Monthly Archives: June 2020

Restoring & Restemming a Celtic Craft Block Meerschaum from Bob Kerr’s Estate

3 Replies

Blog by Steve Laug

The next pipe I have chosen from the four remaining pipes from Bob Kerr’s Estate is a Genuine Block Meerschaum with a damaged stem. This is the last of Bob’s Block Meerschaum pipes that I have to work on. (Bob’s photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in most of the restorations of the estate to date I thought that I would leave it out this time. Check out some of the recent Dunhill restoration blogs (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

This Meerschaum is stamped Celtic [over] Craft on the left side of the shank. On the underside it is stamped Genuine Block Meerschaum. Over that on the shank end was stamp GT at the top and below the stamp read N14 which is probably the shape number. The fancy vulcanite stem is oxidized, calcified and has a large chunk missing from the underside of the button and stem. From the damage it looked to me like it needed to be replaced. The exterior of the bowl is grimy and dirty. The black flumed top was worn and tired looking on both the rim top and the shank end. There is a thick cake and lava overflow on the rim top. It is thick enough that it is hard to know if there is any damage on top and edges but it looked like there was some damage. Jeff took photos of the pipe to show its general condition before he did his cleanup.   The exterior of the pipe was very dirty – grime and grit ground in from years of use and sitting. This one was obviously one of Bob’s favourites. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some damage on the rim top and edges of the bowl. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides.  Jeff took photos of the sides and the heel of the bowl to give a better feel for the condition of the bowl. It is dirty but the rustication is interesting. The next photos show the stamping on the sides of the shank. The left side is clear and readable and reads as noted above. The stamping on the underside of the shank was also clear and readable as noted above. Jeff also took photos of the stem shank connection with the stem in place and the stem removed. The tenon was metal and inset in the end of the stem. The shank end was filthy and worn.  The stem was dirty and extremely oxidized, calcified and had tooth marks on both sides ahead of the button. It was missing a large chunk of vulcanite from the underside of the stem and button.   I have not heard of the Celtic Craft brand but the way it was made and the stamping style and placement on the pipe and the finish on the pipe was identical to the look and feel of the block meerschaum pipe that restored earlier – a BELT (https://rebornpipes.com/2020/06/11/restoring-a-heavily-smoked-belt-meerschaum-peterson-like-pipe/). I turned to that blog to check if it was possible that the CELTIC CRAFT pipe was made by the same company. While there was nothing definite I am convinced that it is made by the same company. I quote from that blog:

The BELT brand is not one that I am familiar with. I have never heard of the brand in my years of doing this work. I decided to pause before I started my part of the work on the pipe and see what I could learn on the web. I looked on Pipephil’s site and could find nothing listed. I did the same on Pipedia and initially found nothing either. I did a google search for the brand and low and behold the brand came up under Danish Pipe Making Companies under the heading London Meerschaum (https://pipedia.org/wiki/London_Meerschaum). I quote the brief article below as taken from Jose Manuel Lopes book.

“London Meerschaum made some pipes under the name of BELT or THE BELT, I had this confirmed by Bonds of Oxford St. who have 5 smooth bowl versions in stock at the time of writing, these look very similar to standard system full bent Peterson Meerschaums, the smooth versions have silverware stamped L&JS {Les & Dolly Wood, Ferndown} and has Belt and Genuine Block Meerschaum stamped on the bowl. I have seen 1 rusticated version with the same silverware and 2 of which I own 1, have gold plated ware with no hallmarks and are also stamped Belt and Genuine Block Meerschaum. Both smooth and rusticated have P-Lip type stems though the air hole is not on top but at the end as with most non Peterson P-Lips that I have come across. I do not know when London Meerschaum ceased trading but I can say from the one Belt that I own, it’s a very fine pipe and not cheap, well over the £100 mark when new.”

These pipes were evidently sold at least as early as the 1950’s. These may have been made by, or are affiliated with Pomeroy & Cooke Ltd., (Pipes, Artisans and Trademarks, by José Manuel Lopes).

One of the readers of that blog responded with the following information. It cleared up the information above and called the information that it was a Danish Company called London Meerschaum into question.

Jambo/Belt was based in Nothhamptonshire, a small town north of London.

In my mind it was a Manx Made African Meer and now the information trail was twisted. It is now purported to have been made in Denmark, or in Nothhamptonshire near London or on the Isle of Man. Confusing and strange provenance for this old meer but I personally lean toward the Manx Pipes Connection. Now it was time to work on the pipe itself.

With over 125 pipes to clean from Bob’s estate I took a batch of them to the states with me when I visited and left them with Jeff so he could help me out. Jeff cleaned the pipes with his usual penchant for thoroughness that I really appreciate. Once he finished he shipped them back to me. This one was a real mess and I did not know what to expect when I unwrapped it from his box. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the meerschaum and the lava on the rim top. The finish looks very good with an interesting rustic finish around the bowl and shank. Jeff scrubbed the stem with Soft Scrub and soaked it in Before & After Deoxidizer to remove the oxidation on the rubber. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked a lot better. I took photos before I started my part of the work.  I took close up photos of the rim top and the stem surfaces. The rim top looked better but was rough. Some of the surface had been worn smooth. It was clean however and the flumed colour on the rim and shank end had faded with the cleanup work. The stem was another story all together. The metal tenon was good but the threads in the shank were worn so that it would not align. The issue for me was that the metal would continue to wear down the meer and make the fit looser over time. There were deep nicks on all the sharp edges of the diamond stem. The large chip out of the underside of the button and stem was bigger and rougher than I expected. Even though I could rebuild the damaged area I decided that the stem would need to be replaced on this one.    I took photos of the stamping on the shank of the pipe. It is readable and clear. The text reads as noted above.   I took the stem off the shank and took a photo to give a sense of the flow of the pipe. The stem is a bit of a turned freehand stem so I pretty much could use any other turned freehand stem as a replacement.I started my work on the pipe by dealing with the rim top. I used a brass bristle brush to clean up the rim top. I wanted to check out damage to the rim top so the brass bristle brush would remove any remaining grit in the rustication.I used a black stain pen to touch up the flumed top of the bowl, edges and the shank end. The rim top and shank end looked much better.   I set the bowl aside and turned my attention to replacing the stem. I went through my can of stems and found one that would look interesting with the shape of the pipe. It was a new cast stem. I would need to cut off the tenon and drill out the stem for a new tenon.I used the Dremel and sanding drum to cut off the tenon. I had a Delrin tenon that was made to screw into the stem. I found that reversing it and turning it into the shank was a perfect fit. I used a series of drill bits to drill out the end of the stem to receive the smooth end of the tenon. I used the Dremel and sanding drum to remove the excess vulcanite from the stem so that when the tenon was screwed into the shank the stem sat flush in the shank. I glued the tenon in place in the stem with clear super glue and set it aside to let the glue cure.Once the glue cured I turned the stem into the shank and took photos of the pipe as a whole. Still lots of sanding to do but I like the fit of the stem to the shank.   I cleaned up the stepped down stem area on the end of the stem with a needle file to fit in the inset shank end. I also used the file to reduce the thickness of the button. I then heated the stem with a lighter flame to soften the vulcanite. Once it was soft I bent the end of the stem to match the stem that I was replacing. I screwed the stem into the shank and took a photo of the pipe at this point in the process. I am starting to like the looks of this pipe.   I removed the stem from the shank and sanded out the file marks and shaped the button with 220 grit sandpaper and followed that with 400 grit wet dry sandpaper to start the polishing.   I used a potter cutting tool to open up the slot in the end of the button. I wanted to reshape it and open it enough that a pipe cleaner would easily move through the airway.   I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem.    I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips and a horsehair shoe brush to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth and shoe brush to raise the shine. This interestingly finished rusticated Celtic Craft Genuine Block Meerschaum Freehand/Poker from Bob Kerr’s estate looks very good. Even though it is not my personal favourite it must be a great smoking pipe. The finish cleaned up well on the pipe is in great condition and works well with the polished vulcanite taper replacement stem. I carefully buffed the stem with Blue Diamond on the buffing wheel. I gave the bowl multiple coats of Clapham’s Beeswax Polish and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Meerschaum fits nicely in the hand and I think the rustication will feel great when it heats up during smoking. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. If you are interested in carrying on Bob’s legacy with this pipe send me a message or an email. I have more to work on of various brands. Perhaps one of those will catch your attention. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.

