Tag Archives: bite marks

This Greenwich House Antique Imported Briar Crowned Pot Turned into a Nightmare

1 Reply

Blog by Steve Laug

Sometimes when I start working on a pipe there is can be a sense of gloom or expectant trouble. That was the case with this one. I thought it would be a straightforward clean up and restoration. Little did I know what lay ahead for me in this restoration. Time would tell and I would share it here with you my readers. It started as usual. I recognized the brand on this pipe but could not remember any of the details. Jeff picked this pipe up from an antique store in Ogden, Utah, USA back in 2019. It is stamped on the left side of the shank and reads Greenwich House [arched over] Antique and on the right side Imported [over] Briar. It was the Greenwich House tag that grabbed my attention. You know how sometimes a name just sits on the edge of your memory beyond your reach but you still know it? That is what this name did to me. The finish is quite dirty with a cake in the bowl and lava overflow on the rim top. The worm trails on the sides and base reminded me of a Custom-Bilt but a bit more smooth. The crowned rim top was more elegant. The saddle style stem was old vulcanite and other than deep tooth marks it was quite clean, Jeff took some photos of the pipe before he started. He took close up photos of the rim top, bowl and stem to give a better picture of what he was seeing as he prepared to clean it up. You can see the cake in the bowl and the lava on the rim top. The inner edge appears to be burned and damaged but it was hard to tell for sure. The stem had some deep tooth marks on both sides just ahead of the button and some light calcification at the sharp edge.Jeff took his characteristics photos of the bowl sides and heel to give a clear picture of the grain around the bowl and the style of the worm trails carved into the sides and heel. It is a nice piece of briar.The stamping was readable though a little faint on the left side of the shank. It read Greenwich House arched over Antique on the left. On the right side it was very clear and read Imported [over] Briar.I turned first to my blog on a previous restoration of a Greenwich House pipe. I had worked on one that was stamped Thoro-Kleen, a metal pipe (https://rebornpipes.com/2016/02/24/a-piece-of-art-deco-greenwich-house-thoro-kleen/). I read through that blog and have included a pertinent piece of information on the brand below.

According to Pipedia (https://pipedia.org/wiki/Thoro-Kleen) the Greenwich House Thoro-Kleen was a metal pipe system from the same family as the Roybrooke, Comet, and Original Gridiron pipes, and parts from all are believed to be interchangeable. The pipes were sold by the Greenwich House Corporation, located in 1947 at 939-M 8th Avenue, N.Y. 19, N.Y…

From that I knew it was an American Made pipe that had been carved for or by a company known as Greenwich House Corporation in New York City.

I turned to the listing of American Brands on Pipedia to see if there was a listing for the Greenwich House itself (https://pipedia.org/wiki/American_Pipe_Brands_%26_Makers_G_-_H). I found that there was not an article but the list of makers identified the brand and said that The Antique was made of Aged Algerian Briar. One more piece fell in place. The pipe I was working on was stamped Antique so I now knew the source of the Imported Briar.

But I still wanted a bit more information so I did a Google search and was taken to pipes made by Greenwich House on smokingpipes.com and other sites. Worthpoint, an auction site had several and also had one stamped Antique (https://www.worthpoint.com/worthopedia/vintage-greenwich-house-carved-1992675965). I have included the description from the sale item below as it is quite descriptive of the pipe in my hands.

Vintage Greenwich House Carved Antique Aged Algerian Tobacco Pipe. Good condition. Measures about 6.25″ long.

It is similarly stamped as mine and also similarly sized. Now it was time to work on the pipe itself. Jeff had cleaned up this nicely grained Pot with his usual pattern. He reamed the bowl with a PipNet pipe reamer and then cleaned up the inside of the bowl with a Savinelli Fitsall Pipe Knife. He scrubbed the exterior of the bowl and shank with Murphy’s Oil Soap and a tooth brush to remove the grime on the rim top and bowl. He cleaned the internals of the shank and stem with pipe cleaners, cotton swabs and alcohol until the airways were clean and the pipe smelled fresh. The pipe looked much better once the bowl and stem were clean. He scrubbed the stem with Soft Scrub to remove the oxidation and then let it soak in Before & After Pipe Stem Deoxidizer. He rinsed it with warm water when he took out of the soak. Before I started my part of the work I took photos of the pipe. I took close up photos of the bowl and the rim top to show the condition. The photo clearly shows the burn damage to the inner edge and the rim top at the back of the bowl. You can also see the roughening of the rest of the inner edge and rim top. It was going to take some work to bring it back. I also took photos of both sides of the stem to give a sense of the condition of both sides at the button. There is deep tooth marking and damage on both sides ahead of the button. I took a photo of the stamping on the sides of the shank. It was readable but was more faint on the left than the right side. It read as noted above.I removed the stem from the shank and saw to my chagrin a stinger. I fiddled with it a bit to see if it was pressure fit or screwed into the tenon. There was no give to it. (This portends what is ahead, keep reading.) I set the stem down with the bowl and took a photo to give a general look at the proportions of this pipe.I started work on this one by using a folded piece of 220 grit sandpaper to clean up the inner edge of the bowl and the rim top at the back. I was able to clean and reshape the bowl by slowly working through the process. So far the restoration was going well.I polished the bowl and rim top with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiped down the bowl after each sanding pad. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips and a horse hair shoe brush to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The Balm did its magic and the grain stood out.   So far so good! I filled in the deep gouges on the top and underside of the stem and set it aside for the repairs to cure.After the repairs cured things took a horrible turn! If you have read this blog for long you know how much I dislike metal stingers. I find that they indeed condense moisture and fill the shank with horrendous muck. Soooo… I decided I would try to remove this one and give the stem a thorough cleaning. I have found that most stingers are either threaded and screwed into the tenon or are pressure fit. Either way a little heat loosens the glue or gunk that hold it tight and it is easily removed.

Well… the heat did absolutely nothing with this one. It did not twist or wiggle free. It was solid with or without heat… or cold for that matter. I was frustrated at this point and tried to pull it with pliers and the “wicked” thing snapped off! Now that usually does not matter either. I can easily drill it out with a small bit.

Again not so!! The remaining tube went well beyond the saddle on the stem. I drilled and drilled then filed the edges to smooth it out. At this point I should have just left it. But I DID NOT DO THAT. NO! I tried to pull out the remnant of the tube with a small file. And then a chunk of the tenon cracked off. You can see the offending tube in the tenon stubbornly laughing at me. Arggh… This was becoming much more of a  problem. Each step I took to remedy it made it actually worse. Now I would need to cut off the remaining tenon and the drill the stem and make a new tenon for it. OH MY! THIS IS NOT WHAT I WANT TO DO!!

