Tag Archives: restaining a bowl and rim

Fresh Life for a Republic Era Peterson’s “Donegal” Rocky 608S Saddle Stem Pot

Blog by Steve Laug

The next pipe on the work table is a sandblast Peterson’s Rusitcated Pot shaped pipe that we purchased from an auction in Manorville, New York, USA on 07/28/2022. It was stamped on the underside of the shank and read Peterson’s [over] “Donegal” Rocky [over] Made in the Republic of Ireland (in three lines) followed by the shape number 608S. There is a band on the shank that is stamped on the left side and reads K&P in shields [over] Sterling Silver. Under those stamps there are three hallmarks – Hibernia seated, Crowned Harp for country of manufacture and a date letter in this case an oddly shaped upper case “S”. It has a rusticated finish around the bowl and shank that has a lot of oils, debris and grime in the finish. There was a thick cake in the bowl and a heavy lava overflow in the rustication on the rim top. The inner edge of the bowl looks to have significant damage on the left front under the tars and lava. There was a very beautiful pipe underneath all of the buildup of years of use. The stem was a Peterson’s style P-Lip Saddle Stem. It had light tooth marks and chatter on both sides ahead of the button. Jeff took photos of the pipe before he started his cleanup work on it. Jeff took photos of the bowl and rim top to show the thick cake in the bowl and the heavy lava build up on the rusticated rim top and the edges of the bowl. The rim top and edges looked rough but a proper clean up would tell the full story. At this point the inner edge of the left side of the bowl looked to be out of round. Jeff took photos of the top and underside of the stem showing the tooth chatter, scratching, calcification and oxidation on the stem surface and wear on the edges of the button. More would be visible once Jeff cleaned it up. Jeff took photos of the sides and heel of the bowl to show the condition of the finish. You can see the grime and what looks to be white paint around the sides of the bowl and shank in the rusticated finish. It seems to fill in the grooves in the rustication. Jeff took photos of the stamping on the underside of the shank. The stamping was faint but readable as you can see from the photos. It read as noted above. The Sterling Silver ferrule is actually clearly stamped and readable. The hallmarks are light but readable.

I am including the information from Pipedia’s article on Peterson pipes. It is a great read in terms of the history of the brand (https://pipedia.org/wiki/Peterson). I have included a bit of the pertinent history here.

1950 – 1989 The Republic Era – From 1950 to the present time, the stamp for this era is “Made in the Republic of Ireland” in a block format generally in three lines but two lines have been used with or without Republic being abbreviated.

During the 1950’s and 60’s the Kapp & Peterson Company was still in the ownership of the Kapp family. However 1964 saw the retiral of the company Managing Director Frederick Henry(Harry) Kapp.

I turned to the hallmarking chart on one of the blogs on rebornpipes to lock down the date for the pipe (https://rebornpipes.com/wp-content/uploads/2015/05/peterson-cataloguecomp_page_27.jpg). The chart defines the meaning of each hallmark. The first one of the seated woman with a harp is known as the Hibernia stamp and identifies the pipe as made in Ireland. The second stamp is a crowned harp which is a fineness mark denoting the high quality of silver that was used. The third stamp is an oddly shaped S. I have included a larger screen capture of the chart in the lower left of the photo below.

I have drawn a RED CIRCLE around the date letter below. What appeared to be an upper-case S actually is a very stylized G as seen in the circled letter below. It identifies the date of this Peterson’s pipe to 1974.I knew that I was dealing with a Republic Era pipe made between 1950 and the present. The hallmarks date the pipe to 1974. Now it was time to work on the pipe.

Jeff had done a great job cleaning up the pipe as usual. He reamed the pipe with a PipNet reamer and cut back the cake back to the bare briar. He cleaned up the walls with a Savinelli Fitsall Pipe Knife. He scrubbed the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol to remove the tars and oils. He scrubbed the exterior of the pipe with Murphy’s Oil Soap and a tooth brush to remove the grime from the finish. He worked on the rim top lava and darkening with the soap and tooth brush. He scrubbed the inside of the stem with alcohol and pipe cleaners. He scrubbed the exterior of the stem with Soft Scrub and then soaked it in Briarville’s Pipe Stem Deoxidizer. He washed it off with warm water to remove the Deoxidizer. The pipe looked far better when it arrived. The silver tarnished once again and would need to be polished because it had been sitting here for awhile. I took some close up photos of the rim top and also of the stem surface. I wanted to show how well it had cleaned up. The rim top and edges look quite good though the bowl was very out of round with damage to the left side toward the front of the bowl. I also took close up photos of the stem to show the light tooth marks on the surface near the button. I took a photo of the stamping on the underside of the shank and the band. You can see that it is stamped as noted above. It is faint but still readable. I took the pipe apart and took a photo of the pipe. It is a good-looking pipe and has a rugged rustication around the bowl. I started my work on the pipe by addressing the damage on the inner edge of the rim and the top. I built up the damaged edge with clear CA glue and briar dust. The initial start looks pretty awful but follow through the photos. I used a brass bristle brush to clean up the rusticated rim top. I worked over the inner edge of the rim with both a folded piece of 220 grit sandpaper and a piece of dowel wrapped with 220 grit sandpaper. The rim top and edges looked significantly better after the clean up. I touched up the inner edge and the rim top with a Walnut stain pen to match the stain on the briar around the bowl. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips and a horsehair shoe brush to clean, enliven and protect the briar. I let the balm sit for 10 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I polished the Sterling Silver band on the shank with a jeweller’s cloth to remove the tarnish and polish it. I “painted” the surface of the stem with the flame of a Bic lighter to lift the light tooth marks on both sides. I was able to lift all of them. I followed that by sanding it with a folded piece of 220 grit sandpaper. I started the polishing of the stem with 400 grit wet dry sandpaper. I wiped it down with some Obsidian Oil. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I gave it a coat of Obsidian Pipe Stem Oil. It works to protect the stem from oxidizing. I set it aside to dry. I am excited to finish this Republic Era Peterson’s “Donegal” Rocky 608S Pot. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with the rugged rustication all around it. Added to that the polished Sterling Silver band and the black vulcanite stem was beautiful. This rusticated Classic Peterson’s “Donegal” Rocky Pot is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ½ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 29 grams/1.06 ounces. It is a beautiful pipe and one that will be on the Irish Pipe Makers Section of the rebornpipes store soon. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.

As always, I encourage your questions and comments as you read the blog. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipe men and women who hold our pipes in trust until they pass on into the trust of those who follow us.

Restoring a Smooth, Republic Era Peterson’s System Star 307 Sterling Silver Ferrule

Leave a reply

Blog by Steve Laug

The next pipe on the work table is Peterson’s System pipe that we purchased from and estate in Plano, Texas, USA on 03/30/2022. It was stamped Peterson’s [over] System [over] Star on the left side of the shank vertically below the silver ferrule. On the right it is stamped Made in the Republic of Ireland (in three lines) [over] the shape number 307. It has a smooth finish around the bowl and shank that is covered with a lot of oils, debris and grime. There was a thick cake in the bowl with remnants of tobacco stuck on the walls. There was a lava overflow on the rim top that was heavier toward the back side. The top and edges of the rim were well hidden under the tars and lava. There was a very beautiful pipe underneath all of the buildup of years of use. The ferrule on the shank end was oxidized and is stamped on the top and left side Peterson [over] Dublin. That is followed by Sterling [over] Silver. On the underside there are three hallmarks – Hibernia seated, Crowned Harp for country of manufacture and a date letter in this case a lower case “m”. There is a small dent on the underside of the ferrule. The stem was a Peterson’s style P-Lip. It was oxidized and calcified toward the end with some tooth marks and chatter. There were tooth marks on the button itself as well. Jeff took photos of the pipe before he started his cleanup work on it. Jeff took photos of the bowl and rim top to show the thick, hard cake in the bowl with remnants of tobacco stuck on the walls of the bowl. There was a lava build up on the top of the rim and the edges of the bowl. The rim top looked pretty good but it was hard to know for sure if there was damage under the thick lava. Only clean up would tell the full story. Jeff took photos of the top and underside of the stem showing the tooth chatter, scratching, calcification and oxidation on the stem surface and wear on the edges of the button. Jeff took photos of the sides and heel of the bowl to show the condition of the finish. You can see the grime around the sides of the bowl and shank. Even under the dirt and debris of the years it looked very good. Jeff took photos of the stamping on the underside of the bowl and shank. The stamping was faint but readable as you can see from the photos. It read as noted above. The Sterling Silver Ferrule is actually clearly stamped and readable. The hallmarks are light but readable. I have not seen the System Star stamp before so this new stamping made me once again turn to The Peterson Pipe by Mark Irwin & Gary Malmberg. I looked up the System Star in the book and on page 315 it includes this information:

Peterson’s over System over Star (c1979-c.1985, 2010) A high-quality line between the De Luxe and Premier, in smooth burgundy finish with sterling domed mount.

I have included the information on the shape number on this pipe that I picked up on researching the previous pipes. This is the second of two Peterson’s System pipes marked with the 307 shape number that I have worked on in the past few days. I have included a page from a Petersons Catalogue that I have on rebornpipes (https://rebornpipes.com/tag/peterson-hallmark-chart/). I have put a red box around the 307 shown in the catalogue page shown below. That should give a clear picture of the size and shape of the pipe. I am also including the information from Pipedia’s article on Peterson pipes. It is a great read in terms of the history of the brand (https://pipedia.org/wiki/Peterson). I have included a bit of the pertinent history here.

