Tag Archives: restaining a bowl and rim

This Long Pencil Shank Viborg French Made Lovat is a real Beauty

Blog by Steve Laug

I woke up to the sound of something large jumping on the roof next to our bedroom window around 4:30am this morning. That gave me an early start at the work bench. I have to tell you that on days like today I miss my old supervisor Spencer who would greet me no matter what time and beg for a treat… strange to not have him here. Ah well time to work. The next pipe, the second one on the table today, came to us in a group of pipes that we picked up through an online auction in 2017 in Wilder, Idaho, USA so it has been sitting here for a while. Even though the finish was a dirty and worn it had some charm showing through the grit and grime of the years. On the left side of the shank it was stamped Viborg [over] Made in France. The pipe is a long pencil shanked pipe with an elliptical shaped bowl. The saddle stem would make it a long Lovat but the stem is also long! The finish is filthy with grime and oil ground into the briar of the bowl and shank sides. The bowl had a thick cake and there was an overflow of lava on the rim edges. There was some damage to the inner edge of the bowl as well. The stem was a vulcanite saddle stem that was oxidized, calcified and had tooth marks and chatter on both sides ahead of the button. Jeff took some photos of the pipe to show its overall condition before he started his cleanup work. He took a photo of the rim top and bowl to give a clear picture of the thickness of the cake and the lava and dust ground into the rim top. You can also see the damage to the inner edge of the bowl and the burn marks on the top back. He also took photos of the top and underside of the stem to show the chatter and tooth marks. Otherwise the stem is quite clean. Jeff took photos of the sides and heel of the bowl to give a picture of what the briar around the pipe looked like. There are a lot of white putty fills on the right side of the bowl and on the right and underside of the shank. He took a photo of the stamping on the shank. It reads as noted above and is clear and readable. The pipe is a bit of a mystery to me. The Viborg name sounds like it should be Danish but the pipe is stamped Made in France. I looked on Pipedia and Pipephil’s site and nothing was listed for the brand on either one. Perhaps one of you know the brand and could shed some light on it for us all. Thank you!

Jeff had cleaned up the pipe with his usual penchant for thoroughness. He reamed the pipe with a PipNet Pipe Reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He worked over the debris on the rim top and was able to remove it. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He soaked the stem in Before & After Pipe Stem Deoxidizer and rinsed it off with warm water. He scrubbed the stem with Soft Scrub and cotton pads to remove remaining oxidation on the ferrule and the stem. He rinsed it with warm water and dried it off. I took photos of the pipe once I received it. It really looked good. The rim top and the inner edge of the rim were clean but the damage was very evident. The stem had remaining oxidation and a few small tooth marks and chatter on both sides near the button. I took a photo of the stamping on the underside of the shank. It was clear and read as noted above. I removed the stem and took a photo of the pipe to give a sense of the whole. The pipe has a vulcanite saddle stem. I decided to address the damaged white putty fills first. I cleaned up the area in the fills and then replaced them with briar dust and super glue. It tends to turn the repair dark but anything would look better to me than the white spots on the bowl and shank. When the repairs had cured I flattened them with a small file and then smoothed them out with a folded piece of 220 grit sandpaper. I wanted to start the process of blending them into the surrounding briar so I wanted them smooth to touch. With that finished I wanted to address the damage to the rim top and inner edges of the bowl. I topped the bowl on a topping board with 220 grit sandpaper. I worked over the inner edge with a folded piece of 220 grit paper. The rim top and edges looked considerably better once I was finished. To help mask the fills on the bowl and shank and to make the grain stand out better I stained the pipe with a black aniline stain. I flamed it to set the stain and repeated the process to ensure good coverage. Once it had cured I wiped down the bowl with isopropyl alcohol to begin the process of removing the black from bowl while leaving it in the grain. I polished the bowl and the rim top with 1500-2400 grit micromesh sanding to remove more of the stain and make the grain stand out more. Once I had finished the sanding I buffed the pipe with red Tripoli and then brought to the worktable for the top coat of light brown stain. I applied the stain and flamed it. I repeated the process until I had proper coverage. I buffed the bowl with Blue Diamond on the buffing wheel and then brought it back to take it through the entire range of micromesh sanding pads – 1500-12000 grit pads. I wiped the bowl down after each pad to remove the sanding dust. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips. I used a horsehair shoe brush to work it into the plateau on the rim top and shank end. The product works to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This interesting French Made Long Pencil Shank Viborg Lovat with a vulcanite saddle stem is a great looking pipe now that it has been restored. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished French Made Viborg Lovat fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 ¾ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ x 1 3/8 inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 23grams/.78oz. I will be adding it to the rebornpipes store shortly in the French Pipe Makers Section. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Look at the grain on this Stanwell Regd No. 969-48 Freehand

Leave a reply

Blog by Steve Laug

I woke up to the sound of something large jumping on the roof next to our bedroom window around 4:30am this morning. That gave me an early start at the work bench. I have to tell you that on days like today I miss my old supervisor Spencer who would greet me no matter what time and beg for a treat… strange to not have him here. Ah well time to work. The next pipe on the table came to us in a group of pipes that we picked up from an Antique Store in Montana, USA in mid-2019 so it has been sitting here for a while. Even though the finish was a dirty and worn it had some amazing grain showing through the grit and grime of the years. On the underside of the shank it was stamped Stanwell [over] Regd. No. 969-48 [over] Made in Denmark. The pipe is a freehand and there is no shape number stamped on it at all. The finish is filthy with grime and oil ground into the briar of the bowl and shank sides. The bowl had a thick cake and there was an overflow of lava on the rim top filling in the plateau and inner bevel of the rim. The stem was a fancy turned vulcanite stem that fit snugly in the ferrule. It had the Stanwell Crown S faintly stamped on the topside of the saddle stem. The vulcanite was oxidized, calcified and had tooth marks and chatter on both sides ahead of the button. Jeff took some photos of the pipe to show its overall condition before he started his cleanup work. He took photos of the rim top and bowl to give a clear picture of the thickness of the cake and the lava and dust ground into the plateau finish of the rim top. There is dust and debris stuck to the walls of the bowl clearly visible in the photos. He also took photos of the top and underside of the stem to show the chatter and tooth marks. Otherwise the stem is quite clean. Jeff took photos of the sides and heel of the bowl to give a picture of what the briar around the pipe looked like. There are a lot of angles on this pipe and there is some stunning grain under the grime. He took a photo of the stamping on the shank. It reads as noted above and is clear and readable. I turned first to Pipephil’s site to get a quick idea of when this pipe was made by reference to the Regd. No. on the underside of the shank (http://www.pipephil.eu/logos/en/logo-stanwell.html). I quote what I found there.