I got out my hacksaw and carefully cut all the way around the broken tenon. I purposely did not cut the tube as I wanted to see how far into the stem it actually went. I pulled it out with a pair of pliers and took a photo of the length of the offending tube once it was free of the airway. You might laugh at this point and I invite that. This was a lot of work to go to just to clean out the airway in the stem. But now I could replace the tenon. I went through my tenons and had one that was a close fit to the shank of the pipe. I would need to drill out the stem to take the threaded replacement tenon but I was hoping that this part would proceed without more things going awry. I started drilling with my cordless drill and a bit slightly larger than the airway in the stem. I continued going through various bits up to ¼ inch which was the size I would need to receive the threaded tenon end with some modifications. You will notice the repairs to the deep tooth marks still have not been smoothed out.I modified the threaded tenon with a Dremel and sanding drum. I removed the should on the middle of the tenon and reduced the diameter of the threaded portion so that I could glue it in place in the stem. I cleaned up the edge between the thicker portion and the threaded portion with a flat rasp to make the fit smooth when inserted in the stem. I inserted it in the stem and took a photo.Before gluing the tenon I the stem I put all the parts together to make sure that everything lines up correctly. It looks good so I take photos to show it at this point in the process. With the alignment correct I coated the threaded end of the tenon with black super glue and pushed the tenon in place in the stem. I set the stem aside to let the glue cure and went and had a cup of coffee with Irene. I needed to lick my wounds a bit on this whole mess!After coffee I went back to the stem to clean up the repairs on the top and underside of the stem. I flattened out the repairs with a flat file to begin to blend them into the surface. I followed that up with 220 grit sandpaper to further blend it in. I started polishing it with 400 grit wet dry sandpaper. I polished the stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. I gave it a final coat of Obsidian Oil and set it aside to dry. While I liked the look of the new stem on the shank it felt like it was missing something to me. I really wanted to give it a special touch that would set it apart and make the look spectacular. I went through my band collection and found a perfect 14K Gold band that would do just what I wanted. I took down the end of the shank to enable a snug fit. I heated the band with a lighter and pressed it onto the shank end. I finally finished this nightmarish restoration of a pipe that should have been quite simple. The Greenwich House Antique Import Briar Crowned Pot with a vulcanite saddle stem is a great looking pipe now that everything came together. The briar around the bowl is clean and really came alive. The rim top looks much better than when I began. The rich brown stains gave the grain a sense of depth with the polishing and waxing. The grain  on the smooth portions really popped and the worm trails carving look good as well. I put the vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine.

The finished Greenwich House Antique Pot is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The weight of pipe is 2.29 ounces/65 grams. It is much more beautiful in person than these photos can capture. I will be putting it on the rebornpipes store soon. Look for it in the American Pipe Makers section. If you would like to add it to your collection let me know. This is another pipe that has the possibility of transporting the pipe man or woman back to a slower paced time in history where you can enjoy a respite. Thanks for walking through the restoration with me.

Life for a Beautifully Grained Royal Saxon Canadian

Leave a reply

Blog by Steve Laug

This pipe was bought from an online auction on 04/04/19 in Wilkes Barre, Pennsylvania, USA. It is a nicely grained Canadian with a Sterling Silver shank band and a vulcanite taper stem. The bowl had a thick cake in the bowl and burn damage all around the inner edge of the bowl. There is also a burn mark on the outer edge on the front top and left edge of the bowl. There are some nicks in the left side toward the front of the bowl. The finish is very dirty with a lot of debris and grime ground into all the way around. The Sterling Silver band is oxidized and tarnished. The stamping on the pipe is on the top of the shank and reads Royal Saxon. There is no other stamping on the briar. The band is stamped Sterling Silver on the top side. There does not appear to be any cracks in the shank so it is solely for cosmetic purposes. The stem is oxidized and has tooth marks on the top and underside ahead of the button. Jeff took some photo of the pipe before he started his work on it. Jeff took photos of the bowl and rim top to show the cake in the bowl and the burn damage on the top and on the beveled inner edge of the bowl. He also took photos of the stem to show the tooth marks and chatter on the oxidized stem. He took photos of the bowl and heel to show the condition of the finish. You can see the small chip/nick on the front middle of the bowl on left side. It is solid but it is visible at this point.Jeff took photos of the stamping on the top of the shank and the silver band. They read as noted above and were in excellent condition. I checked on both Pipephil’s site and Pipedia for information on the Royal Saxon brand and neither site had any information. I checked on Who Made That Pipe and again found no information. So I Googled Royal Saxon Smoking Pipes and found information on Worthpoint and on Smokingpipes.com that said the pipe was an Italian Made pipe. They showed a variety of shapes – smooth, rusticated and blasted that all were stamped exactly like the one I am working on. Thus I know that the pipe is an Italian Made pipe but I have no idea who made it.

I did a bit of digging on Savinelli seconds but no Royal Saxon was listed as made by them. I also checked with Lorenzo as they made a lot of seconds lines and there was no listing for the Royal Saxon so I was at a dead end. Oh well – now it was time to work on the pipe.