During the 1950’s and 60’s the Kapp & Peterson company was still in the ownership of the Kapp family. However 1964 saw the retiral of the company Managing Director Frederick Henry(Harry) Kapp.

Pipedia also included a section of information on the System pipes including a diagram of the systems look (https://pipedia.org/wiki/Peterson#Republic_Era_Pipes). I quote a section of the article in part and include a link to another article on Pipedia on the System pipe.

The Peterson System pipes are the standard bearers of the Peterson pipe family, famous for the excellent smoking pleasure they provide. Often imitated but never equalled, the Peterson System smokes dry, cool and sweet, thanks to the scientiﬁc effectiveness of the original design. The heart of the System is the unique graduated bore in the mouthpiece. This makes the suction applied by the smoker 15 times weaker by the time it reaches the tobacco chamber. The result is that all the moisture ﬂows into the reservoir and, thus cannot reach the smoker’s mouth. The Peterson Lip further enhances the effectiveness of the graduated bore by directing the ﬂow of smoke upwards and away from the tongue. This achieves a uniquely even distribution of smoke and virtually eliminates any chance of tonguebite or bitterness. Furthermore, the shape is contoured so that the tongue rests comfortably in the depression under the opening. Each “PLip” mouthpiece is made from Vulcanite. For the Peterson System pipes to work properly, the stem/tenon has to have an extension, the tip of which will pass by the draft hole from the bowl and into the sump. Upon the smoker drawing in smoke, this extension then directs the smoke down and around the sump to dispense a lot of the moisture before the smoke enters the extension and stem. On the System Standards and other less expensive systems, this extension with be made of Vulcanite turned integrally with the stem. On the more expensive System pipes this extension will be made of metal which screws into the Vulcanite stem. This extension on the earlier pipes will be of brass and the newer pipes will be of aluminium. Most smokers not knowing this function of the metal extension, assumes that it is a condenser/stinger and will remove it as they do with the metal condensers of Kaywoodie, etc. Should you have a System pipe with this metal extension, do not remove it for it will make the System function properly and give you a dryer smoke (https://pipedia.org/wiki/A_closer_look_at_the_famous_Peterson_Standard_System_Pipe).

I have written many times about the hallmarks on Peterson’s Pipes and have included date charts in the past. Here is another date chart (https://rebornpipes.com/wp-content/uploads/2015/04/peterson-hallmark-chart.jpg). I spelled out the details of the hallmarks in the opening paragraph above but now want to specifically address the date of the pipe. It has a lower case “m” in the cartouche on the silver. Using the chart below the lower case “m” dates the pipe as being made in 1978. I have drawn a red box around the pertinent letter in the screen capture below. With that information in hand I knew what I was dealing with in terms of the stamping and the age of this pipe. I knew from the information that the System Star pipe was made during the Republic Era in 1978. Now it was time to work on the pipe.

Jeff cleaned this filthy pipe with his usual clean up process. This one was a real mess and I did not know what to expect when I unwrapped it from his box. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with great looking grain around the bowl and shank. Jeff soaked the stem in Briarville’s Pipe Stem Deoxidizer to remove the oxidation on the vulcanite. When the pipe arrived here in Vancouver for the second stop of its restoration tour I was amazed it looked so good. I removed the incorrect stem and replaced it with a correct P-Lip stem for a 307 that I had here in my box of stems. The bonus was that the tenon had a brass chimney in the end that was correct for this pipe. I took some close up photos of the rim top and also of the stem surface. I wanted to show what an amazing job Jeff did in the cleanup of the rim top. The rim top was and inner edge were in good condition. There was some darkening and slight damage to the inner edge. The rim top also had some nicks and marks. I also took close up photos of the stem to show the condition of the vulcanite. It was quite clean and the tooth marks on the button and on the stem ahead of the button were very visible in the photos.One of the things I appreciate about Jeff’s cleanup is that he works to protect and preserve the nomenclature on the shank of the pipes that he works on. The stamping on this one was very faint to start with so I was worried that it would disappear altogether with the cleanup. He was not only able to preserve and maintain its condition in the process. I took some photos to show the clarity of the stamping. I have noticed that many restorers are not careful to protect the stamping in their cleaning process and often by the end of the restoration the nomenclature is almost destroyed. I would like to encourage all of us to be careful in our work to preserve this as it is a critical piece of pipe restoration! I took the stem off the shank and took a photo of the pipe. I decided to start my work on the pipe by cleaning up the rim top and inner edge of the bowl with a folded piece of 220 grit sandpaper. I removed the damage on the inner edge and the nicks on the rim top. It looked significantly better. I polished the briar with micromesh sanding pads – dry sanding it with 1500-12000 grit sanding pads. I wiped it down with a damp cloth after each sanding pad to remove the dust. The briar was really shining by the final pad. I rubbed the bowl and rim down with Before & After Restoration Balm. I worked it into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for 10 minutes and then buffed with a cotton cloth to raise the shine. I really like watching the Balm do its magic and bring the briar alive. With briar polished with the Restoration Balm I moved onto the metal. I polished the Sterling Silver ferrule with a jewellers cloth to raise the shine and to protect it from further oxidation. I “painted” the stem surface with the flame of a Bic lighter to lift the tooth marks. I was able to lift them a bit but not totally. I filled in the deep marks that remained with clear CA glue and sit it aside to cure. Once it cured I used a file to flattened the repairs and redefine the button edge. I sanded the stem with 220 grit sandpaper to further blend in the repairs. I started polishing it with 400 grit wet dry sandpaper. I scrubbed the stem with SoftScrub to remove the oxidization left in the vulcanite of the saddle stem. I was able to remove a significant amount of oxidation that was on the saddle portion of the stem. It looked significantly better at this point.I touched up the “P” logo on the left side of the saddle stem with white acrylic fingernail polish. I let it dry then I polished off the excess with a worn 1500 grit micromesh sanding pad. Once the excess was removed the stamp looked much better.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the stem down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I gave it a coat of Obsidian Pipe Stem Oil. It works to protect the stem from oxidizing. I set it aside to dry. Once again at this point in the restoration process I am excited to be on the homestretch. I look forward to the final look when the Peterson System Star 307 is put back together, polished and waxed. I put the bowl and stem back together. I lightly polished the bowl and stem with Blue Diamond to polish out the scratches in the briar and the vulcanite. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The depths of the rustication really pop with the wax and polish. The shiny black vulcanite stem is a beautiful contrast to the browns of the bowl and thick shank and Sterling Silver ferrule. This Republic Era Peterson’s System Star 307 Bent Billiard was another fun pipe to work on. It really is a quite stunning piece of briar whose shape follows the flow of the briar. The pipe feels great in the hand will be better when warmed up while smoking. The finished pipe is shown in the photos below. The dimensions of the pipe are Length: 6 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 2.43 ounces/70 grams. I will be putting it on the rebornpipes store in the Irish Pipemakers Section if you would like to add it to your rack and carry on the previous pipeman’s legacy. This is an interesting estate to bring back to life.

Peterson’s System Standard XL307 Made in the Republic of Ireland Rusticated Bent

Leave a reply

Blog by Steve Laug

The next pipe on the work table is Rusticated Peterson’s System pipe that we purchased from and estate in Plano, Texas, USA on 03/30/2022. It was stamped Peterson’s System Standard on the underside side of the shank in a smooth panel. It was stamped Peterson’s [over] System [over] Standard. That is followed by the shape number XL307 [over] Made in the Republic of Ireland (in three lines). It has a rugged, tactile rustication around the bowl and shank that is fill with a lot of oils, debris and grime. There was a thick cake in the bowl with remnants of tobacco stuck on the walls. There was a lava overflow on the rim top that was heavier toward the back side. The top and edges of the rim were well hidden under the tars and lava. There was a very beautiful pipe underneath all of the buildup of years of use. The nickel ferrule on the shank end was oxidized and is stamped on the top and left side K&P [over] three faux hallmarks. That is followed by Petersons. It is not dented or damaged. The stem was the wrong stem for the pipe. It was not a Peterson’s style P-Lip but rather a Wellington style with the airway exiting on the end of the stem. It was oxidized and calcified toward the end with some tooth chatter. There were also some tooth marks on both sides of the stem ahead of the button. I would need to restem it with a proper stem once I received it in Vancouver. Jeff took photos of the pipe before he started his cleanup work on it. Jeff took photos of the bowl and rim top to show the thick, hard cake in the bowl with remnants of tobacco stuck on the walls of the bowl. There was a lava build up on the top of the rim and the edges of the bowl. The rim top looked pretty good but it was hard to know for sure if there was damage under the thick lava. Only clean up would tell the full story. Jeff took photos of the top and underside of the stem showing the tooth chatter, scratching and oxidation on the stem surface and wear on the edges of the button. You can also see the exit of the airway on the stem end rather than the to of the P-lip. Jeff took photos of the sides and heel of the bowl to show the condition of the finish. You can see the grime in the rustication around the sides of the bowl and shank. Even under the dirt and debris of the years it looked very good. Jeff took photos of the stamping on the underside of the bowl and shank. The stamping was faint but readable as you can see from the photos. It read as noted above. The nickel ferrule on the shank end is stamped on the top and left side K&P Peterson’s over three Peterson marks used on nickel ferrules. I have included the information on the shape number on this pipe that I picked up on researching the previous pipes. This is the second of two Peterson’s System Standard pipes in Bob’s collection marked with the 307 shape number. I have included a page from a Petersons Catalogue that I have on rebornpipes (https://rebornpipes.com/tag/peterson-hallmark-chart/). I have put a red box around the 307 shown in the catalogue page shown below. That should give a clear picture of the size and shape of the pipe. I am also including the information from Pipedia’s article on Peterson pipes. It is a great read in terms of the history of the brand (https://pipedia.org/wiki/Peterson). I have included a bit of the pertinent history here.

