Tag Archives: stem work

An Interesting Welsh Pipe Find: A C.A. Sander Sandhurst Bent Bulldog

Blog by Steve Laug

I came across this beautiful sandblast bent bulldog on Ebay and put a bid in for it. I was the sole bidder and won it for a decent price plus reasonable shipping from Great Britain. The pipe is stamped on a smooth spot on the bottom left side of the shank. It reads SANDHURST #16 and next to that it is stamped C.A. SANDER over SWANSEA. The seller stated that the pipe was in a good used condition, and had some wear. He also said that the measurements of the pipe are 135mm or 5.5 inches long, bowl size 35mm or 1.4 inches x 28mm or 1.10 inches. From the photos he included in the sale the finish on the bowl looked to be in excellent shape. The rim was very clean. I could not see the inside of the bowl but the way the rim looked I was guessing that it was very clean. The sandblast was nicely done with some deep craggy ring grain. There was no ring around the cap on the bowl. The stamping on the shank was clear but was weak in spots. The stem was lightly oxidized but had no tooth chatter or bite marks.

I knew next to nothing about the maker of the pipe. I could ascertain from the stamping that the pipe was made by a C.A. Sander in Swansea. I remembered that Swansea is in Wales so I had something to start with. I looked in Who Made that Pipe and also in Lopes book and could find nothing listed for that maker. I used Google to see if I could find any information on the company and looking a company of that name in Swansea, Wales. I actually found out that the company started in 1977 and closed in 1998. It appears from the information that I found to have been a family owned and operated company with broad interests. There was no mention of pipes in any of the company documents that I could find. I wonder if the brand was not just one of many avenues for the company to expand its horizons. I found two pipes online with the CA Sander stamping these included the Oxford and the Sandhurst. Both the Oxford and the Sandhurst are sandblast finish pipes with a dark stain. There was no other information available that I could find listed online. Does anyone have any information on the brand? (I have included a photo of the stamping on a stemless Oxford Bulldog that I just purchased on eBay for comparison.) When the pipe arrived it was in far better shape than the seller intimated. The bowl was lightly smoked if at all. There was no cake and the darkening did not extend to the bottom of the bowl. I ran a pipe cleaner through the shank and the stem and it came out clean. There was dust in the shank that came out but no tobacco oils or tars. The stem was actually less oxidized than I expected and would clean up very easily. There were some tiny tooth chatter next to the button on the top and the bottom side of the stem. There were some small nicks in the vulcanite on the top right side midstem.

I took a close up photo of the rim and bowl to show the excellent condition of the rim and bowl. The second photo below shows the nicks in the stem that I spoke of above. This should be an easy clean up.

The slot in the button was very thin and I was unable to get a pipe cleaner into the airway from that end. I used three different needle files to open it wide enough to take a thick pipe cleaner easily. Once it was open I sanded the inside of the slot to make it smooth. The draw on the pipe is much better after opening the slot. The narrowness of the slot makes me wonder if that is why the pipe was not smoked more.

I sanded the stem with 220 grit sandpaper to remove the oxidation, smooth out the tooth chatter and the two nicks on the right side. Once they were gone and the stem was smooth I used a medium and fine grit sanding sponge to begin to minimize the scratching. I put a plastic washer between the stem and the shank to keep the shoulders sharp and protect the shank while I was sanding.

I wet sanded the stem with 1500-2400 grit micromesh sanding pads and then rubbed the stem down with Obsidian Oil. The oxidation is disappearing and the dark black of the rubber is beginning to stand out. I dry sanded it with 3200-4000 grit micromesh pads, gave it another coat of oil and finished sanding it with 6000-12000 grit pads. I gave it a final coat of Obsidian Oil and then set it aside to dry.

I buffed the pipe and stem with Blue Diamond on the wheel and then gave them multiple coats of carnauba wax. I polished the pipe with a clean flannel buff and then gave it a final buff by hand with a microfibre cloth. The stem cleaned up amazingly well. The pipe is ready for a inaugural smoke. The draw is wide open and easy! Thanks for looking.

Addendum: 06/06/18 I received an email from Andrew in answer to a question I asked in my two blogs on CA Sander pipes. I quote in full his email because of the information that it includes.

Comment: You asked about C A Sander

C A Sander were tobacconists based in Wind Street Swansea. I don’t know exactly when the business started but it it passed to my Grandfather from his father (both were C A Sander) and by the 1920 was a successful and well established retail business with shops all over south wales. They were importers and blenders (if that is the term) of tobacco and the shops sold smoking paraphernalia. At my grandfathers retirement late 60’s to business went to my uncle again C A Sander but known generally as Jim. He developed a business supplying cigarette machines around South Wales and moved out of retail he eventually sold the business to Rothermans and went into other business ventures, I expect that was when the limited company you found was formed. Uncle Jim has now retired but still lives in the area.

Hope this helps with your research.

Andrew I received this followup email from someone who would like to get in touch with you. Here is her email

Hi there – I stumbled upon your website when looking for anything to do with C.A. Sander tobacco shop and I saw the pipe you restored – which is amazing! and then saw the comment below left by Andrew. Since that shop was owned by my grandfather, and Andrew’s grandfather – it would seem that we are cousins – but we have never met. I would love to get into contact with Andrew. Would you be able to assist in that? If possible, could you ask him to contact me at my email address pianokey88@hotmail.com?
Many thanks for your help! Georgina

Reworking a Lucite stem on a Sasieni Litewate Deluxe 71F Long Shank Dublin

3 Replies

Blog by Steve Laug

This pipe caught my eye as I was browsing through the for sale section of the Dr.Grabow Collectors Forum. It was in very clean condition. The finish on the bowl and rim were like new. The pipe was stamped Made in England in a circle on top of the shank next to the stem and in the center of the shank it was stamped Litewate over De Luxe. On the underside of shank near the stem was the shape number 71F. The pipe was barely smoked and was very clean. The stem was obviously a replacement Lucite stem in a bright yellow swirl pattern. In the photos it looks more green than it truly is. In reality it is very yellow.

I looked up the brand on the pipedia site and found that the Litewate was produced by Parker and also sold by R.M. Littaur & Co. Ltd. It was also made by Sasieni. The circular com stamp on the shank and the shape number identified this particular pipe as a Sasieni made pipe. http://pipedia.org/index.php?title=Litewate I copied the next photos from the PipePhil stamping and logos site. The stamping on the pipe I have is exactly like that on these photos. He also noted there that brand was solely distributed in the US Market. When the pipe arrived I was surprised by the sheer size of it – I knew it was small but I had no idea that it would be this small. It was very light weight and reminded me in both the size and the weight of the Stanwell Featherweight series. I unpack it and looked over the stem. It was chunky and thick. The descent of the slope to the button was not even and had a slight flat spot about ½ inch from the stem/shank joint. The button was sloppily cut and the stem was very thick in front of the button. The button itself was thick both in terms of height and in terms of width from the outer edge to what should have been a sharp angle to the slope of the stem. It did not have that angle but was rather another slope to the top of the button. Where there should have been a slot in the stem there was merely an airway – a single hole in the end. This is the way that stem blanks arrive before they have been shaped and fit to the pipe. Overall it looked like a quickly done stem to make the pipe useable. I took some photos of the pipe when it arrived. The next photos show the stamping on the top of the shank and the rim. Whoever did the restem did a great job fitting the stem against the shank. It is a great snug fit that shows no light. The bowl is clean and lightly smoked. I took a few photos of the stem that shows the chunkiness of the button and the thickness of the angle from shank to button. The third photo below shows the single hole airway in the end of the button. I used three different needle files to cut a slot in the end of the button and shape it and the Y in the airway. I used a round, a slight oval and a flat oval file to cut and shape the slot. I straightened the edge on the button and thinned out the button with a flat needle file. I wanted a 90 degree angle rather than the slope that was there originally. I sanded out the newly cut slot with a folded piece of 220 grit sandpaper. I reworked the taper on the stem and thinned it out with 220 grit sandpaper. In the photo above you can see the overall thickness of the stem and the short taper from the hip of the stem to the button. This needed to be thinned and the taper increased. I sanded and shaped the button and cleaned up the straight edge against the stem body. I sanded the stem with a medium and a fine grit sanding sponge and finish the initial reshaping with 400 grit sandpaper. I sanded out the inside of the slot with a folded piece of 400 grit wet dry paper.