Jeff had cleaned up this nicely grained Royal Saxon with his usual pattern. He reamed the bowl with a PipNet pipe reamer and then cleaned up the inside of the bowl with a Savinelli Fitsall Pipe Knife. He scrubbed the exterior of the bowl and shank with Murphy’s Oil Soap and a tooth brush to remove the grime on the rim top and bowl. He cleaned the internals of the shank and stem with pipe cleaners, cotton swabs and alcohol until the airways were clean and the pipe smelled fresh. The pipe looked much better once the bowl and stem were clean. He scrubbed the stem with Soft Scrub to remove the oxidation and then let it soak in Before & After Pipe Stem Deoxidizer. He rinsed it with warm water when he took out of the soak. Before I started my part of the work I took photos of the pipe. I took close up photos of the bowl and the rim top to show the condition. The photo clearly shows the burn damage to the inner and outer edge of the bowl at the front. You can also see the roughening of the rest of the inner edge and rim top. It was going to take some work to bring it back. I also took photos of both sides of the stem to give a sense of the condition of both sides at the button. There is tooth marking and damage on the top of the button on both sides as well as ahead of the button. The silver band is shown in the photos and is clearly tarnished.I took a photo of the stamping on the shank and silver band. It was readable but had some faint spots. What was interesting to me is that in the first photo there is also a stamp that shows up on the top side of the stem that I had not seen before. It is almost like a Old English “C” but I am not sure.I removed the stem from the shank and took a photo of the pipe to give a sense of the proportions of the whole.The first photo below shows the condition on the rim top, outer and inner edge before I started reworking it. I took a photo of the wooden ball that Kenneth gave me that I use in beveling a rim edge. I started work on this one by topping the bowl to take care of the deep burn marks on the top at the front of the bowl. I then reshaped the top and the bowl edges with a piece of sandpaper on a wooden ball. The ball and sandpaper helped clean up the beveled edge and blended in the burn and cuts in the briar as well as bring the bowl back into round. I used a folded piece of 220 grit sandpaper to further shape the bowl. Once I had it smoothed out and shaped I gave it an initial coat of stain with an Oak Stain Pen to match the stain colour around the bowl and shank. Lots of polishing yet to do but it is looking better. The burn mark on the top could not be totally removed without changing the profile of the pipe so I minimized it and it is significantly better. It will just be a permanent part of the pipe’s story.I polished the bowl and rim top with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiped down the bowl after each sanding pad. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The Balm did its magic and the grain stood out. I polished the Sterling Silver band with a jewelers cloth to remove the tarnish and protect it from further tarnish. I set the bowl aside and turned my attention to the stem. I wanted to see if I could use some acrylic white fingernail polish to bring back the stamp to readability on the top of the stem. I applied the acrylic and let it cure. I scraped it away and it was a little readable but not clear enough.I “painted” the stem with the flame of a lighter to try and lift the tooth marks on the stem and button surface. While it did some lifting there were some deeper ones that remained. I filled them in with clear CA glue and set it aside to cure. Once it cured I flattened them out with a small file and recut the button edge. I sanded them with 220 grit sandpaper and started the polishing with 400 grit wet dry sandpaper. I polished the stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. I gave it a final coat of Obsidian Oil and set it aside to dry. This nicely grained Royal Saxon Canadian with a Sterling Silver Band and a vulcanite taper stem is a great looking pipe now that it has been restored. The briar around the bowl is clean and really came alive. The rim top looks much better than when I began. The rich brown stains gave the grain a sense of depth with the polishing and waxing. The grain really popped. I put the vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Royal Saxon Canadian is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 1/8 inches, Chamber diameter: ¾ of an inch. The weight of pipe is 1.13 ounces /32 grams. It is much more beautiful in person than these photos can capture. I will be putting it on the rebornpipes store soon. Look for it in the Italian Pipe Makers section. If you would like to add it to your collection let me know. This is another pipe that has the possibility of transporting the pipe man or woman back to a slower paced time in history where you can enjoy a respite. Thanks for walking through the restoration with me.

A Fun Restore of a Nino Rossi 1886 Classico in Shape 992

1 Reply

Blog by Steve Laug

The next pipe is a bit of a mystery to Jeff and me. He keeps a spread sheet and photos of pipes that we pick up and it goes back to 2016 I believe. He has gone through that and cannot find this pipe on the record. However, we both remember finding it. I wonder if it is not on that we found on a trip that Irene and I made to Oregon and met Jeff and Sherry there. We stayed with them and Jeff and I did a bit of pipe hunting. I guess at some level we will never know for sure. I remember that when we saw it we both were struck by the uniqueness of the pipe. It really is a beauty that even the small fills around the bowl do not detract from.

The pipe was quite clean. It has all the marks of Jeff’s clean up work. The bowl is reamed and insides cleaned. The finish is very clean and the rim top and edges look very good. There is no damage on either one. The shank has an interesting joint mid shank. There is a tarnished brass spacer between two sections and each is stained slightly different. The bent saddle stem appears to have been deoxidized as it is also clean and relatively free of oxidation. There are light tooth marks and chatter on both sides at the button. It is stamped with the signature of Nino Rossi on the left side of the shank. Directly under that is the number 1886 which appears to me to be a year. On the left side of the saddle stem it has ROSSI in a oval logo inset. The right side of the shank is stamped Classico. On the underside of the shank it bears the shape number 992 followed by the stamp ITALY stamped vertically at the shank stem joint. It really is an interesting looking pipe. I have included photos of the pipe before I started to work on it.The rim top and inner and outer edges were in good condition. The stem surface looked very good with some light oxidation remaining and some tooth chatter and marks on both sides ahead of the button. I took photos of the stamping on the left/right and undersides of the shank. The stamping was clear and readable. The left side of the taper stem had a ROSSI oval  logo inset in vulcanite.  I removed the stem and took a photo of the pipe to give a sense of the beautiful grain on this well shaped Bent Billiard. I turned first to Pipephil’s site to see what I could learn about the brand as generally the site gives a good summary (http://pipephil.eu/logos/en/logo-n1.html#ninorossi). I quote the information from the side bar below and did a screen capture of the pertinent section on the site. I have also outlined a picture on the screen capture that is stamped like the pipe I am working on.

Brand founded in 1886 by Ferdinando Rossi senior. He estabished a factory in Barasso, 5 miles away from Varese. The pipes production by the 850 employees reached 50,000 pipes/day in 1936. Ferdinando Rossi junior headed the company from 1946 until close down in 1985.   I turned to Pipedia to read the more complete history of the brand and learn what I could about a possible date for this pipe (https://pipedia.org/wiki/Rossi). First I wanted to understand the 1886 stamp on the shank under the signature stamp. I found that it was the year that the company acquired land and opened Fabbrica di Pipe di Radica Rossi.

He acquired a large area of land in Barasso in the province of Varese and founded the Fabbrica di Pipe di Radica Rossi in 1886. For sure there was no lack of skilled workers and Rossi personally recruited 30 craftsmen of different occupations from the environment to get started. After a few years the enterprise had developed well and entered into export trades. In 1892 e.g. the ledgers registered the first pipes shipped to Brazil.

I quote a summary section of the article below.

From, approximately, Twenties, Rossi pipes were marked with “FRB” (Fratelli Rossi Barasso) or “MFRB” (Manifattura Fratelli Rossi Barasso), into an oval and above “OLD BRIAR” (or similar – sometimes, there was also “MFD. BY ROSSI”, as “Manufactured by Rossi”); on the stem, there was generally the “R” letter in circle. However, “FRB OLD BRIAR” was mantained for the “traditional pipes” (for cheap models – see below), surely, to Sixties.

From, approximately, the fiftieth anniverary (1936), pipes were marked with “Rossi” (in cursive font), with model name just under it; on the stem, there was “ROSSI” (for expensive models like “extra”, which had the best quality; “racine”, which was rusticated by hand; “extra grain”, which was accurately sandblasted; “super”, which had the best briar selection, and a limited production; “fiamma”, which was the best selection of Sardinia and Greece briar, and a very limited production) or “R” in circle (for unexpensive models like “standard”, “grana” and “FRB”).

From, approximately, Seventies, until 1985, Rossi pipes were marked with “ROSSI”, into an oval (sometimes there was also “ITALY” on the shank); on the stem, there was “ROSSI”. In these years, appeared the signature “Nino Rossi” (in cursive font): he was the last heir of the factory.

