Tag Archives: polishing stems

A New Beginning For An Inherited Peterson’s # 3 System Pocket Pipe…

6 Replies

Blog by Paresh Deshpande

Over the last month and a half, I have worked on five Peterson’s pipes to be added to my personal collection; two from my inherited lot (DONEGAL ROCKY # 999 and KAPMEER # 120S) and three that I had purchased on eBay, a Peterson’s SYSTEM # 31 just so that I could include it in my rotation, a Peterson’s BARREL and a Peterson’s OLD ENGLISH COLLECTION. Continuing with my work on Peterson’s in my collection, the next and sixth pipe that is now on my work table is one from my inheritance; a unique small system pipe with oval shaped chamber/ stummel. The stem folds itself over the rim top, further making it compact enough in size to be carried in one’s vest pocket.

The smooth stummel of this pipe has a beautiful mix of Bird’s eye on the foot of the stummel and cross grain on the front, back, sides and the upturned shank of the stummel. An oval shaped stummel, short upturned shank with a nickel plated ferrule at the shank end and a proportionate vulcanite stem with an orifice for a slot, makes it a visually appealing pipe. It is stamped on the left side of the shank as “K & P” over “3”. The shank end is adorned with a nickel ferrule that is stamped in three shields as “K” “&” “P” over three faux hallmarks a Shamrock, a Prone Fox, and a Stone Tower. The stummel is devoid of any COM stamp that would help in dating this pipe. Even the stem is unstamped. Since I have been recently working on Peterson’s pipes in my collection and reading about it as much as I could, I knew that K & P pipes did not have any COM stamp during the early part of the Patent Era. Furthermore, this pipe has a reservoir/ sump in the mortise making it a System pipe!! The stem slot is a round orifice which points to this pipe being an old one. Thus from these facts, I can safely presume this pipe to be from the Patent Era, that is from 1875 to 1922.

However, in spite of my extensive research on Peterson’s pipes for shapes and models from this era, I came a cropper!!!! In case any of the esteemed readers has some additional information on this pipe, I would request you to share it on Reborn pipes for the benefit of our community.