During the 1950’s and 60’s the Kapp & Peterson company was still in the ownership of the Kapp family. However 1964 saw the retiral of the company Managing Director Frederick Henry(Harry) Kapp.

The Peterson System pipes are the standard bearers of the Peterson pipe family, famous for the excellent smoking pleasure they provide. Often imitated but never equaled, the Peterson System smokes dry, cool and sweet, thanks to the scientiﬁc effectiveness of the original design. The heart of the System is the unique graduated bore in the mouthpiece. This makes the suction applied by the smoker 15 times weaker by the time it reaches the tobacco chamber. The result is that all the moisture ﬂows into the reservoir and, thus cannot reach the smoker’s mouth. The Peterson Lip further enhances the effectiveness of the graduated bore by directing the ﬂow of smoke upwards and away from the tongue. This achieves a uniquely even distribution of smoke and virtually eliminates any chance of tonguebite or bitterness. Furthermore, the shape is contoured so that the tongue rests comfortably in the depression under the opening. Each “PLip” mouthpiece is made from Vulcanite. For the Peterson System pipes to work properly, the stem/tenon has to have an extension, the tip of which will pass by the draft hole from the bowl and into the sump. Upon the smoker drawing in smoke, this extension then directs the smoke down and around the sump to dispense a lot of the moisture before the smoke enters the extension and stem. On the System Standards and other less expensive systems, this extension with be made of Vulcanite turned integrally with the stem. On the more expensive System pipes this extension will be made of metal which screws into the Vulcanite stem. This extension on the earlier pipes will be of brass and the newer pipes will be of aluminium. Most smokers not knowing this function of the metal extension, assumes that it is a condenser/stinger and will remove it as they do with the metal condensers of Kaywoodie, etc. Should you have a System pipe with this metal extension, do not remove it for it will make the System function properly and give you a dryer smoke (https://pipedia.org/wiki/A_closer_look_at_the_famous_Peterson_Standard_System_Pipe).

With that information in hand I knew what I was dealing with in terms of the stamping and the age of this pipe. I knew from the information that the pipe was made during the Republic Era between 1950 and 1989. My guess is that the pipes is a 1960s era System pipe. Now it was time to work on the pipe.

Jeff cleaned this filthy pipe with his usual clean up process. This one was a real mess and I did not know what to expect when I unwrapped it from his box. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks very good with great looking grain around the bowl and shank. Jeff soaked the stem in Briarville’s Pipe Stem Deoxidizer to remove the oxidation on the vulcanite. When the pipe arrived here in Vancouver for the second stop of its restoration tour I was amazed it looked so good. I removed the incorrect stem and replaced it with a correct P-Lip stem for a 307 that I had here in my box of stems. The bonus was that the tenon had a brass chimney in the end that was correct for this pipe.I put the stem in the pipe and took photos of it with the correct stem. I liked the look of the pipe at this point in the process. I took some close up photos of the rim top and also of the stem surface. I wanted to show what an amazing job Jeff did in the cleanup of the rim top. The rim top was and inner edge were in excellent condition. I also took close up photos of the replacement stem I put in the shank to show the condition of the vulcanite. It was quite clean other than some slight oxidation at the edges of the button. There were no tooth marks or chatter on the stem surface.One of the things I appreciate about Jeff’s cleanup is that he works to protect and preserve the nomenclature on the shank of the pipes that he works on. The stamping on this one was very faint to start with so I was worried that it would disappear altogether with the cleanup. He was not only able to preserve and maintain its condition in the process. I took some photos to show the clarity of the stamping. I have noticed that many restorers are not careful to protect the stamping in their cleaning process and often by the end of the restoration the nomenclature is almost destroyed. I would like to encourage all of us to be careful in our work to preserve this as it is a critical piece of pipe restoration! I took the stem off the shank and took a photo of the pipe. I decided to start my work on the pipe by cleaning up some of the polishing compound left in the rustication ahead shank rustication ahead of the ferrule. I worked the end over with a brass bristle wire brush to remove the crud in the finish. The photos show the progress. I rubbed the bowl and rim down with Before & After Restoration Balm. I worked it into the rusticated surface of the briar with my fingertips and a horse hair shoe brush to clean, enliven and protect it. I let the balm sit for 10 minutes and then buffed with a cotton cloth to raise the shine. I really like watching the Balm do its magic and bring the briar alive. With briar polished with the Restoration Balm I moved onto the metal. I polished the nickel ferrule with a jewellers cloth to raise the shine and to protect the ferrule from further oxidation. I sanded the stem with 220 grit sandpaper to remove the oxidation that remained in the vulcanite and also the light tooth marks on the top and underside near the button. I started polishing it with 400 grit wet dry sandpaper.I touched up the “P” logo on the left side of the saddle stem with white acrylic fingernail polish. I let it dry then I polished off the excess with a worn 1500 grit micromesh sanding pad. Once the excess was removed the stamp looked much better even though there was some faintness on the curve of the P.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the stem down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I gave it a coat of Obsidian Pipe Stem Oil. It works to protect the stem from oxidizing. I set it aside to dry. Once again at this point in the restoration process I am excited to be on the homestretch. I look forward to the final look when the Rusticated Peterson System XL307 is put back together, polished and waxed. I put the bowl and stem back together. I lightly polished the bowl and stem with Blue Diamond to polish out the scratches in the briar and the vulcanite. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The depths of the rustication really pop with the wax and polish. The shiny black vulcanite stem is a beautiful contrast to the browns of the bowl and thick shank and nickel ferrule. This Peterson’s System Standard XL307 Bent Billiard was another fun pipe to work on. It really is a quite stunning piece of briar whose shape follows the flow of the briar. The pipe is tactile in the hand and should feel great as it is warmed up when smoking. The finished pipe is shown in the photos below. The dimensions of the pipe are Length: 6 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 2.26 ounces/64 grams. I will be putting it on the rebornpipes store in the Irish Pipemakers Section if you would like to add it to your rack and carry on the previous pipeman’s legacy. This is an interesting estate to bring back to life.

On My Diversionary Pipe Hunt I Found this French Made Lotus Bent Billiard

Leave a reply

Blog by Steve Laug

The next pipe on the table was second pipe I found on a recent trip to Alberta. I had a couple of hours to kill so I stopped at an antique mall along the way. The first was an Italian made cross grained Molina Bent Billiard that I already restored (https://rebornpipes.com/2023/09/27/took-a-diversionary-pipe-hunt-and-found-this-molina-81007-bent-billiard/). The second pipe I found was a French Made Bent Billiard. It was time to work on the second one now. On the left side of the shank it is stamped Lotus in script, underlined [over] Made in France. The pipe was in dirty condition. The finish on the bowl and shank were coated with a thick coat of grime and oils ground into the surface. There were many fills in the bowl sides, heel and the shank. The bowl had a thick cake that overflowed with a thick coat of lava on the rim top that obscured the inner and outer edges of the bowl. There appeared to be some damage on the front outer edge of the bowl. The black, hard rubber stem had an orific button and there was the beginning of a slot being shaped points to an older pipe. It was dirty and had tooth marks and chatter on both sides ahead of the button. There were small white paint spots on the shank and the stem. I took photos of the pipe before I started my clean up work on it to give a clear photo of the condition of the pipe before I started my work. I took a photo of the bowl and the rim top. The bowl had a thick cake that covered the bowl walls and bottom. The rim top and the bevelled inner edge of the bowl had a thick lava overflow. There appeared to be some damage on the front outer edge of the bowl. It was hard to know for sure what was underneath until it was cleaned. The hard rubber stem shows light tooth marks and chatter on both sides ahead of the button as mentioned above. There were paint spots on the stem top and sides. It had promise but it was dirty!I took a photo of the left shank side to try to capture the stamping on the briar. It is clear and readable as noted above. I removed the stem from the shank and took a photo of the parts to give a sense of the pipe’s proportions.I dropped a message to Kenneth Lieblich about the pipe because of his love of French Made Pipes and his work on gathering information on them. He wrote me back with the following helpful hint.

I think Lotus was a line of Delacour Brothers. Delacour closed around 1960, so if it’s one of their pipes, it must be older than that.