When Savinelli took back the production, it is said that first pipes had a twinbore mouthpiece, with “ROSSI” on the stem, and they were marked with “ROSSI” on the shank. Today most of them had 6 mm or 9 mm adapter (also, for the most part, the stem was made by methacrylate, always with “Rossi” on the side).

The section I have highlighted in Blue above gave me what I was looking for regarding this pipe. It is one that was clearly made between the 70s and 1985 when the company closed. It is stamped as described in the highlighted paragraph. Now it was time to work on the pipe.

As I examined the spacer between the two parts of the shank it became clear that it was oxidized brass. I started there with my work on this pipe. I lightly sanded it with a 1500 grit micromesh sanding pad to break up the oxidation and then polished it with a jewelers cloth that removes oxidation and preserves against further oxidation. It is a pretty neat looking addition with the polished brass. I took some photos of the pipe to show the spacer. I polished the bowl and the rim top, sides and shank with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiping it down after each pad with a damp cloth. I carefully avoided the stamping on the sides of the shank so as not to damage it. The fills on the side of the bowl and shank are visible but oddly do not bother me too much. It is still a nice looking pipe. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides, rim top and shank end with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The grain really stood out clearly. While the fills are still evident they seem to blend in better at this point in the process.   I set the bowl aside and turned my attention to the stem. I heated the stem with a lighter flame to lift out the tooth marks (forgot to take photos). They were too sharp and essentially were cuts so they did not lift at all. I filled them in with clear CA glue and set them aside to cure. Once they cured I flattened the repairs out with a small flat file. Once the repairs had cured I sanded them smooth with 220 grit sandpaper to blend them into the surrounding vulcanite. I started the polishing with 400 grit wet dry sandpaper. I worked over the stem with micromesh sanding pads – 1500-12000 grit pads. I wiped the stem down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This well made Nino Rossi 1886 Classico 992 Bent Billiard with a briar shank extension and a vulcanite saddle stem is a great looking pipe now that it has been restored. The rich reddish, brown finish that was used came alive with the polishing and waxing. The brass spacer was a great touch in the middle of the shank. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Nino Rossi Classico is a beauty with combination of great grain and rich stain. Even the fills do not detract from its appearance. It fits nicely in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 1/8 inches, Chamber diameter: 5/8 of an inch. The weight of the pipe is 58 grams/ 2.01 ounces. If you are interested in adding this pipe to your collection I will be adding it to the rebornpipes store shortly. It will be in the Italian Pipe Makers section. Send me a message or an email if you are interested in purchasing it. Thanks for reading this blog and my reflections on the pipe while I worked on it. As always there are more to come.

Another Beautification – This time a Bertram Washington DC Grade 60 Pot

Leave a reply

Blog by Steve Laug

The next pipe on the work table is another on that came to me from one of our estate purchases. Between us we pick up quite a few pipes for restoration. I try to work them into the restoration queue so that I can keep them moving. We picked up over 120+ Bertram pipes from an estate that a fellow on the east coast of the US was selling. This next one is from that estate – a beautiful mix of straight and flame grain on a Bertram Pot Grade 60 with a vulcanite taper stem. The pipe is stamped on the mid-left side of the shank Bertram [over] Washington D.C. centered on the shank. Lower on the shank it is stamped with the shape number 60. The finish is dull and has a lot of grime ground into the smooth finish on the bowl and some darkening around the sides of the bowl. There are also some nicks on the outer edge on the backside of the bowl. The bowl was caked with an overflowing lava coat on the top of the rim, heavier toward the back of the bowl. The edges looked okay other than some potential burn damage on the back inner edge. The stem was lightly oxidized, dirty and had light tooth chatter and marks on the top and underside near the button. There were not markings or a logo on the taper stem. Like the rest of the Bertrams in this lot the pipe had promise but it was very dirty. Jeff took photos of the pipe before he started his cleanup work.   He took photos of the rim top and bowl to give a clear picture of the thickness of the cake and the lava on the rim top. The edges of the bowl looked to bin good condition. The lava was thicker toward rear of the rim top and there were remnants of tobacco on the walls of the thickly caked bowl. He also took photos of the top and underside of the stem to show the chatter and tooth marks. Otherwise the stem is quite clean. Jeff took photos of the sides and heel of the bowl to give a picture of what the briar around the pipe looked like. There is some stunning grain under the grime.He took photos of the stamping on the shank. It reads as noted above and is clear and readable. The grade number is lower on the left side near the bowl and reads 60.    As I have worked on Bertrams I have written on the brand and have included the following information. If you have read it in past blogs, you can skip over it. If you have not, I have included the link to Bertram history and information. I would recommend that if you don’t know much about them take some time to read the background. I include a link to the write up on Pipedia (http://pipedia.org/wiki/Bertram). Bertram pipes were based out of Washington DC. They were popular among famous politicians and celebrities of the time. They made many products for them from FDR’s cigarette holders to Joseph Stalin’s favorite pipe. They were considered some of the best America had to offer till they finally closed their doors in the 70s. Bertram graded their pipes by 10s and sometimes with a 5 added (15, 25, 55 etc.), the higher the grade the better. Above 60s are uncommon and 80-90s are quite rare. I have worked on one 120 Grade billiard. I have several blogs that I have written on rebornpipes that give some history and background to Bertram pipes. (https://rebornpipes.com/2015/06/16/an-easy-restoration-of-a-bertram-grade-60-217-poker/). I have included the following link to give a bit of historical information on the pipe company. It is a well written article that gives a glimpse of the heart of the company. http://www.streetsofwashington.com/2012/01/bertrams-pipe-shop-on-14th-street.html#

From this information I learned that all of these Bertrams were made before the closure of the shop in the 1970s. This Bertram Pot has great flame and straight grain on the bowl sides and shank sides. The top and bottom of the bowl has birdseye grain. This pipe has a 60 Grade stamp on it which I am sure explains the quality of the briar. Bertram’s Grading system remains a mystery to me.