The “Regd. No.” stamping discontinued in late 1960s to very early 1970s.

I also turned to Pipedia’s article on Stanwell but it did not add any further information. It is a great read in terms of the history of the brand (https://pipedia.org/wiki/Stanwell).

With that information in hand I knew what I was dealing with in terms of the stamping and the age of this pipe. I knew from the information from Pipephil that the Regd. No. stamping was discontinued in the late 60s to very early in the 70s. Now it was time to work on the pipe.

Jeff had cleaned up the pipe with his usual penchant for thoroughness. He reamed the pipe with a PipNet Pipe Reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He worked over the debris on the rim top and was able to remove it. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He soaked the stem in Before & After Pipe Stem Deoxidizer and rinsed it off with warm water. He scrubbed the stem with Soft Scrub and cotton pads to remove remaining oxidation on the ferrule and the stem. He rinsed it with warm water and dried it off. I took photos of the pipe once I received it. It really looked good. The rim top and the inner edge of the rim looked very good after the cleaning. It had a few small tooth marks and chatter on both sides near the button. I took a photo of the stamping on the underside of the shank. It was clear and read as noted above. I removed the stem and took a photo of the pipe to give a sense of the whole. The stem is fancy turned vulcanite. I polished the bowl and the smooth portions on the rim top with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiping it down after each pad with a damp cloth. The bowl had lightened around the top edge and on the shank end. I touched up the stain on the bowl with a Maple stain pen. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips. I used a horsehair shoe brush to work it into the plateau on the rim top and shank end.. The product works to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. I “painted” the stem surface on both sides with the flame of a lighter to lift the tooth marks. I was able to lift all of them on the underside of the stem but two of them on the topside remained. I filled them in with clear super glue. Once the repairs cured I reshaped the button with a rasp and a file. I smoothed out the repairs further with 220 grit sandpaper. I started the polishing with 400 grit wet dry sandpaper. I touched up the faint stamping on the top of the stem. It was a Stanwell Crown S logo. Parts of it were faint but I was able to get some of the stamping to show up with the Rub’n Buff Antique Gold. I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This beautiful Stanwell Regd. No. 969-48 Freehand with a fancy, turned vulcanite stem is a great looking pipe now that it has been restored. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Stanwell Danish Freehand fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 ½ inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 54grams/1.90oz. I will be adding it to the rebornpipes store shortly in the Danish Pipe Makers Section. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Restoring a Mixed Finish Soren Hand Carved Pedestal Freehand

Leave a reply

Blog by Steve Laug

The next pipe on the table came to us in a group of pipes that we picked up from an auction in 2018 in Wilkes Barre, Pennsylvania, USA. It has a mixed sandblast and smooth finish that was a bit dull and lifeless. It showed promise under the grit and grime of the years. On the underside of the shank it was clearly stamped Soren [over] Hand Carved [over] Made in Denmark. When I received it from Jeff somehow the bowl and stem had separated and I had the bowl in hand but no idea what stem fit the shank. I tried a variety of stems that I had but not one of them fit well.

I looked up the brand on Pipephil (http://www.pipephil.eu/logos/en/logo-s10.html) and found that the brand was carved by Søren Refbjerg Rasmussen. Pipes that he made for the European market were mostly stamped “Refbjerg” while those made for the US market were stamped “Soren”. Thus I knew that one I was working on was imported into the US market.

I decided to set the stem aside and see what I could find in my cans of stems here. I found an interesting turned stem that had a lot of potential. It had some oxidation, calcification and deep tooth marks on the surface. The tenon was a perfect fit in the shank so I would just need to clean it up and repair the tooth marks. Here are some photos of the stem as it looked before I worked on it. I put the stem on the pipe and took some photos of the look of the “new” stem on the bowl. I think that with some work this was the right stem for the pipe. I took a close up photo of the bowl and the stem to give an idea of what I had to work with. The bowl was very clean and it would polish up nicely. There was still some darkening in the plateau on the back side of the bowl that would need to be dealt with. The stem photos show the oxidation, calcification and deep tooth marks on both sides near the damaged button surface. It was badly damaged but showed a lot of promise. I removed the stem from the shank and dropped in a bath of Briarville’s Pipe Stem Deoxidizer to soak while I worked on the bowl. I figured the soak would bring the oxidation to the surface and clean the surface so that I could do the repairs to the stem surface once it was clean.While the stem soaked in the deoxidizer I worked on the bowl. I scrubbed the rim top with a brass bristle brush to remove the darkening and deep grime. Once it was finished it looked much better. I stained it black with a black stain pen. I used the wire brush again to clean up some of the high spots leaving the stain in the grooves. I also lightly sanded the rim top with a 1500 grit micromesh sanding pad to further highlight the high spots. I like the look of the rim at this point though with more polishing and Balm it would come alive. I polished the smooth portions of the bowl sides with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped the bowl down with a damp cloth after each pad. With the smooth portion of the briar polished I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips and into the plateau rim top and sandblast with a horsehair shoe brush. The product works to clean, enliven and protect the briar. I let the Balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. While the Balm did its work I worked on the “new stem”. I set the bowl aside and turned my attention to the stem. I removed it from the Deoxidizer bath and rubbed it down with a coarse cloth to dry it out. It had brought oxidation to the surface and made it easier to deal with but it had not removed it. The good news for me was that it had done a great job removing it from the tooth marks. I “painted” the surface of the vulcanite with the flame of a lighter to lift the dents as much as possible. I was able to lift them significantly. I filled in the remaining divots with black super glue. I chose to use black glue this time just in case there were some remaining spots of oxidation in the tooth marks. The black would take care of that. Once the repairs had hardened I scrubbed the remaining oxidation in all of the grooves of the fancy stem with Soft Scrub all purpose cleaner. I was able to get into the grooves with the product and the cotton pads that I used to scrub it. It was beginning to look better. I cleaned out the stem with alcohol and pipe cleaners to remove the tars and the debris that was loosened by the deoxidizer bath.I smoothed out the repairs and recut the button edges with a rasp and a file. The stem was taking shape. I smoothed out the remaining repair marks and the file marks with 220 grit sandpaper. I started the polishing with 400 grit wet dry sandpaper. I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This beautiful Soren Hand Carved Pedestal Freehand with a fancy, turned vulcanite replacement stem is a great looking pipe now that it has been restored. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Soren Hand Carved fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 ½ inches, Height: 2 ½ inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 72grams/2.54oz. I will be adding it to the rebornpipes online store in the Danish Pipemakers section. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