Restoring a Comoy’s Golden Grain 28 Billiard from Bob Kerr’s Estate

2 Replies

Blog by Steve Laug

The next pipe I have chosen from Bob Kerr’s Estate is a Comoy’s Golden Grain Billiard with a the three part C on the stem. This is the last of Bob’s Comoy’s pipes that I am working on. (Bob’s photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in most of the restorations of the estate to date I thought that I would leave it out this time. Check out some of the recent Dunhill restoration blogs (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

This Billiard is stamped Comoy’s [over] Golden Grain on the left side of the shank. On the right side it is stamped with the number 28 at the shank/bowl junction and the COM stamp circle is worn but readable near the stem shank junction. The tapered vulcanite stem is oxidized, calcified and has light tooth marks and chatter on both sides near the button. There is a three part C on the left side of the stem. The exterior of the bowl is grimy and dirty. There is a thick cake and lava overflow on the rim top. It is thick enough that it is hard to know if there is any damage on top and edges. Jeff took photos of the pipe to show its general condition before he did his cleanup. The exterior of the pipe was very dirty – grime and grit ground in from years of use and sitting. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some darkening on the rim top and inner edge of the bowl. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides. Jeff took photos of the sides and the heel of the bowl to give a better feel for the condition of the bowl. It is dirty but the grain is very nice around sides. The next photos show the stamping on the sides of the shank. The left side is faint but readable and the right side is even fainter and did not get captured with the photo. With a bright light they both read as noted above.The stem was dirty and extremely oxidized, calcified and had tooth marks on both sides ahead of the button. It was not nearly as chewed the other pipes in Bob’s estate.With over 125 pipes to clean from Bob’s estate I took a batch of them to the states with me when I visited and left them with Jeff so he could help me out. Jeff cleaned the pipes with his usual penchant for thoroughness that I really appreciate. Once he finished he shipped them back to me. This one was a real mess and I did not know what to expect when I unwrapped it from his box. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with good looking grain around the bowl and shank. Jeff scrubbed it with Soft Scrub and soaked it in Before & After Deoxidizer to remove the oxidation on the rubber. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked a lot better. I took photos before I started my part of the work. I took some close up photos of the rim top and also of the stem surface. I wanted to show what cleaned bowl and rim top looked like. The rim top shows some darkening but the inner edge of the bowl looks very good. The bevel is in excellent condition. I also took close up photos of the stem to show the light tooth marks and the remaining oxidation on the stem surface. You can also see the marks on the surface of the stem.I took photos of the stamping on both sides of the shank and it is faint but readable. It is stamped as noted above. I removed the stem for the shank and took a photo of the bowl and stem to give a picture of what it looked like. You can see the dents in the stem surface.Now, on to my part of the restoration of this Comoy’s Golden Grain 28 Billiard pipe. Since the pipe was in such good condition I decided to start by polishing the bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping the briar down with a damp cloth after each sanding pad. I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth and shoe brush to raise the shine. I set the bowl aside and turned my attention to the stem. I scrubbed off the oxidation on the stem surface with Soft Scrub and cotton pads. I rubbed it down until the oxidation was gone. It was definitely looking better. I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This Comoy’s Golden Grain28 Billiard from Bob Kerr’s estate has some beautiful grain. It turned out to be another great looking pipe. The finish on the pipe is in great condition and works well with the polished vulcanite taper stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Comoy’s Golden Grain Billiard fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. If you are interested in carrying on Bob’s legacy with this pipe send me a message or an email. I have more to work on of various brands. Perhaps one of those will catch your attention. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.

Restoring a Comoy’s Tradition 92 Billiard from Bob Kerr’s Estate

Leave a reply

Blog by Steve Laug

The next pipe I have chosen from Bob Kerr’s Estate is a Comoy’s Tradition Billiard with a replacement stem. Bob had several Comoy’s Tradition pipes and this is the second of them I am working on. (Bob’s photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in most of the restorations of the estate to date I thought that I would leave it out this time. Check out some of the recent Dunhill restoration blogs (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

This Billiard is stamped Comoy’s [over] Tradition on the left side of the shank. On the right side it is stamped with the number 92 at the shank/bowl junction and the other stamping is worn out. The tapered vulcanite stem is a replacement. The stem is oxidized, calcified and has light tooth marks and chatter on both sides near the button. The exterior of the bowl is grimy and dirty. There are burn marks on the top of the shank and on the heel of the bowl. There is a thick cake and lava overflow on the rim top. It is thick enough that it is hard to know if there is any damage on top and edges. Jeff took photos of the pipe to show its general condition before he did his cleanup. The exterior of the pipe was very dirty – grime and grit ground in from years of use and sitting. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some darkening on the rim top and inner edge of the bowl as well as a burn mark on the top front of the bowl. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides. Jeff took photos of the sides and the heel of the bowl to give a better feel for the condition of the bowl. It is dirty but the grain is very nice around sides. The next photos show the stamping on the sides of the shank. The left side is faint but readable and the right side is even fainter and did not get captured with the photo. With a bright light they both read as noted above.The replacement stem was dirty and extremely oxidized, calcified and had tooth marks on both sides ahead of the button. It was not nearly as chewed the other pipes in Bob’s estate.With over 125 pipes to clean from Bob’s estate I took a batch of them to the states with me when I visited and left them with Jeff so he could help me out. Jeff cleaned the pipes with his usual penchant for thoroughness that I really appreciate. Once he finished he shipped them back to me. This one was a real mess and I did not know what to expect when I unwrapped it from his box. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with good looking grain around the bowl and shank. Jeff scrubbed it with Soft Scrub and soaked it in Before & After Deoxidizer to remove the oxidation on the rubber. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked a lot better. I took photos before I started my part of the work. I took some close up photos of the rim top and also of the stem surface. I wanted to show what cleaned bowl and rim top looked like. The rim top shows damage and charring on the inner edge of the bowl. I also took close up photos of the stem to show the light tooth marks and the remaining oxidation on the stem surface. You can also see the marks on the surface of the stem.I took photos of the stamping on both sides of the shank and it is faint but readable. It is stamped as noted above.  I removed the stem for the shank and took a photo of the bowl and stem to give a picture of what it looked like. You can see the dents in the stem surface.Now, on to my part of the restoration of this Comoy’s Tradition 92 Billiard pipe. I decided to start by dealing with the damage to the rim top and the inner edge of the bowl. I carefully topped the bowl on a board with 220 grit sandpaper to start removing the damage to the bowl. I used a folded piece of 220 grit sandpaper to clean up the damage to the bevel of the inner edge of the rim. I polished the bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping the briar down with a damp cloth after each sanding pad. I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth and shoe brush to raise the shine. I set the bowl aside and turned my attention to the stem. Whoever had made this replacement stem had done a pretty horrible job on the tenon. It is pinched around the stem end and the end of the tenon is crooked as well. It was really a mess. I filled in the pinched tenon with black super glue. I sanded the repair and repeated the process until it was smooth and even.I filled in the deep tooth mark on the top of the stem ahead of the button and built up the button surface on the underside with super glue.I sanded out the remaining tooth marks and scratches on the stem surface with 220 grit sandpaper and started polishing them with 400 grit wet dry sandpaper. I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This Comoy’s Tradition 92 Billiard from Bob Kerr’s estate has some beautiful grain. Even with the burn marks it still is a beauty. It turned out to be another great looking pipe. The finish on the pipe is in great condition and works well with the polished vulcanite taper replacement stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Comoy’s Tradition Billiard fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¼ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. If you are interested in carrying on Bob’s legacy with this pipe send me a message or an email. I have more to work on of various brands. Perhaps one of those will catch your attention. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.

Ready For a Second Inning – Georg Jensen 72 Ekstra # 130 Compact Lumberman

Leave a reply

Blog by Paresh Deshpande

I had randomly selected four pipes to work on since I prefer to put a few pipe stems together in the “Before And After” Deoxidizer solution that has been developed by Mark Hoover. I have completed the restoration of two of these pipes, a Wally Frank “BLACKTHORNE” sandblast billiard and another also a Wally Frank stamped Natural Unvarnished Bulldog with two dots.

The third pipe that I decided to work on is not a classic Lovat or its variants, a Lumberman or a Canadian, but I would prefer to call it short compact Lumberman. This pipe is stamped on the upper smooth oval shank surface as “GEORG JENSEN” over “made in Denmark PIPES” and on the bottom of the shank surface as “72 EKSTRA” followed by shape code “130” towards the shank end. The stampings are all crisp and deep. The high quality vulcanite diamond saddle stem bears the logo of interlinked letters “GJ”. The smooth briar, shape and quality of the stem all oozed high quality. This would be the first Georg Jensen pipe that I have worked on and thus my curiosity was piqued as I have worked on and handled pipes from Denmark made by carvers like Preben Holms, Nording, Soren etc, but never a Georg Jensen pipe. I first searched rebornpipes and came across a catalogue uploaded by Jacek A. Rochacki. However, the pipe on my work table finds no mention of it in the brochure. The article has an interesting snippet of information that is reproduced below.