He wrote back with some more information as well:

Very little, but there’s a possible tidbit. There is a lighter company called Lotus, but I don’t think that’s related. However, my tidbit is a tobacco shop in Paris called “Le Lotus”. It’s been there for a while, but I haven’t yet figured out how long. That seems like a possibility, however tenuous. It’s also possible that it’s a second from one of the big French companies, but I don’t have a listing for it.

Also, there was a Lotus brand made by Delacour Bros. — that might be the most likely. The St Claude branch of Delacour, not the London branch.

I started by looking up the tobacco shop in Paris that Kenneth referred to “Le Lotus”. I found the shop in Paris and it looks to be an amazing shop with a huge selection of cigars. It is an old style tobacco shop and I suppose it could have some pipe tobacco but there were no photos showing any available. It is still a shop that I would love to visit one day that is for certain.

I agreed with Kenneth’s suggestion that the pipe is probably made by the St. Claude brandch of Delacour. I decided to do some digging to see if I could find information that definitively linked the Lotus pipe to Delacour.

I turned first to Pipephil to see what I could learn (http://www.pipephil.eu/logos/en/logo-d4.html). It gave a brief history of the brand and link to both the French and British activities of the company. I have included a screen capture of the pertinent section and the comments from the side bar below. Delacour pipes were crafted in the St Claude (14 bis rue Carnot) factory. The brand was founded in the late 19th century by Alix Delacour and owned a subsidiary company in London. Their activities stopped in the late 1950s.

From there I turned to look up the brand on Pipedia (https://pipedia.org/wiki/Delacour). There was very little included in the article. In fact, it gave a very brief history and a link to the company website. I quote the article in its entirety below.

The Delacour factory was built around 1892 and expanded in 1893) in Saint-Claude, Jura, France, Rue Carnot 14 bis.

The owner was Alix Delacour. Already in 1909 the factory was further expanded. Delacour had their own briar drying facilities. In 1960, the pipe factory closed. (Brand name was probably taken over by Jeantet). The Delacour building harbored afterwards: an eye-wear company, dance school, restaurant, etc. There was not any direct mention of the Lotus brand in the material but the shape and the look of the pipe is much like the Delacour pipes. I am about 99% clear that the pipe is a Delacour pipe. Given that information it was time to work on the pipe itself.

I started my work by reaming the bowl with a PipNet pipe reamer to remove the thick cake on the walls so I could see what they looked like. I used a Savinelli Fitsall Pipe Knife to scrape off the remaining cake on the bowl walls. I followed that by sanding the walls of the bowl until they were smooth with 220 grit sandpaper wrapped around a piece of dowel. The bowl walls showed no checking or cracking which is remarkable. I cleaned off the rim top and bevelled inner edge carefully, wet sanding the rim top with a folded piece of 220 grit sandpaper. It cleaned up quite well. I also gently topped the bowl with 220 grit sandpaper on a topping board to minimize the damage on the top and outer edge of the bowl. I scrubbed the bowl down with a tooth brush and some undiluted Murphy’s Oil Soap to remove the grime and oils around the bowl and shank. I rinsed it down with warm water to remove the debris. I coloured in the fills with a Walnut stain pen then filled them in with a clear CA glue. There were nine fills around the bowl and also the rebuild of the damage on the front of the outer edge of the rim. I sanded the glue repairs to the fills with a folded piece of 220 grit sandpaper. I smooth them out so that the surface of the repairs was smooth and blended together. I touched up the repaired spots and the bevelled inner edge of the rim with a Walnut stain pen to prepare the bowl for restaining. I stained the bowl with Fiebing’s Cordovan aniline stain. I flamed it and repeated the process until I was happy with the coverage on the bowl.I wiped the bowl down with isopropyl alcohol on cotton pads to make the stain more transparent and still leave the repaired fills hidden. I worked on the finish around the rim top and bowl with micromesh sanding pads – 1500-12000 grit sanding pads to dry sand the briar. I wiped it down after each sanding pad with a damp cloth after each sanding pads. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips and a horsehair shoe brush. The product works to clean, enliven and protect the briar. I let the balm sit for ten minutes and then buffed with a cotton cloth to raise the shine. It was at that moment I remembered I had not cleaned the shank and stem. I turned to work on that now. I cleaned out the airway and mortise in the shank and the airway in the stem. I used 99% isopropyl alcohol, pipe cleaners and cotton swabs to remove the tars and oils. It was extremely dirty and once cleaned smelled and looked better.I set the bowl aside and turned my attention to the stem. It was in decent condition with very light tooth marks. I polished the stem surface with micromesh sanding pads – 1500-12000 grit pads and was able to remove the marks. I wiped it down Obsidian Oil on a cotton cloth. I finished my polishing with Before & After Pipe Stem Polish – both Fine and Extra-Fine polishes. I wiped it down with a final coat of Obsidian Oil and set aside.I am excited to finish restoration of this Lotus Made in France Bent Billiard. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with beautiful mixed grain all around it. I love the look of the polished grain on the pipe with the polished black hard rubber stem. It is a very beautiful looking pipe. This smooth Lotus Bent Billiard is great looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 4 ½ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ inch, Chamber diameter: ¾ of an inch. The weight of the pipe is 33 grams/1.16 ounces. It turned out to be a beautiful pipe. I will be putting it on the rebornpipes store in the French Pipemakers Section soon. If you are interested in adding it to your collection let me know. Thanks for reading this blog and my reflections on the pipe while I worked on it.

Breathing New Life into a Stunning Ben Wade Danish Canadian

1 Reply

Blog by Steve Laug

The next pipe on the table is another that came to me for restoration from a friend in the US. He sent three pipes for me to restore for him. I finished the restoration of the first of these – a 1913 GBD 347 Straight Apple (https://rebornpipes.com/2023/09/23/breathing-life-into-a-1913-mrco-gbd-london-england-347-apple/). I am turning to the second one he sent, a beautiful Ben Wade Connoisseurs Collection First Edition Long Diamond Shank Brandy with a saddle stem. That leaves the final one that I need to work on an interesting Ivarsson 389 Product Apple. All the pipes are gorgeous examples of pipe craft and all were incredibly dirty and showed various issues with their finishes. The stamping on the pipe was as follows. On the top left side of the long diamond shank it read Ben Wade in script [over] Connoisseur Collection [over] First Edition. On the left underside it is stamped Hand Made [over] In [over] Denmark. On the right side it was stamped Reg. No. 80343. My guess is that this is a Ben Wade made by Preben Holm during the time Dunhill had him making Freehands for them. The pipe was in dirty condition. The finish on the bowl and shank were worn and dirty with grime and darkening ground into the surface all around the bowl and shank. The cake in the bowl was very thick – so much so that I could not put my little finger into the bowl. The lave flowed over the rim top and inner and outer edges of the bowl. It seemed to be in fair condition under the lava but cleaning would tell the story. The vulcanite diamond saddle stem had a crown logo on the top of the diamond. The stem was dirty and had file marks/sanding marks and tooth marks and chatter on both sides ahead of the button. I took photos of the pipe before I started my clean up work on it to give a clear picture of the condition of the pipe before I started my work. I took a photo of the bowl and the rim top. The bowl had a very thick cake on the walls and bottom. I was not able to even put my little finger in the bowl. The rim top and the inner edge of the bowl showed some nicks and a thick lava overflow. There also seemed to be some burn marks on the inner edge. It was hard to know for sure what was underneath but I would be there would be some darkening. The vulcanite stem shows some deep tooth marks and chatter on both sides ahead of the button as mentioned above. There were also some file or coarse sandpaper marks. It had promise but it was dirty!I took photos of the shank sides to try to capture the stamping on the briar. I took photos of the stamping on the right top side, underside and right top side of the diamond shank. It was clear and readable. I removed the stem from the shank and took a photo to get a sense of the length of the shank and overall look of the pipe. It is a beauty!I did a Google search on the Ben Wade Connoisseur Collection [over] First Edition and found two listings on Worthpoint (an auction site). The first included the pipe, the hand made case and the certificate of authenticity (https://www.worthpoint.com/worthopedia/ben-wade-pipe-preben-holm-connoisseur-521474453). Make sure to read the certificate as it clearly states that Preben Holm made the pipe under the auspices of Ben Wade. The First Edition was limited to 504 pipes. Theoretically a second edition etc. would follow. We know that Holm died in 1989 so it appears that there was only one edition of the pipe. That makes this a rather unique and very collectible piece.

I copied the advertisement on Worthpoint in full and included it below. The description of the pipe is quite amazing as is details on the shape, size, finish etc. I quote:

You are bidding on a special BEN WADE, ” CONNOISSEUR COLLECTION ” first limited edition series that was hand crafted by legendary pipemaker PREBEN HOM, in Denmark, in 1980. This pipe shows a darker reddish stain that nicely accentuates the well-defined birdseye and cross grain that cover the entire bowl and shank. Top of bowl is very clean and in excellent condition (please see pictures). The shank itself and the mouthpiece show a distinct diamond shape. Unique, ” Canted Danish Billiard ” shaped bowl with a 1/4 bent, diamond shaped shank. Part of a ” LIMITED EDITION ” series called ” Connoisseur Collection ” of distinctively shaped and numbered pipes. This is number 388 of a first series of only 504. There has never been a second edition of Ben Wade pipes. This is roughly the size (and capacity) of a Dunhill ODA sized pipe. Lovely grain textures, unique shape, great condition and overall quality artisanship! A very lovely piece and a very original play on an old classic! This pipe has been formerly lightly smoked and is in very good condition. A pipe cleaner passed through with ease. This pipe comes in its original presentation box, and with the original certificate. The pipe was cleaned, polished and taken care of by one of the oldest pipemakers in Montreal, now celebrating 107 years of pipe making (est. 1907)! Markings: The mouthpiece is the original (acrylic), shows the original Ben Wade “crown” and is in excellent condition (no marks …). Ben Wade CONNOISSEUR COLLECTION FIRST EDITION HAND MADE INDENMARK REG NO. 8021 ……(21st PIPE OF THE FIRST EDITION, 1980). Dimensions: Overall height of pipe: 2″ Length: 6 3/4″ Inner Diam. = 7/8″ Outer Diam. (top of bowl) = 1 3/8″ If there are any questions about this item or any other items presently available, please feel free to ask.