Initial Visual Inspection
The smooth stummel on this pipe is covered in a thick layer of dust and sticky grime giving it a dull and lackluster appearance. Through all the grime, bird’s eye and cross grains can be still seen at the foot and on sides, front and back of the stummel respectively. The rim top surface appears uneven and is covered in dust, heavy lava overflow, grime and will need to be cleaned and polished. There are a few scratches on the left side of the stummel which will need to be addressed. A few fills seen on either side of the stummel need to be refreshed. The stummel has developed a nice patina which I shall endeavor to preserve. The chamber has a thick layer of uneven cake with lava overflow over the rim top surface. Remnants of half burnt tobacco can be seen at the bottom half of the stummel. The condition of the inner walls of the chamber will be ascertained once the existing cake has been taken down to the bare briar. The draught hole is completely blocked with absolutely no draw. This needs to be addressed. The thin and delicate rim edge appears to be severely damaged with dents and dings all around; however, the extent of this damage will be ascertained once the cake and lava overflow from the chamber and rim top is entirely removed. There is a very strong smell to the chamber which, perhaps, may reduce appreciably after the chamber has been cleaned. The mortise and sump are clogged with dried oils and tars. The nickel ferrule at the shank end, though heavily oxidized, is undamaged. It is cut at an angle to accommodate the stem when it is turned over the stummel. The ferrule, once cleaned should polish up nicely. The vulcanite stem is heavily and deeply oxidized with tooth indentations on the button edge and chatter on either surfaces of the stem in the bite zone. The tenon end shows heavy traces of dried oils and tars. It’s going to take some elbow grease to clean up this stem to a nice deep and shining black. The perpendicular tenon end will make the internal cleaning a bit challenging. The orific slot shows deposition of dried oils and tars. The stink from the stem and clogged airway will take a lot of effort and time to clean up. The Process
I began the process of refurbishing this pipe by using my fabricated knife to remove the unburnt tobacco and thick layer of cake. I further took the cake down to the bare briar with a folded piece of 150 grit sand paper. Once the walls of the chamber were rid of all the remnants of the cake, the chamber walls were found to be smooth and without any damage. With my modified and straightened cloth hanger used as a poker, I cleaned the grime and cake that covered the draught hole at the heel of the stummel. I further wiped the chamber with a cotton swab wetted with isopropyl alcohol to completely remove the sanding dust. While handling the stummel for internal cleaning of the chamber, the nickel ferrule came off, revealing a crack on the left side. This crack extends from the shank end rim surface (indicated with a yellow arrow) and along the shank on the left side (indicated with blue arrows). The extent of the crack will be determined once the dirt, grime and dried glue are removed from the surface. The edges of the ferrule are slightly uneven while the insides of it have traces of deeper oxidation.   I scraped the shank internals with a fabricated tool to remove all the crud that had accumulated along the shank walls and further cleaned it with bristled and regular pipe cleaners dipped in isopropyl alcohol. A huge pile of q-tips, pipe cleaners and lots of elbow grease later, the sump and mortise still appear dirty. I shall further draw out all the residual oils, tars and gunk by subjecting the chamber and the shank to a salt and alcohol bath. I gently scraped the shank end rim surface to remove all the accumulated oils and grime. Now that the shank end rim was cleaned, a second crack on the right side came to the fore (indicated in yellow arrows). This project is turning out to be more time consuming than I had anticipated. I shall deal with these cracks after I am done with internal and external cleaning of the stummel. I cleared the draught hole using a fabricated poker and further cleaned it using pipe cleaners and alcohol. I continued with the cleaning of the chamber and shank internals with a salt and alcohol bath. I use cotton balls which is an at par substitute to Kosher salt as I have realized over the years. I draw out a wick from the cotton and along with a folded regular pipe cleaner; insert it in to the mortise and through the draught hole into the chamber. Thereafter, I packed the chamber with cotton balls to about quarter of an inch below the rim’s inner edge and soaked the cotton balls with isopropyl alcohol up to the brim. About half an hour later, the level of alcohol had gone down, having being absorbed by the cotton. I topped it up once again and set it aside overnight. By the next afternoon, the cotton and alcohol had drawn out all the remaining oils and tars from the chamber and mortise, fulfilling its intended task. I removed the cotton balls and ran pipe cleaners through the mortise to clean out all the loosened tars and gunk. Using my fabricated tool, I scraped out the entire loosened gunk from the sump and further cleaned it with alcohol and q-tips. The chamber now smells clean and fresh. I set the stummel to dry out naturally. Now that the internals of the stummel were cleaned, I scrubbed the external surface of the bowl with undiluted Murphy’s oil soap and hard bristled tooth brush. I deliberately cleaned the thin delicate rim top and the surface just below the rim edge with Scotch Brite and a soft bristled brass wire brush to remove the entire lava overflow and dried it using paper towels and a soft cotton cloth. The shank end rim surface and the shank were deliberately cleaned to remove the grime and dirt so that the exact extent of the two cracks could be fathomed. The thin rim top is generously peppered with nicks, dings and dents. The fills and cracks that are visible on the stummel surface are marked in yellow circles and blue arrows respectively. I removed the old fills and prepared the stummel for a fresh fill. Using my dental tools, I progressed to removing the fills. I know these pictures do not present a very encouraging scenario at this stage, but I shall prevail… I wiped the surface from where the old fill was gouged out, with isopropyl alcohol to clean the area. I let the stummel dry out completely and after all the alcohol had evaporated, proceeded to fill the gouges with CA superglue and briar dust using the layering technique where I put down a thin layer of superglue in to the fill and press briar dust over the glue. I continue with this process till the fill rises above the rest of the stummel surface. Once all the gouges were filled up, I set the stummel aside to cure for the next 24 hours.While the stummel fills were curing, I worked the stem. The stem air way was filthy to say the least. Using a shank brush and dish washing soap, I cleaned the stem air way. I further cleaned the stem internals with hard and regular pipe cleaners and isopropyl alcohol. A lot of elbow grease and a pile of pipe cleaners later, the pipe cleaners did not emerge as white as I wanted. The perpendicular positioning of the tenon to the rest of the stem made cleaning of the air way all the more difficult. In my exuberance, I chipped the very end of the tenon… Some additional unwarranted work and time penalty!! With the stem internals now somewhat clean, I moved to external cleaning of the stem surface by sanding the surface with a piece of 220 grit sand paper and thereafter dunking the stem in to “Before and After Deoxidizer” solution developed by my friend Mark Hoover. The solution helps to draw out heavy oxidation to the surface making its further removal a breeze, while the minor oxidation is eliminated to a very great extent. I usually dunk stems of 5-7 pipes that are in-line for restoration and the K & P # 3 pipe is marked in pastel pink arrow. I generally allow the stems to soak in this solution overnight for the solution to do its work.Next day, I remove the stems from the deoxidizer solution and clean them under warm running tap water to remove all the solution. I scrubbed the stem surface first with scotch brite pad followed by a piece of 0000 grade steel wool. This helps in removing all the raised oxidation from the stem surface. I rubbed a little Extra Virgin Olive oil in to the stem and wiped the excess with a paper napkin. This was followed by inserting a petroleum jelly smeared folded pipe cleaner in to the tenon for reconstruction of the tenon end. Using a mix of CA superglue and food grade activated charcoal, I began the arduous process of rebuilding the chipped tenon end and also the bite marks on the button edges on both sides in the bite zone. I set the stem aside for the fill to cure and harden completely. I took a stock of the progress made till now on this pipe; stummel internals/ externals cleaned, old stummel fills have been refreshed and cured, stem internals cleaned, stem oxidation removed to a great extent, stem repairs set aside for curing. Addressing the stummel cracks, sanding of the stummel and stem fills, refurbishing the nickel band and final polishing is all that remains to be completed.