* “our” Georg Jensen – the pipe maker is not this famous Georg Jensen – Danish designer, silversmith and sculptor.

Here is the link to the article

https://rebornpipes.com/2014/04/13/georg-jensen-pipe-brochure-jacek-a-rochacki/

Having hit a wall here, I turned my attention to pipedia.org to gather background information about the carver and his work. Here is the link to the write up on Georg Jensen and a brief of the carver that I have reproduced from the site.

https://pipedia.org/wiki/Georg_Jensen

The Georg Jensen pipe factory was founded by Per Georg Jensen and his wife in 1954, in Kopenhagen, Denmark. Since the 80s the company is under the management of his daughter Lis, and his son with the same name, Per Georg Jensen. The company manufactured around 2,000 factory pipes per year. Among the top of the line pipes are hand carved special editions and free hands.

Top of the Line models of Georg Jensen have vulcanite or ebonite stems, factory pipes usually have acrylic stems.

Factory pipes (in increasing quality) were marked:

Danish Sand Achat / Amber Red Flame / Red Skin Sunrise / Orange extra / Starline Contrast / Bicolour / Harmon Excellent / Masterpiece

Pipes were commonly marked (in increasing quality) with: MODEL + MODEL NUMBER + “Made in Denmark”, GJ stamp in red on the stem. MODEL NUMBER + “Georg Jensen” in italic or fancy font.

Extremely rare and collectible freehands were marked with:

“Straight Grain” and a number that discerns the grading from 1 (lowest) to 13 (highest).

Special edition pipes were marked with: MODEL + MODEL NUMBER + “Handmade in Denmark” + GJ stamp in white on the stem.

The factory closed down in 2001 when Per Georg Jensen (jr) became “Tobacco Professor” for MacBaren Tobacco house.

Well, again there are no matching grades for the factory pipes or similarity in commonly marked pipes and it definitely is not a freehand pipe!!

I surf the net and visited Smokingpipes.com which has been some excellent source of information on pipe brands and found an exact same pipe as that is currently on my work table with the shape and stampings matching to the T. However, the details that were available were similar to that I had read on pipedia.org. Given below is the link to the site.

https://www.smokingpipes.com/pipes/estate/denmark/moreinfo.cfm?product_id=284941

I have not been able to accurately pinpoint the period that this pipe was made in or the grading of this pipe in Georg Jensen line up, so any assistance in this regard is welcome and highly appreciated.

Initial Visual Inspection
This pipe has a compact size with an oval shank and short saddle stem akin to a Lumberman. However the compact size of the pipe with a shorter shank length compels me to designate this shape as a short Lumberman. The stummel boasts of some beautiful cross grains to the front and back of the bowl and shank. The stummel is covered in dirt and grime of the overflowed lava. There is not a single fill in the briar which speaks of high quality selection of the briar. There is a decent layer of cake in the chamber and some damage is seen to the rim top surface. The stem is heavily oxidized with a few deep bite marks to the button edge in the bite zone. Here is how the pipe appears as it sits on my work table. Detailed Inspection Of The Pipe And Observations
The bowl is slightly off round with a decently wide rim and a depth of about 1 7/8 inches. The draught hole is in the center and at the bottom of the chamber. The chamber has an uneven layer of thick crumbly cake. The smooth outward sloping rim top surface is severely damaged with dents/ dings and covered in lava overflow, dirt and grime. The inner front rim edge has suffered a few blows on a hard surface resulting in a dented and chipped edge surfaces to the between 12 o’clock and 2 o’clock direction and the same in enclosed in a yellow circle. The outer rim edge too has some minor dents in the 6 o’clock direction. The condition of the inner walls of the chamber can be commented upon after the cake has been taken down to the bare briar. There is a sweet smell in the chamber which is not very strong. The stummel appears solid to the touch all around and hence I do not foresee any serious damage to the walls in the form of burnout/ deep heat fissures/ lines or pits. The darkened inner rim edge may be charred further than anticipated and the same will be confirmed after the surface has been thoroughly cleaned. I need to resort to topping the rim top in order to address the damage to the surface. The ghost smells should reduce once the cake from the chamber is removed and the shank has been cleaned. The smooth stummel surface is covered in dust and grime through which one can make out the beautiful cross grains to the front and back of the bowl and shank. The stummel surface is peppered with scratches, dents and dings on the either sides of the stummel, over the foot and to the front and back of the stummel, probably due to likely falls during its time with the previous piper. However, there is not a single fill in the entire stummel, signifying very high quality of briar used in carving this pipe. The briar is looking lifeless and bone dry. I shall need to sand the stummel surface with sand papers to remove and minimize the scratches, dents and dings. Once the stummel has been thoroughly cleaned, these damages will be more apparent. Thorough cleaning and rising under warm water of the stummel surface should highlight the grain patterns. Micromesh polishing will further help minimize these dents and scratches to some extent. The mortise shows accumulation of oils, tars and gunk and the air flow is not full and smooth.The high quality vulcanite saddle stem is so heavily oxidized that it appears brownish green in color! Some minor tooth chatter and light tooth marks over the button edge is seen on the upper surface of the stem. There are a couple of very deep bite marks on the lower stem surface that have completely damaged the button edge. These issues are nothing serious to address. The lip edge on both sides is damaged and would necessitate a rebuild followed by reshaping. The tenon has accumulated ash and oils/ tars that have dried out on the inside as well as on the outside. The horizontal slot has scratch marks which will have to be addressed. The bite marks will be raised to the surface by heating to the extent possible and further will be filled using charcoal and CA superglue mix.   The Process
I started the restoration of this pipe by first cleaning the internals of the stem with bristled pipe cleaners and 99.9% pure isopropyl alcohol. I scraped out the dried oils and tars from the tenon end with my fabricated knife and also removed the dried oils and tars from the slot end. I followed it up by sanding the entire stem with a folded piece of 220 grit sand paper to remove the surface oxidation. It has been our (Abha, my wife and self) experience that sanding a stem before dunking it in to the deoxidizer solution helps in bringing the deep seated oxidation to the surface which in turn make further cleaning a breeze with fantastic result.    I dropped the stem in to “Before and After Deoxidizer” solution developed by my friend Mark Hoover. The solution helps to draw out heavy oxidation to the surface, making its further removal a breeze, while the minor oxidation is eliminated to a very great extent. The initial sanding helps to draw out the complete oxidation as the sanding opens up the stem surface that has been initially covered with oxidation. I usually dunk stems of 4-5 pipes that are in-line for restoration and this pipe is marked in pastel blue arrow. I generally allow the stems to soak in this solution overnight to do its work.While the stem was soaking in the deoxidizer solution, I worked on the stummel by first reaming the chamber with size 3 Castleford reamer head. I further scraped the chamber walls with my fabricated knife to remove the remaining carbon deposits where the reamer head could not reach. I scraped out the lava overflow from the rim top surface, especially from the area in the 12 o’clock direction. Once the cake was reamed back to the bare briar, I used a 150 grit sand paper followed by 220 grit sand paper to remove all the traces of remaining cake and also to smooth out the inner walls of the chamber surface. Finally, to remove the residual carbon dust, I wiped the chamber with a cotton pad wetted with 99.9% pure isopropyl alcohol. The chamber walls are sans any damage. The inner rim edge has a number of nicks which were revealed after the lava overflow was removed from the rim top. Thankfully the inner rim was not charred under the lava overflow. The ghost smells are negligible and may further reduce after the shank/ mortise are thoroughly cleaned.  With the bowl internals clean, I move to clean the exterior of the stummel. I used a hard bristled tooth brush and Briar Cleaner, a product that has been developed by Mark Hoover, to scrub the stummel and rim top. I set the stummel aside for 10 minutes for the product to draw out all the grime from the briar surface. After 10 minutes, I washed the stummel under running warm water with anti oil dish washing detergent till the stummel surface was clean and dried it using paper towels and soft cotton cloth. I simultaneously cleaned the shank internals with the detergent and hard bristled shank brush and set the stummel aside to dry out naturally. The stummel surface has cleaned up nicely with the beautiful grain patterns on full display.  While the stummel was drying, the next morning, Abha removed the stems (stem indicated with pastel bue arrow is the one being worked on) that had been soaking in the deoxidizer solution overnight. She cleaned the stem and the stem airway under running warm water and scrubbed the raised oxidation from the stem surface using a scotch brite pad and the airway with a thin shank brush. She further removed the oxidation by scrubbing the stem with 0000 grade steel wool and applied a little EVO to rehydrate the stem. This now gives a clearer picture of the extent of depth of the bite marks as can be seen in the pictures below. These will definitely require a fill. The oxidation is deep and stubborn and can be seen over the stem surface and in the concave of the saddle, as dirty brown coloration. I need to further sand the stem to completely remove the oxidation.I used a 220 grit sand paper to sand the stem and remove all the oxidation that was raised to the surface. This step further reduced the tooth chatter and bite marks present on the stem. I wiped the stem with Murphy’s Oil soap on a cotton swab. This helps in cleaning the stem surface while removing the loosened oxidation. Using a lighter, I flamed the surface of the stem. This helped in raising some of the tooth chatter and bite marks to the surface as vulcanite has a property to regain its original shape on heating. I used a white correction pen to highlight the stem logo. I smeared the correction ink over the logo and once dried, I shall gently wipe out the excess ink. The remaining tooth chatter and bite marks would be addressed subsequently by filling it with a charcoal and superglue mix.I addressed the deeper tooth chatter and bite marks by filling them up with a mix of activated charcoal and CA superglue. Once I had applied the mix, I set it aside to cure overnight. Once the fill has hardened, I shall file and sand the fills to match the surface of the stem and sharpen the button edges on either surface.  With the fills in the stem set aside to cure, I turned my attention back to the stummel. It was time to address the nicks, dents/ dings over the rim top and uneven inner rim edge. I decided to top the rim top surface, a process for which I have an aversion. However, it is a necessary evil if the rim top and rim edges are heavily damaged. I top the rim on a square piece of 220 grit sand paper, frequently checking for the progress. Once I was satisfied that the rim top is evenly smooth and also the damage to the inner (in 12 o’clock and 2 o’clock direction) and outer (dents in the 6 o’clock direction) rim edge has been reduced, I stopped the process of topping. Here is how the rim top surface appears at this point in restoration. The process of topping has flattened the rim top which originally had a slight OUTWARD slant from the inner rim edge. A few minor nicks to the inner and dings to the outer edge are still visible. I shall address these issues by hand sanding the edges to create a slight bevel to both the inner and outer edges.With a folded piece of worn out 180 grit sand paper pinched between my thumb and forefinger, I create a very slight bevel to the inner edge. This helped to remove the remaining nicks from the inner edge. With the same grit sand paper, I created a bevel to the outer edge while at the same time with outward movement of the sand paper, gave a slight outward slope from the inner edge. The rim top surface and the edges look very neat at this stage. Next I addressed the numerous scratches and dings to the stummel surface. I sand the stummel surface with a piece of 220 grit sand paper to remove/ minimize the scratches over the stummel surface. Though 95% of the scratches and dings have been eliminated, there still remains few very minor dings that are remnants of the deeper ones. I accept these dings as part of this pipe’s journey till date.  I followed it by wet sanding the stummel with 1500 to 12000 grit micromesh pads, wiping frequently with a moist cloth to check the progress. I really like the looks of the stummel at this point in restoration. The grains and the clean lines of this piece of briar is really appreciable. Next, I rubbed a small quantity of “Before and After Restoration Balm” deep in to the briar with my finger tips and let it rest for a few minutes. The balm almost immediately works its magic and the briar now has a nice vibrant appearance with the beautiful grain patterns displayed in their complete splendor. I further buffed it with a horse hair brush. The contrast of the dark browns of the flame and cross grains with the natural finish of the rest of the stummel adds an interesting dimension to the appearance of the stummel which may be insufficiently described in words and be rather seen in person.  With the stummel rejuvenation almost complete, save for the final wax polish, I worked the stem. The fill had hardened and with a flat head needle file, I worked on the filling till I had achieved a rough match with the surrounding surface and had sufficiently sharpened the button edges. For a better blending, I further sand the entire stem with 220 followed by 400, 600 and 800 grit sand paper. This helps to reduce the scratch marks left behind by the more abrasive 220 grit paper. To bring a deep shine to the vulcanite stem, I polished the stem, wet sanding with 1500 to 2000 grit sandpapers followed by further wet sanding with 3200 to 12000 grit pads. I wiped the stem with moist cloth after each pad and rubbed it down with Extra Virgin Olive oil to rejuvenate the vulcanite. The finished stem is shown below. The oxidation on this stem was the deepest and the most difficult to remove of all the pipes that I have worked on till date and I have worked on quite a few disastrous stems!! At one point in time, I had to resort to a 150 grit sand paper, the most abrasive one that I have in my inventory. The scratch marks left behind by the sand paper are still visible in the pictures but not noticeable in person (if that’s any consolation…) I have now reached the homestretch in this restoration project. To complete the restoration, I mount a cotton cloth buffing wheel on to my hand held rotary tool and polished the stummel and stem with Blue Diamond compound. This compound helps to remove the minor scratch marks that remain from the sanding. I mount another cotton buffing wheel that I have earmarked for carnauba wax and applied several coats of the wax. I finished the restoration by giving the entire pipe a rigorous hand buffing using a microfiber cloth to raise the shine further. The finished pipe looks amazingly beautiful. The finished pipe is as shown below. P.S. In my last write up a question “Why do I enjoy bringing these old battered and discarded pipes back to life?” had popped up in my mind.