I polished the Lucite with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads.

I buffed the pipe and stem with Blue Diamond on the buffing wheel and then gave the pipe several coats of carnauba wax. I buffed it with a clean flannel buff and then by hand with a microfiber cloth. The finished pipe is shown in the photos below. The newly shaped stem is far more comfortable in the mouth now that the taper is more flattened and the thickness reduced. Thanks for looking.

A Pair of Millard Perfect Pipes – A Sandblast Apple and Dublin

9 Replies

Blog by Steve Laug

When I came across the Millard – the Perfect Pipe coupon in the two boxes of Kentucky Club that I found I was fascinated with the look of the pipe. It reminded me of the Keyser Hygienic pipes that I had restored over the years. The stem that fit into the metal mortise shank insert and the tubes on the inside of the stem and the shank were similar. While the Keyser tubing in the shank looked identical the one in the stem was different. Keyser was directed downward while the Millard was two straight tubes that met in the mortise. They did not touch but the metal chamber became a condensing chamber, or as they call it an Action Trap, for the smoke and collected the moisture before it continued through the tube in the stem. I looked up the brand online and found the following advertisement postcard that shows the way the system works. I found that the stems were interchangeable between the shapes that the pipe came in. The straight stems could be easily transferred from pipe to pipe. In fact the pipe originally came with an extra or replacement stem. The pipe came in a sandblast and a smooth finish in six shapes – apple, Dublin, billiard, pear, pot and bent. It came in two sizes: medium or large. In the advertisement below you can see that the pipe cost $3. I also found that Mastercraft supplied the pipes through the coupon sales. Knowing a bit of history about the company I know that they did not make pips so they were sourced from the original manufacturer.I mentioned in the Kentucky Club Blog that I would love to get my hands on one of these. I received a comment from one of the readers, Pam who offered to send me one. She had picked one up in a lot of pipes she was working on restoring. I could have it. I thanked her and she sent me the following photos of the pipe. It is a little (or what Kentucky Club called Medium in the advertisement above). It was a sandblast apple. It was in decent shape and would clean up quite nicely. The finish was spotty and the stain was lightened and missing in some spots. The rim had some buildup of tars. The cake was quite thick. The inner rim edge was out of round. The stem was oxidized and had some calcification in front of the button.

While I awaited the arrival of Pam’s gift I took a look on eBay and found that the pipe that I had pictured in the Kentucky Club Blog was for sale. The seller wanted $12 for the pipe. It was a Dublin shaped pipe with a smooth finish. It looked to be a Medium sized Millard as well. On a whim I put a bid on it and won. The seller said that it was restored but my past experience with these kinds of sales made me pretty certain that all that it meant was that it was polished. Now I went from no Millard pipes to two in a matter of days. The photos that follow were from the seller. The pipe looked sound. The finish was pretty decent though there were ripples and dents on the bowl sides. The beveled rim was not clean and there were still spots where the tars had been left and polished. The inside of the Action Trap was dirty with tars and oils. The stem had some tooth chatter and dents. Once the pipe arrived I would have a better idea of what I had to work with on this one.

Pam’s gift pipe arrived first. It was a beautiful smaller sized apple (even though the advertising from Millard called it a Medium). The length was 6 inches. My original assessment from the photos proved to be pretty accurate. The finish was worn but the sandblast was quite nice – shallow but still tactile. The light spots on the top of the shank were spots where the finish was gone but the blast was still present. The cake was thicker than I thought it would be, particularly in the bottom of the bowl. The bowl was more out of round than I had guessed and had a burn spot on the back middle inner edge that contributed to the misshapen inner edge. The tar build up was deep and there appeared to be a burn spot on the top of the rim at the front right side. The inside of the shank, the Action Trap, was dirty and had tar, oil and tobacco shellac. The airway was tight and constricted when I blew air through it. The stem was oxidized and under the calcification there were some deep tooth marks and cuts that would need to be addressed. The inside of the stem has a chamber with the tube in the middle and that area was dirty with tars and oils. The airway was constricted even more than the one in the shank. I was pretty sure that something was clogging it and causing the constriction. The slot had been reduced by half with the buildup of grime.

The second pipe arrived at my home a short time after Pam’s. It too proved my original conjecture about the concept that some people have of what “restored” means. This pipe had been given a light polish on the briar and the stem. The polish had merely wiped over the dents, dings and scratches on the briar. There were ripples along the top of the shank. The rim still had spots of tarry buildup that had been polished and there were scratches from what looked like a quick scrub with a coarse scrubber. The bowl had a slight ridge around the inside just below the rim from an incomplete reaming. The inside of the Action Trap was dirty and the oils and tars had hardened. The airway was constricted and dirty and the opening in the bowl bottom was plugged with grit. The aluminum mortise insert was oxidized and dull. The stem was oxidized and there were ripples in the surface from where someone had either buffed hard or tried to remove tooth chatter or tooth marks. The inside of the stem chamber was dirty with tars and oils and the inside of the stem looked as if it had never seen a pipe cleaner. So much for the term “restored”.

I decided to work on both pipes at the same time so that I could compare the internals and the briar on them. It would be a fun project to do them both together and watch the truly restored pipes emerge from the tired pipes that had arrived at my work table. The next four photos show the pair together.

I took some close up photos of the two bowls to show what I would be working on. The first photo shows the bowl of the apple shaped pipe. You can see the cake and the damage to the top of the rim. The bowl is out of round. The second photo shows the rim of the Dublin and you can see the scratches and the incomplete cleaning of the rim tars. The next photo shows the stems removed from the shanks. The stems are interchangeable so as I had expected from the advertisement shown above one stem size and shape could be used interchangeably on any of the straight pipes. I took a photo of the internals of the mortise insert to show the tube inset in the middle of the aluminum chamber. This is the Action Trap that the adverts spoke of. The “restored” Dublin was just as dirty inside as the untouched apple sent by Pam. While both look the same the tube in the Dublin extends further into the Trap than the one in the apple. The second photo shows the end view of the two stems. You can see the tube inset in the middle of the stem. Again the tube in the Dublin stem is shorter than the one in the apple. I am not sure the reason for this as when both are interchangeably inserted in the bowl the draw and fit is identical so it may well be just inconsistency in the manufacture. I cleaned up the inside of the Dublin bowl with a PipNet reamer to remove the ridge along the top portion of the bowl just below the beveled rim. I scrubbed the rim with saliva and cotton pads to work on the tars left behind. I found that they were hard so I used a 1500 grit micromesh pad to sand and work on the deposits until they were gone and the rim was smooth. It also worked to remove the scratching on the rim that had been left behind by the previous “restoration”. I reamed the bowl on the apple with the PipNet reamer and took the cake back to bare briar. The second photo shows the large amount of carbon that I removed from the bowl.

