remove as much of the damage as I could without noticeably changing the profile of the pipe. I worked on the inner edge of the rim and the light bevel with 220 grit sandpaper to clean up the inner edge. I used it to also lightly reshape the outer edge of the bowl. You can see from the photos how out of round the bowl edges are outside and inside. I worked on the bevel to work on it and you can see the result in the third photo.I did not want to add stain to the oil finished bowl so I just rubbed the bowl down with Before & After Restoration Balm to deep clean the rustication on the briar. The rustication was well done and looked almost like a sandblast. I also rubbed it into the smooth portions on the band around the bowl, the rim top and the shank. The product works to clean, enliven and protect the briar. I hand rubbed it with my fingers to work it into the rustication. I wiped it off with a soft cloth. I buffed the bowl with a horsehair shoe brush to polish it. The briar really began to have a rich shine. I took some photos of the bowl at this point to mark the progress in the restoration. I decided to polish the topped rim top once more using micromesh sanding pads as the balm revealed more scratches in the finish. I wet sanded it with 1500-2400 grit pads and dry sanded it with 3200-12000 grit pads. I wiped it down after each pad with a damp cloth. I cleaned out the internals of the mortise and the airway in the shank and the stem with pipe cleaners, cotton swabs and alcohol. (I forgot to take photos of the stem after I cleaned it with alcohol and pipe cleaners).I mixed up a small batch of JB Weld to level the previous repair to the bottom of the bowl. I applied it to the uneven area with the end of a small sanding stick. I pressed it into the indentation and smoothed it out with the tip of my finger.I set the bowl aside and worked on the stem. I sanded out the tooth chatter, tooth marks and oxidation on the button end. I sanded the rest of the stem to remove the oxidation. The diameter of the stem was bigger than that of the shank so I sanded that at the same time to reduce it to the same size as the shank and reshape it at the junction. I polished the stem with micromesh sanding pads – wet sanding it with 1500-2400 grit pads to remove the scratching. I worked on it until the stem surface was smooth and the marks were less visible. I continued to polish it with 3200-12000 grit sanding pads. I wiped it down with Obsidian Oil after each sanding pad. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I wiped it down a final time with Obsidian Oil. I put the stem back on the bowl and worked the pipe over on the buffing wheel using Blue Diamond to lightly polish both the bowl and the stem. I buffed the bowl and stem to raise the gloss on the briar and the vulcanite. I gave the pipe multiple coats of carnauba wax. I buffed the entire pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The finished pipe is shown in the photos below. I don’t think House of Robertson stained the pipes as they have the rich patina of an oil finish. If it had a stain coat it was a tan stain that went well with the rich black of the vulcanite stem. The dimensions of the pipe are: Length: 5 1/2 inches, Height: 1 3/4 inches, Outside Diameter: 1 3/8 inches, Diameter of the chamber: 7/8 inches. This is an interesting piece of briar that shows a mixture of grain on the smooth portions. I really like HOR pipe work the rustication and smooth parts together in unique ways. Once the repair in the bowl cures I will mail it back to John. I know he is looking forward to enjoying it again. Thanks for walking with me through the restoration.

Restoring a Savinelli Churchwarden 3003

1 Reply

Blog by Steve Laug

I finished the restoration work on Mark’s uncle’s pipes and a few of his own and sent them back to him in late January of this year. I wrote a blog on each of the restorations. They were a fun batch of pipes to restore for him. He sent me another package a few weeks ago that had just three pipes in it – A GBD Classic Straight Bulldog, a GBD 9242 Rhodesian (one of my holy grail pipes) and a long Churchwarden pipe that had originally belonged to his uncle. Each pipe had a different set of issues that would provide a variety of challenges. The Bulldog was in excellent condition other than the first ½ inch of the stem missing in chunks. The Churchwarden had a broken tenon that was still stuck in the shank. By far the worst of the lot was the 9242 pipe. When I saw it in the bag I was excited. When I took it out of the bag I was saddened at the condition of the pipe. The bowl was dirty and there was some lava and rim darkening on the top. There were a few nicks in the edges of the bowl. The finish was dirty but the grain on the pipe was really nice. If I had stopped my observation at this point I would have been quite happy.

The second pipe I chose to work on from the batch of pipes was the Churchwarden that had belonged to his uncle. The Prince shaped bowl was in decent condition. The bowl was actually quite clean on the inside but the drilling where the airway entered the bowl was slightly off to the right side of the bowl. Other than having the tenon stuck in it; the shank looked pretty good as well. The rim top was dirty and there was a burn mark on the inner bevel of the left side. The finish was dirty and there were quite a few nicks and dents on the surface of the briar. The shank was stamped on the left side with the words Churchwarden over Aged Briar. On the right side of the shank it is stamped with the shape number 3003 and next to that was the Savinelli S shield. The underside of the shank is stamped Savinelli over Italy. The stem was quite oxidized and pitted. There were tooth marks and chatter on both sides of the stem at the button. The broken tenon remnants were on the end of the stem. It was broken pretty close to the stem/shank junction.