Well, the first and foremost reason that I enjoy this hobby is because I enjoy smoking a pipe and it being an instrument of joy for me, is of utmost importance. Thus, bringing these instruments of enjoyment back to life from obscurity to function as it was intended to be gives me immense pleasures. I am sure the readers will understand this reasoning.

I wish to thank each one for sparing their valuable time to read through this write up and each one is my prayers. Stay home…stay safe!!

An Inherited Pipe Thought To Be Sasieni, Turned Out To Be A Wally Frank “Natural Unvarnished” Bulldog.

2 Replies

Blog by Paresh Deshpande

I had randomly selected four pipes to work on since I prefer to put a few pipe stems together in the “Before And After” Deoxidizer solution that has been developed by Mark Hoover. I have completed the restoration of one of these pipes, a Wally Frank “BLACKTHORNE” sandblast billiard.

The moment I had picked up this pipe, as had happened with the BLACKTHORNE, I thought this pipe to be a Family era Sasieni what with the two dots that peered back at me and the classic Bulldog shape. However, when I saw the stampings, again for the second time on the trot it turned out to be a US brand. The smooth briar, shape and quality of the stem all oozed high quality.

The pipe is a Bulldog with a diamond shank and a straight diamond saddle stem. It is a medium sized pipe with a nice hand feel and the light weight makes it easy for clenching. This pipe is stamped on the upper left smooth surface of the shank as “WALLY FRANK” over “LTD” and on the upper right shank surface as “NATURAL UNVARNISHED” over “IMPORTED BRIAR”, all in block capital letters. The stampings appear faint due to accumulation of dirt and grime over the surface. The high quality vulcanite diamond saddle stem has two Blue Dots. I had read about Wally Frank, while researching a Wally Frank Blackthorne, as being an old Tobacconist from around New York City in US who also sold English made pipes under his name since 1930s. The NATURAL UNVARNISHED was one of the lines/styles of pipes that was offered by Wally Frank. For the readers who wish to acquaint themselves with the Tobacconist and the brand, given below is the link to the write up on pipedia.org.

https://pipedia.org/wiki/Wally_Frank

To unravel the mystery of the two dots, I searched the internet and came across a forum Pipe Smokers Dens where there was thread on Wally Frank. Here is the link to the discussion;

https://pipesmokersdens.com/threads/show-us-your-wally-franks.3139/page-2

I reproduce the relevant part of the discussion which references the TWO DOTs seen on my pipe that makes for an interesting read.

Deadfrog said:

No, it’s just a standard push tenon. It’s a “Wally Frank Limited” & “Made in England”. I never delved too deep into who in England made pipes for them, but if I recall correctly, Sasieni and Charatan supplied them with pipes over the years. Regardless, this was a good buy. Some beautiful grain without a single fill. It’s a nice, classically shaped pipe.

Piffyr Replied

Comoy was their primary British supplier. If the pipe has a shape number, it likely matches the Comoy chart. They also bought pipes from Charatan and (maybe/likely) GBD. Also, a few smaller manufacturers in England that are mostly forgotten today. I think the Sasieni thing started because of the pale blue dots used on the Natural Unvarnished stems coupled with some wishful thinking, but it doesn’t hold up. The pipes aren’t COM stamped and the shapes don’t match. Sometimes, a pale blue dot is just a pale blue dot.

I have not been able to accurately pinpoint the period that this pipe was made in, so any assistance in this regard is welcome and highly appreciated.