With the bowl reamed you can see the damage to the inner edge that left the bowl out of round. There was a burned area on the rim at that point that did not go too deeply into the bowl but it was present. I scrubbed the rim with a brass bristle tire brush to remove the overflow of cake on the rim.

I scrubbed both bowls with a tooth brush and Murphy’s Oil Soap to remove the spotty finish on the apple and the grime on both bowls. I also removed the polish that had been applied to the Dublin so I could work on the scratches and dings. After scrubbing them I rinsed them under warm water in the sink to remove the soap and the grime that had been loosened.

I scrubbed both bowls with acetone on a cotton pad to remove the remaining finish and clean up the briar. The finish on the Dublin was pretty clean. The one on the apple came off with the scrubbing and the remaining finish was removed.

With the bowls and finish cleaned up it was time to address the internals. I used pipe cleaners, cotton swabs and alcohol to clean out the debris in the shank and the mortise of both pipes. I used a folded pipe cleaner and a cotton swab that I thinned the cotton on to get inside of the mortise to clear out the build up there. To address the damaged rim on the apple I decided to top the bowl. I set up the topping board and a piece of 220 grit sandpaper and worked on the rim to flatten it and remove the damaged areas. In doing this I found another burned spot on the front right top of the rim. I worked on the inner edge of the rim with a folded piece of sandpaper to correct the out of round condition. When I was finished the rim looked far better. Now I needed to work on rusticating the rim to match the sandblast on the finish of the pipe.

To rusticate the rim I used a dental burr in my Dremel and carefully worked it over the surface of the bowl rim. It had to be deep enough to show, tight enough to look like a sandblast and somehow blend into the bowl finish. I carefully worked the Dremel over the surface being careful to keep it on the flat rim and not damage the edges of the inside or outside of the bowl. The next two photos show both the burr and the work done on the rim. Though it is a little hard to see the rustication came out really well. It will become clear in later photos. I stained the bowl and rim with a dark brown aniline stain. I applied the stain and flamed it. I reapplied it and reflamed it.

The next photo shows the rustication very clearly. I touched it up with a dark brown stain pen and then waxed the bowl and rim with a microcrystalline Conservators Wax. The bowl was looking far better.

With the basic work done on the bowls and rims I turned my attention to the stems. I cleaned both stems with pipe cleaners, alcohol and cotton swabs until they were clean. I picked out the slots on both stems with a dental pick to make sure they were wide open. The stem on the Dublin had a very tight draw. I ran a straightened paper clip through the stem and a large chunk of tar and cotton from pipe cleaners dropped out of the end. The draw was unconstricted and the airflow was clear in both stems. I sanded both stems with 220 grit sandpaper to remove the oxidation and also clean up the tooth marks and ripples in the surface of the vulcanite. I sanded them with a medium and fine grit sanding sponge to remove the scratches left behind by the sandpaper. I repaired the tooth damage and the cuts in the surface of the stem for the apple with black super glue. After the repair had dried I sanded it with 220 grit sandpaper and the sanding sponges once again. I wet sanded the stems with 1500-2400 grit micromesh sanding pads. I rubbed the stems down with Obisidian Oil and then dry sanded with 3200-4000 grit pads. I gave the stems another coat of oil and dry sanded with 6000-12000 grit pads. I buffed the stems with Blue Diamond on the buffing wheel and then gave them several coats of carnauba wax. I buffed them with a clean flannel buffing pad and then a microfibre cloth.

I polished the aluminum ferrule/mortise inserts on the shanks with the last three grits of micromesh sanding pads and then rubbed them down with a jeweler’s cloth. I lightly buffed the stems and bowls with Blue Diamond and then gave the entire smooth pipe several coats of carnauba wax. I buffed the two pipes with a clean flannel buff and then with a microfibre cloth to raise the shine. The inside of the Active Trap is stained but it is clean. These are a couple of great looking pipes now. The rusticated rim worked really well with the finish on the bowl and gives the apple a clean look. The clean beveled rim on the Dublin has a rich shine that shows the grain off very well. The finished pipes are shown in the photos below. Thanks for looking.

Repairing Cracks in a Large WDC Wellington Bent

4 Replies

Blog by Steve Laug

Through Facebook I connected with a new friend Warren. He wrote me about how to repair a crack in a pipe that he was reworking for a friend of his. As I described the process he asked if he could send it to me to work on. At that point my refurbishing box was getting low as I had repaired and moved out a lot of the pipes that had been there. So I agreed. Last week it arrived here. A funny side note is that I have a stem for the same pipe and have been looking for a bowl for the stem for a while now. Now I get the opportunity to work on a pipe with the same stem. It is stamped WDC in a triangle on the stem with Wellington arced below the triangle. It is also stamped on the left side of the shank with the WDC triangle and Wellington in script to the right of the triangle. Underneath the script it reads Imported Briar. There is no other stamping on the pipe. It is a large pipe with a length of over 10 inches and a bowl height of 2 inches. The diameter of the bowl is 7/8 inches. The third picture below shows a comparison of a 5 ½ inch long pipe and average bowl so you can see how big this pipe truly is.

The briar had some attractive grain in it but there were some issues as well. It had a lot of fills on the front left, front right and bowl front. There was some damage to the surface of the rim that looked as if the pipe had been dropped on concrete. The outer edge of the rim on the front had some damage and was rounded over and the inner back edge of the rim had burn damage that made that portion out of round. Fortunately it was not a deep burn and would be relatively easy to address. There was also a ¾ inch crack on the underside of the shank that had one ¼ inch branch going toward the left side of the shank.

I took a series of close up photos to show the damaged areas of the pipe. The first shows the damage to the rim surface and edges. The second shows the crack in the shank. The third photo shows the missing fills and divots in the bowl sides.

I decided to address the crack in the bottom of the shank first. I used a micro drill bit on my Dremel to drill some small holes at the end of the crack and the branches of the crack to stop the damage from spreading further. The bit is very tiny as can be seen from the holes that are left behind after drilling. I drill two holes on each end because after the first hole I examined it with a lens and could see that extended slightly beyond my first hole. I picked out the damaged putty fills with a dental pick and wiped the bowl down so that I could repair the crack and the fills. I used a clear super glue and fine briar dust to replace the fills and to fill in the drill holes on the shank bottom. In each case I over filled the holes so that as the glue and dust were sanded I would not need to repeat the process due to shrinkage.

My intention was to restain the entire bowl so I sanded the bowl and the repairs with 220 grit sandpaper to smooth out the repairs. I followed that by sanding the bowl and repairs with a medium and a fine grit sanding sponge.

I reamed the bowl with a PipNet reamer starting with the head that would fit and working up a head that took the cake back to bare briar. In looking at the back side of the bowl I could see a small hairline crack and I wanted to know if it went all the way through.

