The next pipe on the work table is an interesting piece that Jeff and I picked up on a pipe hunt in Alberta. It is another Leonard Payne pipe that is very interesting. The bowl has been rusticated to look a bit like tree bark. There is some darkening around the shank bowl junction that when examined appears to be a rejoined shank and bowl. Is it a repair or something else? Once it is cleaned up I will know more about what is there. The metal shank end piece is aluminum and has a tube inside it. The vulcanite stem also has a tube in it. To me it is a lot like Keyser Hygienic pipe in terms of the system structure. The bowl has a thick cake that overflows onto the rim top as lava. There are some nicks and scratches on the top and edges. The exterior was very dirty with grime and debris ground into the finish on the bowl. The inside of the scratched aluminum shank end is filled with tars and oils the same as the stem is. The vulcanite stem is oxidized, scratched and has tooth marks and chatter on both sides ahead of the button. I took some photos of the pipe before I did any clean up.I took photos of the rim top and the stem. The photo of the rim top shows the damage and the thick cake in the bowl and lava on the top. The stem photos show the oxidation, calcification and tooth chatter and light marks on both sides. I took photos of the stamping on the top, right and left side of the shank. The stamping on the left side is the Leonard Payne signature. The stamping on the left side reads CANADA. The stamping on the top of the shank reads Standard.I reread several of the blog I have written on the brand in the past restorations of Payne pipes and decided to include the material on the brand before I write about the clean up of the pipe. I am including advertisement for Leonard Payne’s pipes. Here is the link to the blog.
Further digging with Google came up with this short note from alt.smokers.pipes forum. It was written by Mike Glukler of Briar Blues. I quote it below in full. (https://groups.google.com/forum/#!topic/alt.smokers.pipes/RrICLiVgE2o) “Leonard Payne was based in B.C. for many years. He came to Canada from England. He had shops in Surrey, B.C. and Kelowna, B.C. Interesting fellow. Gruff as the day is long. When you bought a pipe it was handed to you in a paper bag. No sock, no box. Most of his pipes carried a “carburetor” system at the shank / stem junction. Another Payne idea was his shanks. Almost all his pipes were two pieces. He’d turn the bowl and shank, then cut off the shank and reattach with glue (not always with the same piece of briar, so many did not match grains). His thinking was that the shank being the weakest link, if cut and glued would never break and thus “correcting” the weakest link. You may find his pipes on E-Bay on occasion listed as a Len Cayne. The P in his stamping looks more like a fancy upper case C.”
The pipe I am working on fits Mike’s information perfectly. First, there was a carburetor system on this pipe. The aluminum shank extension has a tube in it that matches a tube in the inside of the military bit stem. (I forgot to take a photo of the system before I cleaned it up but you can see the system set up on shank end and stem.The second part of the information from Mike regards the shank and bowl connection. It was obvious that the shank had been cut off the shank and reattached with glue. It was Payne’s belief that since the shank was the weakest link cutting it off and gluing on would remove the possibility of it breaking in the future.
Now it was time to work on the pipe. First I took the pipe apart and took the following photo of the pipe. It was very dirty and needed to be thoroughly cleaned. I reamed the pipe with a PipNet Pipe Reamer and took the cake back to bare briar. I cleaned up the remnants of the cake in the bowl with a Savinelli Fitsall Pipe Knife.I scraped off the rim top with the knife to remove the lava top coat on the rim. The rim looked quite good with the lava removed. Once the rim top was sanded I would be able to polish out the scratches. I used a brass bristle brush to clean off the grime in the briar. Once it was loose I wiped the bowl down with alcohol on cotton pads to remove the grit and grime ground into the briar. With the externals cleaned I cleaned the internals on the metal fitment, the vulcanite stem and the shank with pipe cleaners, cotton swabs and alcohol. I worked on them until they were clean.I rubbed the threads on the shank end down with Vaseline Petroleum Jelly to lubricate it for easily putting it back on the shank. I polished the smooth portions of the rusticated bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping the briar down with a damp cloth after each sanding pad. I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bark on the bowl sides and shank with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. I set the bowl aside and turned my attention to the stem. I sanded out the remaining oxidation, the tooth marks and chatter with 220 grit sandpaper to blend them into the surface of the surrounding vulcanite. I started polishing the stem with 400 grit wet dry sandpaper. I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This Leonard Payne System Pipe is a great looking pipe that has all of the classic Leonard Payne innovations – the carburetor and the cut off and glued on shank to strengthen the connection. The rusticated finish on the pipe is in excellent condition and works well with the polished vulcanite military style taper stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I polished the aluminum shank end with micromesh pads and a jeweller’s cloth to raise the shine. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Canadian Made Leonard Payne Standard is a great looking pipe that looks almost new. The flow of the grain and rustication around the bowl and the shape contribute to beautiful look of this pipe. It fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: 5/8 of an inch. This one is on its way soon to a Leonard Payne collector in Eastern Canada. I look forward to hearing what he thinks of it once he receives it. Thanks for reading this blog and my reflections on the pipe while I worked on it. This was an interesting pipe to bring back to life.