New Life for a Sandblast Savinelli de Luxe Milano 506 Panel Billiard

Leave a reply

Blog by Steve Laug

When my brother Jeff saw this pipe he went for it. He picked it up from a fellow in Pocatello, Idaho, USA. This pipe appeared to be in rough shape. The bowl was full and the sandblast was filthy. It had definitely seen better days. However, there was something about the shape that caught Jeff’s eye. The stamping on the underside of the shank reads de Luxe [over] Milano. That is followed by the Savinelli S shield logo and the shape number 506 over Italy. It is faint but readable with a loupe and light. The bowl and shank are sandblasted with a rugged blast and the panel sides all have indents where the blast went deep into the grain. It is an interesting pipe. The stain on the bowl is a medium brown that highlights the sandblast finish. It is a panel billiard with a square shank and a saddle vulcanite stem. The pipe was dirty with a thick cake and tobacco debris in the bowl. There was a heavy overflow of lava on the rim top that made it hard to know if the rim edges were damaged. There were dark areas on each side of the bowl. The grime and dirt had been ground deeply into the sandblast finish. The stem was calcified and heavily oxidized and was a brownish green colour. There was tooth chatter and tooth marks on both sides of the stem near the button and on the button surface itself on both sides. Jeff took some photos of the pipe before he did his cleanup.The next photos show the bowl and rim top. You can see the cake in the bowl and the overflow of lava and grime on the top. You can also see the likelihood of damage to the rim edges but also that it is impossible to know what it would look like once it was clean. The photos of the stem show a lot of tooth chatter on both sides of the stems. There are also some tooth marks on the button top and bottom. The sandblast finish on the bowl, though dirty, showed interesting patterns – straight grains and birdseye. There were also some swirls in the grain. The photos also show some darkening on each side of the bowl and some dark spots. The stamping on the underside of the shank is faint but readable. It reads as noted above. I had a vague memory that there was a great photo of the same pipe in a smooth finish on the Pipephil site (http://www.pipephil.eu/logos/en/logo-savinelli1.html). I turned there and sure enough it was not only a De Luxe it was also a 506 Panel Billiard with a smooth finish. I have included a screen capture of the section from that site below. There was also a link to a series of shape charts for Savinelli Pipes that I have found helpful in the past (http://www.pipephil.eu/logos/en/infos/savinelli-chart.html). I did a screen capture of the section of the chart that included the 506 shape. Now it was time to work on the pipe. Jeff worked his magic in cleaning up this pipe. He reamed it with a PipNet reamer and smoothed the walls of the bowl with a Savinelli Fitsall pipe knife. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim and shank with a tooth brush and Murphy’s Oil Soap to the oils and tars on the bowl, rim and shank. He rinsed it under running water. He dried it off with a soft cloth. The cleaning of the stem raised more oxidation in the vulcanite. The tooth marks and chatter was clean but visible. I took the stem off and put it in a bath of Before & After Stem Deoxidizer and totally forgot to take pictures of the pipe before I started. I took photos of the condition of the rim top and stem before I started working. The rim top looks very good and the bowl is spotless. The rim top is heavily darkened and stained. The stem has light oxidation remaining and some tooth chatter and marks on both sides near and on the button. I took a photo of the stamping on the underside of the shank. The stamping was faint but still readable. It reads as noted above. The stem has a brass bar on the left side of the saddle. I started my work on the bowl by dealing with darkening around the bowl sides. I took photos of the darkening. I poked and probed them with a dental pick to check on the integrity of the briar and it was solid. I also worked the areas over with a brass bristle brush and was able to remove some of the darkening. There was no cracking or checking on the inside of the bowl in each of those areas so I was fairly certain I was dealing with darkening caused by the oils of the pipeman or woman’s hands who had previously smoked the pipe. I would need to stain the pipe to deal with the dark areas. I stained the bowl with an aniline Light Brown stain. I was surprised at how dark it came out on the bowl itself. I applied the stain and flamed it with a lighter to set it in the grain. I set it aside while I had dinner to let the stain cure. After dinner I took the pipe off the cork rest and took photos of the newly stained bowl. You can see the depth of the blast in the photos below. I worked some Before & After Restoration Balm into the finish of the bowl, rim top and shank with my fingertips to clean, enliven and protect it. I find that the balm really makes the briar come alive again. The contrasts in the layers of stain really made the grain stand out. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The bowl really looks good at this point. I set aside the bowl and turned my attention to the stem. I “painted” the tooth marks on the surface of the stem and was able to lift them significantly. I filled in the remaining tooth marks on the button surface with clear super glue. I used a file to smooth out and shape the button. I smoothed out the remaining repairs with 220 sandpaper to blend them and started polishing with 400 grit wet dry sandpaper. I scrubbed the stem with Soft Scrub All Purpose cleaner to remove the residual oxidation on the stem surface. The product works very well to cut through residual oxidation on vulcanite. I polished the stem with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. I polished it further with Before & After Pipe Stem Polish – both fine and extra fine. I really enjoy finishing the work on a pipe because I love bringing it back to life and then administering the final touches that make it sing. I put the Savinelli De Luxe Milano 506 Panel Billiard back together and lightly buffed the bowl with Blue Diamond. I buffed the stem with a heavier touch with Blue Diamond on the buffing wheel. I gave the bowl multiple coats of Conservator’s Wax and worked it into the deep sandblast with a horsehair shoe brush. I gave the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. It is fun to see what the polished bowl looks like with the smooth finish and the black vulcanite saddle stem. This richly finished De Luxe Milano Panel Billiard is light weight and ready for you to load up a tobacco of preference and enjoy smoking it. Have a look at it in the photos below. The dimensions are Length: 5 ¼ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 33grams/1.16oz. This is one that will go on the Italian Pipemakers section of the rebornpipes online store shortly. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next generation.