I topped the bowl with the topping board and took off all of the damage to the inside and outside rim as well as the rim surface. I sanded it with the medium and fine grit sanding sponge as well to smooth out the scratches.

After sanding and topping the bowl I could see that indeed there was a hairline crack that went across the rim at 5 o’clock and went down the back side of the bowl about ¾ of an inch. It was small and did not separate. It looked like it went all the way through to the inside of the bowl but upon examination appeared to only extend about 1/16th of an inch into the bowl. I topped it a little bit more to take care of the internal crack. I drilled the back side of the bowl at the bottom of the crack to stop it from going further down the bowl. I wiped down the bowl side and then picked out the crack with a dental pick. I filled it with super glue and briar dust and sanded it down with 220 grit sandpaper and the medium and fine grit sanding sponges until it blended into the surface of the bowl. I picked out the rim crack as well and filled it with the same mix. I sanded it with the topping board once again and then with the medium and fine grit sanding sponge.

I scrubbed the bowl with acetone on cotton pads to remove the remaining finish on the briar and to clean up the dust from all of the sanding of the fills. There was some beautiful grain that was showing through. The patches and fills actually looked much better.

I cleaned out the shank, bowl and airway in the shank and stem with alcohol, cotton swabs and pipe cleaners.

I sanded the stem with 220 grit sandpaper and a medium and fine grit sanding sponge being careful not to damage the stamping. I went over that area with a 1500 grit micromesh pad. I then use an antique gold oil based product called Rub and Buff to fill in the stamping. The next photo shows the finished rework of the gold in the stem stamp. I put the stem in place on the bowl to get an idea of the improvement that the repairs, fills and stem work had done. I wanted to see what the pipe would look like as I finished.

I wiped the bowl down with a final wash of isopropyl alcohol and then heated it so that I could give it a stain coat. I stained it with a dark brown aniline stain thinned by 50% with isopropyl alcohol. I applied it and flamed it. I reapplied the stain and flamed it again and then set it aside to dry.

When it had dried I gave it a light buff with a microfibre cloth to see what the colour looked like. It was still a bit dark to my liking but the coverage was good. The repairs and fills while visible looked far better than when I started.

I wiped the bowl down with alcohol on a cotton pad to make it a bit more transparent and make the grain shine through. It did not take much to coax the grain to the surface and highlight the beauty of the pipe.

I worked on the long stem. To clean it thoroughly I had to wrap pipe cleaners together to extend the length of the stem. I wet sanded it with 1500-2400 grit micromesh sanding pads to clean up the oxidation and scratches in the stem. I rubbed it down with Obsidian Oil afterwards and then dry sanded with 3200-4000 grit micromesh pads. I gave it another coat of oil and then finished sanding it with 6000-12000 grit pads. I gave it a final coat of the wax and set aside to dry.

At this point I laid the pipe on top of the current issue of the Pipe Collector and took a series of photos to show it before I buffed it.

I polished the nickel ferrule with a silver polishing cloth and gave it and the bowl several coats of carnauba wax. A light touch is imperative on the nickel as it will darken the buffing pad and then transfer to the bowl. I hand buffed the bowl and ferrule with a microfibre cloth. I buffed the stem with Blue Diamond polish on the wheel and then gave it several coats of carnauba as well. I buffed the stem with a clean flannel buff and then with the cloth as well. The finished pipe is shown below. It is repaired and serviceable for many years to come. Thanks for looking. Thanks for the challenge Warren.

What a Mess – A Vanguard Reg’d. Lumberman with a Bit of History

2 Replies

Blog by Steve Laug

I recently came across an EBay lot of bowls without stems and broken tenons still in the shanks. In the lot was one that intrigued me. It was the only one with a stem. The stem was short and tapered. It was very narrow and the button and slot made me think that it was old. The lot had the look of older English pipes but there was no information on the stamping. When the lot arrived in Vancouver, the stemmed pipe was stamped Vanguard over Reg’d on the left side of the shank. All other stamping, if there had been any, was lost. The bowls finish was gone. The colour was almost grey and there were spots all over this bowl and the others as can be seen in the photo below. From the third and fourth photo provided by the seller I could see that the shank was cracked and would need to be addressed. The rim appeared to be very thickly covered with lava and the outer edge had been damaged and rounded. The next photo shows the large crack that was present in the shank of the pipe. It had started to open and the edge of the shank where it met the stem had some nicks. When the box arrived the pipe was actually in worse shape than the photos had shown. The bowl rim was not all that was caked with tars. The bowl itself was almost 1/3 full of half burned tobacco, dottle that was rock hard and filled the bottom of the bowl. The cake on the rest of the bowl was not thick but was very hard. The finish was not only grey and spotty but was dented and rough to the touch. I could feel the ridge where the sides of the crack in the shank had separated. The rim edges were not only damaged and rounded but were also rough from banging out the burnt tobacco against something hard. The stem had tooth marks and chatter on both sides of the stem at the button. The button and slot were intact. The stem appeared to be as old as or older than I first thought. This was going to be a challenge to bring back to life but the age of it made it something I could not wait to tackle.

I took some close up photos of the state of the rim and cracked shank once the pipe arrived. It was a mess that is for sure. The rim and bowl were in bad shape and smelled awful. The shank crack was worse than I had imagined. The first photo of the cracked shank is from the top and the second photo is from the side.

I looked up the Vanguard name in Who Made That Pipe and found that there were two makers. There was a French maker and an English maker. The French pipe was made by Marchal, Rouchon 1907 and the English one was made by A. Oppenheimer/Bernhardt & Meyers. Given that I cannot be definitive as to which maker crafted this pipe. But the interesting thing is that the Marchal & Rouchon Cie which later became GBD France came under control of Oppenheimer in Great Britain. So you can see that though I may not know which one ultimately made the pipe the fact is that the two brands came together in 1902 when Marchal & Rouchon Cie sold out to Oppenheimer. I now have in my collection a pipe which may well have bridged the union of the two companies. The Vanguard thus could easily bear both the French and the English stamping. The lack of a “Made in…” stamp may well signify the years that the companies joined. That in itself made cleaning up and restoring this old-timer interesting for me.

I decided to start the clean up by reaming back the cake and cleaning out the dottle from the bowl. I used a PipNet reamer and started with the smallest head and worked up to the one that fit the bowl. I took the cake back to bare wood to check for damage to the inside walls of the bowl. With a pipe this worn I find that this is extremely necessary. I do not want any surprises after I have cleaned it up.

To repair the damaged shank I opened the crack as much as possible without making it worse and used a dental pick to push super glue into the crack. I pressed it together until it dried. I then used the sanding drum on the Dremel to take down the shank slightly so that a band would fit snugly on the shank and hold the crack tightly together. I pressed the band onto the end of the shank and took the picture below before I heated the band and pressed it into place. I heated the band with a heat gun and then pressed it against a flat surface until the band was in place on the shank. I pressed it onto the shank and then used a folded piece of sandpaper to clean up the edge of the band and shank. I left about 1/8th of an inch of the band extending past the shank to deal with the chipped and damage shank end. The stem would not have had a clean fit against the shank because of the damage. When the stem was in place it fit inside of the band against he shank and looked great.