The second listing on Worthpoint (https://www.worthpoint.com/worthopedia/ben-wade-connoisseur-collection-first-486770771) was a second pipe with the same stamping other than the Reg. No. I have copied it below for the further information. In this article it says that Holm died in 1975 but he died in 1989. The other error it seems to my research that Ben Wade made the pipe in honour of Preben Holm. However, it seems that pipes were actually made or designed by Holm himself. I quote:

Bari Preben Holm died 1975 this pipe was made in his Ben Wade (Dunhill) era Wade Connoisseur Collection First Edition Reg.No.80353 Hand Made in Denmark that’s it!! This pipe is amazing good old times this pipe was made for collectors and lovers for a very good Danish pipe by Ben Wade to honour Preben Holm Hand Made unique birdseye smoked made without any number- means this pipe is unique. This pipe shows a smooth finish-no scratches no tooth marks very good condition for the age!!! Nearly 45years old!!High: 4,5 cm = 1,77 inch length: 17 cm = 6,68 inch smoked pipe comes cleaned with 96% alk x-mas is coming shipping with tracking number and insurance Austria : 6 €eu : 14€ = 18 $us and worldwide : 19 € = 25$i am a private seller: no returns no exchanges.Given those facts I can be certain that the pipe was made by Preben Holm in Denmark prior to his death in 1989. From the information above using the Reg. No. 80343 stamp we are given a method of dating the pipe. The pipe is thus the 34^th pipe of the first edition made in 1980. It is a limited collector series of pipes that combines a touch of freehand with a classic Danish Canadian. It was a way in which Dunhill could carve a niche for themselves in the burgeoning freehand market in the US. Now it was tie to work on the pipe.

I started my work on the pipe by reaming the bowl with a PipNet pipe reamer to remove the thick cake on the walls so I could see what they looked like. Strangely, I touched the cake with the tip of the cutting head and the cake crumbled out onto the paper. It was very soft and crumbly and I have never had an entire cake come out of the bowl with the first touch of the reamer. I used a KleenReem pipe reamer to clean up the bottom of the bowl and remove remnants of cake there. I followed that with a Savinelli Fitsall Pipe Knife to scrape off the bits of remaining cake on the bowl walls. I followed that by sanding the walls of the bowl until they were smooth with 220 grit sandpaper wrapped around a piece of dowel. The bowl walls showed no checking or cracking which is remarkable. I took a photo of the mountain of carbon that came out of the bowl with the reaming.I cleaned out the airway and mortise in the shank and the airway in the stem. I used 99% isopropyl alcohol, pipe cleaners and cotton swabs to remove the tars and oils. It was extremely dirty and once cleaned smelled and looked better.I decided to deal with the damage and darkening to the rim top and inner edge of the bowl next. I used a folded piece of 220 grit sandpaper to smooth out the nicks and damage on the edge. Once finished it looked much better. I cleaned up the damage to the rim top and thick lava coat with a piece of 220 grit sandpaper and a topping board. I lightly topped the bowl to remove the damage. I did not remove much briar at all, actually I removed the thick lava coat and smooth out the nicks and marks. That was my goal and I think it worked well. I touched up the stain on the rim top with a Walnut stain pen. It would even out as I polished and buffed it. I worked on the finish around the rim top and bowl with micromesh sanding pads – 1500-12000 grit sanding pads to dry sand the briar. I wiped it down after each sanding pad with a damp cloth after each sanding pads. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips and a horsehair shoe brush. The product works to clean, enliven and protect the briar. I let the balm sit for ten minutes and then buffed with a cotton cloth to raise the shine. I set the bowl aside and turned my attention to the stem. I painted the stem surface with the flame of a Bic lighter to lift the tooth marks. I was able to lift them quite a bit. I repaired what remained with some light spots of CA. I would have left them but the marks were large and needed to be addressed. I sanded out the repairs and blended them into the surface with 220 grit sandpaper. I stared polishing the stem with 600 grit wet dry sandpaper. I polished the stem surface with micromesh sanding pads – 1500-12000 grit pads. I wiped it down Obsidian Oil on a cotton cloth. I finished my polishing with Before & After Pipe Stem Polish – both Fine and Extra-Fine polishes. I wiped it down with a final coat of Obsidian Oil and set aside. I am excited to finish the restoration of this 1980s Preben Holm carved Era Ben Wade Connoisseur Collection First Edition Danish Canadian. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with beautiful mixed grain all around it. I love the look of the polished grain on the pipe with the polished black vulcanite stem. This smooth Ben Wade Connoisseur Collection Canadian is great looking and the pipe feels great in my hand. It is quite light for its size and well balanced. Have a look at it with the photos below. The dimensions are Length: 7 inches, Height: 2 ¼ inches, Outside diameter of the bowl: 1 ¼ inch, Chamber diameter: 7/8 of an inch. The weight of the pipe is 46 grams/1.62 ounces. It turned out to be a beautiful pipe. I will be sending it back to the pipeman who sent it to me once I finish the final remaining pipe. Thanks for reading this blog and my reflections on the pipe while I worked on it.

Sometimes I wish I had been alive in the time of the classic shops in North America – Breathing Life into an Ansell’s Wash.D.C. Saddle Stem Billiard

Leave a reply

Blog by Steve Laug

The next pipe on the work table was purchased on 05/21/22 from and Antique Store in Longview, Washington, USA. Both Jeff and I love hunting for pipes and we pick up quite a few pipes for restoration from shops on our travels. We work them into the restoration queue so that we can keep them moving. This is a beautifully grained Billiard with a vulcanite saddle stem. The pipe is stamped on the left side and reads 76 next to the shank bowl junction followed by the stamp IMPORTED BRIAR. On the right side of the shank it reads Ansell’s [over] Wash.D.C. The finish had a lot of grime ground into the smooth finish on the bowl and some darkening around the sides of the bowl. The bowl was thickly caked with an overflowing thick lava coat on the bevelled rim top and edges of the rim. The stem was lightly oxidized, dirty and had light tooth chatter and marks on the top and underside near the button. There were not markings or a logo on the saddle stem. It had promise but it was very dirty. Jeff took some photos of the pipe before he started his cleanup work. He took photos of the rim top and bowl to give a clear picture of the thickness of the cake and the overflow of lava on the rim top. He also took photos of the top and underside of the stem to show the light chatter and tooth marks. You can also see the light oxidation and calcification on the surface. Jeff took photos of the sides and heel of the bowl to give a picture of what the briar around the pipe looked like. There is some stunning grain under the build up of grime. He took photos of the stamping on the sides of the shank. It reads as noted above and is clear and readable. I turned to Pipedia to see if there was any information on the brand that gives me the background info that I enjoy as I work on a pipe (https://pipedia.org/wiki/Ansell%27s). I found a brief article and I quote it below in full.

Ansell’s Pipe and Tobacco store was at 820 14th St. NW in Washington D.C. It was one of three pipe brands I know of which are marked with Wash. D.C. The others are Bertram pipes and A. Garfinkel.

There was also a photo of a label and matchbook. Thanks to Doug Valitchka for his photo.From this information I learned that Ansell’s was a Pipe and Tobacco Shop in Washington DC and along with Bertrams and Garfinkel made and sold their own pipes. Previously, Jeff and I picked it up a group of pipes from a seller who had bought them at the closing auction of the Bertram’s Pipe Shop in 1970. Though this one came from a separate sale, I think that it is safe to assume that the pipe was made prior to that.