Sooo… here we go on the second of Mark’s restoration projects. I took photos of the pipe to show what it looked like when it arrived in all of its tattered splendour. The bowl had some beautiful grain underneath the grime. The photos show the stem the broken tenon and how close to the shank it was snapped off. The above photo shows the damage on the rim top to the inner edge. It is a burn mark from repeated lighting of the pipe in that spot. The photos below show the chatter and tooth marks on both sides of the stem at the button.The broken tenon was stuck in the shank when I first tried to pull it so I put it in the freezer for 30 minutes. I tried again using a long drywall screw and was able to get it free with the first try. I went through my jar of replacement tenons and found one that I thought would work. It is a threaded Delrin replacement tenon. Once I had the broken tenon out of the shank I compared them and found that the diameter was the same on both.  I tried it in the mortise and found that it was a perfect fit. Even the length was correct. I flattened the broken pieces on the end of the stem with a Dremel and sanding drum and then on the topping board. I wanted a flush surface to mount the new tenon on and also to have a snug fit against the shank. The airway was not centered in the stem so I had to do a bit of fussing with it to get it ready for the new tenon. I used a sharp pen knife to flare the side of the airway that was off to get it more centered before I drilled. Once I had done that I drilled the airway with a bit slightly larger in diameter than the airway and worked to keep it both straight and centered. This is yet another time I wished I had a drill press.I followed that drill bit with one that was the same diameter as the threaded portion of the new tenon. I sanded the threads to slightly reduce the diameter and pressed it into the stem. The fit was very good. I took a photo of the stem  at this point to show the look of the new tenon.I used black super glue that had a medium viscosity so that I had time to align the stem and the shank before the glue set. Once it was aligned I took a few photos of the fit of the stem to the shank. I would need to make a few minor adjustments but considering how off the airway was the fit was quite good. I carefully removed the stem and set it aside to let the glue on the tenon set firmly. I turned my attention to the bowl. The first item of business for me was to work on the rim top. I cleaned up the flat surface of the rim with 1500-2400 micromesh sanding pads and then shaped the inner bevel of the rim with a folded piece of 220 grit sandpaper to minimize the damage on the right inner edge. When I finished it definitely looked better. I would do a bit of finessing it once I worked on it with the micromesh pads.I decided to address the many nicks, scratches and cuts in the surface of the finish by filling them in with clear super glue. The next series of photos show the many spots on the front and bottom of the bowl.Once the repairs had dried I sanded them smooth with 220 grit sandpaper to blend them in with the surface of the bowl. I then wet sanded the entire bowl and rim with 1500-2400 grit micromesh pads and dry sanded it with 3200-12000 grit pads until the rim and the surface of the bowl was smooth and polished. I wiped down the surface of the bowl with a damp cloth to remove the sanding dust between each pad. I decided to highlight the reds in the briar and finish so I stained it with a mahogany stain pen. It looks streaked and poorly applied in the photos but the story is not over yet. I am more interested in getting the bowl covered with a stain that is transparent so when I take the next step the grain will come through the finish. Of course I was in a hurry at this point to call it a night so I forgot to take pictures of the next step. I wiped the bowl down with a cotton pad and isopropyl alcohol to spread the stain and wipe away the excess. When the grain stood out and the repairs remained hidden I rubbed the bowl down with Before & After Restoration Balm. I rubbed it into the finish to clean, enliven and protect the finish. I let it sit for a few moments and buffed it off with a cotton cloth. The photos below show the bowl at this point. Once the bowl was finished I set it aside to work on the stem. I sanded out the tooth marks and chatter on the top and underside of the stem at the button. I sanded the entire stem with 220 grit sandpaper to remove the damage and oxidation.I polished the vulcanite with micromesh sanding pads to remove the scratching and remaining oxidation. I wet sanded it with 1500-2400 grit pads and dry sanded it with 3200-12000 grit pads. I wiped the stem down with Obsidian Oil after each pad to remove the dust. I finished polishing the stem with Before & After Pipe Stem Polish – both Fine and Extra Fine to remove the rest of the scratches in the hard rubber surface. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel. I gave it several coats of carnauba wax and buffed it with a clean buffing pad to raise a shine. I hand buffed it with a microfiber cloth to deepen the shine. The finished pipe is shown in the photos below. The repairs on the finish blend in really well with the overall finish of the pipe. The new tenon on the stem works very well and is a snug fit in the mortise. It really is a nice looking Savinelli Churchwarden. There is some nice grain on the bowl. This is the last of Mark’s uncle’s pipes and it is ready to head back to Mark for his smoking pleasure. I have one more pipe to fix for him then this one and the others will be in the post back to Mark. I think it is better than it was… thanks for looking.

 

New Life for an Italian Made Harvey Futura Billiard

2 Replies

Blog by Steve Laug

The next pipe on the work table is another pipe that came to me from the estate of a Vancouver pipe smoker whose widow left them with a local Pipe Shop after he died. I was asked to clean them up and sell them for the shop as it has since closed. The photos below show the pipe as it was when I brought it to my work table. It is a nicely shaped billiard – with a swirling grain all around the bowl and shank. The unusual patterns of the grain on the briar is unique and a bit captivating. The bowl was heavily caked with a lava coat on the top of the rim. It was hard to tell how the inner and outer edge of the rim actually looked until the bowl was reamed. The bowl was dirty but the finish was still shiny as if it had a top coat of varnish or shellac over the stain coat. The stem had some tooth chatter and marks on the top and underside near the button. The push tenon was quite long and stepped down. The pipe had promise it was very dirty. Since it was an Italian Made Pipe I did a bit of research to see if I could find it on the web. I checked on the PipePhil website and it was not listed there. I also check on Pipedia and found a listing under Italian made pipes that read Harvey pipes but gave absolutely no information on the brand. I have a theory that the brand was made by Rossi because I knew that the factory made many pipes for various sellers around the world. I have no proof of it of course but it is a good possibility. I have no idea of the connection between Rossi and Harvey pipes but I sense that there is one.

I took photos of the stamping on the shank to show the stamping around the sides and bottom of the shank. The top two photos show the left side of the shank which is stamped HARVEY over Selected Grain over FUTURA. Both photos show the same stamping with the angle slightly different to give a clear idea. The third photo shows the Made in Italy stamp on the right side of the shank. The fourth photo shows a number stamped on the underside of the shank. It reads 25-853.When I went back to the States after Christmas to visit my parents and brothers I took a box of these pipes to Jeff to clean up for me. He reamed this Harvey Italian Made Billiard with a PipNet pipe reamer and cleaned it up with a Savinelli Fitsall Pipe Knife. He scrubbed the exterior with Murphy’s Oil Soap and a tooth brush to clean off the grime on the finish and the heavy overflow of lava on the rim top. He cleaned up the internals of the shank, mortise and stem with pipe cleaners, cotton swabs and alcohol to remove all of the oils and tars in the pipe. When it came back to Vancouver it was a quite different pipe. I took photos of it before I started the restoration. I took photos of the rim top and the stem to show their condition. Jeff was able to clean out the bowl completely and the rim top. He removed the tars and lava to reveal some peeling of the varnish coat on the rim and some very obvious fills that can be seen in the first photo. The stem was oxidized and pitted. There were scratches, tooth chatter and marks on both sides near the button.I am working on five of the pipes from that estate at the same time. I put all of the stems in a bath of Before & After Pipe Stem Deoxidizer to soak. I submerged them all of the stems in the bath and let them soak overnight to break down the oxidation.While the stem soaked I worked on the rim top with 400 grit wet dry sandpaper to remove the peeling varnish and clean up the filled areas. I wiped it down with a damp cloth and dried it off. I repaired the damaged fills with clear super glue being careful to keep the glue in the filled areas alone. Once the glue cured I sanded down the repaired fills with the corner of a filled piece of 220 grit sandpaper to blend them into the surface of the rim. Once it was smooth I polished the rim with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I used a cherry stain touch up pen to blend the sanded and polished rim top with the colour of the rest of the bowl. Once the stain dried I wax it with carnauba wax and buffed it with a buffing wheel to polish and make it shine.I rubbed the bowl down with Before & After Restoration Balm to deep clean the briar. The product works to clean, enliven and protect the briar. I hand rubbed it with my fingers and worked it into the finish. I wiped it off with a soft cloth. I buffed the bowl with a micromesh cloth to polish it. The briar really began to have a rich shine. I took some photos of the bowl at this point to mark the progress in the restoration. I set the bowl aside and worked on the stem. I took it out of the deoxidizer and rinsed it under warm water to rinse off the mixture. I blew air through the stem and ran water through it as well to rinse out the mixture there as well. The stem still had some oxidation spots but it was all on the surface as seen in the first two photos below. I painted the surface of the stem with the flame of a Bic lighter to lift the tooth marks. One of the benefits of the lighter is that it burned off the sulfur on the surface of the stem. It did not take too much work for the vulcanite to return to its smooth condition. I sanded out the remaining tooth marks and chatter with 220 grit sandpaper until both sides were smooth at the button. I polished the stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I wiped the stem down after each pad with a damp cloth to remove the sanding dust. I used the Before & After Pipe Polish to remove the small minute scratches left in the vulcanite. I finished by wiping the stem down with a final coat of Obsidian Oil and set it aside to dry. I put the stem back on the pipe and carefully worked the stem over with Blue Diamond to polish out the remaining small scratches. I gave the bowl several coats of Conservator’s Wax and the stem several coats of carnauba wax and buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The finished pipe is shown in the photos below. This interesting Italian made Harvey Futura pipe came back to life nicely with the restoration. This one will be going on the rebornpipes store shortly. It will be a great yard pipe or working pipe. The dimensions of the pipe are Length: 5 3/4 inches, Height: 1 3/4 inches, Outside diameter of the bowl: 1 1/4 inches, Chamber diameter: 3/4 inch. Thanks for walking through the restoration with me.