With the band in place the shank was repaired and the tenon would no longer fit in the mortise. The contraction of the briar by the band cleaned up the crack and tightened up the loose fitting stem. I lightly sanded the tenon with a sanding drum on the Dremel and then by hand to get a snug fit in the shank.

I scrubbed the surface of the briar with acetone and cotton pads to remove the grime, spotting and remaining finish. There was some interesting grain under the grime.

The damaged rim surface and outer edge required that the bowl be topped. I used the topping board and 220 grit sandpaper to remove the damaged surface and sharpen the edge of the bowl.

I scrubbed the surface of the bowl down again with acetone and cotton pads to remove the dust and grime from topping.

I cleaned the inside of the shank and the stem with alcohol, cotton swabs and pipe cleaners. I used the drill bit from the Kleen Reem pipe reamer to clean out the airway from the mortise to the bowl. When I was finished I swabbed out the bowl with cotton swabs and alcohol and was pleased to find that the rank smell was gone. I sanded the bowl and stem with 220 grit sandpaper and a medium and fine grit sanding sponge to remove the tooth marks on the stem and scratches in the briar. I steamed the dents in the briar with a knife blade and wet cloth.

I sanded the stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I rubbed the stem down with Obsidian Oil between each grit and then continued sanding until I had worked through the lot of pads.

I wiped the bowl down with a light coat of olive oil and then sanded it with 1500-2400 grit micromesh pads and then continued through the rest of the grits of pads. I continued to polish the bowl with the remaining grits of micromesh.

I buffed the pipe with Blue Diamond polish on the wheel and then gave it several coats of carnauba wax. I buffed it with a clean flannel buff and then hand buffed it with a microfibre cloth. The finished pipe is shown in the photos below. It came out well for a pipe that potentially was made 108 years ago. Thanks for looking.

Procrastination & Restoration

3 Replies

Blog by James Gilliam of JSEC Pipes

What can I say, I really enjoy making pipes. The time I’m afforded for sitting in front of a sanding wheel, at the lathe and sitting at my desk doing detailed work are some of my most relaxing moments. The creative juices are flowing and at times I feel as if I’m breaking new ground with Shape X or Following Line Y, all the while the end goal is just to create a pipe that will become a cherished object of relaxation by its owner.

And here we are, writing up a little story for Steve’s Blog. It isn’t often that I venture down the restoration path, and when I get stumped I end up asking Steve a question or two. So, on to my story……. Our neighbor’s husband recently passed away and soon after the funeral she come over and gave me his pipes. I was elated that she even considered that and wanted to do them justice by addressing some minor cosmetic issues the pipes had.

The trio consisted of (from top to bottom): a Davidoff 152 Sandblasted Bent Billiard, a Charles Fairmorn – Made in Denmark Bent Egg, and a Charatans Make 4402DC Silver Banded Lovat. And as you can see by the first picture, they were enjoyed by their previous owner. They all had been taken care of but It had been a few years since they had been smoked. They were lovingly displayed in his corner of the living room. A remembrance, I guess, for those days when he did smoke his pipes. He still enjoyed them, just didn’t smoke them anymore.

The first order of business was addressing the oxidation on the stems. And I was stumped, as I’ve never seen oxidation this bad before. So after reading through the rebornpipes blog posts and contacting Steve I found what I needed to give the stems a little bath. I’m glad I sent Steve the email, as the bath that was enjoyed by all the stems made my efforts for oxidation removal rather easy. The best part is “most” of the stamping on the stems was savable, albeit on some a little fainter and not so pronounced as before. Had I just sanded the oxidation off, as I was inclined, there would be nothing else there. The oxidation really took its toll on the Davidoff stem, and about 1mm of diameter was no longer there after it was removed with a light sanding….. and I personally don’t find the new stem-shank junction off putting even though it was no longer flush.

The next issue to tackle was outer appearance. The Fairmorn Egg and the Charatan Lovat were the easiest to address as they simply needed an alcohol bath and scrubbing to remove some dirt and grime. A light sanding was in order for the Fairmorn Egg and that was followed by restaining. The best part was the Charaton retained it’s original color. A buffing with various pastes made them shine.

The Davidoff Bent Billard was a different story. Color wise It is, in my opinion, one of the ugliest pipes I’d seen. I scrubbed and scrubbed and scrubbed with alcohol to remove the underlying stain as best I could, to no avail. So I just decided to restain it a light brown….. and am glad that I did as the result came out rather nice…. At least I think so.

All in all, I’d say the pipes cleaned up rather well. Below is a picture of the complete set that I was gifted. My neighbor was more than elated to see them returned to their previous luster, and I was pleased that I could restore something from someone who meant so much to her.

The leather pipe stand still needs a foot/let on the rear left side, as the original fell off at some time in the past and the tobacco jar needs cork reapplied inside the top of the lid. It’ll get done, as the tobacco jar is the cat’s meow…..

Sorry it took so long to write up the story Steve and may you all have a joyful Christmas Season. Surround yourself with those you love, enjoy the time you are able to spend with them, and smoke a bowl in remembrance of those that were close to you and your family. Oh yea, and overlook Uncle Rufus this year… just chuckle and relight.

Merry Christmas and Happy New Year
James

Restemming & Restoring -Antique Egg & Claw Meerschaum

3 Replies

Blog by Steve Laug

My brother Jeff picked up a beautiful old Meerschaum pipe when he was in Austin, Texas. There was something about the old pipe that caught his eye and he wanted it. The patina of age was forming around the claws and the egg. The feathers on the bottom of the foot that held the claws was also colouring nicely. The browns of a well smoked meerschaum were changing the shadows around the bowl of the pipe. The shank also showed some signs of the colourng. It was almost a meerschaum collar out of which the feather foot extended. The cross hatched look of skin extended beyond the collar on the sides of the shank and the small claw held the bowl at the back. The bowl blackened but the cake was scraped clean other than a slight buildup around the top portion of the bowl. The rim was blackened with tars and there was some road rash on the top right side of the bowl toward the front. The tip of one of the feathers holding the claw on the front of the bowl also had a small chip but it had coloured like the rest of the feathers so it was blended in. The pipe itself was an old timer that was clear. The anomaly for me is that it should have had an amber stem. There is no way a pipe this age would have had a Lucite stem. The yellow Lucite stem looked that it had been adapted from a free hand pipe. The end had been drilled out to hold a replacement push tenon. It was set deep in the stem. The stem also had been counter sunk to cover the replacement threaded mortise in the shank. Instead of trimming it off to be flush with the end of the shank it stuck out about 1/8 of an inch or more. The stem maker had drilled the end of the stem so that with the tenon threaded in and the stem pushed into the mortise it would hide the mortise extension. The airway in the stem was pretty clogged and had blackened with tars. The stem had served the previous owner well. To my eye it just did not go with the either the age or the look of the pipe. It looked like two centuries had collided and joined to very different generations together with this stem and bowl. The shank itself was clean though the tars had stained the tenon. The airway in the shank was open and clean. It was as if someone had cleaned out the inside of the shank and bowl before putting the pipe up for sale at the antique shop. There were signs also that the bowl itself had been wiped down on the outside as the colouration bore signs of scratching from scrubbing the exterior with something like ScotchBrite pads. There were a lot of scratches and scrapes around the rim edges. Fortunately whoever had cleaned it had not removed too much of the patina. This pipe deserved some tender loving care to bring it back to life and restore the appearance to more of its stately form. The stem would definitely have to go and in its place an amberoid or amber coloured Lucite stem would have to be shaped to take its place.