Jeff had cleaned up the pipe with his habitual process that delivers a very clean pipe to me for work. He reamed the pipe with a PipNet Pipe Reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He soaked the stem in Briarville’s Pipe Stem Deoxidizer and rinsed it off with warm water. I took photos of the pipe once I received it. The rim top cleaned up well with the lava coat removed. The inner edge of the rim had some burn damage on the left and back of the bowl with some darkening and burning on the rim top in the same places. The stem surface looked very good with a few small tooth marks and chatter on both sides near the button. I took photos of the stamping on the shank. There is a 76 stamped next to the shank/bowl junction followed by Imported Briar on the left side and Ansell’s in script [over] WASH.D.C. I left on trip around Alberta for work before working on the pipe. I decided to bring it along to work on in the evenings once work was finished. At the first hotel I started my work on the pipe. I removed the stem and took a photo of the pipe to give a sense of the whole. The saddle stem billiard is a nice looking pipe. The stem also has an aluminum stinger in the tenon.I brought along a bag with some 220 and 600 grit sandpaper and a set of micromesh sanding pads. Now it was time to do my work on the pipe. I took the pipe to the desk top in the hotel room and started my work. The bevelled rim top and the inner edge of the rim was damaged with burn marks and darkening. I used a folded piece of 220 grit sandpaper to clean it up and remove the damage. It looked significantly better. Once I had cleaned up the bevelled rim top and edges I polished the bowl and the rim top, sides and shank with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiping it down after each pad with a damp cloth. At that point my trip was over and I returned to Vancouver. After a good night sleep I got up in the morning and returned working on the pipe. I used a Walnut stain pen to touch up the stain on the bevelled rim top and rim edges. I stained it and set it aside to cure.I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for about ten minutes and then buffed it off with a cotton cloth to raise the shine. I set the bowl aside and turned to work on the stem. I heated the stinger and twisted it free of the shank. It was pressure fit in the tenon and the tars and oils held it tight in place. I used a pair of needle nose pliers to carefully twist it free. I cleaned the tenon area after it was removed but it was not too dirty.I polished the tooth marks and chatter out of the vulcanite stem surface with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I finished my polishing with Before & After Pipe Stem Polish – both Fine and Extra-Fine polishes. I wiped it down with a final coat of Obsidian Oil and set it aside.I pressed the stinger back in the tenon. It is simple to remove so if the new owner does not want it in place he/she can remove it.This Ansell’s Wash.D.C. Imported Briar Billiard with a vulcanite saddle stem is a great looking pipe now that it has been restored. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Ansell’s Saddle Stem Billiard fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¼ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe 1.20 ounces/34 grams. I will be putting it on the rebornpipes store in the American Pipe Makers Section soon. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

New Life for a Bastia Billiard 408 made by Lillehammer Pipes Norway

1 Reply

Blog by Steve Laug

The next pipe I have chosen is an elegant Danish Straight Billiard with a mix of grain around the bowl and shank. This particular pipe came to us from a fellow in Copenhagen, Denmark on 11/14/2022. This Billiard was stamped on the left side of the shank and read Bastia [over] GL. It was stamped on the underside with the shape number 408. The pipe was in filthy condition when Jeff brought it to the table. The finish was dirty with oils and grime ground into the briar sides and rim. The bowl had a thick cake and some darkening on the inner edge of the rim. There was a lava coat flowing on to the rim top from the bowl – heavier on the back side than the front but very present. The stem was dirty – oxidized and calcified with light tooth marks and chatter on the top and underside ahead of the button. There was no stamp or identifying mark on the stem. Jeff took photos of the pipe before his cleanup work. They tell the story and give a glimpse of the promise that we see in this pipe. Jeff took photos of the rim top and stem to show the general condition of the pipe. The bowl showed some thick cake and some darkening on the inner edge. The rim top had a thick coat of lava on the surface, heavier on the back and right side of the top. The photos of the stem show the oxidation, calcification, tooth marks and chatter on both sides near the button. Jeff took some photos of the bowl sides and heel to show the beautiful grain that was around this bowl. It is a nice looking pipe. He took photos of the sides of the shank to show the stamping. The stamping is readable in the photos below and is as noted above. I am including the information from Pipephil on Lillehammmer pipes. It connects to the Bastia in sharing the GL initials under the brand stamp (http://www.pipephil.eu/logos/en/logo-l4.html). I have included a scan of the section on Lillehammer. You can see that the GL stamp are the initials of Gudbrand Larsen the founder of Lillehammer.I turned to the Pipedia site for more information (https://pipedia.org/wiki/Lillehammer). There I was able to learn the backstory and history of the brand. I quote in full from that article and include pictures of the two principals.

In the 1830’s a young Norwegian wood-carver named Gudbrand Larsen saw some pipes made from meershcaum. He though they were beautiful and wanted to make pipes like that, but he could not obtain the material. So he decided to go where it was to be found.

Gudbrand Larsen 91815-1902)

Larsen went to Eskisehir, Turkey, to learn all about meerschaum. But the most beautiful pipes in those days were not made there but in France, so he continued his journey to Marseielle, where he found work in one of the most famous factories at the time. In 1844 he returned to Norway and started a small factory for meerschaum pipes in the town of Lillehammer. The pipes garnered a good reputation from the first.

Gudbrand’s son, August, followed in his father’s footsteps and joined him in the business. However, father and son did not get along very well, so Junior–as August usually was called–did like his father once had, he traveled to learn more about pipe-making.

Martin August “Junior” Larsen (1855-1915)

Junior understood that briar, not meerschaum, was the material of the future, so during his journey he studied the subject carefully, first in England and then in France.

In Paris Junior earned a position with a pipemaker of good repute and became highly respected in his work. However, Gudbrand was getting old and considering retirement, so he asked his son to come home and take over the family business, an offer Junior willingly accepted. As a businessman Junior was even more successful than his father, and during his period of leadership the business prospered.

In 1902 Gudbrand Larsen died at almost 90 years of age. Then Junior passed away a dozen years later, in 1914. His death was followed by some unstable years for the factory because it lacked competent management. And World War I had just started on the continent, which made it difficult to obtain raw material.

In 1916 the factory was bought be a company that appointed new management, and a long, stable period of successful expansion had begun. That period was to last for almost half a century. The main part of the production was briar pipes, but they also continued to make some meerschaums.

Problems at the factory began again at the end of the 1960s, when sales slowed dramatically. The main reason was the “fancy pipes” had become very popular, and Larsen’s of Lillehammer had nothing to offer there. Something had to be done and two steps were taken. In the middle of the 1970s the Danish company Kriswill was bought, and in that way they obtained access to that company’s more modern shapes. A new designer was also employed, but these efforts were not sufficient, and in the 1979 the factory closed.

I turned to the Pipe Club of Sweden site to see if there was any more information. There was a great article on the pipe maker Bård Hansen who followed the tradition of the Lillehammer Factory and was trained by a retired engineer from the Lillehammer Factory thus tying him to the brand. In that article there is confirmation for the Pipedia information above (http://www.svenskapipklubben.se/en/pipemakers/bard-hansen/). I quote in part the article there by Jan Andersson. (Once again I have highlighted the pertinent information in the text below using bold, italic and underlined text and marking the main point highlighted in red.

In a Swedish tobacco shop, even in small places in the province, there were usually a fair number of pipes in the 50s and 60s with stems from aluminum. But even for the more traditional pipesmoker, who wanted a pipe from wood and ebonite, there was a lot to choose from. Ratos was the dominant brand, but for those who were willing to spend a little extra, there were usually at least a few more exclusive pipes – pipes in green or blue-checked boxes. Those pipes came from Norway, from G.L. Larsens pipe factory in Lillehammer.

Lillehammer pipes were found in two qualities, Bastia was a little cheaper and Lillehammer GL was for the truly discerning pipesmoker. Later I have learned that there were also more expensive and finer qualities, even one called Best Make, but those luxury pipes were never found in the shops in the small town where I lived. Lillehammer pipes were easily recognizable, they usually were rather slim and with a long stem, which was the fashion at the time. So while a true English gentleman smoked a Dunhill with the white dot on the stem, Norwegian or Swedish pipesmokers preferred an elegant Lillehammer.

We will not go into detail about the interesting story of Lillehammer, but unfortunately we can see that from the beginning of the 70s, it rapidly went downhill for the factory. They bought the Danish company Kriswill but that was not a success, nor was the new series of shapes created by the pipemaker Thorbjørn Rygh. So G.L. Larsen’s pipe factory in Lillehammer had to close, deeply missed by many of us. This feeling persists to this day, which is particularly evident in the great interest in the Lillehammer pipes at auctions and collector’s markets.

Gathering the data together from my research I have learned that the pipe I have on my worktable is made by Lillehammer prior to the buy out by the Kriswill Company with the hope that it would offer new markets for the Lillehammer brand. The Bastia was the cheaper of the lines and interestingly it also bears GL stamping tying it to the higher end pipes from the factory.