The Worst Pipe I Ever Bought

3 Replies

Blog by Robert M. Boughton

Copyright © Reborn Pipes and the Author except as cited
https://www.facebook.com/roadrunnerpipes/

Look beneath the surface; let not the several quality of a thing nor its worth escape thee.
— Marcus Aurelius (121 AD – 180 AD), Roman Emperor, in Meditations

NOTE: My decision to post this blog was difficult because of my failure thus far to restore the pipe to a suitable condition.  The project remains a work in progress.  I now know what needs to be done to finish the job and will discuss those steps after the “Restoration” I offer now in a guileless attempt to show what horrors can follow the online purchase of a pipe that is just plain rotten to the core – a Frankenstein, if you will.  Still, this is no excuse for my frustrating defeat.  Maybe I should have extended the title to add “and the Worst Restoration I Ever Committed.” RMB

INTRODUCTION

Old Marcus knew what he was about, and his meditation on recognizing the full potential of a thing speaks to this precise pipe in an almost prescient way.  I wish I could say I always heed the sage advice, but I cannot tell that big a lie.  In the case of this tiny, smooth (in the roughest sense of the word), straight apple purported to be a Kaufman Brothers and Bondy Rocky Briar apple, I failed to a degree that does not now escape me in the least.  Where I should have listened to the voice in my head that screamed how the color was just wrong – not red or maroon but what I call Chinese Fake – part of me didn’t care because it was so cheap.  As it turned out, that term took on more than one meaning as well.  Where the numerous photos of the pipe offered for examination online showed blatant signs of serious damages, visions of repairing each of them overcame my usual better instincts and blinded me to the obvious conclusion that something still graver was hidden.  The result, as I suggested in my opening Note, is the absolute worst job of repairing a pipe I have ever made.  And so, when I opened the petite package that arrived soon enough in the mail and absorbed the monstrous truth, all that saved me from an explosion of temper was the song “Always Look on the Bright Side of Life,” from Monty Python’s Life of Bryan, and particularly the opening.

Some things in life are bad
They can really make you mad
Other things just make you swear and curse.
When you’re chewing on life’s gristle
Don’t grumble, give a whistle,
And this’ll help things turn out for the best.

I mean, what else could I do but whistle, other than spend more than it was worth in return postage to the seller who went out of his way to hide the one definite fatal flaw, which was a pin-point hole in the bowl?  Oh, but if only that were the sole point at issue with this small yet abominable pipe!  Here are the sometimes poor but always honest pics I snapped with my old cell phone, showing every detail. The actual unique Chinese Fake color shows best in the fifth and sixth photos, close on the front and top with the latter including the stripped end of a small paper clip inserted through the hole it penetrated with precision.  This inexplicable tunnel, by the way, has no signs of being caused by a burnout.  It’s as if someone deliberately pierced through the dubious wood to test its physical density, perhaps a previous owner who was as doubtful as I that it’s briar.

The next shot above reveals the approximate length, beside the pack of six-inch long cleaners, to be a little more than an inch short, or the size of a salesman sample.  If the pipe were a real KBB, without the ampersand as shown in the nomenclature pic – and I’m stating categorically that I do not believe it is – then it would date to the early 20th century, at least pre-1930s.  More about that later.

Now, a little extra info about the size, which would be expected to make the pipe light.  But this thing has so little density as to be comparable to holding your empty palm before you and imagining a visible cloud of radon, the heaviest noble gas at 4.4 g/cubic cm, floating there!  Okay, okay, for those who don’t go in for such sarcasm, compare the weight at most to a strip from the tail end of a classic Guillow’s Balsa Wood Flying Machine Kit.  And that’s no exaggeration.

Returning to the veracity of the dainty pipe’s origins having any connection to KB&B, take a close look at the Reg US Pat No in the last shot above.  The number is 298978, which is a known KB&B Patent even though neither I nor anyone else I found searching online for a copy seems able to find one.  However, the number is fortunate in having two instances each of the numerals 9 and 8.  Now give the nomenclature still more scrutiny, and you’ll see neither pair is the same.  That is, the 9s don’t match each other any more than the 8s.  This sort of inconsistency just doesn’t happen in Patent stamps on pipes made by legitimate brands.  The two 8s are easier to spot the problem: the one at the end of the first half of the number is in the form of two separate tiny zeroes, one atop the other, while the final digit clearly shows a connection, or intersection, of the halves.  There’s also the absence of any shape number on the right shank that is present on every real Rocky Briar ever made.  Here are the two pertinent pictures again, this time followed by genuine KBB Rocky Briar examples.  Never mind the glare on the right shank of my fake; you won’t spot any number on the successive views following the worthless pipe’s restoration either.

See the weakness of the marks on my pipe as opposed to the crispness of the others.  Also note the varied but normal stain colors of the three authentic specimens, which can be viewed better at links in the sources, compared to the obvious dodgy glaze or varnish that clings to the questionable wood of mine as though still desperately trying to gain purchase.  I’ve made my point, but I’m sure those who doubt the very real and common existence of pipe forgeries will insist I just got my hands on a bad apple if I may be allowed the pun.

RESTORATION

Let’s escape the hideous stummel altogether for the short time possible and start with the bit.  At least it’s Vulcanite for sure!Cleaning the bore with isopropyl alcohol was easy.  I suspect nobody who ever smoked the pipe did so more than once.Having read in this forum that using a small, relatively soft Brillo pad is a less invasive way to begin smoothing a bit, that’s how I began.  You’ll notice I still needed some practice with the method that was new to me.Then I gave it a wet micro mesh all the way from 1500-12000 with my older kit.And the same dry treatment with my newer kit.I recall using my Bic to pull out the minor chatter but seem not to have bothered recording the step.  Anyway, here’s how it worked out – a little dark, I apologize.Alright, fun time’s over.  For the stummel, I commenced the process that at times made me despair of the point of it all with the 150-grit side of a sanding pad.  At least I achieved a spotty resemblance to briar.See?  Still no sign of a shape number.