Fresh Life for a Savinelli Oscar Lucite 111KS Billiard

Leave a reply

Blog by Steve Laug

The next pipe on the work table came to us 2018 from a fellow in Pocatello, Idaho, USA. It is a nice looking Billiard with cross grain and birdseye grain and has a Fancy Lucite half saddle stem. The Lucite stem fits the name on the left side Oscar Lucite. The bowl has a rich reddish brown colour combination that highlights grain. The pipe has some grime ground into the surface of the briar. The finish had a few small fills around the sides but they blended in fairly well. This pipe is stamped on the sides of the shank. On the left it reads Oscar [over] Lucite. On the right it has a Savinelli “S” Shield and next to that was the shape number 111KS [over] Italy. There is a thick cake in the bowl and an overflow of lava on the top beveled inner edge of the bowl. The rim top looks good but it is hard to be certain with the lava coat. There were some light tooth marks and chatter on both sides of the Lucite stem near the button. The pipe looks to be in good condition under the grime. Jeff took photos of the pipe before he started his cleanup. He took photos of the rim top to show the thick cake and the thick lava coat. It is hard to know what the condition of the rim top and edges is like under that thick lava. It is an incredibly dirty pipe but obviously one that was a great smoker. The acrylic half saddle stem had light tooth marks and chatter on both sides ahead of the button. He took a photo of the sides and heel of the bowl to show the beautiful grain around the bowl and the condition of the pipe. You can see the grime ground into the surface of the briar. He took a photo of the stamping on the left side of the shank. It is clear and readable as noted above. On the underside of the shank it is stamped Savinelli Product. I turned first to Pipephil’s site to look at the Savinelli write up there and see if I could learn anything about the Oscar Lucite line (http://www.pipephil.eu/logos/en/logo-savinelli3.html). There was a listing for the Oscar Lucite and I did a screen capture of the pertinent section.I looked up the Savinelli brand on Pipedia to see if I could find the Oscar Lucite line and the 111KS Shape (https://pipedia.org/wiki/Savinelli). There was nothing that tied directly to the line I am working on. There is a detailed history of the brand there that is a good read. I also captured the shape chart and boxed in the 111KS shape in red. The shape is identical to the one that I am working on. The stem on this one is the original shape that was on the Lucite Line but there was no shooting star logo on the left side.It was time to work on the pipe. As usual Jeff had done a thorough cleanup on the pipe. He reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils and tars on the rim and the grime on the finish of the bowl. He rinsed it under running water. One of the benefits of this scrub is that it also tends to lift some of the scratches and nicks in the surface of the briar. He dried it off with a soft cloth. He cleaned the internals and externals of the stem with alcohol, pipe cleaners and cotton swabs. He scrubbed the stem with Soft Scrub all-purpose cleanser and rinsed it off with warm water and cleaned out the airway in the stem with alcohol. Other than the damaged rim top the pipe looked good. I took a photo of the rim top and stem to show the condition. The rim top was in very rough condition. The rim top and the edges of the bowl had darkening, burn marks and some nicking. The Lucite half saddle stem had light tooth chatter and marks on both sides ahead of the button and on the button edges. The stamping on the sides of the shank is clear and readable as noted above. I removed the stem from the shank and took a photo of the pipe to give a sense of the whole. It is a nice looking billiard that should clean up very well. I started working on the pipe by dealing with the damaged rim top and edges. I topped the bowl with 220 grit sandpaper on a topping board. I worked over the rim top and inner bevel of the rim with 220 grit sandpaper. I smooth out the damage and gave the rim top and edge a clean look that would polish out nicely. I wiped the rim top down with a damp cloth to remove the dust and debris. I polished the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiped down the bowl after each sanding pad. I stained the rim top with an Oak stain pen to match the rest of the bowl. Once I buffed and polished the bowl it would be a perfect match. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The Balm did its magic and the grain stood out. I polished the Lucite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. The photo below shows the polished stem. This nicely grained Savinelli Made Oscar Lucite 11KS Billiard with Lucite half saddle stem is a great looking pipe now that it has been restored. The briar is clean and really came alive. The rich reddish, brown stains gave the grain a sense of depth with the polishing and waxing. The grain really popped. I put the vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Oscar Lucite Billiard is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 46grams/1.62oz.Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Restoring a No Name Tortoise Shell Billiard