Jeff had reamed the pipe with a PipNet Pipe Reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He soaked the stem in Before & After Deoxidizer and rinsed it off with warm water. I took photos of the pipe once I got around to working on it.      The rim top had some slight darkening on the back of the bowl and some damage to the inner edge. The stem surface had some light tooth marks and chatter on both sides near the button. I took a photo of the stamping on the shank. The brand stamp Bertram Washington DC is mid-shank on the left side. The Grade Stamp 60 is lower on the left side toward the bottom. I removed the stem and took a photo to give a sense of the grain and a look of the whole. I started my work on the pipe by cleaning up the inner edge and the rim top. I wrapped a wooden ball from Kenneth with 220 grit sandpaper and sanded the top. I was able to minimize the rim damage and darkening. I worked some more on it with 220 grit sandpaper and then restained it with an oak stain pen. I polished the bowl and the rim top, sides and shank with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiping it down after each pad with a damp cloth. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine.   I set the bowl aside and turned to work on the stem. I “painted” the surface of the stem with the flame of a light to lift the marks. I sanded the ones that remained with a folded piece of 220 grit sandpaper to blend them into the surrounding vulcanite. I started polishing with 400 grit wet dry sand paper.      I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. I gave it a final coat of Obsidian Oil and let it dry.    This Bertram Washington DC Grade 60 Pot with a vulcanite taper stem is a great looking pipe now that it has been restored. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Bertram 60 Pot is another one that is comfortable in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ½ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of this pipe is 33 grams/1.16 ounces. If you are interested in adding this pipe to your collection I will be adding it to the rebornpipes store in the American Pipemakers section. Send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Breathing Life into a Classic Older Meerschaum Bulldog with a Golden Bakelite Stem

Leave a reply

Blog by Steve Laug

The next pipe I chose to work on is a meerschaum Bulldog that Jeff picked up from an antique back in October, 2017 from Bozeman, Montana, USA. It was a classic straight Bulldog with a golden Bakelite taper stem. The finish on the bowl and rim cap were scratched and worn looking but still had a lot of charm. The twin rings separating the bowl from the rim cap are in good condition. There is some damage/chips in the rings and nicks in the bowl. There was a thick cake in the bowl and heavy lava overflow on top the rim. The meerschaum was very dirty and under the grim it seemed to be developing a patina on the shank and lightly on the bowl and rim top. The golden Bakelite stem was threaded to be turned onto the metal tenon that was firmly anchored in the shank of the pipe. The stem had deep tooth marks on the top and underside ahead of the button. I loved the shape but it was in rough condition and needed a lot of work. Jeff took photos of the pipe before he started his work on it. He took photos of the rim top and the stem to show the condition. You can see the issues on the rim top and stem as I noted above. There are also some scratches on the rim top itself that I am hoping will polish out and look much better. You can see the tooth damage on the stem surfaces on both sides ahead of the button. Jeff took photos of the side and heel of the bowl. You can see the classic lines and nicely carved bowl of the pipe. It is a great looking Bulldog carved from block meerschaum and is well made. There are a lot of scratches and nicks in the meerschaum around the sides, top and shank of the pipe. There was no stamping on the shank or pipe that identified the maker. It was clearly a no name pipe but it was quite nice. Jeff had cleaned up the pipe with his usual thoroughness. He carefully reamed the pipe with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He cleaned the stem Soft Scrub cleanser and rinsed it off with warm water. I took photos of the pipe 3 years later when I finally got around to working on it. The rim top and inner edge of the rim were in rough condition. The rim top was chipped and nicked. There was darkening on the top and both the inner and outer edges of the bowl along with some dark chips in the surface of the meerschaum.The stem surface looked very good with some tooth marks and chatter on both sides near the button. I removed the stem and took several photos of the pipe to give a sense of the whole. The tenon is anchored in the shank and is threaded metal. The golden Bakelite diamond shaped taper stem is also threaded and screws onto the tenon.I worked on the rim top and inner edge of the bowl with a folded piece of 220 grit sandpaper to remove the damage and as many of the pits and nicks as possible. It looked much better at this point in the process.I polished the smooth meerschaum with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I worked on the darkening of the rim top at the same time. I wiped the bowl down after each pad with a damp cloth. The longer I polished it the more the patina came to the surface. The pipe became more beautiful with each grit of polishing pad. While I was not able to remove all of the scratching around the rim top and bowl I was able to minimize them a bit. The remainder are a part of the story of the pipe’s journey and will remain. I set the bowl aside and turned my attention to the stem. I filled in the deep tooth marks on the stem surface on both sides with clear CA glue. Once the repairs cured I sanded them smooth with 220 grit sandpaper. I started polishing the stem with 400 grit wet dry sandpaper. I polished the stem with micromesh sanding pads. I dry sanded it with 1500-12000 pads and wiped the bowl down after each pad with a cloth and Obsidian Oil. I finished polished it with Before & After Fine and Extra Fine stem polish. I wiped it down with the cloth and Obsidian Oil one final time and set aside to dry. This Classic No Name Meerschaum Straight Bulldog with a golden Bakelite stem really is a beautiful pipe. The polished meerschaum has a stunning shape. I put the stem back on the bowl and carefully buffed the pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Meerschaum Bulldog is another pipe that fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 59 grams/ 2.08 oz. This Meerschaum Bulldog is a real beauty and the rich amber coloured Bakelite stem just highlights the beauty. Jeff made another great find when he picked this up in Bozeman. I will be putting on the rebornpipes store in the Ceramic and Meerschaum Pipe Section. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Restoring a Hand Carved Meerschaum Dublin with a 9mm Acrylic Filter Stem