Next, I address the two cracks at the shank end. Using a magnifying glass and a white correction pen, I marked the points for the counter holes at the end points along the extent of the cracks seen on the stummel. I drilled counter holes with a 1mm drill bit mounted on to my hand held rotary tool, deep enough to serve as a counter hole while taking care that I did not drill a through and through hole. These counter holes arrest and prevent the spread of the cracks further. I filled these cracks and counter holes with a mix of briar dust and CA superglue using the layering method (layer of superglue followed by sprinkling of briar dust and repeated it till desired thickness of fill was achieved) and set it aside for the fills to cure. I ensured that I filled the thin outer edge of rim top surface that I will subsequently sand down to match with the rest of the rim surface. I set the stummel aside for the fills to harden. I cleaned the nickel shank band with Colgate Toothpowder, which Abha, my wife, uses to polish her silver and gold cutlery and jewelry. This compound is a very fine powder and is least abrasive with fantastic results. The band is now a nice shining piece of nickel and should provide a nice contrast to the shining black stem and the dark brown stummel. The patches of deep oxidation that were observed were also completely eliminated.  With the stummel fills nicely cured, it was time again to work on it. Using a flat head needle file, I sanded the fills and followed it by sanding with worn out folded piece of 150 grit sand paper. I sand the thin rim top surface with the same sand paper to minimize the numerous chips, dents and dings. I did not resort to topping since the oval shape with a slight saddle dip in the centre makes it difficult to top without compromising the shape of the rim top. A couple of dents and chips are still visible, but I shall let them be as a part of this pipe’s journey from my grandfather then to with me now!!! The fills have blended in quite well. However, I shall strive to further achieve a near perfect blend during further sanding and polishing with micromesh pads. The shank end crack repairs are now solid and have blended in really well. Yeah, I am pleased with this progress. Thereafter, I polished the entire stummel with micromesh pads, wet sanding with 1500 to 12000 pads. I wiped the surface with a soft moist cloth at the end of the micromesh cycle. The stummel looks amazing with a deep shine and beautiful grains over the stummel surface. Another issue that was addressed to a great extent was that of the minor scratches and nicks that were observed on the stummel. The rim top surface looks good with the few nicks and chips still visible, if observed closely. The refreshed fills distinctly stand out because of their dark coloration, and I shall let it be as a testimony of the journey of this beautiful pipe. I am very happy with the appearance of the rim top and stummel at this stage. I rubbed a small quantity of “Before and After Restoration Balm” in to briar and let it rest for a few minutes. The balm almost immediately works its magic and the briar now has a nice vibrant appearance with the dark hues of the grain contrasting with the rest of the stummel surface. I further buff it with a horse hair shoe brush. I set the stummel aside and took up the stem repairs. The tenon tip rebuild had cured nicely. With a flat head needle file, I sand the rebuilt portion of the tenon and the button edges to achieve a rough match. Using a round needle file, I shaped the opening of the tenon to a perfect round. I resorted to topping the tenon end on a piece of 220 grit sand paper to achieve the correct tenon size, which is just below the opening of the draught hole in the mortise. This ensures that the Pete’s famed “System” functions as effectively. I further sand the entire stem surface with a folded piece of a 220 grit sand paper to achieve a perfect blend of the fill with the stem surface. With the same piece of sand paper, I sharpened the button edges on both the upper and lower surface. I wiped the stem with a cotton swab and Murphy’s oil soap to further remove the oxidation and sanding dust. I rubbed some extra virgin olive oil into the stem and set it aside to be absorbed into stem. I polished the stem with micromesh pads, wet sanding with 1500 to 12000 grit pads. I rubbed a little extra virgin olive oil in to the stem at the end of all the micromesh pads. Next I rubbed a small quantity of extra fine stem polish that I had got from Mark Hoover and set it aside to let the polish work its magic. After about 10 minutes, I hand buffed the stem with a microfiber cloth to a nice shine. The stem is now nice, smooth and shiny. Now with the stummel nicely polished, the nickel band polished and shining and stem repairs and polishing completed, all that remained to be done was to get these parts together for a final polishing with carnauba wax. I glued the nickel ferrule to the shank end with CA superglue.To apply the finishing touches, I mount a cotton cloth buffing wheel on to my hand held rotary tool and apply a coat of Blue Diamond to the entire pipe to polish out the minor scratches. With a cotton buffing wheel that I use for carnauba wax, I apply a coat of carnauba wax to the stummel and stem and continue to work on it till the complete coat of wax is polished out. I mount a clean cotton cloth buffing wheel and gave the entire pipe a once over buff. I finished the restoration by giving the entire pipe a rigorous hand buffing using a microfiber cloth to raise the shine further. The finished pipe is shown below. P.S. – This is another unique and vintage pipe of my grandfather that has been passed on to me. I feel singularly fortunate and honored to carry forward his legacy while at the same time preserving a part of history of these pipe brands. Thanks for your patience and looking forward to inputs about the write up.