Leave a reply

Blog by Steve Laug

The next pipe I have chosen is one that neither Jeff nor I remember picking up. It could have come to us through a trade for work on a pipe or it could have come from one of an earlier pipe hunts that either Jeff or I did. Either way, the long and short of it is that this is another pipe that we have no idea how it came into our hands. It is an attractive no name billiard with a tortoise shell stem with a fancy trio of acrylic and wood decoration on the shank end of the stem. It had a smooth finish on the bowl and a inwardly beveled rim top. Under grime on the finish it appears that pipe may have had a light brown or tan stain to highlight the grain around the bowl. There were a few small sand pit fills around the bowl on the left back and the top and right side of the shank. The pipe had no stamping on the shank or underside. There was also no identifying stamp on the stem. It was in decent condition when I brought it to the table. The finish was dirty with grime ground into the briar sides and rim. There was a light cake in the bowl and light lava on the rim top and some damage on rear inner edge of the bowl. The stem was dirty but otherwise in good condition. There were light tooth marks and chatter on the top and underside on and near the button. I took photos of the pipe before my cleanup work. They tell the story and give a glimpse of the promise that we see in this pipe. I took a photo of the rim top to show the interior the bowl and the rim top and inner edge. It is moderately caked with some damage to the rim top and edges and some lava coat on the right and back top of the rim. The Tortoise Shell stem is in decent condition with light tooth marks on the top and underside near the button. The two black acrylic bands were slightly smaller in diameter than the stem and the wooden insert so it gave those areas a slight bulge. I would need to smooth out the transition on both sides of the black acrylic on the stem.I took photos of the sides of the shank to show the lack of stamping. There was no stamping on the shank so it was a bit of a mystery pipe. I took the stem off the bowl and took a picture of the parts of the pipe to give a sense of the parts of the pipe.I decided to begin my work on the pipe by addressing the damage to the rim top and edges. I used a folded piece of 220 grit sandpaper to clean off the rim top and the inner edge of bowl. It took some time but I was able to bring it back to a pretty clean condition. There is a large fill on the rim top on the back right side.The pipe had been reamed recently so all I had to do with it was clean out the shank and airway in the shank and stem with pipe cleaners, cotton swabs and alcohol. I was surprised that I also was removing some brown stain from the end of the shank. The diameter of the shank and the diameter of the black Lucite bands on the stem did not match. I decided to sand down the shank and stem to try and smooth out the transition between them. I sanded the shank as well as the bowl and rim top with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. After each pad I wiped the briar down with a damp cloth. This served a dual purpose of both removing the sanding debris and the dust that had accumulated in the rustication patterns around the bowl and shank. Once I was finished the flow between the stem and shank was much smoother. I touched up the light areas on the sanded shank and the rim top with a Maple stain pen that matched the finish on the rest of the bowl very well. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. It looks quite nice at this point. With that done the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I had sanded the stem earlier to deal with the flow of the bands on the stem end. I also sanded it with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I used the pads to remove the tooth marks on the stem on both sides near the button. I wiped it down after each sanding pad with Obsidian Oil. I am excited to finish this No Name Tortoise Shell Stem Billiard. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with the grain popping through on the bowls sides and rim top. Added to that the polished Tortoise Shell acrylic stem was beautiful. This smooth finished Billiard turned out to be a nice looking pipe that feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 49grams/1.73oz. It is a beautiful pipe and one that will be on the rebornpipes store in the Metal and Pipes from Various Makers section soon. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next pipeman or woman.

Restoring an English Made Hadley Park 213 Lovat

Leave a reply

Blog by Steve Laug

The next pipe on the work table came to us from one of Jeff’s pipe hunts a few years ago and to be honest we don’t remember where we got it. This morning as I was going through my box of what I have to work on this one caught my eye. It is a nicely grained small Lovat with an acrylic stem that is almost butterscotch coloured. The stem reminds me of butterscotch candies that I used to have as a kid. The pipe is stamped on the left side of the shank and reads Hadley Park. On the right side it is stamped Made in London England and to the left of that, near the stem is the shape number 213. The finish had a lot of grime ground into the smooth finish on the bowl and some darkening around the sides of the bowl. The bowl was heavily caked and there was a lava coat and darkening on the rim top and inner edge. The edges looked okay but we would know more after the cleanup. There were a few fills that had shrunken around the sides of the bowl. The stem was dirty and had tooth chatter and marks on the top and underside near the button. There were not markings or a logo on the saddle stem. The pipe showed promise but it was very dirty. Jeff took photos of the pipe before he started his cleanup work. He took a photo of the rim top and bowl to give a clear picture of the thickness of the cake and the condition of the rim top and edges. He also took photos of the top and underside of the stem to show the chatter and tooth marks. Jeff took a photo of the side and heel of the bowl to give a picture of what the briar around the pipe looked like. There is some great grain under the grime. He took photos of the stamping on the shank. It reads as noted above and is clear and readable. I could not find any information on the brand. I thought the shape number might point the way but it did not give the clues I was hoping. The Made in London England stamp is similar to those used by a variety of English pipemakers so that is not definitive either. So I am left not knowing who made the pipe. Now it was time to work on this pipe.

Jeff had cleaned up the pipe with his usual penchant for thoroughness. He reamed the pipe with a PipNet Pipe Reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He soaked the stem in Before & After Deoxidizer and rinsed it off with warm water. I took photos of the pipe once I received it. The rim top and inner edge of the rim showed some damage. The inner edge of the bowl was roughened and showed some darkening. The rim top also showed some damage. The stem surface looked good with some remaining oxidation and tooth marks and chatter on both sides near the button. I took a photo of the stamping on the shank. It is clear and readable as noted above. I removed the stem and took a photo of the pipe to give a sense of the whole. The stem is a short acrylic saddle. I decided to start my work on the pipe by cleaning up the damaged inner edge of the bowl. I reworked the edge with a folded piece of 220 grit sand paper. Once I finished the rim and edge looked much better. I moved next to repairing the damaged fills on the front left of the bowl. I filled them in with clear super glue and briar dust. Once it cured I sanded them smooth and blended them into the surrounding briar. With the repaired fills being lighter than the surrounding briar I decided to restain the bowl with a light brown aniline stain. I applied the stain and flamed it with a lighter to set it in the grain. I repeated the process until I was happy with the coverage on the bowl. Once the stain had cured I removed it from the cork and took photos of the new look before I buffed or polished it at all. I buffed the bowl with red Tripoli and then wiped it down with a cotton pad and isopropyl alcohol to make the stain a bit more transparent and show the grain around the bowl sides. I polished it with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping it down after each pad with a damp cloth. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. I set the bowl aside and turned to work on the stem. I sanded out the tooth chatter and marks with 220 grit sandpaper and started polishing the stem with 400 grit wet dry sandpaper.I polished the acrylic stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This Hadley Park 213 Lovat with an orange/butterscotch acrylic stem is a great looking pipe now that it has been restored. There is some great grain around the bowl and shank. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Hadley Park Lovat is petite but fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 34gr/1.23oz. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Bringing a Beautiful Benaderet’s Smooth Poker/Cherrywood Back to Life