Here the thought that someone poked that hole in the bowl on purpose will seem a little saner.  My only guess at the cause of the glaring black mark, like a dark shape from a photo of the moon, is that it’s some weird sort of filling.  Check out the wear around the shank opening.  Does that look like briar?I gave the outer wood another full micro mesh progression, and it even started to look somewhat prettier. I stuffed the pin hole, from the chamber side, with wood putty and sealed the outer bowl side with Super Glue using the same exposed end of the paper clip from earlier.  Later I know I smoothed it with several of the finest micro mesh pads, but again didn’t record it.The next step was giving the wood a real stain.  I used Lincoln Brown Leather Dye and flamed it with my Bic.Hoping to obscure the dreadful damage to the front of the pipe with the darkness of the stain, I micro meshed from 3600-12000.  Everything was fine at that point but the front view. This is when the whistling stopped for the last time, and the gloves came off.  If the foul spot wouldn’t play nice, I rationalized, I’d just have to get rough.  And so, in inexcusable anger, I took 220- and 320-grit papers to the whole misbegotten stummel, micro meshed all the way one last time and gave the wood a few spins of carnauba.  Again, all but the final step went un-photographed, so ready to be done with the mess was I.  Somewhere in all the above steps I did retort the pipe.

Alrighty, then, here I go with the frankly awful results.Take a deep breath with me, as here comes the most deplorable result of my efforts, and the remainder.

Any doubters of the notion that this pipe is a forgery should consider the final closeup of the nomenclature showing the mottled stem mark.  Compare it again to Steve’s salesman sample stem crisp logo.

CONCLUSION

Embarrassment does not begin to describe the thoughts I’m having as I finish up this shameful example of how badly things can go when emotions are allowed to interfere with the task of dealing with each stage of a pipe restoration.  The work shown here was set aside at least a year ago in sheer disgust and mental exhaustion after setting out with such lofty ideals.  The fact that I knew I would never offer the pipe for sale and kept it for my own perverse enjoyment does nothing to mitigate my responsibility for the outcome.

I have not given up – I never do – but only taken the time to gird myself for the final confrontation.  In fact, it should be simple now, a mere matter of gentle sanding to remove the obvious abundance of scratches followed by another round of micro mesh, then re-staining the stummel dark brown or maybe maroon before the final electric buffing with carnauba.  And, of course, fixing the stem alignment.

Marcus Aurelius really had it right with the opening quote.  Quality and value are to be found in everything, regardless of the degrees.  My job remains to bring out the full potential for this faux KBB.

SOURCES

http://www.pipephil.eu/logos/en/logo-kbb.html#rockybriar
https://www.smokingpipes.com/pipes/new/peterson/moreinfo.cfm?product_id=40705
https://www.smokingpipes.com/pipes/estate/united-states/moreinfo.cfm?product_id=200676
https://rebornpipes.com/2016/08/12/restemming-and-restoring-a-tiny-kbb-rocky-briar-1540b-salesmans-pipe/
https://forums.arrowheads.com/forum/information-center-gc33/fakes-frauds-reproductions-authentication-gc94/identifying-fakes-reproductions-gc95/123908-pipe-smoking-instrument-fakes
http://pipesmagazine.com/forums/topic/warning-fraudster-on-ebay-selling-counterfeit-eltangs-possibly-castellos-etc
https://www.smokingpipes.com/pipes/new/castello/moreinfo.cfm?product_id=272648
https://pipedia.org/wiki/Kaywoodie
https://rebornpipes.com/2014/12/15/narrowing-down-a-date-for-kaufman-brothers-bondy-kbb-and-kbb-pipes/

Replacing a tenon on a 1983 Pipa Croci Bent Dublin

2 Replies

Blog by Steve Laug

The local pipe and cigar shop sent a fellow to me the other day with a broken tenon that needed to be replaced. He had dropped it in the snow while shoveling the walks and the tenon had snapped. He pulled the broken tenon out of the shank and tried to reglue the tenon in place with the broken part. Needless to say it did not work. He wanted to have the tenon replaced so he left it with me. The pipe was a nice little Pipa Croci sandblast Dublin. The bowl and rim were both sandblasted and there was a smooth band around the shank and up the underside where it was stamped. It read Pipo Croci over Fatta a Mano (Hand Made) over Mantova, Italia and finally the date – dal 1983. It is a light weight well-made pipe with an acrylic stem. The stem has the insert bar and dot logo on the top side. There were tooth marks on both sides at the button but otherwise the stem was in good condition. He wanted the new tenon and a basic cleanup on the pipe. I found the replacement Delrin tenon and took the following photos. I took a photo of the logo and the stamping on the underside of the shank. I rolled the shank and took a second photo to show the dates stamp.I flattened the broken remnant of tenon on the end of the stem to give it a smooth face. I drilled the airway with a bit a little larger than the airway. I moved through 3 other drill bits until it was large enough for the threaded tenon.I used a Dremel and sanding drum to reduce the diameter of the tenon to fit the mortise of the pipe. While I was at it I roughed up the threads on the tenon to give the glue something to grip.I cleaned up the threads on the tenon and the inside of the drilled out airway and coated the tenon end with black super glue gel. I fit it in the stem and adjusted the stem and tenon for a clean fit against the shank. I set the stem aside to let the glue cure on the new tenon. I scrubbed the briar with Before & After Restoration Balm, working it deep in the grooves and valley of the sandblast. I scrubbed it with a cotton swab to work it into the briar. The balm cleans, protects, restores and enlivens the briar. I buffed it with a horsehair shoe brush and rubbed it to a shine with a cotton cloth. Once the glue cured I put the stem on the pipe and buffed it with Blue Diamond to polish out the scratches. I gave the bowl several coats of Conservator’s Wax and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfibre cloth to deepen the shine. The following photos show the finished pipe. It is ready to go back to its owner who I am sure is looking forward to smoking a bowl in it once more.

Rejuvenating an Interesting “Malaga” Rusticated Pot

Leave a reply

Blog by Steve Laug

The next pipe on the worktable is another “Malaga” – this one is a Pot shaped pipe, or maybe you would call it an author. It is short and rusticated with a smooth rim top, smooth band around the oval shank and a smooth panel on the underside of the shank for the stamp. Jeff has picked up other pipes of this brand since we picked up the ones from Kathy’s Dad’s estate. They are of various shapes and finishes – rusticated, smooth and mixed finish. They are also various sizes from small to very large. They were all made by the Malaga Pipe Shop in Royal Oak, Michigan. They are all from various places around the US. It is interesting to see how far Malaga pipes traveled from one little pipe shop in Michigan. The more I work on the brand the more I am impressed by the quality of the craftsmanship and beauty of the pipes that came from the shop. I wrote a blog to give a little history of the Malaga Brand if you are interested: https://rebornpipes.com/tag/malaga-pipes/. There are also links there to a catalogue and the maker George Khoubesser.)