I called Tim West at JH Lowe to talk with him about ordering a stem and what would look best with this old timer. Tim suggested a tortoise shell amber Lucite stem. He said the chocolate swirls in the material would look good with the patina of the old meer and as the bowl darkened more would continue to look good. I gave him the dimensions that I was hunting for and ordered a tapered stem. As usual Tim was quick in getting the materials I ordered shipped to me. It did not take long for it to arrive. I knew that it would be longer than I wanted and would need to be cut down and shaped but the colour would be perfect.

I got home from work on Monday to find Tim’s package had arrived. I opened it and took a picture of the new stem blank, the stem that I was retiring and the old bowl. You can see from the photo below that it is about an inch longer than the previous stem. The taper shape should work well with the pipe. Lots of drilling and shaping will need to be done before it fits the shank well. I am pretty limited in terms of a shop – no saws or power tools to make things simpler so I am left to resort to doing things by hand. I measured the length of the stem that I wanted and use a small hacksaw to cut off the excess stem material. Once it was removed I faced the newly cut end on my topping board to smooth it out and square it off. This is the hard way to do things I know but with careful attention to the verticality of the stem it is possible to get a smooth surface that is square to the shank end.

The push tenon and mortise was smaller than any that I had in my stash so I removed the push tenon from the old stem. It was not difficult to do as it was threaded and could be unscrewed. The mortise was threaded into the shank but extended beyond the end of the shank. I would need to sand that smooth and bevel it inward to give a good fit to the new stem. I took the next two photos below to show the two stems side by side and give an idea of the length.

With the length cut and the surface faced it was now time to start the drilling. I needed to drill the airway in the new stem to accommodate the diameter of the push tenon. Once it was drilled I would be able to thread it with a tap. The airway would also need to be drilled a second time to receive the collar on the tenon and give a flush fit with the stem end. I set up my cordless drill with a small drill bit to begin with and then worked up to the one that was the correct size for the tenon. I used a larger bit to countersink the end of the stem to take the collar on the tenon. The photo below shows the roughed in drilling of the stem. I would still need to clean up the edges of the countersink and also the roughness of the area that I would be using the tap on. I used needle files to bring the countersink into round, smooth out the edges and the airway. When I had finished with the airway I screwed the tenon into place and used a Dremel and sanding drum to begin smoothing out the mortise insert. I sanded the end of the mortise insert by hand to bring it to the same height as the rest of the shank end. I cleaned up the area around the tenon so that when I put the two pieces together I would have a pretty flush fit. I took the next photo to show the initial fit of the tenon in the stem. More sanding would need to be done to make the inner edges clean on the countersink. I pushed the stem into the mortise and took the photos below to have a look at the new stem and its fit on the pipe. There was still a gap in between the stem and the shank – it showed light so more work would need to be done to bring it flush against the shank. The overall look of the new stem worked for me. I like the tortoise shell look of the stem with the patina of the meer.

I carefully scraped the bowl with a pen knife to remove the small cake that was present in the bowl. It was more of a ridge than a full cake so I wanted to smooth out the sides of the bowl. I used the knife to begin the bevel on the mortise insert at this time as well. I would need to give it more of a slope to accommodate the tenon but it was getting there. I inserted a pipe cleaner in the stem and set up my heat gun. (I set it up on top of the dryer in our laundry room so forgive the socks and dishtowels in the background. I held the stem about 5 inches above the heat so that Lucite would not bubble (it did even at this height). When it was flexible I bent it to the same angle as the previous stem using an old rolling pin that I saved for this purpose. It took several time of heating it to get the angles correct so that the bend of the stem would match the curves of the bowl.

I put the newly bent stem on the pipe and took some photos so I could see if I got the angles correct. I find that the distance of a photo gives me clearer perspective than just holding it in hand.

With the fit of the stem and the bend roughed in it was time to work on the stem itself. The sharp edges of the taper and the thick button would need to be sanded and shaped. I would also need to get rid of the bubbles that happened when I heated and bent the stem. I started with emery cloth to quickly shape the button and take down the sharp edges. I also thinned the stem with the emery cloth and worked on the sides of the taper. I sanded it with 220 grit sandpaper to smooth out and further shape it and then followed up with a medium and fine grit sanding sponge.

I cleaned up the mess left behind by the stem sanding and worked on the scratches in the meer bowl and the heavy build up on the rim. I used 1500-2400 grit micromesh to sand the rim and the area of road rash on the top of the bowl at the right side. I also sanded the scratches along the claws to clean up the mess that had been left behind. I was careful to no sand too much so as to keep the patina intact.

I scrubbed the bowl and rim with a cotton pad and saliva to remove some of the grime and dirt left behind on the bowl. I used a sharp Buck Knife to clean up the bevel of the mortise insert so that the stem would fit snugly against the shank. I sanded and polished the stem with micromesh sanding pads- wet sanding with 1500-2400 grit pads and then dry sanding with 3200-4000 grit pads. I wiped the stem down with a little Obsidian Oil to give the final 6000-12000 grit micromesh pads traction in the final polishing.

I also polished the meerschaum bowl with the micromesh pads to clean up and minimize the scratches. Here is a photo of the bowl with the 3200-4000 grit pads.

I buffed the stem with Blue Diamond polish on the wheel and then gave it a light coat of carnauba wax. I hand waxed the bowl with carnauba and buffed it with a microfibre cloth to raise the shine. The finished pipe is shown in the photos below. I definitely like the look with the new tortoise shell stem. It just seems to fit the age of the bowl better than the free hand stem that came with it. Thanks for looking.

Restoring a White Cloud Imported Briar Pot

4 Replies

Blog by Steve Laug

The next pipe up for refurbishing is a small pot shaped pipe. It is stamped on the left side of the shank with the words White Cloud over Imported Briar. There are no other stampings on the right side and underside of the shank. I have looked for the brand in WMTP and found the name but that it is an unknown maker from the US. I also on PipePhil’s site and found no additional information. I also did some searching on the web for information and found absolutely no information on the brand. Do any of you know anything about it? Any information would be greatly appreciated. Thank you.

The pipe was in good shape underneath the thick coat of varnish. The stem was oxidized and dirty. The varnish on the rim was peeling and bubbling. There was damage to the rim in terms of darkening and potential burn. The bowl had some cake but it was bare wood at the bottom third of the bowl. The stamping was very clean and readable. There were some dings and fills on the bowl sides but nothing huge. They would clean up adequately. The metal tenon and stinger were a very interesting looking piece of plumbing. They were dirty and tarred. The inside of the shank and stem also had a lot of grime. The stinger was stuck in the tenon so it would need to be heated to be able to clean the airway in the stem thoroughly.

I took the close up photo of the rim and bowl to show the damage to the rim surface and the cake that was present. The next photo shows the stinger apparatus. It is a unique set up that is different from the collection of other stingers that I have here. The stem was slightly underclocked so I heated the tenon with a lighter and corrected the fit of the stem in the shank. I removed the stem and dropped the bowl in an alcohol bath to soak overnight. I wanted to loosen the varnish on the bowl and knew that while the alcohol would not remove it, it would soften it and make it easier to sand off. In the morning I removed the bowl from the bath and dried it off. The shiny coat of varnish was unscathed by the alcohol but I knew that it would be easier to remove. You can see the interesting grain on the bowl sides in the photos that follow. You can also see the nicks and fills that would need to be dealt with in the restoration.