Leave a reply

Blog by Steve Laug

The next pipe I chose to work on is the second meerschaum that came from a trip Jeff and his wife took  to Europe in the Fall of 2017. He also picked it up in a bazaar in Frankfurt, Germany. It was a nicely carved smooth Dublin with a black acrylic stem. The finish on the bowl and rim top were scratched and worn looking but still had a lot of charm. Like the other one this bowl and rim top appear to have been quickly cleaned for the sale but there was still a light cake in the bowl and some lava spots on the inner edge and rim top. The meerschaum was beginning to develop a patina on the shank and lightly on the bowl and rim top. There was a silver shank band that was tarnished but gave the pipe a bit of bling. The black acrylic stem had a wide open tenon that was made for a 9mm filter which is not surprising. It gave a good first impression but had deep tooth marks on the top and underside ahead of the button. He took photos of the rim top and the stem to show the condition. You can see the issues on the rim top and stem as I noted above. There are also some scratches on the rim top itself that I am hoping will polish out and look much better. You can see the tooth damage on the stem surfaces on both sides ahead of the button. The mortise on the stem has been fitted with a nylon tenon that holds 9mm filters. The shank has been lined with nylon/Delrin and the tenon fits snug in the shank. Jeff took photos of the side and heel of the bowl. You can see the graceful lines and nicely carved bowl of the pipe. It is a lightweight block meerschaum that is well made. There are a lot of light scratches around the sides and top. He took a photo of the stamping on the underside of the silver fitted ferrule. It is stamped 925 which is the silver mark for the piece.There was no stamping on the shank or pipe that identified the maker. It was clearly a no name pipe but it was quite nice. Jeff had cleaned up the pipe with his usual thoroughness. He carefully reamed the pipe with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He cleaned the stem Soft Scrub cleanser and rinsed it off with warm water. I took photos of the pipe 3 years later when I finally got around to working on it. The rim top and inner edge of the rim looked very good with some slight darkening on the rim top and inner edge. The stem surface looked very good with some deep tooth marks and chatter on both sides near the button.     I removed the stem and took a photo of the pipe to give a sense of the whole. The tenon is Delrin and is integrated in the stem. It is drilled to hold a 9mm filter and fits snug in the shank. The stem is a nice looking black saddle acrylic.I polished the smooth meerschaum with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I worked on the darkening of the rim top at the same time. I wiped the bowl down after each pad with a damp cloth. The longer I polished it the more the patina came to the surface. The pipe became more beautiful with each grit of polishing pad. I took out my Dr. Perl Junior 9mm filters made by Vauen to fit one to the stem of this beauty. It fit in mortise and tenon perfectly and did not inhibit the air flow significantly just like the Altinay I just finished.I set the bowl aside and turned my attention to the stem. I filled in the deep tooth marks on the stem surface on both sides with clear CA glue. Once the repairs cured I sanded them smooth with 220 grit sandpaper. I started polishing the stem with 400 grit wet dry sandpaper. I polished the stem with micromesh sanding pads. I dry sanded it with 1500-12000 pads and wiped the bowl down after each pad with a cloth and Obsidian Oil. I finished polished it with Before & After Fine and Extra Fine stem polish. I wiped it down with the cloth and Obsidian Oil one final time and set aside to dry. This No Name Meerschaum Dublin with a black acrylic stem is a beautiful pipe. The polished light weight meerschaum that shines through the polished finish is stunning. I put the stem back on the bowl and carefully buffed the pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished No Name Meerschaum Dublin is another pipe that fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 ½ inches, Height: 2 ¼ inches, Outside diameter of the bowl: 2 inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 57 grams/ 1.98 oz. This Meerschaum Dublin is a real beauty and the 9mm filter black acrylic stem just highlights the beauty. Jeff made another great find when he picked this up in Frankfurt. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Restoring a Hand Carved Meerschaum Calabash with a 9mm Acrylic Filter Stem

1 Reply

Blog by Steve Laug

The next pipe I chose to work on came from a trip Jeff and his wife took  to Europe in the Fall of 2017. He picked it up in a bazaar in Frankfurt, Germany. It was a nicely carved smooth Calabash with a round brass Altinay logo on the ruby coloured acrylic stem. The finish on the bowl and cap were scratched and worn looking but still had a lot of charm. The bowl and rim top appear to have been quickly cleaned for the sale but there was still a light cake in the bowl and some lava spots on the inner edge and rim top. The meerschaum was beginning to develop a patina on the shank and lightly on the bowl and rim top. The ruby coloured acrylic stem was made for a 9mm filter which is not surprising. It gave a good first impression but had deep tooth marks on the top and underside ahead of the button. He took photos of the rim top and the stem to show the condition. You can see the issues on the rim top and stem as I noted above. There are also some scratches on the rim top itself that I am hoping will polish out and look much better. You can see the tooth damage on the stem surfaces on both sides ahead of the button. The mortise on the shank has been fitted with a nylon tenon that holds 9mm filters. The stem has been drilled out to fit snug over the tenon. Jeff took photos of the side and heel of the bowl. You can see the graceful lines and nicely carved bowl of the pipe. It is a lightweight block meerschaum that is well made. There are a lot of visible scratches around the sides and top. He took a close up photo of the left side of the bowl to show the scratches. He took a photo of the brass Altinay two pipe logo inset on the left side of the taper stem.I turned to Pipephil to see what I could learn about the brand (http://pipephil.eu/logos/en/logo-a4.html). There was a sidebar that said that the Altinay Pipe Co Ltd. was founded in 1964 in Eskişehir (Turkey). I did a screen capture of the section on the site and included it below.I then turned to Pipedia to learn a bit more about the brand (https://pipedia.org/wiki/Altinay). I have copied pertinent information on the history of the brand below.

HISTORY OF ALTINAY

Necdet Altınay (1941-2018), who worked in various jobs from a young age to support his family, entered the meerschaum carving sector at the age of 14 and became a meerschaum master at a young age by training from the best masters of the time.

After developing himself in all areas of meerschaum carving such as compositions, sculptural works, famous claw figures until the age of 23, he founded Altınay Pipe Co. in 1964 and started working on purely classical style pipes by noticing the important deficiency in the pipe industry about classical style meerschaum pipes.

He has developed his skills on classical pipes with tactics he received from European pipe masters and has gained an important place in the sector with international fairs he attended regularly.

The importance he attaches to quality and customer satisfaction in his business has made the ALTINAY brand a popular and sought-after brand in meerschaum sector. And soon started exporting worldwide, America, Russia China and especially in Europe through distributors.

Besides his own brand ALTINAY, he also produced meerschaum pipes for world famous brands such as Dunhill, Peterson, Savinelli, Chacom, Brebbia, Butz Choquin. As it is already for Rattrays and Andreas Bauer now.

After working 3 generations together for several years, before he passed away in 2018, largely transferred his superior skills and vision to his son (Nedim Altınay,1967) and grandson(Said Altınay,1990), whom he worked and trained for many years. Now Nedim and Said are working together to take the company further in His quality and vision…

Jeff had cleaned up the pipe with his usual thoroughness. He carefully reamed the pipe with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He cleaned the stem Soft Scrub cleanser and rinsed it off with warm water. I took photos of the pipe 3 years later when I finally got around to working on it. The rim top and inner edge of the rim looked very good with some slight darkening on the rim top and inner edge. The stem surface looked very good with some deep tooth marks and chatter on both sides near the button. I took a photo of the logo on the left side of the taper stem. The fit of the stem to the shank is snug. The shank also shows some patina developing nicely along its length.I removed the stem and took a photo of the pipe to give a sense of the whole. The tenon is nylon and is integrated in the shank. The stem is drilled to slide snug on the tenon. The stem is a nice looking ruby red acrylic. I polished the smooth meerschaum with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I worked on the darkening of the rim top at the same time. I wiped the bowl down after each pad with a damp cloth. The longer I polished it the more the patina came to the surface. The pipe became more beautiful with each grit of polishing pad. I took out my Dr. Perl Junior 9mm filters made by Vauen to fit one to the stem of this beauty. It fit in mortise and tenon perfectly and did not inhibit the air flow significantly. Impressive.I set the bowl aside and turned my attention to the stem. I filled in the deep tooth marks on the stem surface on both sides with clear CA glue. Once the repairs cured I sanded them smooth with 220 grit sandpaper. I started polishing the stem with 400 grit wet dry sandpaper. I polished the stem with micromesh sanding pads. I dry sanded it with 1500-12000 pads and wiped the bowl down after each pad with a cloth and Obsidian Oil. I finished polished it with Before & After Fine and Extra Fine stem polish. I wiped it down with the cloth and Obsidian Oil one final time and set aside to dry. This Altinay Meerschaum Calabash with a ruby coloured acrylic stem is a beautiful pipe. The polished light weight meerschaum that shines through the polished finish is stunning. I put the stem back on the bowl and carefully buffed the pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Altinay Meerschaum Calabash fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 ½ inches, Outside diameter of the bowl: 2 inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 55 grams/ 1.94 oz. This Altinay Calabash is a real beauty and the 9mm filter ruby coloured acrylic stem just highlights the beauty. Jeff made a great find when he picked this up in Frankfurt. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