The bowl is rusticated on the sides, bottom and shank with a pitted pattern in the rustication. The rim top is smooth as is the band around the shank end and the bottom smooth panel where it is stamped. The rim top is smooth but also dirty and damaged. There were nicks in the top of the rim and the outer edges were rough from knocking the bowl out against something hard. There were also some nicks on the inner edge of the rim. The underside of the shank is stamped “Malaga”. The combination of smooth rim and ring along with the rusticated finish around the bowl all work together to create an unusual looking pipe. The bowl had a thick cake and there was a lava overflow on top of the rim. There was some dust and debris in the finish of the bowl and on the top of the rim. The vulcanite stem was oxidized and had tooth chatter and tooth marks on both sides of the stem at the button and on the edges of the button as well. The combination of medium and dark brown stain worked together to create a warm brown finish. Once again it is a light weight pipe for its size. Once more I think it bears testimony to my belief that Malaga pipes were oil cured. Jeff took close up photos of the bowl and rim to show the condition of the pipe before he started to work his magic on it. The bowl had a thick dark cake and some overflow on the rim top. The beveled edge was quite dirty. The inner and outer edges of the bowl showed some damage and nicking. The second photo shows the rim top from a different angle and you can see the tars and oils on the rim top. The third photo shows the underside of the bowl and the rustication. He took a photo of the underside of the shank to show the stamping. The stamping is readable and is the standard “Malaga” stamp with quotation marks on either side of the word. You can see the dust and grime on the finish of the shank.The next photos show that the stem was quite heavily oxidized. There was some light tooth chatter on both surfaces of the stem near the button and on the button edges as well.  Jeff reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils and tars on the bowl, rim and shank. He rinsed it under running water. He dried it off with a soft cloth. Once more he soaked the stem in Before & After Stem Deoxidizer to remove the oxidation. I took photos of the pipe to show its condition before I started my work on it.   I took a photo of the rim top to show the condition it was in after the cleanup. Jeff was able to remove the darkening and tars from the rim top and edges. The grain on the top is very nice and the top is clean. There were dents in the surface of the rim and the outer edge was quite rough on the back side from knocking the pipe out against a hard surface. The inner of the bowl is in good condition. It is a nice looking finish. The stem was clean and you can see that the deoxidizer had done a great job removing the oxidation. There were tooth marks and chatter on both sides of the stem and some slight wear on the edges of the button.Once Jeff had removed the thick cake in the bowl it revealed some fissures in the bottom and part way up the sides of the bowl.I decided to take care of that first as the JB Weld mixture takes time to cure. I mixed the two parts together and pressed the mixture into the fissures in the bowl. I used a dental spatula to spread the mixture into the fissures and around the entry of the airway. It would take time for the mix to cure but I kept working on the bowl.Once the mix had set I topped the bowl on a 220 grit topping board to remove the damage to the surface. It did not take too much to remove the damage to the rim. I cleaned up the inner edge of the rim with a folded piece of 220 grit sandpaper. I polished the rim top with micromesh sanding pads to remove the scratches and marks in the briar. I wet sanded it with 1500-2400 grit pads and dry sanded it with 3200-12000 grit pads. I wiped the rim down after each pad using a damp cotton pad.   I used folded sandpaper and a Dremel and sanding drum to sand out the bowl to remove the excess JB Weld and leave it only in the fissures. Once it was sanded it out I wiped the interior down with a damp cotton pad.I mixed a batch of pipe mud and coated the bowl with that to cover the bowl sides and bottom.I rubbed the bowl down with Before & After Restoration Balm to deep clean the rusticated briar and the smooth rim. The product works to clean, enliven and protect the briar. I hand rubbed it with my fingers and worked it into the rustication with cotton swabs. I wiped it off with a soft cloth. I buffed the bowl with a horsehair shoe brush to polish it. The briar really began to have a rich shine. I took some photos of the bowl at this point to mark the progress in the restoration. I “painted” the tooth marks on the stem and button with the flame of a Bic lighter. I moved the flame quickly across the surface of the stem and repeated it until the tooth marks had lifted.All the tooth marks lifted except one on the underside of the stem. I filled it in with clear super glue. Once it had cured I sanded the repair smooth with 220 grit sandpaper and blended it into the surface of the rest of the stem. I also shaped the surface of the button on the top and the bottom edges to blend in the marks on the surfaces.I polished the stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I wiped the stem down after each pad with a damp cloth to remove the sanding dust. I used the Before & After Pipe Polish to remove the small minute scratches left in the vulcanite. I finished by wiping the stem down with a final coat of Obsidian Oil and set it aside to dry. I gave the bowl several coats of Conservator’s Wax and buffed it with a shoe brush to raise the shine. I used a microfiber cloth to raise the shine on the bowl. I put the stem back on the pipe and worked it over with Blue Diamond to polish out the remaining small scratches. I gave the bowl several more coats of Conservator’s Wax and the stem several coats of carnauba wax and buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The finished pipe is shown in the photos below. This rusticated “Malaga” has been brought back to life. Still deciding if it is one that I will keep or whether I will sell it on the store. If you are interested let me know and I will keep you in mind. The dimensions of the pipe are Length: 5 1/4 inches, Height: 1 1/2 inches, Outside diameter of the bowl: 1 3/4 inches, Chamber diameter: 1 inches. Thanks for walking through the restoration with me as I worked over this Malaga. I have quite a few more to work on in the days ahead.

A Challenging Makeover for a GBD New Standard 9242 Rhodesian

3 Replies

Blog by Steve Laug

I finished the restoration work on Mark’s uncle’s pipes and a few of his own and sent them back to him in late January of this year. I wrote a blog on each of the restorations. They were a fun batch of pipes to restore for him. He sent me another package a few weeks ago that had just three pipes in it – A GBD Classic Straight Bulldog, a GBD 9242 Rhodesian (one of my holy grail pipes) and a long Churchwarden pipe. Each pipe had a different set of issues that would provide a variety of challenges. The Bulldog was in excellent condition other than the first ½ inch of the stem missing in chunks. The Churchwarden had a broken tenon stuck in the shank. By far the worst of the lot was the 9242 pipe. When I saw it in the bag I was excited. When I took it out of the bag I was saddened at the condition of the pipe. The bowl was dirty and there was some lava and rim darkening on the top. There were a few nicks in the edges of the bowl. The finish was dirty but the grain on the pipe was really nice. If I had stopped my observation at this point I would have been quite happy.

But to stop there would not begin to tell the story of the abuse carried out on this pipe. Someone (I cannot call them other than a hacker) had taken upon themselves to do a stem repair for a broken tenon and in doing so almost destroyed an otherwise nice looking stem. I think that it had a broken tenon so the hacker had pulled out the broken tenon from the shank. He had drilled out the end of the stem – so far so good right. If he had quit then it would have been good. But he did not. He found a piece of steel tubing and drilled out the mortise to fit it – but did so at an angle and hacked up the inside of the mortise. The stem itself was not only drilled but had been opened up even more to accommodate the tube. In fitting it in the stem he had cracked the stem on one side. Fortunately it appeared that it did not go all the way through. He then slopped glue – an amber looking goop, all around the sides of the scored tube and shoved it into the airway on the stem. It was not even close to straight. Then he smeared some of the same glue on top of the crack, wiped it off a bit and called it good. This poor pipe really was in awful condition.