I sanded the rim and the bowl with a medium grit sanding sponge to begin the process of removing the varnish. It worked well to break the seal on the varnish coat. Once that is done it comes off quite easily with acetone.

I needed to lightly top the rim to remove the burn mark and rounding on the front outer edge of the rim. It did not take much to clean up the rounded edge and give the rim a crisp profile.

I wiped the bowl down with acetone on a cotton pad and was able to completely remove the varnish coat. The alcohol had softened it and it came off very easily.

I heated the stinger in the tenon until I was able to wiggle it free of the airway. One side of the two prongs that held in place in the tenon was cracked so I repaired it and set it aside to dry. I cleaned out the shank and the stem with pipe cleaners, cotton swabs and alcohol. I sanded the stem with 220 grit sandpaper to remove some of the wavy marks from previous repairs to tooth damage. I sanded until the stem was smooth and then sanded it with a medium and a fine grit sanding sponge. I also sanded the bowl with the same sanding papers and sponges to minimize the dents and scratches in the finish.

I reamed the bowl with a PipNet reamer to remove the cake on the upper portion of the bowl.

I sanded the bowl and rim with micromesh sanding pads- wet sanding with 1500-2400 grit pads. I wiped the bowl down with a light coat of olive oil before proceeding to sand with 3200-4000 grit pads. I rubbed it down a second time and then sanded it with 6000-12000 grit pads. I buffed it by hand to see what the finish looked like at this point.

I sanded the stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and then rubbed it down with Obsidian Oil. I dry sanded with 3200-4000 grit pads and gave it another coat of the oil. I checked the stinger and for some reason there was some dark grime that appeared in the slot in the stinger. I cleaned it again with pipe cleaners before sanding some more with 6000-12000 grit pads. I gave the stem a final coat of Obsidian Oil and set the pipe aside to dry.

I buffed the pipe with Blue Diamond on the buffing wheel and then gave the bowl and stem multiple coats of carnauba wax. I buffed it to a shine with a clean flannel buffing wheel. When I finished buffing it on the wheel I took it back to the work table and buffed it by hand with a microfibre cloth. The finished pipe is shown in the photos below. It should deliver a good smoke to whoever adds it to their rack. The briar is certainly interesting to look at now that the finish has been stripped and the bowl polished. Thanks for looking. cloud41 cloud42 cloud43 cloud44

Repairing and Restoring a1929 Irish Free State Billiard

5 Replies

Blog by Aaron Henson – 11/29/15

I think the thrill of the hunt is part of what makes this hobby so enjoyable. Going into a new store or happening upon a pipe in an unlikely place, never knowing just exactly what you are going to find and always keeping a lookout for that forgotten gem.

This past summer I was on vacation with my family in Seaside, Oregon. Between Seaside and Astoria I visited 14 different antique stores and only two had any pipes at all. And of those, they were all on the pricy side; too rich for me.

Partly on a whim and partly out of desperation, I went into a second-hand store that I had passed by several times. It was more “junk” than “antique” and of course that is where I made my score although I didn’t think so at first. Three pipes: the first was a non-briar volcano with “Italy” stamped on the bottom, the second was a Medico that was in such bad shape it could only be used for parts but the third was intriguing with a silver band. I could not read the markings for all the filth on the pipe. I negotiated with guy behind the counter and walked out will all three for $15. It was clear that this had been a very nice pipe in its day. The wood grain that could be seen through the grime was beautiful and the Army Style push stem I thought gave the pipe a classy feel. When I got it back to the house and looked it over in better light, I noticed that the band had been rotated on the shank so the writing was upside down and in the dim light of the store I could not read it. Now I could see that it clearly said “Peterson” and “Dublin” stamped in the silver band.

A Peterson, my heart skipped a beat. I was well aware of Peterson’s long history of making quality pipes and now I had picked up an early model for 5-bucks!

The bowl had a good build up of cake and a fair amount of unburned tobacco in the bottom. Some build up of tars on the rim but otherwise seemed to be in good condition. The shank had clearly been broken, however and the glue used for the repair was spread all over one side of the bowl. The stamping on the band, as stated before, were worn and not very readable. The stem was oxidized and had a hole in the top near the button. This must have been a favorite pipe of the previous owner.

When I got home from vacation, I tried to understand the symbolic hallmarks on the band. Not being familiar with Peterson marking I sent a picture to Steve Laug to ask his opinion. Steve very graciously referred me to his Peterson expert, Mark Irwin. With Mark’s help I was able to understand Peterson’s hallmarking and dated the pipe as 1929 – placing it in the Irish Free State era: 1922 – 1937. At least, that was my interpretation of the third hallmark, an “O”.

I began by reaming out the cake with a Castleford reamer and took the interior back to bare wood. There were some burn marks under the tar on the rim so I elected to top the bowl with some 220 grit paper laid on the flat work bench. Next I heated the band with a flame and then using leather jawed pliers and carefully rotated the band back into correct alignment. The outside of the bowl I wiped down with a cotton pad soaked in acetone. This removed the grime and the glue. I had been worried that the glue was covering a crack in the bowl but it turned out that the person doing the shank repair had just been sloppy. The glue came away and revealed pristine briar underneath. In just the right light, I also could see a very faint IRISH FREE STATE stamped into the bottom side of the shank – Confirmation! The break between the bowl and the shank had been complete. I could see the seam all the way around the shank but it had been a clean break. There were no gaps, rounded edges nor missing pieces; so far, so good.

At this point I turned my attention to the stem. I put the stem to soak in a mild chlorine bath to raise the oxidation. A light sanding with some worn 400 grit paper removed the oxidation completely. I picked the loose material out of the hole, made backing plug out of toothpicks and slipped it into the airway. This would hold my patching material in place. Next I mixed up some StewMac black super glue with some activated charcoal powder and worked it into the hole with another tooth pick. I set the stem aside to cure over night.

When I came back to the stem I sanded down the fill with 220 grit paper. The plug blended nicely and I proceeded to polish the stem with 1500 – 12000 micromesh pads. Cleaning the inside of the stem was quite simple, four of alcohol soaked pipe cleaners (2 bristled and 2 soft) took care of the insides and the stem was done. Returning to the stummel, I began to work the bowl-shank joint back and forth with ever increasing force. I caught myself holding my breath, afraid of breaking the pipe beyond repair but dismissed that thought as fear of the unknown and pushed on. Eventually the crack began to open up and the shank and bowl were separated. I was surprised to see that the original repair had included two small brads – or pins – set on either side of the air hole to strengthen the break. Since the brads were already in proper alignment I decided to reuse them in my repair. After some research, I settled on the J-B Kwik Weld as my epoxy of choice. Its resistant temperature is less than that of original J-B Weld (300 vs 550 degrees); however, I do not think the shank should reach 300 degrees during a smoke. But the real advantage in my minds was that the set time is only 6 minutes compared to 4-6 hours. I didn’t want to have to come up with a way to hold the two parts together for several hours and risk the parts slipping.