1 Reply

Blog by Steve Laug

The next pipe on the table is a nice looking smooth finish Poker. We picked it up in 2018 from a fellow in Scottsdale, Arizona, USA. The pipe is a real mess with dust and grime ground into the finish on the bowl. There is a thick cake in the bowl and the rim top and beveled inner edge is covered in lava. The cake was so thick in parts of the bowl that it was hard to know for sure what the condition of the rim edge was under the lava. The finish appears to be a reddish brown or oxblood colour with dark highlights underneath. On the left side of the shank it is stamped Benaderet’s [over] Paramount [over] San Francisco. On the right side it is stamped Natural Grain [over] Made in England with the shank number 20 next to the shank bowl junction. The stem was oxidized, calcified and there were light tooth marks and chatter on both sides just ahead of the button. There was not any stamping on the stem so it did not have any identifying marks. Jeff took photos of the pipe before he started working on it. I include those below. Jeff took photos of the bowl and rim top to show the cake in the bowl and the lava build up on the rim top and dust and grime in the finish. It was thick and hard and heavier toward the front of the bowl. Hopefully it had protected the rim and edges from damage. The lava is thick and scattered across the top and there is a buildup on the inner edge of the bowl. The stem shows scratching, oxidation, calcification and light tooth marks on the stem surface and button. Jeff took a photo of the sides and heel of the bowl to show the condition of the finish – the grime and grit all over the sides and bottom of the bowl. Jeff took photos of the stamping on the sides of the shank. It is very clear and readable as noted above. From the Natural Grain stamping and the shape number on the shank I was pretty certain I was dealing with a Comoy’s pipe. The stamping Benaderet’s was a dead end and the shape number 20 seems to point to Comoy’s.

I did a quick google search for a Benaderet’s Pipe Shop and came on two good links. The first is from a post on reddit that included a quick bit of information on the shop being located in San Franscisco, California that closed in the 1970s. (https://www.reddit.com/r/PipeTobacco/comments/dzg3y8/any_info_on_a_benaderet_pipe_year_etc/ ). I quote:

Benaderet’s was a pipe shop in San Francisco that closed in the 70’s. Their house pipes were made by Comoys or Sasieni although smokingpipes had one made by GBD once. Good find.

The other link was to a blog (http://theothersideofthelizard.blogspot.com/2018/11/benaderets-pipe-shop.html). That blog gave the original address of the shop in San Francisco and the names of the owners of the shop.

Benaderet’s Cigarette, Pipe and Tobacco Shop
215 Sutter Street [Formerly at 566 California Street], San Francisco.
Owners: Robert and Edith Rashaw (Robert Rashaw: born 1916. Edith Edna Rashaw: born 1916.)

Store still extant in the late seventies. No longer there by the eighties. At one point, they had Egyptian cigarettes made for them. Their house pipes were usually by Comoys. There are also Benaderet Sasienis. More research required.

Quote: “Benaderet’s Inc. was California’s oldest pipe and tobacco store when it went out of business in 1980. Sam Benaderet was a tobacconist from New York City who came to San Francisco in 1915 to work at the Panama Pacific International Exposition. An immigrant to the United States from Turkey, Mr. Benaderet decided that he liked the West Coast’s Mediterranean like climate. After the Exposition closed, he stayed to open his own tobacco business. This new firm produced custom private-label cigarettes for men’s clubs. A lavish retail store was opened in the late 1920’s that quickly became a mecca for tobacco connoisseurs.”

So what I could find out about the pipe is that it is a pipe probably made by Comoys (The Natural Grain mark and the shape number points to this conclusion). It was made for Benaderet’s Cigarette, Pipe and Tobacco Shop in San Francisco, California. Since the shop went out of business in 1980 I now knew that the pipe was made before that time. Now it was time to work on the pipe.

This pipe was a real mess like many of the pipes we work on. I was curious to see what it would look like when I unpacked it. I was surprised at how good it looked. Jeff reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish on the bowl looked really good when I got it. The rim top looked much better and the inner and outer edges were looking good. He had cleaned the internals and scrubbed the exterior of the stem and soaked them in Before & After Deoxidizer bath to remove the oxidation. The stem looked very good other than the tooth marks and chatter in the surface. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked very good. I took photos of the pipe before I started my work on it. I took photos of the condition of the rim top and stem before I started working. The rim top looks very good. The beveled inner edge of the rim is clean and look great. The bowl is spotless. The stem is clean and has light tooth marks and tooth chatter. I took a photo of the stamping on the sides of the shank. It is clear and readable as noted above.I took the stem off the shank and took a photo of the pipe to show overall look of the parts. It is a nice looking piece of briar and the pipe will be a beauty.I polished the briar with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiped it down after each sanding pad. I decided to leave the few scratches in the briar and they would not steam out and they were minor enough to leave. There were some light spots around the bowl and shank that I touched up with a Maple stain pen to blend into the surrounding briar. I worked some Before & After Restoration Balm into the finish of the bowl and shank with my fingertips to clean, enliven and protect it. I find that the balm really makes the briar come alive again. The contrasts in the layers of stain really made the grain stand out. I let the balm sit for 15 minutes then buffed with a cotton cloth to raise the shine. The bowl looks good at this point. I set the bowl aside and turned my attention to the stem. It was in good condition and the light chatter and marks would be removed when I polished the stem with micromesh sanding pads. I dry sanded it with 1500-12000 grit pads. I wiped it down after each pad with Obsidian Oil. I polished it further with Before & After Pipe Stem Polish – both fine and extra fine. Once again I am the part of the restoration that I always look forward to – the moment when all the pieces are put back together. I put the Benaderet’s Cherrywood/Poker Paramount 20 pipe back together and buffed the bowl and the stem with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. It is fun to see what the polished bowl looks like with the black vulcanite saddle stem contrasting with the colours of the bowl. The reddish brown stain on the Benaderet’s Paramount Cherrywood looks absolutely great. It is nice to know that it has a west coast tie to the San Francisco area and a long gone pipe shop. It must have been a fine smoking pipe judging from the condition it was when we received it. Have a look at it in the photos below. The dimensions are Length: 5 ¼ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 36 grams/1.27 oz. This is one that will go on the British Pipemakers section of the rebornpipes online store shortly. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next generation.