When I wrote Mark to give him my assessment I laid out the issues on this pipe I think he must have laughed. He knew that once I saw it, because it was a shape that is on my hunt list, I would be hooked and have to try to fix it. He as much as said so in his email back to me. Sooo… here we go on that restoration project. The photos show the look of the pipe when it arrived in all of its tattered splendour. Note the beautiful grain on the bowl. It was a beautiful looking piece of briar. Note the stem damage and obvious angle of the stem in the shank. Note the repaired split in the stem. Note the tooth marks on the stem on both the top and underside on and in front of the button. This was a project for certain and I figured I could not really make things worse… but then again who knows. I took a close up photo of the rim top to show the general condition of the pipe. You can see the nicks in the briar rim top and on the inner edge. You can also see the fit of the stem to the shank as well as the tooth marks and damage to the stem from the “repair” that had been done to the stem.I took the stem off the bowl to show the metal tubular tenon on the stem end. It looks to me that the drilling out of the stem and the moving the tenon around in the stem caused the damage in the stem surface.I took photos of the end of the stem showing the tenon and the drilled out mortise in the shank. You can see the damage to both. The metal tenon is not totally round and it is heavily scored and damaged. The fit in the stem is crooked so there is no way to align the stem and the shank.I smoothed out the light damage on the rim top with 220 grit sandpaper and then with 1500-4000 grit micromesh sanding pads. I rubbed the bowl down with Before & After Restoration Balm to deep clean the briar and the smooth rim. The product works to clean, enliven and protect the briar. I hand rubbed it with my fingers and wiped it off with a soft cloth and buffed it with a shoe brush to polish it. The briar really began to have a rich shine. I took some photos of the bowl at this point to mark the progress in the restoration. I set the bowl aside and worked on the stem. I used a cotton swab to dribble acetone around the stem/tenon joint. I repeated that process for several weeks on a daily basis. I wanted to dissolve the epoxy that held the metal tenon in place in the stem. While it sat I filled in the damaged areas on the stem surface and the deep tooth marks in the top and underside of the stem at the button with black super glue and set the stem aside to dry. Once the glue had cured I sanded the repairs smooth with 220 grit sandpaper and blended them into the surface of the stem. There were still some small spots that needed work but overall it was starting to look better. I dribbled acetone into the area around the metal tenon every morning and evening after work. I was pretty certain that after a matter of time the epoxy would give way and I would be able to remove the tenon. I wiggled it daily with a pair of pliers to loosen it. This afternoon it finally came loose and I was able to remove it from the stem.With the metal tenon removed from the stem I was able to clean out the airway in the stem and the drilled out area of the stem. I used pipe cleaners, cotton swabs and alcohol to clean out the debris and tobacco oils.The replacement tenon was a little larger than the mortise and needed to be sanded down. I used a Dremel and sanding drum to reduce the diameter of the tenon. I also carefully sanded the face of the stem to smooth out the damage there, Once I had the fit correct in the shank I worked on anchoring it in the drilled out stem. I coated the threaded tenon with some thick gel glue and inserted it in the hole in the stem. I lined things up with a pipe cleaner in the airway and set the stem aside to dry. While the glue on the new tenon cured I cleaned up the inside of the mortise. I hand turned a drill bit that was the same size as the tenon slowly into the mortise to clean up the jagged drilling on the inside of the mortise. I turned it into the mortise to smooth out the misdrilling that had been done to fit the metal tenon. Once I was finished I sanded it lightly and then put the stem in the shank to have a look. The fit was pretty good at this point. Once the tenon had cured I worked on the stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I wiped it down with Obsidian Oil after each micromesh pad. After I finished with the 12000 grit pad I gave it another coat of oil. I polished the stem down with Before & After Pipe Polish – Fine and Extra Fine. I finished by giving it one more coat of Obsidian Oil and put it aside. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel. I gave it several coats of carnauba wax and buffed it with a clean buffing pad to raise a shine. I hand buffed it with a microfiber cloth to deepen the shine. The finished pipe is shown in the photos below. The repair on the right side of the stem is still visible and I will need to work on that a little bit more but the overall look and fit of the stem is far better than when I began on this project. It won’t take too much more work before it is ready to head back to Mark for his smoking pleasure. This is one of those pipes that suffered much at the hands of someone trying to repair something and actually making it worse. I think it is better than it was… thanks for looking.

Restoring a Smooth House of Robertson Apple

Leave a reply

Blog by Steve Laug

I am working on the last of the House of Robertson pipes that Jeff picked up on his weekly pipe hunts. He found several others that are quite unique in an antique mall near where he lives. There were two large long shanked pipes – one round shanked and one square shanked. The third of the batch that he found is a nice little classic apple shape. It looks tiny with the size of the other two. The two larger pipes are a combination of smooth and rusticated. They both have smooth panels on the sides or front of the pipes. Both of the large ones are banded with a sterling silver band. It seems to me that the bands on both the square shank and the round shank are decorative rather than a repair for a cracked shank. I have restored the larger rusticated pipes already and they have traveled to two House of Robertson collectors – on in Idaho and one in Utah. I am finally getting to the third – the small apple. Like the other two, in fact like all of them the name House of Robertson roughly hand-etched on the side of the shank with an engraving tool. I am including the information that I found when I received my first of the House of Robertson Pipes. I found a link on Pipedia that gave me the only information I could find on the brand. I include that in total as it is interesting to read.

“House of Robertson” was in business for many years, but alas, closed their doors in 1999. They were located in Boise, Idaho. They are noted for making rather large and interesting pipes. Thayne Robertson was a Master Mason, AF & AM, and started the shop about 1947 and his son Jon started working there in 1970 when he finished college, along with Thayne’s daughter. Thayne and his son started making the big pipes at that time, and made them together until 1987 when Thayne passed away. Jon kept the store and his sister moved on to other things. The House of Robertson appears to have closed around 1999. https://pipedia.org/wiki/Robertson