In order to keep the airway clear during the repair, I pushed a pipe cleaner through the airway before smearing the epoxy on the both surfaces with a tooth pick. With the clock running on the set time, I pushed to the two parts together using the old brads as alignment pins. Looking back I think it would have been better if I had only used one of the pins. The fit was tight and I was fighting against the pins to get the two parts tight together when the time ran out on the epoxy. I was left with a larger gap between the pieces than I thought was right; I had been hoping for a flush fit. Before setting the pipe aside to cure I wiped off the excess epoxy and removed the pipe cleaner. I let the pipe sit overnight and the next day I used a dental pick to remove some of the epoxy from the gap between the stummel and bowl. The gap was very small, less than a 1/32 of an inch on top and near flush on the bottom. When the crack was as clean as I could get it, I filled it with briar dust and placed drops of clear super glue on top to hold the dust in place. When the super glue dried I smoothed out the repair with 220 grit sand paper. There were some minor dents in the bowl and I decided to steam them out by wrapping the bowl with a damp terry cloth rag and going over the rag with a clothes iron set on high. If you used this method I would advise keeping your figures well clear of the iron. Speaking from personal experience, you don’t have to be very close to the iron get burned by the steam. Fortunately, I did not drop bowl!

I sanded the entire bowl with 400 – 2000 grit paper to remove all the dents and scratches but being sure to stay clear of the marking on the shank. The markings were faint but I wanted to preserve as much of them as I could.

The bowl had beautiful grain and I wanted to use a light brown stain to highlight it. I used one part Fiebing’s light brown mixed with 2 parts isopropyl alcohol applied with a cotton swab in layers until the color looked just right. I flaming each layer and wiped off the excess with a cotton pad moistened with alcohol.

The next to last step was to polish the sterling silver band. For this I tried a new technique that I had recently learned on this blog using a small amount of cigar ash and saliva. I was careful not to polish too much – or at all – around the hallmarks. The final step was a trip to the buffer for three coats of carnauba wax on the briar and stem. I hand applied a light coat of Walker Briar Works carnauba wax sealer on the silver band and I buffed the pipe with a micro fiber cloth to bring up the shine.

Bringing a Dr. Grabow De Luxe 9704 Bent Billiard Back to Life

4 Replies

Blog by Steve Laug

I just finished cleaning up the last of the pipe I picked up from the antique malls while I was in Idaho Falls. It is a little Dr. Grabow bent billiard. It is stamped on the left side of the shank Dr. Grabow over De Luxe over Imported Briar. On the right side near the stem shank union it is stamped with the shape number 9704. From what I can find on the Grabow shape charts the 04 shape is the bent billiard. This one was in rough shape. The finish was basically worn off and the bowl had spots of sticky grime on the sides and shank. There were also spots of paint on the shank and bowl. There were scratches all over the bowl. There were a lot of small fills on the right side of the bowl and the top of the shank as well as a large one on the lower part of the front of the bowl. Because of the missing finish these stood out. The top of the rim had a buildup of tars that looked flaky and hard. The bowl had a thick cake that made it impossible to see if the inside of the rim was in decent shape. I would need to ream it back to be sure. The stem was oxidized and the dirty with light tooth chatter on the underside near the button.

I took a close up photo of the top of the rim to show what I had to work with in cleaning up the bowl and rim. When I took the stem off the pipe it had the usual Dr. Grabow shovel stinger apparatus. This was a little unique in that it was not inserted into the metal tenon but was an integral part of the tenon. The two were cast together which made removing it impossible. It was covered in tars and in a tobacco coloured lacquer that was rock hard. The next two photos show the stamping on both sides of the shank. The right side shows the clear shape number stamp and the left side the Dr. Grabow stamping. The Imported Briar stamping is weak but visible.

I reamed the bowl back to bare wood with a PipNet reamer. I started with the smallest cutting head and worked my way up to one that was the same diameter as the inside of the bowl. Once the cake was cleaned out I used a pen knife to clean up the small ridge that shows up in the second photo below.

I used a sanding sponge to lightly top the bowl. The tars and lava on the top were hard and this was the way I chose to remove it without damaging the finish to the rim. I worked on it until the rim was clean and smooth. It would still need to be scrubbed to remove the darkening.

I scrubbed the rim and the bowl with acetone on a cotton pad to remove the grime and oils left in the finish. I scrubbed until the rim and bowl were clean. I scrubbed the shovel stinger with 0000 steel wool to remove the buildup on the aluminum and polish it at the same time.

I cleaned out the shank with alcohol, pipe cleaners and cotton swabs until it was spotless. I then worked on the stem. It was made a bit more difficult with the built in stinger but I was able to get it clean with a bit of effort. With the inside clean I sanded the bowl and rim with 220 grit sandpaper and a medium and fine grit sanding sponge to clean up the finish. I was able to remove the darkening on the rim and also the dark spots on the sides of the bowl.

I screwed the stem back on the shank and then sanded the stem with the same sandpapers as I had sanded the bowl. I removed tooth chatter and the calcification on the first inch of the stem. I worked on the slight tooth marks on the button itself and cleaned them up. The pipe was beginning to take shape. Much more sanding would need to be done to the bowl to remove all of the scratches left behind by the sandpaper and a lot of polishing would need to be done on the stem before the pipe was finished.

I rubbed the bowl down with olive oil so that I could wet sand the finish and work out the scratches.

I sanded the bowl with micromesh sanding pads and the olive oil until I was able to remove the scratches. I started with 1500-2400 grit pads and sanded until the scratches were minimized and then rubbed it down with olive oil once again before sanding with 3200-4000 grit pads. Each successive micromesh pad brought more of a shine to the briar. The fills became smooth and blended into the briar better and began to disappear into the briar as the scratches around the edges were smoothed out.

I gave it a final rub down with oil and then finished sanding it with the last three grits of micromesh – 6000-12000. The bowl was smooth to the touch and had a shine to it that once was buffed and waxed would glow.

I sanded the stem with micromesh sanding pads – wet sanding with 1500-2400 grit pads and then rubbing it down with Obsidian Oil. I continued to dry sand with 3200-4000 grit pads and gave it another coat of the oil. I finished by sanding it with 6000-12000 grit pads and then gave it a final coat of oil and let it dry.

I buffed the pipe on the wheel with Blue Diamond polish and then gave the bowl and stem multiple coats of carnauba wax. I buffed it with a clean flannel wheel to give it a shine and finished by buffing it with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. It is a beautiful old Grabow that has a lot of life left in it. Whether I keep it or pass it on to someone else it should last much longer than I will. It should continue to give companionship to whoever’s rack it graces. Thanks for looking.

ADDENDUM: I received the following message on FaceBook from Christopher Chopin. It adds much to the information on this pipe so I add it here:

A favorite shape. Nice job as always Steve. And yes, 04 is the shape code, 97 was the finish code for deluxe. Also 92 and 98, there was more than one De Luxe, and 97 was the natural variegated finish. Dating on that if I’m not mistaken is between 1944 and 1953, at which point the spade was rotated so that the tip pointed to the bowl instead of the mouthpiece, after the company was purchased by HL&T. That is a true Linkman’s grabow, they just discontinued the Linkman’s stamp in ’44. I suspect it’ll find a place in your regular rotation.

Share this:

Share this:

Share this:

Share this:

Share this:

Share this:

Share this:

Share this:

Share this:

Share this: