Tag Archives: removing tooth marks

Restoring a Compact Straight Grain Freehand Saddle Stemmed Pipe

by Steve Laug

When Jeff and I were contacted about an estate in Santa Cruz, California, USA for sale I was excited to see what was in the lot. There were several with no other stamping on the shank than JHW. I have to say that I have seen very few JHW pipes and my heart skipped a beat when I saw not just one but 7 pipes with that stamping. All were Freehands and all were very unique – maybe even odd you might say! We purchased the estate on 05/28/2024. I am working on the second of the pipes. Now you might ask who is JHW? Why so excited about three initials? Well I have to tell you right up front that JHW is Jack H. Weinberger. Who is that? That does not help either? Jack H. Weinberger was a pipe maker in West Caldwell, New Jersey. Still not helping? He hired young lads from the local high school to help him out as he carved 10-12 hours a day. Two of these are none other than Curt Rollar and Mark Tinsky went on to become the American Pipe Company. There was a long list of pipe carving luminaries who came through Jack’s shop and JHW pipes but these two you probably have heard of. So JHW or Jack H. Weinberger was an important part of the American Pipemaking scene and gave many carvers a start and they have continued to this day. Now maybe you understand my excitement – being able to work on a few of Jack’s pipes and bring them back to their former glory.

This pipe I chose to work on was another unusual one. It is a great piece of plateau briar with straight grain all the way around the bowl and shank culminating in a tight pattern on the heel of the bowl. It is a beautiful piece of briar! But Jack chose to use this block very differently than most would have used a straight grain, plateau block. He made a very compact almost Opera style pipe but with a round bowl. The bowl is deep like a stack and seems conical as it moves toward the bottom. The plateau on the top side of the pipe has been brushed and flattened to knock off the rough edges. Very unusual but something just calls out to you. When the pipe came to us it was dirty with grime ground into the finish of the bowl. There was a thick cake in the bowl and lava on the rim top in the plateau. The stem is a thin bladed saddle that had light tooth marks and chatter on both sides just ahead of the button. There appeared to be some darkening around the inner edge of the rim and on the top itself. It was dirty but that did not hide the beauty of the briar. Jeff took photos of the pipe as a whole before he started his cleanup work. I include them below. Jeff took some close up shots of the rim top to show the bowl and cake. You can see the lava on the plateau rim top and the inner edge. The stem photos also show the condition it was in when we received it. Lots of promise with the pipe but some work too! Jeff took some photos of the sides – top, bottom, left and right to give a sense of the lay of the pipe on the block of briar. It is certainly unusual and unique. Here are some photos of the stamping on the underside of the shank. The J is a stylized pipe followed by uppercase HW. There is also the number 6 at the stem shank junction. It is clear and readable.Take some time to read the great writeup on Pipedia and JHW pipes and influence they had on the American pipe making scene. It is a well written and enjoyable read. Here is the link: (https://pipedia.org/wiki/JHW_Pipes). Interestingly there was a pipe pictured on the site that is the same shape as the one I am working on. I am including it for comparison sake.Armed with that information I turned to work on the pipe itself. Jeff had cleaned up the pipe with his usual thoroughness. He reamed the pipe with a PipNet pipe reamer and removed the rest of it with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners and shank brushes. He soaked the stem in Briarville’s Pipe Stem Deoxidizer and rinsed it off with warm water. I took photos of the pipe before I started my part of the restoration work. The plateau rim top cleaned up really well. The rim top and inner edge of the bowl look good. The bowl itself was very clean and the pipe smelled fresh. The stem surface had small tooth marks and chatter on both sides near the button. The stamping on the underside of the shank is clear and readable. It is stamped as noted above. I removed the stem and took a photo of the pipe to give a sense of the whole. I polished the briar with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped the bowl down with a damp cloth after each pad. By the end of the process it looked quite good. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips. I worked it into the plateau finish with a shoe brush. It works to clean, enliven and protect the briar. I let the balm sit for 15 minutes and buffed with a cotton cloth to raise the shine. The grain came alive. I set the bowl aside and turned my attention to the stem. I sanded out the tooth marks and chatter with 220 grit sandpaper until it was smooth.I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. I rubbed it down with a final coat of Obsidian Oil and let it dry. This Jack H. Weinberger (JHW) Straight Grain Compact Freehand Saddle Stem is a great looking pipe now that it has been restored. The beautiful grain around the bowl is quite stunning and works well with both the shape and the polished vulcanite taper stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the wheel and followed by buffing the pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Jack H. Weinberger (JHW) Compact Freehand fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 inches, Height: 2 inches, Outside diameter of the bowl: 1 3/8 inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 42 grams/1.48 ounces. I will be putting it on the rebornpipes store in the American Pipemakers Section shortly. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. I appreciate your support and time!

A Beautiful Preben Holm Surprise

Leave a reply

by Kenneth Lieblich

It was my birthday a couple of weeks ago and, much to my surprise, my parents gave me pipes for my birthday! I say “surprise” because my lovely folks were somewhat bemused when I got into the pipe-restoration hobby. However, this would seem to indicate that they have endorsed this great hobby of mine. This pipe is, by far, the nicest of the three I received. It is a Preben Holm 400 Free Hand. The grain is truly wonderful. Fortunately for me, the pipe was in decent condition when I got it. Not too much work required. Let’s have a look at the markings. On the underside of the shank, there are the words Preben Holm [over] Free-Hand [over] 400 [over] Hand Made [over] in [over] Denmark. My mother is of Danish extraction, so perhaps that played a role in this pipe’s selection. Over on the top of the stem, we see a crown above the letters PH (obviously standing for the man himself). In the past, I have often wondered about many Danish freehand shapes – especially Preben Holm’s. Sometimes (not always) they seem to be intricate merely for intricacy’s sake – or made to look like a piece of abstract art. However, Preben Holm is a true master of the craft and I don’t feel that sense of unnecessary complexity with this specific pipe. It is genuinely well made and beautiful. Let’s learn a bit more about Preben Holm and his pipes. Pipedia’s article about him says:

Preben Holm (1947-1989) has set some marks in pipe history. Just before his 16th birthday in 1963 he sold pipes to the legendary Pipe-Dan shop and at the age of only 22 he headed 45 employees. He was among the first Danish artisans who made “Danish pipe design” famous in the USA in the 1960’s. More than that he was one of the very first carvers who exceeded this moderate Danish Design which based on the classical shapes. “Chasing the grain” they turned out wild and dramatic fancy pipes. Combining smooth with blasted surfaces, showing big areas of the original bark at the top of the bowl and at the end of the stem, these pipes were quite shocking to many elder and more conservative pipe smokers. When he started to sell his pipes to Lane Ltd. under the Ben Wade label, he caused a hype fairly beyond comparison. Especially in the U.S., as most of his pipes were sold there.The Pipedia article also goes on to provide the very interesting tale of his business written by the man himself. I recommend reading it, although it deftly sidesteps discussing his own inner demons. In the same article, Poul Winslow says about Preben Holm:

Preben was a genius. Maybe a bit wild, always flying from idea to idea and impatient for results. But could he turn a pipe! Some of the most extreme free-hands came out of our workshop in the ’70s, and whatever his critics say, they sold like crazy, mostly in America. And when it came to finishing, he was the best in the business.There are a number of forums and websites that talk about his grading system. Unsurprisingly, much of this information is muddled, contradictory, or applicable to the Ben Wade pipes he made. From what I can understand – and I am happily corrected by those who know more – the era of pipes from which my pipe came used a grading system (ascending) of 100 to 500. Regardless of the accuracy of that information, my pipe is a 400.

Holm had a line of pipes called “Crown”, which, fittingly, had a crown on the stem – just like mine. However, all the examples of Crown pipes I’ve seen state that word on the pipe and that word isn’t on my pipe. The other point of mild frustration is that I seemingly have no way of dating this pipe, other than the unhelpfully and nebulously statement that it was made “in the ‘70s”. In 2020, Steve wrote an article about a PH Crown that he restored. It is not the same as mine and doesn’t have the same markings, but there is some indication that this pipe might have been distributed in the US by Lane Ltd under Preben Holm’s own name. Moving on…

I began work on the stem. Nothing especially remarkable here, but I needed to pay attention to the crown logo and PH because they were not as distinct as one would wish. I wiped down the outside of the stem with oil soap on some cotton pads. I also took a BIC lighter and ‘painted’ the stem with its flame in order to lift the little bit of tooth chatter. This helped a bit. Then, I cleaned out the insides of the stem with pipe cleaners and isopropyl alcohol. Once this process was done, I used some cleanser and cotton pads to wipe down the stem. I covered the logo with a dab of petroleum jelly before throwing it in the Pipe Stem Oxidation Remover overnight. The following day, I cleaned all of the de-oxidizing mess and used a toothbrush to remove the leftover oxidation. This worked well.I then used all nine Micromesh pads (1,500 through 12,000 grit) to bring out the lovely black lustre on the stem. I also used Obsidian Pipe Stem Oil in between each pad scrubbing.On to the stummel, and whoever previously had this pipe had done a decent job of cleaning the inside of the bowl. It didn’t need reaming, but I did use my pipe knife and some sandpaper to remove any cake. I took the bowl down to bare briar, as I wanted to ensure there were no hidden flaws in the walls of the bowl. Fortunately, there were none.Another important step in this process was removing the dirty remnants on the rim (as you’ve seen in the photos). I took a piece of machine steel and gently scraped away at this debris until it was gone. I love this technique because it is incredibly effective (more so than soaking) and does no damage whatsoever to the briar. The results speak for themselves.I then proceeded to clean out the insides of the shank with cotton swabs, pipe cleaners, and isopropyl alcohol. There was some filth inside this stummel, but it wasn’t too bad. I then moved on to cleaning the outside of the stummel with oil soap and some cotton pads. That removed any latent dirt. I followed that up by cleaning the insides with some soap and tube brushes. I noticed some very minor dents in the wood (see the photos) and I felt confident that those could be raised. I took an iron and a damp cotton cloth and steamed them. The hot, moist steam can often cause those sorts of injuries to swell back into shape. In this case, it worked a treat! I sanded down the stummel with my some of my micromesh pads to make it smooth and lovely. You will have noticed that there were two small nicks on the end of the shank. I deliberately decided to not fill these in. Instead, I simply sanded them thoroughly as I just described. This was a good decision as the nicks were minimized and are part of the pipe’s history. Of course, I added some restoration balm to the wood and let it sit for 20 minutes or so. I then buffed it with a microfibre cloth and – boy – did it look good! This balm does beautiful things to the wood and really generates a beautiful shine. I then took the pipe to my bench polisher and buffed it with White Diamond and a few coats of carnauba wax. All finished! This is a wonderfully crafted pipe and it really looks lovely. As it is a gift from my parents, this is one pipe that I am keeping for myself and adding to my collection. I am sure that I will be enjoying this one for many years to come. The approximate dimensions of the pipe are as follows: length 6½ in. (165 mm); height 2¼ in. (57 mm); bowl diameter 1¾ in. (46 mm); chamber diameter ⅞ in. (22 mm). The weight of the pipe is 1⅞ oz. (55 g). I hope you enjoyed reading the story of this pipe as much I as I did restoring it. If you are interested in more of my work, please follow me here on Steve’s website or email me directly at kenneth@knightsofthepipe.com. Thank you very much for reading and, as always, I welcome and encourage your comments.

Turning a Plateau Freehand on its side with JHW

Leave a reply

by Steve Laug

When Jeff and I were contacted about an estate in Santa Cruz, California, USA for sale I was excited to see what was in the lot. There were some great Freehand pipes by known carvers. There were also several with no other stamping on the shank than JHW. I have to say that I have seen very few JHW pipes in my years of working on pipes and my heart skipped a beat when I saw not just one but 7 JHW pipes. All were Freehands and all were very unique – maybe even odd you might say! We purchased the estate on 05/28/2024. I am finally getting around to working on the first of the pipes. Now you might ask who is JHW? Why so excited about three initials? Well I have to tell you right up front that JHW is Jack H. Weinberger. Who is that? That does not help either? Jack H. Weinberger was a pipe maker in West Caldwell, New Jersey. Still not helping? He hired young lads from the local high school to help him out as he carved 10-12 hours a day. Two of these are none other than Curt Rollar and Mark Tinsky went on to become the American Pipe Company. There was a long list of pipe carving luminaries who came through Jack’s shop and JHW pipes but these two you probably have heard of. So JHW or Jack H. Weinberger was an important part of the American Pipemaking scene and gave many carvers a start and they have continued to this day. Now maybe you understand my excitement – being able to work on a few of Jack’s pipes and bring them back to their former glory.

This first pipe I chose to work on was an unusual one. It is a great piece of plateau briar with straight grain all the way around the bowl and shank. It is a beautiful piece of briar! But Jack chose to use this block very differently than most would have used a straight grain, plateau block. He turned the pipe on its side. The bowl is on what most would have said was the right side. The plateau is on the left side of the pipe and a flat panel is on the right side. The photos show what I mean about the geography of the pipe. Very unusual but something just calls out to you. When the pipe came to us it was dirty. There was a thick cake in the bowl and lava on the rim top. The plateau was dirty with dust and debris and the finish dirty as well. The stem was a variegated brown acrylic saddle that had tooth marks and chatter on both sides just ahead of the button. There appeared to be some darkening on the left side of the inner edge of the rim and on the top itself. It was dirty but that did not hide the beauty of the briar. Jeff took photos of the pipe as a whole before he started his cleanup work. I include them below.Jeff took some close up shots of the rim top to show the bowl and cake. You can see the lava on the rim top and the nicks and scratches in the finish it is dirty and it is neglected. The stem photos also show the condition it was in when we received it. Lots of promise with the pipe but some work too! Jeff took some photos of the sides – top, bottom, left and right to give a sense of the lay of the pipe on the block of briar. It is certainly unusual and unique. Here is a photo of the stamping on the left side of the shank. The J is a stylized pipe followed by uppercase HW. It is clear and readable.Take some time to read the great writeup on Pipedia and JHW pipes and influence they had on the American pipe making scene. It is a well written and enjoyable read. Here is the link: (https://pipedia.org/wiki/JHW_Pipes).

Armed with that information I turned to work on the pipe itself. Jeff had cleaned up the pipe with his usual thoroughness. He reamed the pipe with a PipNet pipe reamer and removed the rest of it with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners and shank brushes. He soaked the stem in Briarville’s Pipe Stem Deoxidizer and rinsed it off with warm water. I took photos of the pipe before I started my part of the restoration work. The rim top cleaned up really well. The rim top and inner edge of the bowl look good. There was some darkening on the inner edge and a dark spot on the left side toward the back of the bowl. There were light scratches in the finish around the bowl. The stem surface had small tooth marks and chatter on both sides near the button. The stamping on shank sides is clear and readable. It is stamped as noted above. I removed the stem and took a photo of the pipe to give a sense of the whole.I cleaned up the inner edge of the bowl with a folded piece of 220 grit sandpaper to smooth out the damage and to clean up the darkening on the back of the rim top. Once finished it looks much better even with the damage and the darkening on the edge.I polished the briar with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped the bowl down with a damp cloth after each pad. By the end of the process it looked quite good. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips. I worked it into the plateau finish with a shoe brush. It works to clean, enliven and protect the briar. I let the balm sit for 15 minutes and buffed with a cotton cloth to raise the shine. The grain came alive. I set the bowl aside and turned my attention to the stem. I sanded out the tooth marks and chatter with 220 grit sandpaper until it was smooth.I polished the stem with 320-3500 grit sanding pads. I wiped the stem down after each sanding pad with an Obsidian Oil impregnated cloth. It removes the dust and also gives the sanding pads some bite. By the final pad it was looking quite good.I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. I rubbed it down with a final coat of Obsidian Oil and let it dry. This rare and unique Jack H. Weinberger Sideways Volcano is a great looking pipe. The beautiful grain around the bowl is quite stunning and works well with both the shape and the polished vulcanite taper stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the wheel and followed by buffing the pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Jack H. Weinberger (JHW) fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 ½ inches, Height: 2 inches, Outside diameter of the bowl: 2 ½ inches x 2 inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 113 grams/3.95 ounces. I will be putting it on the rebornpipes store in the American Pipemakers Section shortly. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. I appreciate your support and time!

Cleaning up a Chuck Whitmore Whidbey Islander Twisted Shank Dublin

Leave a reply

by Steve Laug

About a year ago I visited an older pipe repair man (when I say older I mean older than me). He gave me a lot of pipe parts – stems, bases, bowl, tenons and bands On Monday, August 25 after a visit with my brother Kenneth and I went to visit my contact again. This time he had more stuff that he wanted to get rid of from his parts. Once again, we received more stems and tenons. But he also put in a box of pipes that were in various states of repair or disrepair. One of those pipes was an interesting smooth Dublin with a twisted shank going into a diamond shaped saddle stem. The stamping, or rather etching on the left side of the shank is clear and readable. It reads Whidbey Islander. On the right side of the shank it read Made for Dick Dye. The bowl is an squat Dublin with a worm trail carving on the left side from the top and another on the right underside. The shank twists from the bowl junction back to the stem. It continues onto the saddle portion of the stem. It has some stunning grain around the bowl and shank even in its unpolished condition. The bowl had been reamed recently and the top and edges of the rim had some scratches. The inner edge was slightly out of round. The freehand vulcanite stem is square at the shank end then has a twist that continues from shank. It was oxidized and had some calcification ahead of the button on both sides. The stem had a repair in it mid stem – like it had been broken and repaired. There were tooth marks on the surface that had also been repaired with what looked like a white epoxy like substance. I took some photos of the pipe before I started my work. I took close up photos of the bowl and the stem. You can see the light cake in the bowl and the darkening on the rim top and the edges. There were also some scratches on the top. The stem surface was oxidized and had some calcification on the end ahead of the button. There were tooth marks and chatter on both sides on and ahead of the button. There were also two large repairs ahead of the button. They not black rather white. The stem also had been repaired at a crack in the middle across the stem.The next photos show the stamping that I described in the opening paragraph. It is clear and readable. I took a photo of the pipe with stem removed to give a sense of the proportions of the pipe. On the right side of the shank it read Made for Dick Dye. I wanted to have some idea who Dick Dye was. I googled the name and specified the Seattle area. I came up with an interesting and possible connection to a Richard Dye who passed away in 2019. The connection is pretty likely as he lived in the Seattle/Everett area of Washington state. Give the obit a read as it gives a bit of character of the man and his life (https://www.legacy.com/us/obituaries/heraldnet/name/richard-dye-obituary?id=14190787).

Before working on the pipe, I wanted to see what I could learn about the brand. I have a memory of visiting the shop many years ago but it is foggy so I did a bit of reading. There is a listing on Pipedia for Whidbey Islander Pipes (https://pipedia.org/wiki/Whidbey_Islander_Pipes). I quote the information from that site below. It is brief but quite interesting to read. I quote it in full.

Whidbey Islander Pipes are high-praised, but very rarely seen freehand pipes. Hand-cut Briars by Master Pipe Maker Travers LaRue were made and sold in his shop “Virginia Tobacco and Pipe Shoppe” in Langley on Whidbey Island, Washington between 1972-1983. LaRue died in 1983. He used 125 year old Sardinian briar and 150 year old Grecian Plateau briar with or without burl top. Trav custom designed ”free-hands” or classic shapes. A sterling dot on the shank along with his signature marked his one of a kind designs and possibly one of the best smoking pipes around. Trav taught his son-in-law Charles Whitmore the trade and soon he became a pipe maker too. The shop produced a hand-cut from 75 year old Italian briar known as the “Whidbey Islander”. These were mostly made by Chuck Whitmore that could be ordered with your own name inscribed. The shop was also known for hand blended pipe tobacco that was 100% pure premium quality American and imported tobaccos. The most famous being “Brown Crock”. The 1936 Hollywood Pipe Shop recipe that Bing Crosby smoked exclusively and loved by many. The family still owns the recipe. Travers pipes are few and precious. You’re lucky if you own one.

Judging from the description above I believe that I am working on a pipe made on Whidbey Island, Washington made by Chuck Whitmore between 1972-1983. It is a very interesting hand cut “twist” on a classic shaped pipe with great grain and a fancy vulcanite stem. Now it was time to work on the pipe.

I decided to address the damage to the inner edge of the bowl first. I used a folded piece of 220 grit sandpaper to give the inner edge of the bowl a slight bevel on the inner edge to remove burned areas and blend them into the surrounding briar. It began to really look better.I wiped off the varnish on the bowl with acetone on a cotton pad. I was careful around the signatures and stamping on the shank side. They were almost hand etched on the twisted shank sides. I was able to remove a lot of varnish and when done it looked much better. I needed to adjust the fit of the twisted shank to the twist in the stem. Nothing aligned in terms of either the sharp angles or the flattened portions. I used a folded piece of 220 grit sandpaper to correct the angles and flow of the twists on both the briar and the vulcanite. It was a lot of sanding but the improvement the look of the pipe was worth it. I smoothed out the sanding on the shank and started polishing the bowl with 320-3500 grit sanding pads. I wiped the briar down after each pad with a damp cloth to remove the sanding debris. The finish began to look very good. I touched up the sanded portions of the shank end with an Oak stain pen and blended it into the surrounding briar. It looked very good and the match was perfect. I polished the briar with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiping it down after each pad with a damp cloth. The briar took on a rich shine. I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar with my fingertips. The product works to clean, enliven and preserve the briar. I let it sit for 10 minutes then I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm. Now it was time to deal with the issues of the stem – the resanded and shaped fit to the shank, the crack mid blade and the white fills in the top and underside ahead of the button. They were many and varied but the shape of the stem made a new stem more work than I was willing to do at the moment. I filled in the repaired areas on the top and underside ahead of the button with black CA glue. Thankfully the repairs were a little indented. I sanded the stem surface and the repairs with 220 grit sandpaper. I also worked on the mid stem repairs to blend them in a bit more. I sanded the stem further to begin the polishing using 320-3500 grit sanding pads. I wiped the stem down after each pad with an Obsidian Oil impregnated cloth that really helped the sanding and helped protect it from oxidation.I polished the stem with micromesh sanding pads – dry sanding it with 1500-12000 grit pads. I wiped the stem down with Obsidian Oil after each pad. I polished it with Before & After Pipe Polish – both Fine and Extra Fine and gave it a final coat Obsidian Oil and set it aside to dry. Overall the stem looked better. There were still some ghosts of oxidation on the twists. The repairs on the white repaired areas showed. I am excited to finish this Chuck Whitmore made Whidbey Islander Twisted Dublin. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with beautiful grain all around it. The two carved trails carry on the flow of the angles of the twists in the shank and stem. Added to that the black vulcanite stem was beautiful. This smooth Whidbey Islander is great looking and the pipe feels great in my hand. It is light and well balanced. I am sure that Dick enjoyed it when he first picked it up at the shop. Have a look at it with the photos below. The dimensions are Length: 6 inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 5/8 inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 38 grams/1.34 ounces. It is a beautiful pipe and one I will hold onto for the memory of the shop. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.

The worst of Five Peterson’s in for restoration that are in rough condition – a burned out bowl and damaged stem

6 Replies

by Steve Laug

Yesterday afternoon I was visited by a pipe man here in Vancouver named Sergey who had five Peterson’s pipes that he wanted me to work on. They are shown in the photo below. In the left column from top to bottom: Peterson’s of Dublin Kinsale XL17, Peterson’s of Dublin Filter 68, Peterson’s of Dublin Kinsale XL16 Rusticated Pipe. In the right column from top to bottom Peterson’s of Dublin Kinsale XL16 and the bottom pipe is a Peterson’s of Dublin Kinsale XL14. All five pipes were all thickly caked and had thick lava on the rim top. The cake is so thick that I could not put my little finger in the bowl it was so heavily caked. My guess was that the bottom of the bowl was lower than the entrance of the airway into the bowl. The Rusticated Kinsale XL17 also had a burn out in the front bottom of the bowl that would take a lot more time than just a simple clean up. I would know more about the condition of each of the bowls once I had reamed and cleaned them. Sergey was travelling soon and he chose at least two of them that he wanted to take with him on his trip so those would be first. I have finished four of the five pipes and he picked them up and was pleased with them. The fifth of these was in the worst condition. I left it until last and now it was time to work on it – a Peterson’s of Dublin Kinsale XL16. I was not sure I would finish but he would love to take it on his travels.
I took photos of the Peterson’s of Dublin XL16 before I started working on it. This was Sergey’s favourite pipe and his concern was that it had a hole in the bottom toward the front. The finish is very dirty with oils and dirt ground into the briar. The rim top is thickly covered with tarry lava overflowing from the heavy cake in the bowl. The cake was thick and heavy all the way to the bottom of the bowl. In the heal of the bowl there was a hole about the size of pencil lead and the bowl was quite a bit deeper than the entrance of the airway from the shank. The vulcanite stem is also very dirty. There was oxidation, calcification and the P-lip had been cut off on the end. There was no button edge and he would like to have that added on the bottom of the stem surface. There oxidation, calcification and also some light tooth damage on both sides ahead of the remaining button. The P stamp on the left side of the stem is a gold P that is damaged. I took closeup photos of the rim top and bowl to give a sense of the dirty condition of the pipe and the thickness of the cake and lava on the bowl top. The rim top and edges look to be damaged under the lava coat but the cleanup will reveal the facts. I also took photos of the stem to show the top and underside ahead of the button.I took photos of the stamping on the shank sides. It was faint but readable through the grime and debris. It read as noted in the above paragraphs. I also took the stem off the shank and took a photo of the look and proportion of the pipe. I took a photo of the burnout in the heel of the bowl. It was about the size of pencil lead on the outside but the inside of the bowl was more extensively damaged. This one would take some extra work to bring it back to life.I started my work on the pipe by reaming the thick cake in the bowl. I could not even assess fully the burnout damage until it was reamed and cleaned. I used a PipNet pipe reamer with the first cutting head to take back the cake. I followed that with the second and the third cutting head. I was able to remove all of the cake. The cake in the bottom third of the bowl was incredibly hard and took a repeated reaming of that portion. I used a Savinelli Fitsall Pipe Knife to scrape the remainder of the cake out of the bowl and clean up the bottom of the bowl. I sanded the bowl walls with 220 grit sandpaper wrapped around a piece of dowel. With the bowl cleaned out I was able to determine that the bowl bottom was significantly below the entrance of the airway. It was quite thin and the hole on outside was only the beginning of the issues. I would need to repair the burn through and then build up the bottom of the bowl to the entrance of the airway. It would be further protection for the repaired bottom of the bowl and help it from further burning out. The issues with the rim top and inner edge would also need to be addressed. I decided to open up the burned-out area and see how extensive it was and how deep it was into the briar surrounding pin hole. I started with a sharp blade and cleaned up the opening and took out the brittle pieces of briar around the hole. I opened the hole further with a large drill bit and smoothed out the edges of the hole to the point it was solid briar.I scrubbed the externals of the bowl and shank with undiluted Murphy’s Oil Soap and a tooth brush. I rinsed it with warm running water and repeated the scrubbing and rinsing process until the pipe was clean and looked better. I cut a piece of briar and shaped it with my Dremel and sanding drum to fit the hole. I gave the inner edge a bevel to fit the edges of the hole. I rounded the inside of the plug with the Dremel to follow the flow of the bowl bottom. It would help build up the bottom significantly. I fit the plug in place on the bowl bottom and took some photos to give a sense of the look. Once it is glued in place and cured I will rusticate the patch to match the rest of the bowl.I mixed up a batch of two part JB Weld and coated the inner edge of the drilled out hole in the bowl bottom. I inserted the plug in the hole and used a tooth pick to fill in the gaps around the plug on the exterior of the bowl. I used a dental spatula to fill in the edges around the inside of the bowl and pressed it in place with a folded pipe cleaner. I built up the bowl bottom to the bottom of the airway entrance. I set it aside for the night to harden and cure. In the morning when I got up I shaped the plug with my Dremel and sanding drum to follow the flow of the bowl bottom. I clean up the edges of the plug and the surrounding briar with a folded piece of 220 grit sandpaper. It was looking pretty good at this point. I used a piece of dowel with 220 grit sandpaper wrapped around it to smooth out the bowl walls. I used some clear CA glue and some briar dust to fill in low spots around the front of the plug. I cleaned it up once it dried with a brass bristle wire brush to clean up the repair area. I sanded the edges of area with a folded piece of 220 grit sandpaper. It was a solid, smooth finish. All that remained was for me to rusticated it to match the surrounding briar.

I rusticated the repaired area with a Dremel and a series of burrs to match the rustication to the surrounding briar. I failed to take a photo of the bowl before I stained it. However, I used an Oak and a Mahogany stain pen to approximate the colour of the briar surrounding the repair. I took a photo of the various burrs I used with the Dremel to achieve the rustication patter that matches the rest of the bowl. I used a 3500 grit sanding pad to knock off the colour on the high points and give it a sense of depth. I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar with my fingertips to work it into the finish. The product works to clean, enliven and preserve the briar. I let it sit for 10 minutes then I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm. I mixed a bowl coating of sour cream and charcoal powder and painted the walls and bottom of the bowl to protect it during the break in period. I applied it to the walls and heel of the bowl with a folded pipe cleaner. I set it aside to let it cure. It would take about 24 hours for it to cure. I set the bowl aside and turned my attention to the stem. The stem was in as much of a mess as the bowl. The P-lip had been cut off and the underside of the stem was flat at an angle toward the opening of the airway in the end. The top of the P was missing other a thin ridge to approximate a button. It was roughly done and did not leave much to work with. I looked through my Peterson stems for a replacement but the tenon was odd sized and it was made for a 5MM filter so I had nothing. That left me with a decision. I decided to shape the stem end and build a fishtail button on the end. I would have to build up the button edges on both sides and I would need to try to cut a slot instead of just an odd shaped hole. With that in mind I had my hands full on this stem.

I rebuilt the button end on the top and bottom with rubberized black CA glue. I layered it in place after each layer cured. It took time to build up the layers and reshape it with files and sandpaper, but I like the new look much better. Once the button was solidly in place and the shaping was finished on it I still needed to clean up the shape and smooth it out and give it more of a sense of flow. I sharpened the edge on the top and underside of the button. I used several needle files to smooth out the edge and top. I smoothed out the top surface of the button on each side and on the end with a piece of 220 grit sandpaper. I used a series of round and oval needle files to shape the slot in the stem end. I took it for an out of round airway exit to an oval. I also used a slot cutting tool to continue to reshape the slot. I used a folded piece of 220 grit sandpaper to smooth out the inside of the slot. Once finished the slot looked much better. I polished the stem and the button with 320-3500 grit sanding pads. I wiped it down with a cloth impregnated with Obsidian Oil after each sanding pad to protect and polish the stem surface.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit pads. Once again I wiped it down between each pad with Obsidian Oil. I further polished it with Before and After Stem Polish – both Fine and Extra Fine. It looked very good. This Rusticated Peterson’s of Dublin Kinsale XL16 Bent Billiard with a Taper Stem has a beautiful rusticated finish that has a new lease on life. I repaired the burnout in the heel of the bowl by fitting it with a briar plug and then rusticating it to match the rest of the bowl. The medium brown/black/mahogany finish gives depth to the rustication around the bowl and shank. It has a classic look of a Peterson’s pipe. The rebuilt and polished black vulcanite taper stem adds to the mix. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel being careful to not buff the stamping. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Peterson’s of Dublin Kinsale XL16 Rusticated Bent Billiard is quite nice and feels great in the hand. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inch, Chamber diameter: 7/8 of an inch. The weight of the pipe is 2.68 ounces/78 grams. Thanks for walking through the restoration with me as I worked over another beautiful pipe. Sergey picked up the other four pipes on Monday. He pressed to pick this one up on Friday evening. I did not promise but I know it is his favourite pipe so it is ready for him.

Restemming and Restoring an Astley’s Sandblast Cherrywood

Leave a reply

by Steve Laug

Not too long ago I received and email from Nick, a fellow up the coast of British Columbia. He was not too far away and had gotten my information from City Cigar, a pipe and cigar shop that I do a lot of repairs for. He wrote the following email about two pipes he want me to restem for him.

Dear Steve,

I have a couple of pipes in need of new stems. City cigar suggested you might be able to help.

One is a diplomat, the other a cherrywood. Are you able to make new ones if I get the bowls to you?

I asked him to send me some photos of the pipe so I could see what he had and what I would be working with. I have a pretty good idea of the stems that I have and could tell him quite quickly once I saw the pipe if it was something I could work on.

He wrote back and sent me another brief email and included two photos of his pipes. This email made me think twice about the pipe because of what he wrote.

In trying to pull the tenon in the silver collared pipe, the diplomat I broke off a brass screw. It will need drilling I think. Best NickThe pipes arrived this week and I was surprised to find that they were both Astley’s pipes. I chose to work on the Cherrywood first. It had a lovely sandblast finish what was dirty and was stamped on a smooth panel on the underside of the shank. It read Astley’s [over] 109 Jermyn St. [over] London. The stamping was clear and readable. The bowl of the pipe had a moderate cake with some dust and debris in the sandblast of the rim top. The inner and outer edges of the bowl looked good. The pipe was missing the stem but Nick had sent along the snapped tenon in the bag with the pipes. I took photos of the stem to get a sense of what it looked like before I started my clean up. I took a photo of the rim top to capture the condition of the bowl and rim top. I like to capture that condition before I started my work on the pipe. You can see the dust in the sandblast on the rim top and the cake in the bowl. It is a nice looking pipe.I took a photo of the stamping on the underside of the shank and it is much clearer than the photo shows. It reads as noted above. Interestingly there was no shape number on the shank so it was a bit of a mystery pipe.Before I started my work on the pipe I did a bit of reading. I knew that I had work on an Astley’s Cherrywood previously and done a blog on it. A quick search on the blog took me to it. Here is a link (https://rebornpipes.com/2014/09/27/breathing-new-life-into-an-astleys-48-cherrywood/). I quote a portion of the blog below on the pipe. I found that it was a pipe that had a similar shape and had a shape number. I am also including some photos of the pipe when I had finished the restoration. The finish was not a sandblast but a rustication pattern that was very tight. The shape was the same as the one I was working on. This pipe was stamped on the heel of the bowl rather than the shank but it was the same. What was good about it was that it showed me the kind of stem that was originally on the pipe. That would guide me in fitting a new stem.This bowl had been stamped on the smooth bottom and read Astleys over 109 Jermyn St. Under that was stamped London over 48. I looked up the shape in an old Astleys catalogue (page pictured below) and found the 48 was a Round Cherrywood Briar. The description stated that it was a copy of an old English Cherrywood with a flat base. The bend on the stem can also be seen in the photo below from the catalogue.I started my work on the pipe by reaming it with a PipNet reamer using the second cutting head to take the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife. I sanded the walls of the bowl with 220 grit sandpaper wrapped around a piece of dowel to smooth out the walls. There was no checking or burn marks on the bowl walls it looked very good. I used a brass bristle wire brush to clean out the debris in the sandblast finish on the rim top. It looked much better at this point.I cleaned out the inside of the pipe – airway into the shank, the mortise and shank walls with pipe cleaners, alcohol and cotton swabs. I worked on it until it was very clean.I scrubbed the exterior of the pipe with undiluted Murphy’s Oil Soap and a tooth brush. I rinsed it off with warm running water and dried it off with a soft towel. The bowl looked good. The rim top had some fading that I would need to restain. I restained the faded rim top with a Mahogany stain pen to match the rest of the bowl and shank. The match to the rest of the bowl is quite perfect and it really makes the grain pop in the sandblast.I worked some Before & After Restoration Balm into the surface of the briar with my fingertips and a shoe brush to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The following photos show the bowl at this point in the restoration process. I am very happy with the results. With the bowl completed it was time to pick out a stem to fit the shank of the pipe. I wanted it to be the same diameter as the shank and fit snug in the shank. I went through my stems and found one that looked a lot like the Astley’s stem on the Cherrywood in the photos above. It is a saddle stem with a thin blade. It is used but it should clean up very well.
I cleaned out the airway in the stem with pipe cleaners and alcohol. The internals cleaned up very well. I also cleaned up the externals at the same time.I created a slight step down on the end of the tenon to secure a snug fit in the shank. I started the process with files and finished the shape with a Dremel and a sanding drum. Once it was finished it looked very good. It was similar in shape to the tenon on the Heritage pipe. It was going to work very well.I filled in the tooth marks along the edge of the button with some rubberized black super glue. By this time the repairs on the stem had cured so I flattened them out with a folded piece of 220 grit sandpaper. I worked over the button edge. It was beginning to shape up well.I sanded the stem with 320-3500 grit sanding pads and wiped the stem down after each pad to remove the sanding debris. It began to take on a deep shine.I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. I wiped it down with a final coat of Obsidian Oil and set it aside. The sandblast Astley’s 109 Jermyn St. London Cherrywood is a real beauty and the finish and shape are well done and have a classic English look. The newly fit vulcanite saddle stem polished up on the buffing wheel with Blue Diamond and had a rich glow. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Astley’s Cherry with a saddle stem fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.48 ounces/42 grams. I have one more pipe of Nick’s to restem and then I will be sending them back to him. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Restoring A Beautiful Heritage Embassy 44 Octagonal Pot

1 Reply

By Steve Laug

About a year ago I visited an older pipe repair man (when I say older I mean older than me). He gave me a lot of pipe parts – stems, bases, bowl, tenons and bands On Monday, August 25 after a visit with my brother Kenneth and I went to visit my contact again. This time he had more stuff that he wanted to get rid of from his parts. Once again, we received more stems and tenons. But he also put in a box of pipes that were in various states of repair or disrepair. One of those pipes was an interesting Octagonal Pot, a Kaywoodie Heritage Pipe. I have always had an interest in the Kaywoodie Made Heritage Pipe line. I really like the way they are made – both in terms of workmanship and style. They really made some amazing looking pipes and I always try to pick them up when I can. The pipe had been reamed and cleaned and was in good condition. The finish was also quite clean. The bowl was a sandblast Pot with twin bands of smooth briar around the sides of the bowl. The stamping on the underside of the shank is clear and has the shape number 44 on the heal of the bowl. That is followed by Heritage [over] Embassy. The stem was lightly oxidized and scratched from sitting in storage. It was also stuck solidly in the shank and would not turn no matter how hard I tried to turn it. I think that once I cleaned and polished the parts and put it back together it would be a great looking pipe. I took photos of the bowl and rim top to show the condition that I noted in the description above. It is quite clean and you can see that the rim top and edges all look very good. The stem photos clearly show the oxidation and light tooth marks on both sides. It will need some work.The next photos show the stamping that I described in the opening paragraph. It is clear and readable. I also included a photo of the double diamond logo on the left side of the taper stem. I took a photo of the pipe with stem removed to give a sense of the proportions of the pipe. In other blogs on the brand I have given a bit of history on the Heritage Brand. I have included that here as well for ease of reference. Andrew Selkirk did a great job in researching and I am including a link to his work on the blog (https://rebornpipes.com/2014/12/23/refurbishing-a-heritage-heirloom/). I am including a brief summary of what he found in the next two short paragraphs to set the stage for the pipe on my work table.

Heritage pipes were Kaywoodie’s answer to Dunhill. According to one of their brochures, Heritage pipes were made from “briar burls seasoned and cured for up to 8 months,” with only “one briar bowl in over 300 selected to bear the Heritage name.” “Heritage stems are custom fitted with the finest hand finished Para Rubber stems. Mouthpieces are wafer thin and concave.”

The Heritage line began in the early 1960’s, with the trademark issued in 1964. The line was started at the request of Stephen Ogden, (who worked for Kaywoodie in 1962). Mr. Ogdon had previous experience working for Dunhill, either running the New York store or working for Dunhill North America. Mr. Ogden was made President of Heritage Pipes, Inc., Kaywoodie Tobacco Co.,Inc. and Kaywoodie Products Inc. as well as a Vice President of S.M. Frank & Co. Heritage Pipes were produced from 1964 until 1970 (Source kaywoodie.myfreeforum.org).

Andrew also included a copy of the Heritage brochure that I am also including below (Courtesy kaywoodiemyfreeforum). In going through the models displayed on the page there is not one for the 44.

As I read through the brochure I found a copy of the Embassy line on the third page. I drew a red box around it to easily identify it below. It reads:

Heritage… a name to remember in the world of smoking… made by the world’s largest manufacturer of fine pipes. Here are pipes, perfect in beauty and balance and so cool and mellow to smoke. Available in smooth Diplomat finish or rough, rugged Antique or Embassy finishes…

The box also encloses a photo of an Embassy finished Bulldog. It has the sandblast finish with twin smooth bands around the bowl and a smooth band around the end of the shank. The overall finish is the same as the one I am working on.The brochure has a great write up on the Heritage Antique Line. It reads Rustic Grain Stands out in Rugged Relief. It describes the line as follows:

This pipe is so bold looking, yet so light and smooth smoking. A special sandblasting process exposes a greater surface area on the bowl, giving a cooler, more satisfying smoke. Centuries-old Heritage Antique is strikingly masculine in appearance.

Added to this description is the specific finish that characterizes an Embassy line pipe as described above. Now it was time to restore the pipe itself.

The pipe seemed to be covered with a thick coat of varnish that filled in the sandblast portion and was peeling slightly on the smooth bands and smooth shank end. I wiped it down with a cotton pad soaked with acetone. I was able to remove the shiny coat in full. It looked much better now that the finish was flat. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips and a horsehair shoe brush to clean, enliven and protect it. I worked it into the four lines on either side of the two smooth bands the line around the shank end ahead of the smooth band. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The following photos show the bowl at this point in the restoration process. I am very happy with the results. I set the bowl aside and turned my attention to the stem. I sanded the light tooth marks, chatter and oxidation on the stem with 220 grit sandpaper to blend them in. I followed that up with Soft Scrub worked into the stem surface with cotton pads and removed a lot of oxidation. The stem looked much better after this process. I sanded the stem with 320-3500 grit sanding pads and wiped the stem down after each pad to remove the sanding debris. It began to take on a deep shine.I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. I wiped it down with a final coat of Obsidian Oil and set it aside. The sandblast Heritage Embassy 44 Octagonal Pot is a real beauty and the finish and shape are well done and have a classic English look even though this is an American Made pipe. The thin taper vulcanite stem polished up on the buffing wheel with Blue Diamond and had a rich glow. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Heritage Embassy 44 Octagonal Pot fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.16 ounces/33 grams. I will soon be adding it to the rebornpipes store in the American Pipe Maker Section. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Fourth of Five Peterson’s in for restoration that are in rough condition

Leave a reply

by Steve Laug

Yesterday afternoon I was visited by a pipe man here in Vancouver named Sergey who had five Peterson’s pipes that he wanted me to work on. They are shown in the photo below. In the left column from top to bottom: Peterson’s of Dublin Kinsale XL17, Peterson’s of Dublin Filter 68, Peterson’s of Dublin Kinsale XL16 Rusticated Pipe. In the right column from top to bottom Peterson’s of Dublin Kinsale XL16 and the bottom pipe is a Peterson’s of Dublin Kinsale XL14. All five pipes were all thickly caked and had thick lava on the rim top. The cake is so thick that I could not put my little finger in the bowl it was so heavily caked. My guess was that the bottom of the bowl was lower than the entrance of the airway into the bowl. The Rusticated Kinsale XL17 also had a burn out in the front bottom of the bowl that would take a lot more time than just a simple clean up. I would know more about the condition of each of the bowls once I had reamed and cleaned them. Sergey was travelling in two weeks and he chose at least two of them that he wanted to take with him on his trip so those would be first. My hope is to try to finish four of the five. The fourth of these that he wanted is the next one I chose to work on. It was the Peterson’s of Dublin Filter 68. I took photos of the Peterson’s of Dublin Filter 68 before I started working on it. This was Sergey’s first pipe and his concern was that it smoked hot. The finish is very dirty with oils and dirt ground into the briar. There is some spotty varnish on the finish that may well have contributed to the pipe smoking hot to the touch. The briar actually looks very good with great grain. The rim top is thickly covered with tarry lava overflowing from the heavy cake in the bowl. The cake was thick and heavy all the way to the bottom of the bowl. The vulcanite stem is also very dirty. There was oxidation, calcification and tooth marks and chatter on both sides of the stem ahead of the button and lip edge. The P stamp on the left side of the stem is a gold P that is faint and faded. I took closeup photos of the rim top and bowl to give a sense of the dirty condition of the pipe and the thickness of the cake and lava on the bowl top. The rim top and edges look to be ok under the lava coat as seen in the photos as well. I also took photos of the stem to show the top and underside ahead of the button.I took photos of the stamping on the shank sides. It was faint but readable through the grime and debris. It read as noted in the above paragraphs. I also took the stem off the shank and took a photo of the look and proportion of the pipe. I started my work on the pipe by reaming the thick cake in the bowl. I used a PipNet pipe reamer with the first cutting head to take back the cake. I followed that with the second and the third cutting head. I was able to remove all of the cake. The cake in the bottom third of the bowl was incredibly hard and took a repeated reaming of that portion. I used a Savinelli Fitsall Pipe Knife to scrape the remainder of the cake out of the bowl and clean up the bottom of the bowl. I sanded the bowl walls with 220 grit sandpaper wrapped around a piece of dowel. With the bowl cleaned out I was able to determine that the bowl bottom was in better condition than the first or second pipe. I would need to build up the bottom of the bowl slightly to the entrance of the airway. It would be further protection for the bottom of the bowl and help it from burning out. The issues with the rim top and inner edge would also need to be addressed. I scrubbed out the internals with 99% isopropyl alcohol, cotton swabs and pipe cleaners. I worked them through the airway in the shank and stem, the mortise. It took a few cleaners and swabs to really clean it but it is looking and smelling much better.I scrubbed the externals of the bowl and shank with undiluted Murphy’s Oil Soap and a tooth brush. I rinsed it with warm running water and repeated the scrubbing and rinsing process until the pipe was clean and looked better. I wiped down the bowl with acetone (fingernail polish remover) to remove the spotty varnish coat on the briar. The varnish may be contributing to the pipe smoking hot. At this point the briar began to look good. At this point I decided to address the rim top and edge damage. There burn damage to the inner edge and onto the rim top. I wanted the top to be smooth once again and also wanted to bring the bowl back to round. I started by topping the bowl with 220 grit sandpaper on a topping board to smooth out the damage on the rim surface and clean up the outer edge damage. I was able to significantly clean up the damage. The other pipes I have worked on for Sergey have all had a slightly bevelled inner edge so I would need to do that with this pipe as well. I used 220 grit sandpaper and a wooden sphere to give the inner edge a bevel. I used a wooden sphere and a piece of 220 grit sandpaper to work on the edge and give it a slight bevel. Once finished it looked much better. I used a Cherry stain pen to touch up the rim top to match the rest of the bowl. I did this before sanding the bowl as I would also sand the top at the same time. I think the match was going to be perfect. We would see.I sanded the bowl with 320-3500 grit sanding pads to remove some of the darkening around the bowl. I wiped it down after each sanding pad with a damp cloth to remove the sanding debris. It really began to look very good. I touched up the rim top once more with a Walnut Stain Pen. The colour matched surrounding stain on the briar. Polishing it would blend it very well.I polished the bowl with micromesh sanding pads – dry sanding with 1500-12000 grit pads. Each pad gave it more of a shine. I wiped the bowl down after each pad with a damp cloth. By the end the bowl looked very good. I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar with my fingertips to work it into the finish. The product works to clean, enliven and preserve the briar. I let it sit for 10 minutes then I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm. I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit pads. Once again I wiped it down between each pad with Obsidian Oil. I further polished it with Before and After Stem Polish – both Fine and Extra Fine. It looked very good. The P logo on the left side of the stem was so faint and damaged but I tried to touch it up with some Rub’n Buff Antique Gold. I worked it into the remaining stamp with a tooth pick. It worked better than I expected but it was not flawless. This Peterson’s of Dublin Filter 68 Bent Billiard with a Taper Stem has a beautiful smooth finish that was slightly worn. The medium brown finish highlights some great grain around the bowl and shank. It has a classic look of a Peterson’s pipe. The polished black vulcanite taper stem adds to the mix. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel being careful to not buff the stamping. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Peterson’s of Dublin Filter 68 is quite nice and feels great in the hand. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inch, Chamber diameter: ¾ of an inch. The weight of the pipe is 2.08 ounces/59 grams. Thanks for walking through the restoration with me as I worked over another beautiful pipe. I have one more pipe to finish but these four are ready to pick up and Sergey can take them on his travels. The last one I will give back when he returns. Thanks for your time.

Third of Five Peterson’s in for restoration that are in rough condition

Leave a reply

by Steve Laug

Yesterday afternoon I was visited by a pipe man here in Vancouver named Sergey who had five Peterson’s pipes that he wanted me to work on. They are shown in the photo below. In the left column from top to bottom: Peterson’s of Dublin Kinsale XL17, Peterson’s of Dublin Filter 68, Peterson’s of Dublin Kinsale XL16 Rusticated Pipe. In the right column from top to bottom Peterson’s of Dublin Kinsale XL16 and the bottom pipe is a Peterson’s of Dublin Kinsale XL14. All five pipes were all thickly caked and had thick lava on the rim top. The cake is so thick that I could not put my little finger in the bowl it was so heavily caked. My guess was that the bottom of the bowl was lower than the entrance of the airway into the bowl. The Rusticated Kinsale XL17 also had a burn out in the front bottom of the bowl that would take a lot more time than just a simple clean up. I would know more about the condition of each of the bowls once I had reamed and cleaned them. Sergey was travelling in two weeks and he chose at least two of them that he wanted to take with him on his trip so those would be first. My hope is to try to finish four of the five. The third of these that he wanted is the next one I chose to work on. It was the Peterson’s of Dublin Kinsale XL14.I took photos of the Peterson’s of Dublin Kinsale XL14 before I started working on it. The finish is very dirty with oils and dirt ground into the briar. There are some nicks and flaws around the bowl sides and at least one fill. The rim top is thickly covered with tarry lava overflowing from the heavy cake in the bowl. It had some burn damage on the front outer edge of the bowl and the bowl was very out of round on the inner edge. The cake was thick and heavy all the way to the bottom of the bowl. The vulcanite stem is also very dirty. There was oxidation, calcification and tooth marks and chatter on both sides of the stem ahead of the button and lip edge. The P stamp on the left side of the stem is a gold P that is faint and faded. It also has some damage on the surface around the P. I took closeup photos of the rim top and bowl to give a sense of the dirty condition of the pipe and the thickness of the cake and lava on the bowl top. The damage to the rim top and edges is very clear in the photos as well. I also took photos of the stem to show the top and underside ahead of the button.I took photos of the stamping on the shank sides. It was faint but readable through the grime and debris. It read as noted in the above paragraphs. I also took the stem off the shank and took a photo of the look and proportion of the pipe. I started my work on the pipe by reaming the thick cake in the bowl. I used a PipNet pipe reamer with the first cutting head to take back the cake. I followed that with the second and the third cutting head. I was able to remove all of the cake. The cake in the bottom third of the bowl was incredibly hard and took a repeated reaming of that portion. I used a Savinelli Fitsall Pipe Knife to scrape the remainder of the cake out of the bowl and clean up the bottom of the bowl. I sanded the bowl walls with 220 grit sandpaper wrapped around a piece of dowel. With the bowl cleaned out I was able to determine that the bowl bottom was in better condition than the first or second pipe. I would need to build up the bottom of the bowl slightly to the entrance of the airway. It would be further protection for the bottom of the bowl and help it from burning out. The issues with the rim top and inner edge would also need to be addressed. At this point I decided to address the rim top and edge damage. There was serious damage to the inner edge. The front of the rim top had been burned and had a slight dip in it. The outer edge in front of the burned rim top was also damaged. I wanted the top to be smooth once again and also wanted to bring the bowl back to round. I started by topping the bowl with 220 grit sandpaper on a topping board to smooth out the damage on the rim surface and clean up the outer edge damage. I was able to significantly clean up the damage. The Kinsales that I have worked on for Sergey have all had a slightly bevelled inner edge so I would need to do that with this pipe as well. It would also clean up the out of round bowl a bit more.I used a wooden sphere and a piece of 220 grit sandpaper to work on the edge and give it a slight bevel. Once finished it looked much better.I scrubbed out the internals with 99% isopropyl alcohol, cotton swabs and pipe cleaners. I worked them through the airway in the shank and stem, the mortise. It took a few cleaners and swabs to really clean it but it is looking and smelling much better.I scrubbed the externals of the bowl and shank with undiluted Murphy’s Oil Soap and a tooth brush. I rinsed it with warm running water and repeated the scrubbing and rinsing process until the pipe was clean and looked better. I used a Cherry stain pen to touch up the rim top to match the rest of the bowl. I did this before sanding the bowl as I would also sand the top at the same time. I think the match was going to be perfect. We would see.I sanded the bowl with 320-3500 grit sanding pads to remove some of the darkening around the bowl. I wiped it down after each sanding pad with a damp cloth to remove the sanding debris. It really began to look very good. I polished the bowl with micromesh sanding pads – dry sanding with 1500-12000 grit pads. Each pad gave it more of a shine. I wiped the bowl down after each pad with a damp cloth. By the end the bowl looked very good. Once I had I polished the bowl I addressed overly deep bowl bottom. I filled in the bottom with a mix of cigar ash and water to make a pipe mud. I pressed it into place with a tamper to flatten it. I put a pipe cleaner in the airway so that I would only fill it to the bottom of the pipe cleaner. I set it aside to dry and harden. It looks much better. It will take awhile to harden but it should deal with the damage. If it shrinks when it cures I will need to fill it in a bit more. At this point I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar with my fingertips to work it into the finish. The product works to clean, enliven and preserve the briar. I let it sit for 10 minutes then I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm. I set the bowl aside and turned my attention to the stem. I “painted” the tooth marks on both sides with the flame of a Bic lighter. I filled in the two deeper marks on the underside of the stem that remained with black rubberized CA glue and set it aside to cure. Once it had hardened I sanded the with 220 grit sandpaper and smoothed them out. The P logo on the left side of the stem was so faint and damaged but I tried to touch it up with some Rub’n Buff Antique Gold. I worked it into the remaining stamp with a tooth pick. It worked better than I expected but it was not flawless. I sanded the stem with 320-3500 grit sanding pads to take out the scratching and remaining oxidation. I wiped it down after each pad with some Obsidian Oil. It is looking much better now.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit pads. Once again I wiped it down between each pad with Obsidian Oil. I further polished it with Before and After Stem Polish – both Fine and Extra Fine. It looked very good. This Peterson’s of Dublin Kinsale X14 Rhodesian with a Taper Stem has a beautiful smooth finish that was slightly worn. The reddish brown finish highlights some great grain around the bowl and shank. It has a classic look of a Peterson’s pipe. The polished black vulcanite taper stem adds to the mix. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel being careful to not buff the stamping. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Peterson’s of Dublin Kinsale XL14 is quite nice and feels great in the hand. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inch, Chamber diameter: 7/8 of an inch. The weight of the pipe is 2.36 ounces/67 grams. Thanks for walking through the restoration with me as I worked over another beautiful pipe. I have two more pipes to finish but these three are ready to pick up and Sergey can take them on his travels. The last two I will give back when he returns. Thanks for your time.