Armed with that information I turned to address the pipe itself. Jeff had cleaned up the pipe for me. He reamed the bowl with a PipNet pipe reamer and cleaned it up with a Savinelli Fitsall Pipe Knife. He scrubbed the exterior with Murphy’s Oil Soap and a tooth brush to clean off the grime off the finish and the heavy overflow of lava on the rim top. He cleaned up the internals of the shank, mortise and stem with pipe cleaners, cotton swabs and alcohol to remove all of the oils and tars in the pipe. The rim top still had some darkening that would need to be dealt with but it looked good. He soaked the stem in Briarville’s Pipe Stem Deoxidizer and was able to remove the remnants of the oxidation. When it arrived here in Vancouver it was a clean pipe and I knew what I had to work with. I took photos of it before I started my part of the restoration. The rim top had cleaned up pretty well but you can see the darkening on the inner edge. The burn damage on the rim top and edge at the back right of the bowl. The stem cleaned up very well. You can see the tooth marks on the surface just ahead of the button. I took photos of the stamping on the sides of the shank. You can see that it is stamped as noted above. It is clear and readable. I removed the stem and took a photo of the pipe to have a look at the parts and overall look.I decided to address the damage to the rim top and inner edge of the bowl first. I used a folded piece of 220 grit sandpaper to give the inner edge of the bowl a slight bevel on the inner edge to remove burned areas and blend them into the surrounding briar. I polished the bowl and shank with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I wiped down the bowl after each pad with a damp cloth to remove the sanding debris. I worked some Before & After Restoration Balm into the surface of the bowl and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned my attention to the stem. I filled in the deep marks black CA glue. Once it cured I used a file to flatten them and start blending them into the surface of the surrounding vulcanite. I sanded the repaired areas with a folded piece of 220 grit sandpaper. I started polishing it with 600 wet dry sandpaper. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished polishing the stem with Before & After Pipe Stem Polish – both Fine and Extra Fine. I wiped the stem down with a final coat of Obsidian Oil and let it sit and absorb into the vulcanite. I am excited to finish this Bastia GL 408 Billiard made by Lillehammer. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with beautiful cross and birds eye grain all around it. Added to that the polished black vulcanite stem combined with the bowl made a stunning pipe. This smooth Norwegian Bastia GL 408 Billiard is great looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 6 ¼ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 34 grams/1.20 ounces. It is a beautiful pipe that I will soon be putting on the rebornpipes store in the Danish Pipe Makers Section. If you are interested in adding it to your collection send me an email or a message. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.

Replacing a Snapped Tenon on a Neerup of Denmark Freehand Style Bulldog

1 Reply

Blog by Steve Laug

The next pipe on the table came to me from Curtis, a customer I have repaired pipes for in the past. He sent me two pipes that he wanted repaired by mail. I started with this one first. In looking at it I recalled that I had restemmed this pipe for him in December of last year. The original stem had been badly damaged and I had replaced it with the current stem and cap to give it a look similar to the original. It was a lot of work but I liked how it looks. Here is the link to that restoration (https://rebornpipes.com/2022/12/22/new-life-and-new-look-for-a-neerup-made-in-denmark-bulldog/). It was a nicely shaped sandblasted Bulldog with a black acrylic and a white acrylic spacer on the shank end. There was a snapped tenon in the shank and a vulcanite taper stem with a silver metal end cap/band. The tenon had snapped smoothly against the metal stem band. I would need to clean it up and replace the tenon. The bowl had a thick cake of a vanilla smelling aromatic and a thick overflow of lava on the inner edge and the rim top. The rim top was slightly worn and smooth under the lava. The stem had some calcification, tooth chatter and marks on the surface of the top and underside ahead of the button. I took some close photos of the bowl, rim top and the stem to show their condition when I started working on it. You can see the thick cake in the bowl and the thick lava coat on the rim top and inner edge. It is quite heavy and the overflow obscures the condition of the edge of the bowl and the rim top. I was able to start pulling the broken tenon and you can see it extending out of the shank. I started my work on this pipe by pulling the broken tenon from the shank. I used a drywall screw and threaded it into the airway in the tenon piece. When it took hold, I wiggled the tenon free from the shank. It took a bit of careful and slow work to loosen and remove it. I went through my box of tenons looking for one that was the proper size for the shank. Ideally it would have been a black threaded tenon but I did not have any that were the proper diameter. I did have some white Delrin tenons that were perfect and would work with the white acrylic space. The lower one in the photo would be perfect. I reduced the diameter of the threaded portion with my Dremel and a sanding drum. I used a flat file to smooth out the transition and further shape the new tenon. I used a folded piece of 180 grit sandpaper to remove the sanding marks and clean up the diameter of the tenon.When I finished the sanding, I polished it with 220 and 600 grit sandpaper to smooth out the surface. Once finished, it fit perfectly in the shank of the pipe. I left threads on the insert portion of the new tenon so that the glue would have something to grab onto when it was inserted in the stem. I removed the new tenon from the shank and turned my attentions to the stem. I drilled out the airway with a succession of larger drill bit – beginning with one slightly larger than the airway in the stem and ending with an 11/64ths drill bit.Once it had been opened up I pushed the tenon in the shank once more and slid the stem over the top to align it. The fit was very snug and nice. I took photos of it to show the fit at this point in the restoration process. I removed the stem from the pipe and the tenon from the mortise. I turned my attention to cleaning the internals and the externals of the bowl and shank. I reamed the bowl with a PipNet pipe reamer and the number three cutting head. I took the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall pipe knife to remove what remained. I sanded the walls of the bowl with 220 grit sandpaper wrapped around a piece of dowel. Once finished the bowl walls were smooth and clean. I scraped off the lava on the rim top with the edge of a Savinelli Pipe Knife and then used a brass bristle wire brush to remove the debris. I scrubbed the exterior of the bowl with a tooth brush and undiluted Murphy’s Oil Soap. I used the brass bristle brush to work over the rim top with the soap to go more deeply in the sandblast surface of the rim. I cleaned out the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. I worked on them until the mortise and airway in the shank and stem were clean.Before gluing the new tenon in place in the stem I went over the stem with a lens. I saw a crack in the stem side on the left. It must have happened when the tenon snapped in the shank. I removed the metal band/cap on the stem end and dabbed some clear CA glue in the cracked area and worked it into the crack with a tooth pick. I put some white glue in the inside of the cap and pressed it back onto the stem end. The crack was solidly repaired and the cap and band held it together.I touched up the rim top and edges with a Walnut and a Black stain pen to blend colour of the clean surface into the colour of the rest of the bowl and shank.I worked some Before & After Restoration Balm into the surface of the bowl and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned my attention to the stem. I sanded the stem surface with a folded piece of 220 grit sandpaper. I started polishing it with 600 wet dry sandpaper. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished polishing the stem with Before & After Pipe Stem Polish – both Fine and Extra Fine. I wiped the stem down with a final coat of Obsidian Oil and let it sit and absorb into the vulcanite. This Neerup Made in Denmark Freehand Bulldog carved by Peder Jeppesen combines a great looking piece of sandblast briar with a multi-banded shank extension and a vulcanite stem to make a beautiful pipe. The clean up work brought back the shiny coat allowing the grain to come alive with the polishing and waxing. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Neerup Made in Denmark Bulldog really is a beauty and fits nicely in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 1/2 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.80 ounces/51 grams. Once I finish the second pipe this one will be going back to Curtis to enjoy. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

This Interesting Maltese Lovat has quite a history

Leave a reply

Blog by Steve Laug

The next pipe I have chosen is a classic British looking Lovat shape. This particular pipe had a very dirty/grimy finish and some peeling varnish. It had some nice grain around the bowl sides and shank underneath the grime and peeling finish. It came to us from an antique store in Vancouver, Washington, USA on 10/20/2022. How it travelled from Malta, an island country in the Mediterranean, to the west coast of the US to an antique shop in Vancouver, Washington is a story I would love to learn more about. But that is a mystery that shall remain with this speechless pipe. The Lovat was stamped on the left side of the shank with a Maltese Cross. On the right side it is stamped Made in Malta. The pipe was in filthy condition when he brought it to the table. The finish was dirty with oils and grime ground into the briar sides and rim. The bowl had a thick cake and a heavy lava overflow on to the rim top. It was hard to know what the inner edge of the rim looked like under the grime. The stem was dirty with some light oxidation or calcification on it ahead of the button. There were light tooth marks and chatter on the top and underside on and near the button. There was also a bite through on the underside of the stem ahead of the button. There was not a logo stamped on the stem. Jeff took photos of the pipe before his cleanup work. They tell the story and give a glimpse of the promise that we see in this pipe. Jeff took photos of the rim top and stem to show the general condition of the pipe. The bowl had a heavy cake and a thick coat of lava on the rim top. It was hard to know what the inner edge looked like at this point but we would know after clean up. The photos of the stem show the tooth marks and chatter on both sides near the button. You can also see the small bite through on the underside of the stem near the button. Jeff took some photos of the bowl sides and heel to show the grain showing through the brown stain and the peeling varnish that was around this bowl. It is a pipe with some great potential. He took photos of the sides of the shank to show the stamping. The stamping is readable in the photo below and is as noted above. I looked on Pipedia to see if there was any information on the brand. It was listed under the article for the Briar Pipeworks Ltd. (https://pipedia.org/wiki/Briar_Pipeworks_Ltd.). There was not a lot of information on the brand there but it was helpful. I quote it in full below. I highlighted in bold the stamp on this pipe – Maltese Cross.

The Briar Pipeworks Ltd. (or Malta Pipes as they call themselves) is situated in Marsa, Malta and produces hand finished medium priced pipes. The company was founded in 1933 and specializes in Briar and Maltese Olive wood pipes in a vast range of models. They also produce custom made engraved pipes.

The current number of employees is said to be three.