New Life for a Republic Era Peterson’s System Standard Rusticated 314 Bent Billiard

Leave a reply

Blog by Steve Laug

The next pipe I have chosen is another Peterson’s System Standard pipe. This one is a nice smaller size rusticated version of the shape 314. It has a saddle style Peterson’s stem on the shank end. I believe it came to us from the estate of Anglican minister that was a great friend of mine here in Canada. I was in the airport in Hong Kong when his daughter contacted me to tell me of his death and asked if I wanted to take on his pipes. I told her that I was sad to hear of his death but would gladly take on his pipes to restore and sell. This pipe was one that I believe he purchased as an estate and did not smoke. It is very clean other than the dust and debris of time  on the bowl and stem. The bowl and shank were clean with no cake, tars or oils. There was no lava on the rim top. The nickel ferrule was oxidized but undamaged. The pipe was stamped on the underside of the shank and read Peterson’s [arched over] System [over] Standard. To the right of that it was stamped Republic of Ireland stamp in three lines [over] the shape number 314. The ferrule was stamped K& P over Peterson’s on the left side. The stem was lightly oxidized and had tooth marks on both sides ahead of and on the button. There was no “P” stamp on the stem. I took photos of the pipe before I started my clean up work on it.  I took photos of the rim top and bowl as well as the stem to give a sense of the condition of both. The rim top and the inner edge were in excellent condition. There were clean and a bit spotty. I would need to touch up the stain on the top and edge. The stem was clean but had tooth marks on the top and underside ahead of the button. They are visible in the photos.I took photos of the stamping on the underside of the heel and shank. They are clear and readable as noted above. There is some faintness on parts of the stamping but it is still readable.I took the stem out of the shank and took a photo of the overall look of the pipe.When I worked on other 314’s I had turned to a blog about a pipe that  Paresh had restored – a smooth Peterson’s System Standard 314 earlier this year. As usual he had done good work on the research. I turned to his blog and read through his work on the pipe and the background information that he had gathered (https://rebornpipes.com/2021/07/24/helping-a-fellow-piper-with-his-dream-pipea-petersons-system-pipe/). I quote below from the section on his blog regarding the dating of the pipe.

While dating a Peterson’s pipe, I always fall back to my under mentioned favorite site; http://thepetersonpipeproject.blogspot.com/2007/07/dating-peterons-pipes.html

I quote from the above site.

Stamping of Bowl:

During the years of Kapp and Peterson’s business operations, the country of Ireland has undergone several name changes and K&P’s stamping on their pipes reflects these changes. Knowing these changes, a Peterson pipe can be roughly dated and placed in “eras.”

  • The Republic Era is from 1949 until the present. The Republic of Ireland was formed on 17 April 1949. From 1949 to present the stamp for this era is “Made in the Republic of Ireland” in a block format generally in three lines but two lines have been used with or without Republic being abbreviated.

With that information at hand I turned to work on the pipe itself. The bowl of the pipe was clean and did not have any cake. The finish was very clean so I did not need to scrub or clean that with the normal soap. I checked the inside of the shank, the sump and the airway in the stem with alcohol, cotton swabs and pipe cleaners. The surface of the stem was clean and free of oxidation so that was a bonus.I restained the rim top and inner edges with a Black Sharpie Pen to blend it into the rest of the surrounding briar. The match was good.I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips and a horsehair shoe brush. The product works to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. I polished the nickel ferrule with a jewelers cloth to remove the oxidation and give the nickle a shine. It came out looking pretty good. I set the bowl aside and turned my attention to the stem. I “painted” the tooth marks on the surface with the flame of a lighter to lift them as much as possible. I was able to lift many of them but a few still remained. I filled in the remaining tooth marks with clear CA glue and set it aside to cure. I sanded the repairs smooth with a folded piece of 220 grit sandpaper to begin blending them into the stem surface. I started the polishing with some 400 grit wet dry sandpaper.I set the bowl aside and turned to work on the stem. I polished the stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. I gave it a final coat of Obsidian Oil and set it aside to dry. This Republic Era Peterson’s System Standard 314 Rusticated Bent Billiard with a vulcanite stem is a great looking pipe now that it has been restored. The rugged rustication shows a lot of peaks and valleys and depth. The polished finish is stunning. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax on the buffing wheel. I followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Peterson’s System Standard Rusticated 314 fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 1/8 inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 45grams/1.59oz. This one has been reserved for first refusal. If you are interested in being in the queue for this pipe send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Restoring a Paneled Hexagonal Meerschaum Square Shank Dublin Sitter