Restoring a Chunky, Rusticated Tom Howard Panel Billiard

2 Replies

Blog by Steve Laug

The next pipe on the table came to us in a group of pipes that we purchased from online auction on in 2018 from Dearborn Heights, Michigan, USA. It is a rusticated Panel Billiard that is in good condition. It is stamped on the sides of the shank. On the left side it is stamped Tom Howard. On the right side it is stamped Imported Briar. The stamping is clear and readable. I have worked on at least one Tom Howard pipe in the past and later in the blog will give a bit of the history. At this point I have to say that the pipe is well made but it is clunky looking and feeling. It does not have the rugged beauty or finesse of a Tracy Mincer Custom-Bilt in my opinion. It has its own charm, to be sure but it is not the same. The age of the pipe and the oils in the finish has given the pipe a rich reddish brown finish. There is also some nice grain that the shape follows well. The finish was dirty with dust around the nooks and crannies of the worm trail rustication. There was a thick cake in the bowl and the rim top showed darkening and some lava. The inner edge showed some potential damage that would only become clear once the pipe was cleaned. The vulcanite taper stem was oxidized, calcified and had tooth marks and chatter ahead of the button on both sides. Jeff took photos of the pipe to show what it looked like before he started working on it. He took photos of the bowl and rim top to show the thickness of the cake and the darkening and lava overflow on the rim top. The photos of the stem show the oxidation, calcification and tooth marks and chatter on the surface on both sides. The photo of the side and heel of the bowl shows the carved worm trail rustication and the grain on the pipe. It looks quite nice under the grime and dust. The stamping on the sides of the shank is shown in the photos below. It looks very good and readable. It reads as noted and explained above. Before I started my work on the pipe I wanted to refresh my memory of the brand. I remembered that Tom Howard was a notable figure beyond pipe making. I also remembered that Dal Stanton had worked on one and done a great job ferreting out the history of the brand and the maker. I turned to his blog on the brand and read what he had written during his restoration of one of the Howard pipes (https://rebornpipes.com/2018/09/16/the-vintage-notoriety-of-tom-howard-and-his-jumbo-squat-rustified-tomato/). I have included the portion of the blog on the history below for ease of reference. (Thanks Dal!)

I had never heard of a Tom Howard stamp on a pipe and after I put the name in search tool on Pipedia I was surprised to find what I found. Tom Howard was a vintage celebrity in America during the 1940s and 50s. Here’s what Pipedia said about Tom Howard the man:

Tom Howard was a popular comedian and personality in the 1940s/50s, known for vaudeville stage and radio work. But he also was a skilled pipe maker. In a Popular Mechanic article from 1947 he is written up as the “Hobbyist of the Month, Tom Howard.” He made pipes in his workshop outside his home in Red Bank, NJ. Starting about 1939 and looks like into the late 1940’s or later. He purchased briar blocks by the bag as well as stem blanks, and in his well-equipped shop he handcrafted his pipes, in about three hours on average. He was a true craftsman, also specializing is intricate model boats, trains and brass canons, all built to scale.

I was intrigued – this vaudeville and stage comedian made pipes and this pipe came from his workshop made by his hands. How cool is that? Desiring to find out more about Tom Howard the man, I searched Wikipedia and found a fun and informative article about his professional life and how he hosted a I was intrigued – this vaudeville and stage comedian made pipes and this pipe came from his workshop made by his hands. How cool is that? Desiring to find out more about Tom Howard the man, I searched Wikipedia and found a fun and informative article about his professional life and how he hosted a zany Q&A game show that was spoofing the ‘serious’ Q&A game shows. It was called “It Pays to Be Ignorant”. Here is what the Wikipedia article said:

It Pays to Be Ignorant was a radio comedy show which maintained its popularity during a nine-year run on three networks for such sponsors as Philip Morris, Chrysler, and DeSoto. The series was a spoof on the authoritative, academic discourse evident on such authoritative panel series as Quiz Kids and Information Please, while the beginning of the program parodied the popular quiz show, Doctor I.Q. With announcers Ken Roberts and Dick Stark, the program was broadcast on Mutual from June 25, 1942 to February 28, 1944, on CBS from February 25, 1944 to September 27, 1950 and finally on NBC from July 4, 1951 to September 26, 1951. The series typically aired as a summer replacement.

Snooping a bit more, I found an online site that had the July 5, 1951 episode of ‘It pays to Be Ignorant’ available for viewing. I watched it and it was like I was in a time machine! The video also included period advertising for cars and tobacco and Tom Howard in form, dawning a professorial gown and a gravelly 1950s vaudeville tin can voice. It’s great! I clipped a picture of the episode. If you want to see it yourself, here’s the link: The Internet Archive.

The Pipedia article I included above, referenced one more source to learn a bit more about Tom Howard. In a 1947 Popular Mechanics edition he was named ‘Hobbyist of the Month’ – but it didn’t say which month! With a little bit of help from Google, I found Archive.org that housed old editions of many periodicals including Popular Mechanics. I started in January and started searching – thankfully they had a search tool I utilized for each month. Finally, I found the article in the Popular Mechanic 1947 June’s edition. For the absolute nostalgia of it, and for the interesting information it adds about Tom Howard and especially his pipe production, I’m including the pages here for you to read – including the cover page! I couldn’t pass it up! Armed with the great information Dal had provided I turned to work on the pipe itself. Jeff had carried out his usual thorough cleanup of the pipe. He had reamed it with a PipNet reamer to remove the cake and cleaned the reaming up with a Savinelli Fitsall Pipe Knife. He scrubbed the internals of the bowl and stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the externals with undiluted Murphy’s Oil Soap and rinsed the bowl off with running water. He soaked the stem in Before & After Deoxidizer and once it had soaked rinsed it off with warm water to remove the residual solution. He dried it off and rubbed it down to remove any oxidation that was still on the stem. The pipe looked much better when I received it. I took a photo of the rim top to show the condition. You can see the darkening and the damage to the inner edge of the rim on the back right. It is roughened and chipped and out of round. The taper stem came out looking quite good. There are tooth marks and chatter on both sides near the button and some damage to the button surface itself. I took photos of the sides of the shank to show the stamping. It is clear and readable as noted above. I removed the stem from the shank and took a photo of the pipe parts to show what I was working with. It is a nice looking pipe.I decided to start the restoration on this one by working on the damage and darkening on the right rear of the rim top. I sanded the rim top with 220 grit sandpaper and gave the inner edge of the bowl a slight bevel to remove the damage and blend it into the rest of the rim edge. I polished the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the bowl down with a damp cloth after each sanding pad. I touched up the sanded rim top and edge with a Maple stain pen to blend it into the surrounding briar. The match is perfect and once the bowl is buffed it will disappear.With the repair completed I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar with my fingertips and a horsehair shoe brush to work it into the nooks and crannies of the rusticated finish. The product works to clean, enliven and preserve the briar. I let it sit for 15 minutes while I worked on the stem. After the time passed I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm. I set the bowl aside and turned my attention to the stem. I filled in the bite marks on both sides of the stem and button with clear super glue and set it aside for the repairs to cure. I reshaped the button with a file and then sanded it with 220 grit sandpaper to smooth it out. I started the polishing with a piece of 400 grit wet dry sandpaper. I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This Tom Howard Panel Billiard turned out to be a nice looking pipe. The rusticated finish looks quite good while not obscuring the grain around the bowl. The stain used on the bowl served to highlight the grain on the bowl. The polished black vulcanite taper stem adds to the mix. With the dust gone from the finish and the bowl it was a beauty and is eye-catching. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel being careful to not buff the stamping. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Tom Howard Panel Billiard is a large pipe and feels great in the hand. Give the finished pipe a look in the photos below. I can only tell you that like the other pipes I am working that it is much prettier in person than the photos capture. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 71grams/2.50oz. Thanks for walking through the restoration with me as I worked over another beautiful pipe. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next generation.