While this pipe looks tiny in the photos above it is really an average sized pipe. The curve of the apple shaped bowl leaves the bottom almost flat and the pipe sits nicely on the desk top like a sitter. It is completely different from the two larger pipes in that it is completely smooth with no rustication. The bowl has some interesting grain on it – almost circles on each side and some flame grain. The bowl is caked with some lava overflow on the rim top. The outer and inner edges of the rim look to be in good condition. It is engraved with the House of Robertson signature on the left side of the shank and on the right side it is stamped Algerian Briar. The pipe was dirty but underneath all of the grime it appears to be in excellent condition. It is definitely an interesting pipe and should clean up very well. The fit of the stem to the shank was good. The stem was lightly oxidized and had some small tooth marks and chatter on both sides near the button. Jeff took photos of the pipe before he started the cleanup. The next two close-up photos show the finish on the top of the bowl and the underside of the bowl. The first photo shows the cake in the bowl and the lava overflowing onto the rim top. The grain on the top of the bowl and the inner and outer edge of the rim looks really good. The finish on the rim top appeared to be in great condition under the lava coat. The second photo shows the front and underside of the pipe. The finish is decent condition under the grime.The next photo shows the etched name on the left side of shank on the shank. It reads House of Robertson. On the right side it is stamped Algerian Briar.The tapered stem was lightly stamped France on the underside near the stem/shank union. It was oxidized and had tooth chatter and marks on both sides of the stem near the button. The edge of the button had some dents in it as well. Jeff did a great job cleaning the pipe on the inside and outside. He reamed the bowl with a PipNet pipe reamer and cleaned up the remnants with the Savinelli Fitsall Pipe Knife. He scrubbed out the mortise and the airway in the shank and stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl with a tooth brush and Murphy’s Oil Soap to remove the dust in the rustication on the bowl and shank as well as the smooth portions. He rinsed it under running water. He dried it off with a soft cloth. Once the dust and debris were removed the finish was dull but appeared to be in excellent condition. He soaked the stem in Before & After Pipe Stem Deoxidizer and rinsed it under warm water to remove the deoxidizer gel solution. I took photos of the pipe to show its condition before I started my work on it. I took a photo of the bowl and rim top to show how well it had cleaned up. There is some rim darkening but you can see the interesting grain on the top of the bowl. The stem looks lightly oxidized and the tooth marks and chatter are very light.I worked on the darkening of the inner edge of the rim with a folded piece of 220 grit sandpaper. I smoothed out the inner edge as can be seen in the second photo.I polished the rim top with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I wiped the rim top off with a damp cotton pad after each sanding pad. The surface began to take on a nice shine. I worked Before & After Restoration Balm deep into the smooth finish to clean, enliven and protect the briar. I hand rubbed it with my fingers and worked it into the finish then set it aside to dry for a little while. I wiped it off with a soft cloth. I buffed the bowl with a cotton cloth to polish it. It really began to have a deep shine in the briar. I took some photos of the bowl at this point to mark the progress in the restoration. The grain on the bowl stands out with interesting lines moving across the sides of the bowl and the shank. I looked over the stem a bit before working on it. There was an odd inner tube contraption that stuck out from a deeply funneled tenon. The tube was crooked and slightly bend. I examined it and found that it had a crack in the bottom of the aluminum so a slight movement and it fell off in my hand. I cleaned out the funneled area with cotton swabs and alcohol and ran pipe cleaners and alcohol through the stem quite easily now that the end of the tube was gone.I sanded the stem with 220 grit sandpaper to remove the oxidation on both sides of the tapered stem and remove the tooth marks and chatter on the top and bottom sides at the button.  I polished out the sanding scratches and marks in the vulcanite with micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding it with 3200-4000 grit pads. I wiped the stem down with Obsidian Oil after each sanding pad. I buffed the stem with Blue Diamond on the buffing wheel. I brought it back to the table and sanded it with the final three 6000-12000 grit pads. I polished it further with Before & After Pipe Polish – using both the Fine and Extra Fine Polishes. I gave it a rubdown with Obsidian Oil one last time and set it aside to dry. I put the stem back on the bowl and worked the pipe over on the buffing wheel using Blue Diamond to lightly polish the stem. I buffed the bowl and stem to raise the gloss on the briar and the vulcanite. I gave the pipe multiple coats of carnauba wax. I buffed the entire pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The finished pipe is shown in the photos below. The medium brown stains on the smooth apple shaped bowl works well with the rich black of the vulcanite stem. The dimensions of the pipe are: Length: 5 1/4 inches, Height: 1 5/8 inches, Outside Diameter: 1 1/4 inches, Diameter of the chamber: 3/4 inches. This is an interesting piece of briar, cross grain and birdseye on the bowl and shank. The patterns on the sides are almost circular. I really like how the briar and the vulcanite work well together. This one will soon be on the rebornpipes store. If you are interested in adding a House of Robertson to your collection this may well be the one for you. Thanks for walking with me through the restoration process.

Restoring Barry’s Dad’s Pipes #5 – a French GBD Speciale Canadian

3 Replies

Blog by Steve Laug

I have been including some of the back story in each of the restorations of these pipes because to me the story gives colour to the pipe as I work on it. I am including it once again. Skip over it if you want to. Late in the summer of 2017 I received an email on rebornpipes blog from Barry in Portland, Oregon. He wanted to know if I would be interested in purchasing his Dad’s pipes. I have finished three of them so far, a 1939 Dunhill Patent Shell Bulldog, a Comoy’s Grand Slam Zulu and a Comoy’s London Pride Liverpool. After I finished the second pipe Barry wrote me an email that gave me a little more information on his Dad and incidentally on himself as this pipe was one of his own. Here is what he wrote me.

Steve, — Another great restoration and writing to go with it. I appreciate these pipes more watching the work it takes to get them in good condition.

Your (mine?) floral words about my father are perhaps a little deceptive. Inside that man was a lifelong Bolshevik. Who yearned for the revolution and settled for the party of Roosevelt. His parents were born in the Russian Empire (Ukraine), his father having escaped after brief detention during the 1905 failed uprising and to avoid conscription. His father was gruff, a bit crude and all politics. Given those origins he made the best of himself, had tons of friends and would have been a great social worker.

I misled you on the origin of his pipe conversion. It seems clear based on the 1939 pipe that he smoked a pipe in college, returning to them after the 1964 Surgeon General ‘s report on the danger of cigarettes. After that he only reverted to cigarettes at moments of great stress, a death, business setback or a fight with his wife.

He gave me two pipes in college – the GBD bulldog and a “Parker”. The latter I used to smoke a few times but found I was allergic to it, fortunately. The GBD was to get girls with an MGB, a Harris Tweed sport coat with leather elbow patches and jug wine. Didn’t work. Stanford women were in revolt and saw through the pretense. I put both pipes away for nearly fifty years and now they are in your good hands. — Barry

Barry and I corresponded back and forth and concluded our deal. I became the proud owner of his Dad’s pipes. The inventory of the pipes he would be sending included some real beauties – Comoy’s, Parkers, Dunhills and some no name brands. They were beautiful and I could not wait to see them. I had him send them to Jeff where he would clean them up before I received them. Jeff took some photos of the lot as he opened the box. Each pipe was individually wrapped with bubble wrap and taped to protect them. There were 25 bubble wrapped packages and a lot of pipe accessories included – pipe racks, reamers, scrapers and Comoy’s filters and washers. There were pipe pouches and a wooden cigar box that held all of the accessories and reamers. There was a boxed KleenReem pipe reamer that was virtually unused. Jeff unwrapped the pipes and took pictures of the estate showing both the pipes and the accessories. Barry had labeled each pipe with a sticky note. It was an amazing addition to my pipe and tool collection. The next pipe I chose to work on from the collection was GBD Canadian with a cracked shank. The shank had been repaired with a piece of tape. In the photo above it is the pipe on the bottom of the three GBD pipes. I have no idea once again if this is an original stem. I do not think it is as there is no rondel on the stem top. It was stamped on the top side of the shank vertically near the shank bowl union and reads GBD in an oval over Speciale. On the underside of the shank it reads Paris over France. There is no shape number present on this pipe. I was unfamiliar with the  Speciale line and had never seen a GBD stamped in this manner. I looked it up on Pipedia to check out the various GBD Lines and found that it was not listed on the charts that I could access on the web.