Initial Visual Inspection
This pipe has the classic Bulldog shape with the rim cap separated from the rest of the stummel by two rings. The stummel boasts of some beautiful flame and cross grains all over the bowl and shank and is covered in dirt and grime of the overflowed lava. There is not a single fill in the briar which speaks of high quality selection of the briar. There is a decent layer of cake in the chamber. The stem is heavily oxidized with a few deep bite marks in the bite zone. Here is how the pipe appears as it sits on my work table. Detailed Inspection Of The Pipe And Observations
The bowl is in perfect round with a decently wide rim and a depth of about 1 7/8 inches. The chamber has an uneven layer of thick cake. The smooth rim top surface is covered in lava overflow and dirt and grime from previous usage and subsequent storage. The maximum deposition of lava is seen in the 6 o’clock direction (enclosed in blue circle). The inner rim appears to be in pristine condition and the outer rim has suffered a few blows on a hard surface resulting in a few minor chipped edge surfaces. The condition of the inner walls of the chamber can be commented upon after the cake has been taken down to the bare briar. The draught hole is dead center and at the bottom of the chamber and that makes me believe that it should great smoke and the thick cake in the chamber lends credence to this observation. The stummel appears solid to the touch all around and hence I do not foresee any serious damage to the walls in the form of burnout/ deep heat fissures/ lines or pits. The darkened inner rim edge may present a surprise in the form of charred rim edge making the chamber out of round. The smooth stummel surface has taken on a layer of aged patina, through which one can make out the beautiful flame grains all around interspersed with tightly packed cross grains. There are a few minor dents and dings on the lower edge of the diamond shank, probably due to likely falls and or rubbing against other pipes while being stored for more than 40 years. However, there is not a single fill in the entire stummel, signifying very high quality of briar used in carving this pipe. The two rings demarcating the rim cap is intact and the grooves are filled with grime and dust. The briar is looking lifeless and bone dry and has taken on dirty grey hues. I need to be careful while cleaning the paneled shank surfaces to preserve the stampings on this pipe. Thorough cleaning and rising under warm water of the stummel surface should highlight the grain patterns while preserving the patina. In all probability, I shall let these minor dents and dings to the lower edge of the shank remain and avoid the process of sanding the stummel with sand paper in order to preserve the beautiful patina. Maybe, micromesh polishing will address a few of these dents and scratches to some extent. The mortise shows accumulation of oils, tars and gunk and the air flow is not full and smooth. The high quality vulcanite diamond saddle stem is so heavily oxidized that it appears brownish green in color! It is evident that the pipe was used with a softie rubber bite as can be seen from the difference between the area covered by the rubber bite and rest of the stem surface. Some minor tooth chatter and one deep gouge mark is seen on the lower surface of the stem. There are a couple of not very deep bite marks on the upper stem surface. This issue should not be a major headache to address. The lip edge on both sides is in good shape requiring nothing more than minor reshaping. The tenon has accumulated ash and oils/ tars that have dried out on the inside as well as on the outside. The horizontal slot has grime deposits which will have to be cleaned. The tooth chatter and the bite marks will be raised to the surface by heating and the deeper tooth indentations will be filled using charcoal and CA superglue mix. The Process
I started the restoration of this pipe by first cleaning the internals of the stem with bristled pipe cleaners and 99.9% pure isopropyl alcohol. I scraped out the dried oils and tars from the tenon end with my fabricated knife and also removed the dried oils and tars from the slot end. I followed it up by sanding the entire stem with a folded piece of 220 grit sand paper to remove the surface oxidation. It has been our (Abha, my wife and self) experience that sanding a stem before dunking it in to the deoxidizer solution helps in bringing the deep seated oxidation to the surface which in turn make further cleaning a breeze with fantastic result. I dropped the stem in to “Before and After Deoxidizer” solution developed by my friend Mark Hoover. The solution helps to draw out heavy oxidation to the surface, making its further removal a breeze, while the minor oxidation is eliminated to a very great extent. The initial sanding helps to draw out the complete oxidation as the sanding opens up the stem surface that has been initially covered with oxidation. I usually dunk stems of 4-5 pipes that are in-line for restoration and this pipe is marked in yellow arrow. I generally allow the stems to soak in this solution overnight to do its work.While the stem was soaking in the deoxidizer solution, I worked on the stummel by first reaming the chamber with size 1 and 2 Castleford reamer heads. I further scraped the chamber walls with my fabricated knife to remove the remaining carbon deposits. I scraped out the lava overflow from the rim top surface, especially from the area in the 6 o’clock direction. Once the cake was reamed back to the bare briar, I used a 150 grit sand paper followed by 220 grit sand paper to remove all the traces of remaining cake and also to smooth out the inner walls of the chamber surface. Finally, to remove the residual carbon dust, I wiped the chamber with a cotton pad wetted with 99.9% pure isopropyl alcohol. The chamber walls are sans any damage. There are a couple of minor chips to the inner edge of the inner rim which revealed themselves after the lava overflow was removed from the rim top in 7 o’clock direction. Thankfully the inner rim was not charred under the lava overflow. The ghost smells are negligible and may further reduce after the shank/ mortise are thoroughly cleaned. This was followed by cleaning the mortise with q-tips, pipe cleaners and shank brush dipped in isopropyl alcohol. I scraped the walls of the mortise with my fabricated knife to remove the dried oils and tars. I was surprised to find the shank a bit cleaner than I had anticipated from my detailed inspection. The ghost smells are history and the chamber now smells clean.With the bowl internals clean, I move to clean the exterior of the stummel. I used a hard bristled tooth brush and Murphy’s Oil soap to scrub the stummel and rim top. For this stummel cleaning, l I used Murphy’s Oil soap as I wanted to preserve the old patina that had developed on the stummel and was not sure how the Briar cleaner product would affect it. After the scrub with oil soap, I washed the stummel under running warm water with anti oil dish washing detergent till the stummel surface was clean and dried it using paper towels and soft cotton cloth. I simultaneously cleaned the shank internals with the detergent and hard bristled shank brush and set the stummel aside to dry out naturally. The stummel surface has cleaned up nicely with the beautiful grain patterns on full display. While the stummel was drying, the next morning, Abha removed the stems (stem indicated with yellow arrow is the one being worked on) that had been soaking in the deoxidizer solution overnight. She cleaned the stem and the stem airway under running warm water and scrubbed the raised oxidation from the stem surface using a Scotch Brite pad and the airway with a thin shank brush. She further removed the oxidation by scrubbing the stem with 0000 grade steel wool and applied a little EVO to rehydrate the stem. This now gives a clearer picture of the extent of depth of the bite marks as can be seen in the pictures below. These will definitely require a fill. The oxidation is deep and stubborn and can be seen over the stem surface and in the concave of the diamond shape, as dirty green coloration. I need to further sand the stem to completely remove the oxidation.I used a 220 grit sand paper to sand the stem and remove all the oxidation that was raised to the surface. This step further reduced the tooth chatter and bite marks present on the stem. I wiped the stem with Murphy’s Oil soap on a cotton swab. This helps in cleaning the stem surface while removing the loosened oxidation. Using a lighter, I flamed the surface of the stem. This helped in raising some of the tooth chatter and bite marks to the surface as vulcanite has a property to regain its original shape on heating. The remaining tooth chatter and bite marks would be addressed subsequently.I addressed the deeper tooth chatter and bite marks by filling them up with a mix of activated charcoal and CA superglue. Once I had applied the mix, I set it aside to cure overnight. Once the fill has hardened, I shall file and sand the fills to match the surface of the stem and sharpen the button edges on either surface.With the fills in the stem set aside to cure, I turned my attention back to the stummel. The minor dents to the lower edge of the diamond shank was bothering me as I wanted it to be as pristine as was possible. I decided to sand it down with a higher grade sandpaper. With a folded piece of 600 grit sandpaper I sand dents along the either sides of the shank edge till the dents are not easily discernible. I followed it by wet sanding the stummel with 1500 to 12000 grit micromesh pads, wiping frequently with a moist cloth to check the progress. I really like the looks of the stummel at this point in restoration. The grains and the clean lines of this piece of briar is really appreciable.  Next, I rubbed a small quantity of “Before and After Restoration Balm” deep in to the briar with my finger tips and let it rest for a few minutes. The balm almost immediately works its magic and the briar now has a nice vibrant appearance with the beautiful grain patterns displayed in their complete splendor. I further buffed it with a horse hair brush. The contrast of the dark browns of the flame and cross grains with the natural unvarnished finish of the rest of the stummel adds an interesting dimension to the appearance of the stummel which may be insufficiently described in words and be rather seen in person. With the stummel rejuvenation almost complete, save for the final wax polish, I worked the stem. The fill had cured and with a flat head needle file, I worked on the filling till I had achieved a rough match with the surrounding surface and had sufficiently sharpened the button edges. For a better blending, I further sand the entire stem with 220 followed by 400, 600 and 800 grit sand paper. This helps to reduce the scratch marks left behind by the more abrasive 220 grit paper. To bring a deep shine to the vulcanite stem, I went through the complete set of micromesh pads, wet sanding with 1500 to 2000 grit sandpapers followed by further wet sanding with 3200 to 12000 grit pads. I wiped the stem with moist cloth after each pad and rubbed it down with Extra Virgin Olive oil to rejuvenate the vulcanite. The finished stem is shown below. I have now reached the homestretch in this restoration project. To complete the restoration, I mount a cotton cloth buffing wheel on to my hand held rotary tool and polished the stummel and stem with Blue Diamond compound. This compound helps to remove the minor scratch marks that remain from the sanding. I mounted another cotton buffing wheel that I have earmarked for carnauba wax and applied several coats of the wax. I finished the restoration by giving the entire pipe a rigorous hand buffing using a microfiber cloth to raise the shine further. The finished pipe looks amazingly beautiful and is ready to join my collection. I only wish it could share with me its life story of the past years while I enjoy smoking my favorite Virginia blend in it or maybe an English blend or maybe just keep admiring it!! The finished pipe is as shown below. P.S. As I was working this pipe, a fleeting question “Why do I enjoy bringing these old battered and discarded pipes back to life?” crossed my mind…