Restemming and Restoring a No Name Billiard

Leave a reply

Blog by Steve Laug

This morning I received another call from a customer sent to me by the local pipe shop. The fellow had a pipe that needed to be restemmed. He said he would stop by and drop the pipe off for me to work on. Irene and I were out and about so he left it in the mail box. When Irene brought it down to me in the shop the smell was overwhelmingly strong and filled the room with the overly sweet smell of years of aromatic vanilla smelling tobaccos. It was in a plastic bag and once I opened the bag it was even more pungent. The bowl was filled with a thick cake that took over half the diameter of the bowl. There was tobacco debris stuck on the walls of the bowl. The cake was sticky and tacky with the tars and oils. The exterior of the pipe was cake with sticky substances around all the sides and on the rim top. The rim top had been beat up and was in rough condition with a thick buildup of lava on the top. The finish was in rough condition with a lot of nicks and gouges around the sides of the bowl and shank. It was really a mess. The stem was chewed and split in half at the button forward for about an inch up the stem. Once I removed it the inside of the shank was as smelly as the rest of the pipe. I took photos of the pipe before I began my clean up. I took a photo of the rim top to show condition of the bowl. You can see the damage to the top and the inner and outer edge. You can see the thick cake in the bowl and the thick lava coat on the heavily damaged rim top. It is a very dirty pipe. I also took photos of the stem to show its condition. It has tooth marks and cracks on the top and underside of the stem near the button. You can also see that the stem does not fit tightly against the shank but has gaps on both sides. I took the pipe apart and took photos of the pipe as a whole. It is in rough condition and I think that the stem was a replacement at some point in its life.The pipe stunk so bad and filled the room with the odor to the degree that I decided to clean the bowl before restemming the pipe. I reamed it with a PipNet pipe reamer using three of the four cutting heads. I removed the cake back to bare walls so I could check for damage to the inside of the bowl from heat or otherwise. I scraped the remainder of the cake from the bowl with a Savinelli Fitsall Pipe Knife and scraped the rim top at the same time. I scrubbed the exterior of the bowl with a tooth brush and undiluted Murphy’s Oil Soap. I worked to get the thick grime off the outside of the bowl and shank. I rinsed it with running water and rinsed off the soap and grime. I cleaned out the shank and the airway into the bowl with pipe cleaners, cotton swabs and isopropyl alcohol to remove the tars and buildup in the shank. I wanted the shank clean before I fit a new stem.I built up the inside edge of the bowl and the damage to the rim top with super glue and briar dust. I layered the mixture on the rim and rebuilt the inner edge. Once I had it built up I topped the bowl on a topping board with 220 grit sandpaper. Once I topped it smooth I stained the rim top with a Maple Stain Pen. I found a stem that was the same diameter as the ruined stem. I turned it on the PIMO tenon turning tool and my hand drill. I took the excess material off the diameter and the length of the stem to get a snug fit in the shank. I took photos of the fit of the stem to the shank. The fit of the stem to the shank end was the same as the previous one.There was a gap on both sides and it sat firm against the top and bottom. I examined the shank end and saw that it had been damaged and was no longer flat. I decided to square it up with a thin brass band as it would give a flat surface for the stem to face against. I glued and pressed it onto the shank end and set it aside to cure. I used the Dremel and sanding drum to take down the excess diameter of the stem and sanded it smooth with 220 grit sandpaper. Once I had the fit correct I put the stem in place on the pipe and took photos of the fit and look at this point in the process. I filled in the nicks and chips in the finish with briar dust and clear super glue. Once it had cured I sanded them smooth with 220 grit sandpaper. I wiped the bowl down with isopropyl alcohol to remove the finish and the dust on the briar. I restained the bowl and shank with a light brown aniline stain. I flamed it with a lighter and repeated the process several times until I had the coverage that I was looking for.Once the stain had cured I took the pipe off the cork and took photos of the stained look of the bowl and shank with the brass band. I wiped the bowl down with isopropyl alcohol to make the stain more transparent. I polished the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the bowl down between pads with a damp cloth. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The Balm did its magic and the grain stood out. I sanded out the scratch marks on stem from the Dremel with 220 grit sandpaper. I started polishing it with 400 grit wet dry sandpaper. I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further the stem. The photo below shows the polished stem. This pipe has come a long way from where it was when I received it to restem. It is not flawless but it looks better. The Vancouver piper who it belongs to has received far more that what he originally wanted – just a new stem. The briar around the bowl is clean and looks better. The rich brown stains gave the grain a sense of depth with the polishing and waxing. The rim top while not perfect is far better. I put the newly fitted vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inch, Chamber diameter: 7/8 of an inch. The pipeman will be picking it up soon and will be reintroduced to this pipe. Thanks for reading this blog and my reflections on the pipe while I worked on it.