Some brands / models made by Malta Pipes are:

Big Bill
Boschetto (olive wood)
Calypso
Champion
Comino
Darville (churchwarden pipe)
Dr. Stewart “Safety Smoke”
Filfla
Grandmaster
Maltese Cross
Mayfair
Portland Pipe

Jeff had done a great job cleaning up the pipe as usual. He reamed the pipe with a PipNet reamer and cut back the cake back to the bare briar. He cleaned up the walls with a Savinelli Fitsall Pipe Knife. He scrubbed the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol to remove the tars and oils. He scrubbed the exterior of the pipe with Murphy’s Oil Soap and a tooth brush to remove the grime from the finish. He scrubbed the bowl with acetone to remove the peeling finish. He worked on the rim top lava and the darkened spots with the soap and tooth brush. He scrubbed the inside of the stem with alcohol and pipe cleaners. He scrubbed the exterior with Soft Scrub and then soaked it in Briarville Pipe Stem Deoxidizer. He washed it off with warm water to remove the Deoxidizer. The pipe looked far better when it arrived. The rim top had cleaned up pretty well but you can see the burn damage to the inner edge. The backside of the bowl is worse than the rest of the edge. There scratches and nicks in the surface of the rim top. The stem cleaned up very well. You can see the deep tooth marks on the surface ahead of the button and the bite through on the underside of the stem ahead of the button. It was going to take a bit of work to clean it up and repair it.I took photos of the stamping on the sides of the shank. You can see that it is stamped as noted above. It is clear and readable. I removed the stem and took a photo of the pipe to have a look at the parts and overall look. I decided to address the damage to the front rim top and inner edge of the bowl first. I used a folded piece of 220 grit sandpaper to give the inner edge of the bowl a slight bevel on the inner edge to remove burned areas and blend them into the edge. I used an Oak stain pen to stain the bevel to match the surrounding briar.I polished the bowl and shank with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I wiped down the bowl after each pad with a damp cloth to remove the sanding debris. I worked some Before & After Restoration Balm into the surface of the bowl and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned to work on the stem. I decided to deal with the bite through in the stem surface. I greased a pipe cleaner with Vaseline and inserted it in the airway in the button under the bite through. I filled in the hole with black CA glue. I set it aside to let the repair cure. Once the repair cured. I flattened it with a file to start the blending process. I continued that process with a folded piece of 220 grit sandpaper to smooth it out. I started the polishing process with 600 grit wet dry sandpaper. It was looking much better and the bite through was gone. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil.I finished polishing the stem with Before & After Pipe Stem Polish – both Fine and Extra Fine. I wiped the stem down with a final coat of Obsidian Oil and let it sit and absorb into the vulcanite.I am excited to finish this Made in Malta Maltese Cross Lovat. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with beautiful mixed grain all around it. Added to that the polished black vulcanite stem combined with the bowl made a stunning pipe. This smooth Classic Lovat shaped Maltese Cross is great looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 31 grams/1.09 ounces. It is a beautiful pipe that I will soon be putting on the rebornpipes store in the Pipes from Various Makers Section. If you are interested in adding it to your collection send me an email or a message. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.

Restemming JSP (Joel Shapiro) Stack that came with a misfit stem

Leave a reply

Blog by Steve Laug

The next pipe I have chosen is large, tall bent stack with a poorly fit long Churchwarden stem. The diameter of the shank is not even close to the stem diameter. It appears to me that someone had added the stem solely to create their own long stem smoke. The shank end was a bit damaged on the on the face of the stem. I would need to do something to deal with that when I worked on it. This particular pipe had a very dirty/grimy finish but had some nice grain around the bowl sides and shank underneath the dark reds and black stem. It came to us from a fellow in Copenhagen, Denmark on 01/26/2023. This Bent Stack was stamped on the underside of the shank and read JSP. There were no other stamps on the shank sides. The pipe was in filthy condition when he brought it to the table. The finish was dirty with oils and grime ground into the briar sides and rim. The bowl had a thick cake and some darkening on the inner edge of the rim. There was some light lava on the rim top. The misfit stem was dirty but there was no oxidation or calcification on it. There were light tooth marks and chatter on the top and underside on and near the button. There was not a logo stamped on the stem. The diameter of the shank was significantly larger than that of the stem. Jeff took photos of the pipe before his cleanup work. They tell the story and give a glimpse of the promise that we see in this pipe. Jeff took photos of the rim top and stem to show the general condition of the pipe. The bowl showed some moderate cake and some darkening on the inner edge. The rim top looked quite clean with small specks of lava on the surface. The photos of the stem show the light tooth marks and chatter on both sides near the button. Jeff took some photos of the bowl sides and heel to show the grain showing through the black and red stain that was around this bowl. It is a nice looking pipe. He took a photo of the underside of the shank to show the stamping. The stamping is readable in the photo below and is as noted above. He took a photo of the fit of the stem against the shank end. You can see the difference in the diameter of the stem and the shank as well as some of the nicks and marks in the shank end. I turned to a blog I wrote recently about a JSP pipe. That one was a Bamboo shank poker that was quite beautiful. Here is the link to that blog (https://rebornpipes.com/2023/07/13/restoring-an-american-made-jsp-7-bamboo-shank-poker/). I quote from that blog now in the section on the background to the brand.

I turned to Pipedia to have a look at the history of the brand. I was pretty sure it was made by Joel Shapiro but needed confirmation (https://pipedia.org/wiki/JS_Pipes). Here is the information from the article.

Welcome to JS Pipes! http://www.jspipes.com

Let me introduce myself. My name is Joel Shapiro, and I live in Rancho Cordova, California. I offer a limited number of handmade briar pipes for sale.

The type of briar (Grecian, Italian, etc.) will be noted for each pipe made, along with further details concerning stem type (ebonite, lucite, cumberland, etc.) and shank extensions. A complete size description will be included with each pipe posted for sale.

I do not fill any flaws in the briar, so the buyer will see exactly what is offered with nothing to hide. All pipes are finished with a buffed in coat of carnauba wax over the stain. Stains are all alcohol based and will not seal the wood, so won’t alter the smoking experience or the breathing qualities of the briar.

In addition, I also offer a unique tamper design. My tampers are hand turned from quality hardwoods and the foot is cut at an angle to aid in mounding the tobacco and keeping the ember banked. I have found that this design results is fewer relights for a more enjoyable smoke. I can make these in any custom size and in most hardwoods, including some exotics. If you’d like a custom size (for very large pipes for example) or material, please contact me at jspipes@jspipes.com. All tampers are priced at $24.95, unless the material chosen is particularly expensive or difficult to work.

If you’d like to buy a pipe or tamper, but prefer to pay by money order or check, please e-mail (jspipes@jspipes.com) for my mailing address.

Would you like an email when new pipes are posted? Send me an e-mail and request to be on the JS Pipes mailing list! jspipes@jspipes.com

Jeff had done a great job cleaning up the pipe as usual. He reamed the pipe with a PipNet reamer and cut back the cake back to the bare briar. He cleaned up the walls with a Savinelli Fitsall Pipe Knife. He scrubbed the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol to remove the tars and oils. He scrubbed the exterior of the pipe with Murphy’s Oil Soap and a tooth brush to remove the grime from the finish. He worked on the rim top lava and the darkened spots with the soap and tooth brush. He scrubbed the inside of the stem with alcohol and pipe cleaners. He scrubbed the exterior with Soft Scrub and then soaked it in Briarville Pipe Stem Deoxidizer. He washed it off with warm water to remove the Deoxidizer. The pipe looked far better when it arrived.I went through my can of stems until I found the one that fit the angles and the diameter of the shank. I used a Dremel and sanding drum and a file to reduce the diameter of the tenon on the new stem to fit the shank. Now it was time to deal with the damage on the shank end. I decided to use a thin brass band to provide a smooth base for the new stem to sit against. I gave the shank end a thin coat of white all-purpose glue and spread it with a tooth pick. I pressed the band in place on the shank and wiped off the excess glue. The end was smooth and the bit of brass gave the pipe a touch of bling that was perfect. I took photos of the newly fitted band and have included them below. With the band in place on the shank I fit the stem in the shank and took photos of the new look. I still needed to polish the new stem but I wanted to give a sense of the whole with the photos. Have a look. I took a close up photo of the rim top and bowl along with the stem to show their general condition. The rim top looked good and the stem was in good condition as well without tooth marks or chatter on either side. I took a photo of the stamping on the underside of the shank. The JSP stamp is clear and readable.I set the stem aside and turned my attention to the bowl. I wiped the bowl down with isopropyl alcohol on a cotton pad to make the stain a bit more transparent so the grain showed through. I polished the bowl and shank with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I wiped down the bowl after each pad with a damp cloth to remove the sanding debris. I used a Mahogany stain pen to touch up the rim top to match the rest of the bowl. The rim matches the colour in the rest of the bowl and shank perfectly.I worked some Before & After Restoration Balm into the surface of the bowl and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and worked on the stem. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished polishing the stem with Before & After Pipe Stem Polish – both Fine and Extra Fine. I wiped the stem down with a final coat of Obsidian Oil and let it sit and absorb into the vulcanite.I am excited to finish this JSP “Joel Shapiro” Briar Stack with Vulcanite taper Stem. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with beautiful mixed grain all around it. Added to that the polished black vulcanite stem combined with the bowl made a stunning pipe. This smooth JSP Joel Shapiro Stack is great looking with its new stem and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ½ inches, Height: 2 ½ inches, Outside diameter of the bowl: 1 1/8 inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 39 grams/1.38 ounces. It is a beautiful pipe that I will soon be putting on the rebornpipes store in the American (US)Pipe Makers Section. If you are interested in adding it to your collection send me an email or a message. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.