I wish to thank each one for sparing their valuable time to read through this write up and each one is my prayers. Stay home…stay safe!!

Restoring a Comoy’s Tradition 292 Billiard from Bob Kerr’s Estate

Leave a reply

Blog by Steve Laug

The next pipe I have chosen from Bob Kerr’s Estate is a Comoy’s Tradition Billiard with a Comoy’s C on the stem. Bob had several Comoy’s Tradition pipes and this is the first of them I am working on. (Bob’s photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in most of the restorations of the estate to date I thought that I would leave it out this time. Check out some of the recent Dunhill restoration blogs (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

This Billiard is stamped Comoy’s [over] Tradition on the left side of the shank. On the right side it is stamped with the number 292 at the shank/bowl junction and the circular COM stamp. The tapered vulcanite stem had a Comoy’s C on the left side. The stem is oxidized, calcified and has light tooth marks and chatter on both sides near the button. The exterior of the bowl is grimy and dirty. There are burn marks on the top of the shank and on the heel of the bowl. There is a thick cake and lava overflow on the rim top. It is thick enough that it is hard to know if there is any damage on top and edges. Jeff took photos of the pipe to show its general condition before he did his cleanup. The exterior of the pipe was very dirty – grime and grit ground in from years of use and sitting. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some darkening on the rim top and inner edge of the bowl as well as a burn mark on the top front of the bowl. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides.  Jeff took photos of the sides and the heel of the bowl to give a better feel for the condition of the bowl. You can see the burn mark on the right side of the heel toward the front. The next photos show the stamping on the sides of the shank. The left side is faint but readable and the right side is even fainter and did not get captured with the photo. With a bright light they both read as noted above.The stem was dirty and extremely oxidized, calcified and had tooth marks on both sides ahead of the button. It was not nearly as chewed the other pipes in Bob’s estate.With over 125 pipes to clean from Bob’s estate I took a batch of them to the states with me when I visited and left them with Jeff so he could help me out. Jeff cleaned the pipes with his usual penchant for thoroughness that I really appreciate. Once he finished he shipped them back to me. This one was a real mess and I did not know what to expect when I unwrapped it from his box. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with good looking grain around the bowl and shank. Jeff scrubbed it with Soft Scrub and soaked it in Before & After Deoxidizer to remove the oxidation on the rubber. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked a lot better. I took photos before I started my part of the work. I took some close up photos of the rim top and also of the stem surface. I wanted to show what cleaned bowl and rim top looked like. The rim top shows damage and charring on the inner edge of the bowl. I also took close up photos of the stem to show the light tooth marks and the remaining oxidation on the stem surface. You can also see the marks on the surface of the stem.I took photos of the stamping on both sides of the shank and it is faint but readable. It is stamped as noted above.  You can see the C on the left side of the stem.I took some photos of the burn marks on the right front heel of the bowl and the topo of the shank near the stem junction. The burn mark did not go too deep in the briar. It looks like the pipe was laid in an ashtray against a burning ash or coal. The burn on the bowl front did not go through into the bowl so it was not a burn out. The inside of the bowl was smooth and undamaged.I removed the stem for the shank and took a photo of the bowl and stem to give a picture of what it looked like. You can see scratches in the stem surface.Now, on to my part of the restoration of this Comoy’s Tradition 292 Billiard pipe. I decided to start by dealing with the damage to the rim top and the inner edge of the bowl. I carefully topped the bowl on a board with 220 grit sandpaper to start removing the damage to the bowl. I used a folded piece of 220 grit sandpaper to clean up the damage to the bevel of the inner edge of the rim.I sanded the burn marks on the bowl front and the top of the shank with 220 grit sandpaper. While I could not remove the damage in total I was able to minimize it. I polished the bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping the briar down with a damp cloth after each sanding pad. I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth and shoe brush to raise the shine. I set the bowl aside and turned my attention to the stem. I filled in the small dents with clear super glue. Once the repairs had cured I used a needle file to smooth out the fills in preparation for sanding and blending them into the surface of the stem. I sanded out the remaining tooth marks and scratches on the stem surface with 220 grit sandpaper and started polishing them with 400 grit wet dry sandpaper. I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This Comoy’s Tradition 292 Billiard from Bob Kerr’s estate has some beautiful grain. Even with the burn marks it still is a beauty. It turned out to be another great looking pipe. The finish on the pipe is in great condition and works well with the polished vulcanite taper oval stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Comoy’s Tradition Billiard fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. If you are interested in carrying on Bob’s legacy with this pipe send me a message or an email. I have more to work on of various brands. Perhaps one of those will catch your attention. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.

Restoring a B. Barling & Sons Guinea Grain 4025 TVF Apple  from Bob Kerr’s Estate

Leave a reply

Blog by Steve Laug

The next pipe I have chosen from Bob Kerr’s Estate is a B. Barling & Sons Guinea Grain oval shank apple with a Barling Cross on the top of the stem. It is the first of Bob’s Barlings pipes. (Bob’s photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in most of the restorations of the estate to date I thought that I would leave it out this time. Check out some of the recent Dunhill restoration blogs (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

This Apple is stamped Guinea Grain [over] B. Barling & Sons on the top side of the stem. On the underside it is stamped with the number 4025 T.V.F. [over] Made in Denmark. The tapered oval stem had a Barlings Cross on the top. The stem is oxidized, calcified and has light tooth marks and chatter on both sides near the button. The exterior of the bowl is grimy and dirty. There is a thick cake and lava overflow on the rim top. It is thick enough that it is hard to know if there is any damage on top and edges. Jeff took photos of the pipe to show its general condition before he did his cleanup. The exterior of the pipe was very dirty – grime and grit ground in from years of use and sitting. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some darkening on the rim top and inner edge of the bowl as well as a burn mark on the top front of the bowl. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides.  Jeff took photos of the sides and the heel of the bowl to give a better feel for the condition of the bowl. The next photos show the stamping on the sides of the shank and it is very readable. It reads as noted above. The stem was dirty and extremely oxidized, calcified and had tooth marks on both sides ahead of the button. It was not nearly as chewed the other pipes in Bob’s estate.Before doing cleanup work on the pipe I decided to do some research on the pipe. I looked first on the Pipephil website and found some information on the B. Barling & Sons Guinea Grain, Made in Denmark 4025 with an oval tapered stem. (http://www.pipephil.eu/logos/en/logo-barling.html#modernguineagrain). I did a screen capture of the section on the brand that fits the pipe I am working on.The pipe is identified as a Modern Guinea Grain and is stamped the same as the one pictured other than the shape number. It is also noted in a memo there as Post-Transition Period.

I turned to Pipedia (https://pipedia.org/wiki/Barling) and read the section on the rough outline on the history of the brand that links the brand with the English section of the company. I quote:

I’m retaining the terms Transition and Post Transition here because the following information underscores why they’re not useful designations. As stated earlier in this update, the Transition era began in October of 1960 and ended in February of 1963. During the first 20 months of the Transition Era, the pipes that the Barling Company produced under Finlay ownership are indistinguishable from the pipes that the Barling Company produced under Barling ownership. The Barling family continued to manage the company for Finlay. The constants are the quality of the product and family management. The product of the first 20 months of the Transition can’t be identified, so the distinction is meaningless.