2 Replies

Blog by Steve Laug

The next pipe on the table is an interesting meerschaum Paneled Hexagonal Meerschaum Square Shank Dublin Sitter with geometric designs and sun bursts around the bowl sides and shank. The rim top was smooth. There was no marking on the pipe to help identify the maker. It is a nicely made pipe by an anonymous carver. There was a nylon insert in the shank and the tenon was nylon or Delrin and was a push tenon inset in the acrylic stem. The stem is a saddle style acrylic in variegated brown/tan/gold. The finish on the bowl was very dirty and grey looking. The top of the rim had a thick coat of lava on it. There was a thick cake in the bowl that would take some care to remove. The square acrylic saddle stem was dirty and the airway was blackened with tars. There was light chatter and marks on both sides near the button. Jeff took some photos of the pipe before he started his clean up work. He took close up photos of the bowl to show the thick cake in the bowl and the lava on the rim top. The stem photos show the tooth chatter and marks on the top and underside near the button. Jeff took some photos of the sides and heel of the bowl to show the pattern that had been carved around the bowl and shank. The bowl was also filthy and had a grey hue of dirt and grim on the finish. Jeff had cleaned the pipe thoroughly. He had reamed it carefully with a PipNet reamer and cleaned that up with a Savinelli Fitsall Pipe Knife. He worked slowly so as not to damage the inner edge of the bowl. He had scrubbed the exterior of the meerschaum with undiluted Murphy’s Oil Soap and a soft tooth brush. He was able to remove the grey tinge of the filth on the sides of the bowl and shank. He cleaned out the interior of the shank and airway with alcohol, pipe cleaners and cotton swabs. He cleaned out the acrylic stem with alcohol, cotton swabs and pipe cleaners to remove the debris and oils in the airway. The bowl has the look of a tall Panel Hexagonal Dublin. The exterior of the bowl looked very good as did the stem. There was still some dark spots on the rim top on the front left side. I took photos of the pipe when it arrived here. I took some close up photos of the rim top and stem. You can see the marks on the back side of the rim top. The tooth chatter on both sides of the stem were quite light.I removed the stem from the shank and took a photo of the parts of the pipe. It is well proportioned and looked really good.I decided to start my work on the pipe by polishing the bowl with micromesh sanding pads. I worked over the rim top with the pads at the same time. I used micromesh pads – dry sanding with 1500-12000 grit pads and wiped the bowl down with a damp cloth after each pad. I was able to remove the dark spots and give the bowl a shine. I set the bowl aside and turned my attention to the stem. I sanded out the tooth marks on both sides of the stem with 220 grit sandpaper. I started the polishing with 400 grit wet dry sandpaper.I polished the newly shaped acrylic stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with a cloth containing some Obsidian Oil. I know Obsidian Oil does nothing for acrylic but I have found that it removes the small particles left behind by the polishing. I finished polishing the surface with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. I gave it a final coat of obsidian Oil and set it aside to dry. It is a beautiful looking variegated brown/tan/gold acrylic stem. This Carved Meerschaum Hexagonal Panel Dublin Sitter turned out to be yet another fun pipe to work on and I was excited to see it come back together. The pipe had a light patina on the rim top and around the bowl and shank. I chose not to rewax it because of the shine that on the bowl. I put the stem back on the bowl and lightly buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The rich polished hexagonal meerschaum on the bowl looks really good with the polished variegated brown/yellow/golden acrylic stem. The bowl and stem came together looking quite spectacular. Give the finished pipe a look in the photos below. I can only tell you that it is another pipe that is much prettier in person than the photos capture. The dimensions of the pipe are Length: 6 inches, Height: 2 ¼ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 53 grams/1.87 ounces. This is truly a great looking Meerschaum. Thanks for walking through the restoration with me as I worked over another beautiful pipe. I will be putting it on the rebornpipes store in the Ceramic and Meerschaum Pipe Section. If you are interested in the pipe send me an email or a message. Thanks for your time.

Taking a Breather and Restoring this Geometric Pattern Meerschaum Dublin

Leave a reply

Blog by Steve Laug

The next pipe on the table is an interesting meerschaum Dublin with geometric designs around the bowl sides and shank. The rim top was smooth. There was no marking on the pipe or on the case to help identify the maker. It is a nicely made pipe by an anonymous carver. The stem is a modified/customized saddle style acrylic in yellow/gold. It is a nice complement to the white of the meerschaum. The finish was surprisingly clean though the top of the rim had some dark spots and lava on it. There was a  thin cake in the bowl that was not too much to deal with. The stem is also quite clean and there was light chatter and marks on both sides near the button. Jeff took some photos of the pipe before he started his clean up work. The first two photos show the pipe in the case and the case without the pipe. It is quite clean and in good condition. Jeff removed it from the case and took photos of the pipe. It is a really nicely made pipe.He took a close up photo of the bowl to show the marks and the lava on the rim top. There was some darkening on the front and back of the top side. The stem photos show the tooth chatter and marks on the top and underside near the button.Jeff took some photos of the sides and heel of the bowl to show the pattern that had been carved around the bowl and shank. Jeff also took photos of the push style tenon. It came out of the stem when turned but remained in the shank. You can also see what appear two numbers 77 on the end of the shank and the stem. My assumption is that the numbers match the parts when the pipe was made. Jeff had cleaned the pipe thoroughly. He had reamed it carefully with a PipNet reamer and cleaned that up with a Savinelli Fitsall Pipe Knife. He worked slowly so as not to damage the inner edge of the bowl. He had scrubbed the exterior of the meerschaum with undiluted Murphy’s Oil Soap and a soft tooth brush. He cleaned out the interior of the shank and airway with alcohol, pipe cleaners and cotton swabs. He cleaned out the acrylic stem with alcohol, cotton swabs and pipe cleaners to remove the debris and oils in the airway and the threads of the push tenon. Once it was clean he turned the tenon into the stem. I took photos of the pipe when it arrived here. The first two photos show the condition of the black case. It was in excellent condition. The third photo shows the pipe in the opened case. It was a great looking pipe. I took the pipe out of the case and took photos of the cleaned pipe. The bowl has the look of a tall Dublin. The exterior of the bowl looked very good as did the stem. There was still some dark spots on the rim top on the front left side. I took some close up photos of the rim top and stem. You can see the marks on the rim top that I noted above. The tooth chatter on both sides of the stem were quite light.I removed the stem from the shank and took a photo of the parts of the pipe. It is well proportioned and looked really good.I decided to start my work on the pipe by polishing the bowl with micromesh sanding pads. I worked over the rim top with the pads at the same time. I used micromesh pads – dry sanding with 1500-12000 grit pads and wiped the bowl down with a damp cloth after each pad. I was able to remove the dark spots and give the bowl a shine. I set the bowl aside and turned my attention to the stem. Since the tooth chatter was quite shallow I polished the newly shaped acrylic stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with a cloth containing some Obsidian Oil. I know Obsidian Oil does nothing for acrylic but I have found that it removes the small particles left behind by the polishing. I finished polishing the surface with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. I gave it a final coat of obsidian Oil and set it aside to dry. It is a beautiful looking golden, yellow acrylic stem. This Carved Meerschaum Dublin with Geometric Patterns turned out to be another fun pipe to work on and I was excited to see it come back together. It was a clean pipe that did not take Jeff too much work to ream and clean. My work was also simpler than expected. I chose not to rewax it because of the shine that still showed on the bowl. I put the stem back on the bowl and lightly buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The rich polished meerschaum on the bowl looks really good with the polished yellow/golden acrylic stem. The bowl and stem came together looking quite spectacular. Give the finished pipe a look in the photos below. I can only tell you that it is much prettier in person than the photos capture. The dimensions of the pipe are Length: 5 ¾ inches, Height: 2 ¼ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: 1 inch. The weight of the pipe is 36 grams/1.27 ounces. This is truly a great looking Meerschaum. Thanks for walking through the restoration with me as I worked over another beautiful pipe. I will be putting it on the rebornpipes store in the Ceramic and Meerschaum Pipe Section. If you are interested in the pipe send me an email or a message. Thanks for your time.