Second of Five Peterson’s in for restoration that are in rough condition

Leave a reply

By Steve Laug

Yesterday afternoon I was visited by a pipe man here in Vancouver named Sergey who had five Peterson’s pipes that he wanted me to work on. They are shown in the photo below. In the left column from top to bottom: Peterson’s of Dublin Kinsale XL17, Peterson’s of Dublin Filter 68, Peterson’s of Dublin Kinsale XL16 Rusticated Pipe. In the right column from top to bottom Peterson’s of Dublin Kinsale XL16 and the bottom pipe is a Peterson’s of Dublin Kinsale XL14. All five pipes were all thickly caked and had thick lava on the rim top. The cake is so thick that I could not put my little finger in the bowl it was so heavily caked. My guess was that the bottom of the bowl was lower than the entrance of the airway into the bowl. The Rusticated Kinsale XL17 also had a burn out in the front bottom of the bowl that would take a lot more time than just a simple clean up. I would know more about the condition of each of the bowls once I had reamed and cleaned them. Sergey was traveling in two weeks and he chose at least two of them that he wanted to take with him on his trip so those would be first. My hope is to try to finish four of the five. The second of these that he wanted is the next one I chose to work on. It was the Peterson’s of Dublin Kinsale XL17.I took photos of the Peterson’s of Dublin Kinsale XL17 before I started working on it. The finish is very dirty with oils and dirt ground into the briar. The rim top is thickly covered with tarry lava overflowing from the heavy cake in the bowl. The cake was thick and heavy all the way to the bottom of the bowl. The vulcanite stem is also very dirty. There was oxidation, calcification and tooth marks and chatter on both sides of the stem ahead of the button and lip edge. The P stamp on the left side of the stem is a gold P that is faint and faded. I took closeup photos of the rim top and bowl to give a sense of the dirty condition of the pipe and the thickness of the cake and lava on the bowl top. I also took photos of the stem to show the top and underside ahead of the button.I took photos of the stamping on the shank sides. It was faint but readable through the grime and debris. It read as noted in the above paragraphs. I also took the stem off the shank and took a photo of the look and proportion of the pipe. There is also some glue around the band that makes me think it has been reglued. I started my work on the pipe by reaming the thick cake in the bowl. I used a PipNet pipe reamer with the first cutting head to take back the cake. I followed that with the second and the third cutting head. I was able to remove all of the cake. The cake in the bottom third of the bowl was hard. I used a Savinelli Fitsall Pipe Knife to scrape the remainder of the cake out of the bowl and clean up the bottom of the bowl. I sanded the bowl walls with 220 grit sandpaper wrapped around a piece of dowel. With the bowl cleaned out I was able to determine that the bowl bottom was in better condition than the first pipe. I would build up the bottom of the bowl slightly to the entrance of the airway. It would protect the bottom from burning out. I scrubbed out the internals with 99% isopropyl alcohol, cotton swabs and pipe cleaners. I worked them through the airway in the shank and stem, the mortise. It took a few cleaners and swabs to really clean it but it is looking and smelling much better.I scrubbed the externals of the bowl and shank with undiluted Murphy’s Oil Soap and a tooth brush. I rinsed it with warm running water and repeated the scrubbing and rinsing process until the pipe was clean and looked better. I sanded the bowl with 320-3500 grit sanding pads to remove some of the darkening around the bowl. I wiped it down after each sanding pad with a damp cloth to remove the sanding debris. It really began to look very good. I polished the bowl with micromesh sanding pads – dry sanding with 1500-12000 grit pads. Each pad gave it more of a shine. I wiped the bowl down after each pad with a damp cloth. By the end the bowl looked very good. Once I had I polished the bowl I addressed overly deep bowl bottom. I filled in the bottom with a mix of cigar ash and water to make a pipe mud. I pressed it into place with a tamper to flatten it. I put a pipe cleaner in the airway so that I would only fill it to the bottom of the pipe cleaner. I set it aside to dry and harden. It looks much better. It will take awhile to harden but it should deal with the damage. If it shrinks when it cures I will need to fill it in a bit more.At this point I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar with my fingertips to work it into the finish. The product works to clean, enliven and preserve the briar. I let it sit for 10 minutes then I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm. I set the bowl aside and turned my attention to the stem. I “painted” the tooth marks on both sides with the flame of a Bic lighter. I filled in the two deeper marks with black rubberized CA glue and set it aside to cure. One it had hardened I sanded the with 220 grit sandpaper and smoothed them out. I touched up the P logo on the left side of the stem with Rub’n Buff Antique Gold. I worked it into the stamp on the stem with a tooth pick and worked it in. Once it had been sitting I rubbed it off with a cloth and polished the area with a 1500 grit micromesh sanding pad.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit pads. Once again I wiped it down between each pad with Obsidian Oil. I further polished it with Before and After Stem Polish – both Fine and Extra Fine. It looked very good. This Peterson’s of Dublin Kinsale X17 Bent Rhodesian with a Taper Stem has a beautiful smooth finish that was slightly worn. The reddish brown finish highlights some great grain around the bowl and shank. It has a classic look of a Peterson’s pipe. The polished black vulcanite taper stem adds to the mix. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel being careful to not buff the stamping. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Peterson’s of Dublin Kinsale XL17 is quite nice and feels great in the hand. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inch, Chamber diameter: 7/8 of an inch. The weight of the pipe is 2.75 ounces/78 grams. Thanks for walking through the restoration with me as I worked over another beautiful pipe. I have three more pipes to finish before I give them back to Sergey. Thanks for your time.