The second of the Kirsten pipes I have chosen to work on from Bob Kerr’s Estate is a Companion polished aluminum coloured Barrel system pipe with a saddle stem. It is the second of Bob’s Kirsten pipes and also the last one I have to work on from the estate. (Bob’s photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in most of the restorations of the estate to date I thought that I would leave it out this time. Check out some of the recent Dunhill restoration blogs (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).
When I think of Kirsten pipes this is the shape that is a typical Kirsten. On the left side of the shank it is stamped with Companion in script. On the underside of the polished aluminum barrel it is stamped Made in U.S.A. followed by K. It is a straight pipe with large Dublin bowl. Metal base is dented and worn. The pipe has gaskets. Stem is oxidized, tooth marks, chatter near the button. Button is damaged. There is a cake in the bowl and lava overflow on the rim. The ridged valve has some damage from what looks like marks left behind by pliers. The pipe is very dirty. Jeff took photos of the pipe to show its general condition before he did his cleanup. The exterior of the pipe was very dirty – grime and grit ground in from years of use and sitting. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some darkening and lava on the rim top. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides. It also appeared that there was some mold on the cake in the bowl.Jeff took a photo of the side and the heel of the bowl to give a better feel for the condition of the bowl. You can see the interesting grain on the bowl side and front.The next photos show the stamping on the sides of the barrel shank and it is very readable. It reads as noted above. The stem was dirty and extremely oxidized, calcified and had tooth marks on both sides ahead of the button. It was not nearly as chewed the other pipes in Bob’s estate. Jeff took apart the pipe and took photos of the parts of the part. It was incredibly dirty with tars and oils on the internals of the pipe.Before doing cleanup work on the pipe I decided to do some research on the pipe. I have a catalogue for Kirsten pipes in my files and found this pipe in the catalogue. It is shown in the photo below. The K stamp identifies it as a Companion pipe.
I am really glad that Jeff helped me work through this estate of over 125 pipes to clean from Bob’s estate. I would in no way be this close to finishing the estate without his help. Jeff cleaned the pipes with his usual penchant for thoroughness that I really appreciate. He had reamed it with a PipNet pipe reamer and cleaned up the remaining cake in the bowl with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with good looking grain around the bowl and shank. Jeff took the pipe apart and cleaned the barrel, the adjustable valve and the stem with alcohol, pipe cleaners and cotton swabs. He scrubbed the stem with Soft Scrub and soaked it in Before & After Deoxidizer to remove the oxidation on the rubber. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked a lot better. I took photos before I started my part of the work. I took some close up photos of the rim top and also of the stem surface. I wanted to show what cleaned bowl and rim top looked like. The rim top and edges of the bowl looked very good. The screw in the bottom of the bowl looks very good with no damage to the slots. I also took close up photos of the stem to show the light tooth marks and the remaining oxidation on the stem.I took the pipe apart and took photos of the parts of the pipe to give a picture of what it looked like.Now, on to my part of the restoration of this Kirsten RX pipe. The rim top was in rough condition and looked as if it had been beat against a hard surface. I decided to begin my work by topping the bowl with 220 grit sandpaper on a topping board.I polished the bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping the briar down with a damp cloth after each sanding pad. I rubbed the bowl down with Before & After Restoration Balm. I worked it into the surface of the bark on the bowl sides and shank with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine.I rubbed the valve on the metal base with some Vaseline Petroleum Jelly. I have found that it keeps the valve from sticking in the base end. I screwed the bowl on the top of the metal barrel. This part of the restoration is finished and the pipe is looking really good at this point in the process. All that remains is the stem and push rod that goes in the end of the base. I set the bowl and metal barrel aside and turned my attention to the stem. There were some deep tooth marks near the edge of the button on both sides. I filled them in with clear super glue.I sanded out the stem surface with 220 grit sandpaper to remove the tooth marks and chatter. I started to polish it with 400 grit wet dry sandpaper.I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This Kirsten Companion Made in USA K pipe from Bob Kerr’s estate turned out to be another great looking pipe. The finish on the pipe is in excellent condition and works well with the polished vulcanite saddle stem. I put the pipe back together and carefully buffed it with Blue Diamond on the buffing wheel. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ½ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: 7/8 of an inch. It will be going on the rebornpipes store soon. If you are interested in carrying on Bob’s legacy with this pipe send me a message or an email. This is the last of Bob’s Estate pipes that I am working on. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.