I did a search on the stamping “Made in Denmark” and came across a discussion on Pipesmoker Unlimited Forum (http://pipesmokerunlimited.com/archive/index.php/t-5515.html). I quote a section from that forum below:

“By 1970, the range of products had expanded to such an extent that Imperial Tobacco decided to reassign the Barling operation to its Ogden branch. About the same time the two Barling factories at Park Street and Jeffrey Place were closed down and the production of Barling pipes was outsourced to independent pipemakers. After a year or so, operations were transferred to Ogden’s Liverpool factory. Production of Barling pipes was shifted to several Danish firms, amongst them Eric Nording.”

The pipe I am working on is definitely from the Corporate Period which includes the Post transition period. The four digit shape number, the block stamping Guinea Grain and B. Barling & Sons, the T. V.F. (The Very Finest) all point to the pipe being from this time period. The Made in Denmark stamp identifies the pipe as being made around 1970 when Barling pipes were made in Denmark by several Danish firms.

With over 125 pipes to clean from Bob’s estate I took a batch of them to the states with me when I visited and left them with Jeff so he could help me out. Jeff cleaned the pipes with his usual penchant for thoroughness that I really appreciate. Once he finished he shipped them back to me. This one was a real mess and I did not know what to expect when I unwrapped it from his box. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with good looking grain around the bowl and shank. Jeff scrubbed it with Soft Scrub and soaked it in Before & After Deoxidizer to remove the oxidation on the rubber. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked a lot better. I took photos before I started my part of the work.  I took some close up photos of the rim top and also of the stem surface. I wanted to show what cleaned bowl and rim top looked like. The rim top shows damage and charring on the inner edge of the bowl. I also took close up photos of the stem to show the light tooth marks and the remaining oxidation on the stem surface. You can also see the hash marks on the surface of the stem.I took photos of the stamping on both sides of the shank and it is clear and readable. It is stamped as noted above.  You can see the remnants of the Barling cross on the top of the stem in the first photo below.I removed the stem for the shank and took a photo of the bowl and stem to give a picture of what it looked like. You can see scratches in the stem surface.Now, on to my part of the restoration of this Barling’s Guinea Grain pipe. I decided to start by dealing with the damage to the rim top and the inner edge of the bowl. I carefully topped the bowl on a board with 220 grit sandpaper to start removing the damage to the bowl. I used a folded piece of 220 grit sandpaper to clean up the damage to the bevel of the inner edge of the rim. I polished the bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping the briar down with a damp cloth after each sanding pad. I stained the sanded rim top with a Maple stain pen to blend it into the surrounding briar. Once the stain cured I polished the briar to further blend it into the bowl.I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth and shoe brush to raise the shine. I set the bowl aside and turned my attention to the stem. I “painted” the surface of the stem with the flame of a lighter. The heat lifted the majority of the dents in the stem surface. It also had the added benefit of burning off some of the oxidation.I scrubbed the surface of the stem with Soft Scrub to further remove the remaining oxidation. The product works wonders in removing the oxidation on the stem. It took a bit of scrubbing but I was able to remove the majority of the oxidation around the shank end.I sanded out the remaining tooth marks and scratches on the stem surface with 220 grit sandpaper and started polishing them with 400 grit wet dry sandpaper. I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem.  Even though I avoided the faint stamping of the Barling Cross there was not enough depth to the stamp to hold white paint. It is still visible but just not deep enough to restore. This Barling Guinea Grain 4025 TVF Apple, Danish made pipe from Bob Kerr’s estate turned out to be another great looking pipe. The finish on the pipe is in excellent condition and works well with the polished vulcanite taper oval stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Guinea Grain oval shank Apple fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¼ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. This is one of Bob’s pipes that I am holding on to for a while as I really like the Danish flair it has. I have about 10 more of Bob’ pipes to go. Perhaps one of those will catch your attention. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.

Restoring a KB&B Kaywoodie Drinkless English Made 95B Pot from Bob Kerr’s Estate

1 Reply

Blog by Steve Laug

The next pipe I have chosen from Bob Kerr’s Estate is a KB&B Drinkless Kaywoodie English Made Pot with an unmarked stem. It is the last of Bob’s English made Kaywoodies. (Bob’s photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in most of the restorations of the estate to date I thought that I would leave it out this time. Check out some of the recent Dunhill restoration blogs (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

This Pot is stamped DRY in a KBB style cloverleaf followed by Drinkless [over] Kaywoodie [over] Made in England on the left side of the shank. On the right side it is stamped with the number 95B. The DRY stamp in the cloverleaf was new to me. The tapered stem is missing the typical white inlaid Kaywoodie Cloverleaf logo. The tenon is threaded and has been modified with the removal of the stinger. The stem is oxidized, calcified and has light tooth marks and chatter on both sides near the button. The exterior of the bowl is grimy and dirty. There is a thick cake and lava overflow on the rim top. It is thick enough that it is hard to know if there is any damage on top and edges. Jeff took photos of the pipe to show its general condition before he did his cleanup. The exterior of the pipe was very dirty – grime and grit ground in from years of use and sitting. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some darkening on the rim top and inner edge of the bowl. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides.    Jeff took photos of the sides and the heel of the bowl to give a better feel for the condition of the bark around the bowl.The next photos show the stamping on the sides of the shank and it is very readable. It reads as noted above.The stem was dirty and extremely oxidized. The stem appeared to be a replacement as it is missing the Kaywoodie logo and the metal stinger/tenon has been modified. I have learned that Bob was a chewer and his stems seemed to have been replaced often. This one at least fit well to the shank and did not yet have the chew marks that were a norm on Bob’s pipes.Before doing cleanup work on the pipe I decided to do some research on the pipe. I looked first on the Pipephil website and found some information on the white club inlay on the left side of the tapered stem. (http://www.pipephil.eu/logos/en/logo-kaywoodie.html). Since I did not have the original stem the information there was less helpful.

I turned to Pipedia (https://pipedia.org/wiki/Kaywoodie) and read the section on the rough outline on the history of the brand that links the brand with the English section of the company. I quote:

Again, demand for KBB pipes and especially Kaywoodie prompted another move for both the manufacturing facilities and the corporate offices. In 1930 the corporate office moved into the Empire State Building on Fifth Avenue in New York. By 1935, the manufacturing operations moved from Union City to 6400 Broadway in West New York, New Jersey which, at the time, was touted as the largest pipe making facility in the world. At the height of production, there were 500 employees producing up to 10,000 pipes per day.

The corporate offices were relocated in 1936 to the International Building, Rockefeller Center, 630 Fifth Avenue, New York. The invitation to visit the new office reads, “Kaywoodie is now on display at the world’s most famous address – Rockefeller Center. Here Kaywoodie takes its place among the leaders of industry and commerce.” The move to Rockefeller Center coincided with The Kaywoodie Company’s emergence as a subsidiary of KBB. All of the pipes manufactured by KBB including the Yello-Bole line were also on display here. By 1938 Kaywoodie had opened an office in London to meet worldwide demand. Kaywoodie of London was jointly owned with another famous pipemaker, Comoy’s of London.

From there I turned to a link on the article to a section called Guide to Kaywoodie Pipes (https://pipedia.org/wiki/Collector%27s_Guide_to_Kaywoodie_Pipes#NOTES_ON_.22OTHER.E2.80.9D_KAYWOODIE_PIPES).

English Kaywoodies. All of the catalogs reviewed in this research contained the following copyright notification: Printed in U.S.A., Kaufmann Bros. and Bondy, Inc., New York and London. Kaywoodie Pipe cases and smoker’s accessories were also marked with “New York and London”. The catalogs, however, do not present any information concerning Kaywoodie’s London operations, or how the English Kaywoodies might have differed from those manufactured and marketed in the U.S. Lowndes notes that he has several English Kaywoodies acquired in Vaduz and Zurich. English Kaywoodies are now made by Oppenheimer pipes. Lowndes notes that English Kaywoodies with the “screw-in bit” come in Ruby Grain, Custom Grain, Standard, and Relief Grain grades. The traditional push-bit models come in Continental Plain and Relief, London Made, Minaret, Air-way Polished No. 707, and Lightweight grades. Prices in 1985 ranged from 9.50 (pounds) to 26.00 (pounds). Lowndes notes that the Super Star was a special edition English Kaywoodie made of finest briar with a handmade silver band. Lowndes has two: one from Zurich with a large white-outlined logo, and beautifully cased; and one in walnut finish with the black-­in-white logo. A recent catalog shows the Super Star without a band and the ordinary small white logo. A 1985 letter from Oppenheimer states that the black-in-white logo has been discontinued and only the regular white logo is now used.