This petite Canadian was interesting to me in that it was a GBD line that I had not seen before and because it had some beautiful grain on the bowl and shank. The shank had two cracks on the underside and the cracks met and a small piece of briar was loose. The classic Canadian shape has an oval shank. The finish was dirty and filled with the detritus of years of use followed by sitting unused. The bowl was thickly caked and had an overflow of lava on the rim top. The outer edges of the rim were rough from knocking the pipe against something hard. There was some burning on the top front of the rim. Even through the grime and grit the amazing birdseye on the sides and cross grain on the front and back of the bowl. The crack in the shank has been glued and taped back together with a piece of black electrical tape. The stem is a short oval shape and fits in the shank very well. It is most likely not the original stem as it does not have a brass rondel on the top side. It could certainly be a well-made replacement stem that his father had paid a great craftsman to make for the pipe as he had for several of his other pipes. It was lightly oxidized and had tooth chatter and deep tooth marks on both sides of the stem at the button. Jeff took photos of the pipe before he cleaned it up. As usual the photos tell the story better than my words can. He took some close up photos of the bowl and rim top to show the cake and the condition. The outer edges of the rim show damage. The top of the rim had some lava build up and had scratches and nicks in the surface. He also took a photo of the underside of the bowl to show the grain. It is a really nice piece of briar and should clean up well. He also photographed the stamping on both sides of the shank to show what it read and the condition of the stamping. The topside of the shank is stamped with the GBD oval over Speciale and on the underside it is stamped Paris over France. Someone had taped the cracked shank and stem together with black electrical tape. Jeff removed the tape and took photos of the shank repair. The stem was made of hard rubber and was oxidized as mentioned above and had tooth chatter and marks. There was also some calcification on the stem surfaces. Jeff took photos of both sides of the stem to capture their condition before he cleaned the pipe.Jeff once again did his usual great job on cleaning this pipe, leaving it pristine and without damage to the finish. He reamed the bowl with a PipNet pipe reamer and cleaned up the remnants with the Savinelli Fitsall Pipe Knife. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim and shank with a tooth brush and Murphy’s Oil Soap to remove the grime of the smooth finish on the bowl and shank. He rinsed it under running water. He dried it off with a soft cloth. Once the dust and debris were removed the finish looked very good.  He soaked the stem in Before & After Pipe Stem Deoxidizer to remove the light oxidation, rinsed it with warm water and dried it off. I took photos of the pipe to show its condition before I started my work on it. I took some close up photos of the bowl, rim top and damaged areas around the outer edge of the bowl. The front edge was rounded over. The bowl was very clean and the rim top had some nicks on both the inner and outer, some scorching and general darkening. Jeff had been able to remove the lava from the finish. The inner edge was in good condition and the roughness of the outer edge was visible. The stem is lightly oxidized as can be seen in the photos and has small tooth marks near the button on both sides.I took some photos of the cracked shank to show the damage. I put the stem back in place to show how the crack opened when the stem was present.I took out the broken chip of briar and glued the edges and pressed in place in the shank. I held it in place until it dried. Once the glue had dried I took a band out of the box that would work on the shank. I pressed it into an oval. I heated it and pressed it onto the shank by pressing it against the desk pad. The photos show the process of banding the shank. I put the stem back in the shank and took photos of the pipe with the stem in place. The band actually looks really good on the pipe and works well with the briar and vulcanite. I took close up photos of the fit of the stem against the band.I started working on the stem next. The photos show the process of the stem work. I used a Bic lighter to “paint” the tooth marks on the surface of the stem to raise the dents in the vulcanite. I was able to raise them quite a bit. I sanded out the tooth chatter and the lighter tooth marks next to the button on both sides with 220 grit sandpaper. I wiped the stem surface clean with a damp cloth. I dried if off and filled in the dents with clear super glue. Once the glue had cured I sanded it with 220 and 400 grit sandpaper to blend the repairs into the surface of the vulcanite. I polished stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I wiped the stem down with Obsidian Oil after each pad. I polished it with Before & After Pipe Stem Polish, both Fine and Extra Fine. I gave it a final coat of Obsidian Oil and set it aside to dry. To remove the damage on the rim I decided to top the bowl. I used 220 grit sandpaper on a topping board to remove the damage. I worked on it until the top was smooth and the damage on the outer edge of the bowl was minimized. I used a folded piece of 220 grit sandpaper to smooth out the damages along the outer rim. I used it to also work on the inner edge of the bowl. I gave the inner edge a slight bevel like it original had before I started.I polished the rim with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit micromesh sanding pads. I wiped it down after each pad to check on the progress. I worked Before & After Restoration Balm deep into the briar on the smooth finish to clean, enliven and protect it. I wiped it off with a soft cloth. I buffed the bowl with a cotton cloth to polish it. It really began to have a deep shine in the briar. I took some photos of the bowl at this point to mark the progress in the restoration. The grain on the bowl is really beginning to stand out and will only do so more as the pipe is waxed. This GBD Speciale Canadian is a beauty. The grain on the bowl and shank is really stunning. The rim top looks much better. The nickel band works well with the briar and the black vulcanite. I am not sure the stem is original or a replacement but it is definitely older. Once again I would guess that Barry’s Dad replaced the stem somewhere along the journey of its life. I suppose we will never know. The vulcanite is high quality and shined up well. I buffed the bowl and the stem with Blue Diamond polish to raise the shine on the briar and the vulcanite. I was careful to not buff the stamping and damage it. I gave the bowl and stem multiple coats of carnauba wax. I buffed the entire pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The finished pipe is shown in the photos below. The rich brown stain allows the grain to really stand out on this little pipe and it works well with the polished nickel band and the rich black of the vulcanite stem. This GBD Speciale Canadian, Paris, France is a beautiful looking pipe. The dimensions of the pipe are: Length: 5 1/2 inches, Height: 1 5/8 inches, Outside Diameter: 1 1/4 inches, Diameter of the chamber: 3/4 inches. This old pipe will fit really well in someone’s collection. The richness of the grain, the band and the polished will stand out as a nice smaller Canadian. There is something about these older GBDs that add a touch of real class to a collection. I will be putting it on the rebornpipes store shortly. Thanks for walking through the restoration with me.