I turned to Pipedia’s Kaywoodie Shape Number chart to check out the number 95B that is stamped on the shank side (https://pipedia.org/wiki/Kaywoodie_Shape_Numbers). The chart gives the shape information and the time frame in which the shape was made. I did a screen capture of the shape number information and have included it below.From the above information I now knew that the pipe in hand was a Medium sized Pot with a long saddle stem originally. Somewhere in its life that stem disappeared and was replaced by a long taper stem. The pipe was made between 1940-1972 in London by Oppenheimer. It had screw-in bit.

With over 125 pipes to clean from Bob’s estate I took a batch of them to the states with me when I visited and left them with Jeff so he could help me out. Jeff cleaned the pipes with his usual penchant for thoroughness that I really appreciate. Once he finished he shipped them back to me. This one was a real mess and I did not know what to expect when I unwrapped it from his box. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with good looking grain around the bowl and shank. Jeff scrubbed it with Soft Scrub and soaked it in Before & After Deoxidizer to remove the oxidation on the rubber. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked a lot better. I took photos before I started my part of the work. I took some close up photos of the rim top and also of the stem surface. I wanted to show what cleaned bowl and rim top looked like. The rim top shows damage and charring on the inner edge of the bowl. I also took close up photos of the stem to show the light tooth marks and the remaining oxidation on the stem surface.I took photos of the stamping on both sides of the shank and it is clear and readable. It is stamped as noted above.  The new stamp to me is the KBB style Cloverleaf stamp with the word DRY stamped in the center of the leaf pattern.I unscrewed the stem for the shank and took a photo of the bowl and stem to give a picture of what it looked like. You can see the clipped off stinger that has been modified to leave behind a threaded tenon.Now, on to my part of the restoration of this KBB English Made Pot. I decided to start by dealing with the damage to the rim top and the inner edge of the bowl. I topped the bowl on a board with 220 grit sandpaper to remove the damage to the bowl. I used a folded piece of 220 grit sandpaper to smooth out the damage to the inner edge of the rim. I worked on the inner bevel to clean up the damage and the darkening. I moved on to deal with the gouges in the bowl on the right side. I fill them in with clear super glue. When the repairs had cured I sanded them smooth with 220 grit sandpaper to smooth them out.I stained the repaired and sanded areas with a blend of Cherry, Maple and Walnut stain pens to blend them into the surrounding briar. Once the stain cured I polished the briar to further blend it into the bowl. I polished the bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping the briar down with a damp cloth after each sanding pad. I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bark on the bowl sides and shank with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth and shoe brush to raise the shine. I set the bowl aside and turned my attention to the stem. I “painted” the surface of the stem with the flame of a lighter. The heat lifted the majority of the dents in the stem surface. There was one tooth mark on the underside that was just ahead of the button.There was one deep tooth mark on the underside of the stem next to the button. I filled it in with clear super glue. Once the repair cured I used a needle file to flatten the repair and sharpen the edge of the button. I sanded them out with 220 grit sandpaper and started polishing them with 400 grit wet dry sandpaper.   I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This KB&B Kaywoodie Drinkless 95B Pot, English made pipe from Bob Kerr’s estate turned out to be another great looking pipe. The Walnut finish on the pipe is in excellent condition and works well with the polished vulcanite taper stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished KB&B Kaywoodie Pot fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: 7/8 of an inch. If you are interested in carrying on Bob’s legacy with this pipe send me a message or an email. I have more to work on of various brands. Perhaps one of those will catch your attention. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.

Breathing Life into a Parker Super Bruyere793 Billiard from Bob Kerr’s Estate

Leave a reply

Blog by Steve Laug

I have only 11 more of Bob’s pipes to finish before I have completed the restoration of his estate so I am continuing to work on them. The next one from Bob Kerr’s Estate is Parker Super Bruyere billiard. It is a nice looking Billiard pipe with nice grain. (Bob’s photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in most of the restorations of the estate to date I thought that I would leave it out this time. Check out some of the recent Dunhill restoration blogs that include the biographical notes about Bob. Here is a link to one of them (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

The Parker Super Bruyere Billiard has a taper vulcanite stem. It is a smooth finished bowl and shank that has a lot of dust and debris ground into the finish of the briar. The pipe is stamped on both sides of the shank. On the left it is stamped with the shape number793 followed by Parker over Super in a Diamond over Bruyere. On the right it is stamped with the number 2 in a circle followed by Made in London England. There was a thick cake in the bowl and lava overflow on the rim top. There was tobacco debris stuck on the bottom and sides of the bowl. The tapered vulcanite stem was calcified, oxidized and had tooth marks and chatter ahead of the button on both sides. It had the Parker Diamond P stamp on the topside of the stem. Jeff took photos of the pipe to show its general condition before he did his cleanup. As I mentioned above the exterior of the pipe was very dirty – grime and grit ground in from years of use and sitting. The rim top was covered with a coat of thick lava that overflowed from the thick cake in the bowl. It was hard to know what the rim edges looked like because of the lava.    Jeff took photos of the sides and the heel of the bowl to give a better feel for the condition of the briar around the bowl.       The next photos show the stamping on both sides of the shank. The stamping is clear and readable as noted above. There is also a stamped Diamond P on the top of the tapered stem.   The stem was dirty, calcified and oxidized with tooth chatter and marks on the top and underside of the stem at the button.      I have worked on quite a few Parkers over time and I have seen them stamped like the one I have however, there as a superscript after the D in England. I turned to Pipedia to see what I could find out a Super Bruyere without a date code(http://www.pipephil.eu/logos/en/logo-parker.html). I have included a screen capture of the section showing a similarly stamped pipe. With over 125 pipes to clean from Bob’s estate I took a batch of them to the states with me when I visited and left them with Jeff so he could help me out. Jeff cleaned the pipes with his usual penchant for thoroughness that I really appreciate. Once he finished he shipped them back to me. Bob’s pipes were generally real mess and I did not know what to expect when I unwrapped it from his box. I was surprised to see how well it turned out. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with good looking grain around the bowl and shank. Jeff scrubbed it with Soft Scrub and soaked it in Before & After Deoxidizer to remove the oxidation on the rubber. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked a lot better. I took photos before I started my part of the work.    I took some close up photos of the rim top and the stem surface. I wanted to show what cleaned bowl and rim top looked like. The rim top had some darkening but the inner and outer edges of the bowl were in excellent condition. I also took close up photos of the stem to show the tooth marks and the remaining oxidation on the stem surface.    I took photos of the stamping on both sides of the shank. The stamping on both the left and right side are clear and readable as noted above.    I removed the stem for the shank and took a photo of the bowl and stem to give a picture of what it looked like. The oxidation is very visible.I decided to start my part of the restoration work on this pipe by addressing the damage to the rim top and inner edge first. I topped the bowl on a piece of 220 grit sandpaper on a topping board to smooth out the damage. I used a folded piece of 220 sandpaper to address the damage on the inner edge and bring the bowl back to round.    There was a deep gouge on the left side of the heel of the bowl that I dealt with next. I filled it in with clear superglue and once it had cured sanded it smooth with 220 grit sandpaper.   I polished the briar with micromesh sanding pads – wet sanding it with 1500-12000 grit sanding pads. I wiped it down with a damp cloth between each sanding pad.   I paused the polishing for a moment and stained the rim top with a Maple and an Oak stain pen to blend the rim top colour into the bowl and shank colour.   I went back to polishing the bowl with 6000-12000 grit micromesh sanding pads.  The last three pads helped to blend in the restained areas of the repairs. I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth and shoe brush to raise the shine.      I set the bowl aside and turned my attention to the stem. I painted the stem surface with the flame of a Bic lighter to lift the dents in the surface of the vulcanite. I was able to lift most of them out. What remained were some light marks in the surface.  I scrubbed the stem with Soft Scrub and cotton pads to remove the remaining oxidation. It took a bit of elbow grease but I was able to remove it all. I sanded out the remaining tooth marks on both sides with 220 grit sandpaper. I started the polishing of the stem with 400 grit wet dry sandpaper.      I touched up the Diamond P stamp on the top of the taper stem with Liquid Paper. I worked it into the stamping with a tooth pick. I scraped off the excess with the tooth pick and the finished stamp looked much better.      I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem.    This nice looking Parker Super Bruyere 793 Billiard from Bob Kerr’s estate cleaned up really well and looks very good. The mixed stain brown finish on the pipe is in great condition and works well with the polished vulcanite taper stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Parker Super Bruyere feels great in the hand and I think it will feel great as it heats up with a good tobacco. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ½ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. If you are interested in carrying on Bob’s legacy with this pipe send me a message or an email. I have more to work on of various brands. Perhaps one of those will catch your attention. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.