I had decided to let the fills be seen and not mask it under a darker stain; I am still open to suggestions from esteemed readers!!

 Cheers…

Another Fun Restore from Bob Kerr’s Estate – A BBB 2 Star Apple 11

Leave a reply

Blog by Steve Laug

Even with the COVID-19 warnings rolling in incessantly I am still working on pipes! It keeps my mind busy and focused and not to get carried away with the sense of powerlessness. There is no reason to not enjoy the time alone at the work table bringing these old-timers back to life. After brief foray restoring pipes referred to me by my local pipe shop I am back to Bob Kerr’s estate (his photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in over 60 restorations to date I thought that I would leave it out this time. Be sure to check out some of the recent Dunhill restoration blog (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

The next pipe I have chosen from his estate is an interesting looking Apple with a slender stem. It is stamped BBB in a diamond on the left side of the shank with a Star on each side of the diamond. On the right side of the shank it is stamped Made in England over the shape number 11. The slender stem does not bear the BBB brass logo. The tapered stem is oxidized and has tooth marks and chatter on both sides near the button. There is some calcification on the stem with damage to the button. The finish is worn and dirty. There is a thick cake and lava overflow on the rim top. There is some damage on top & edges. There appears to be some chips out of the thin rim top/edge that will need to be addressed in the restoration. Jeff took photos of the pipe to show its general condition before he did his cleanup. The finish on the pipe was very dirty – grime and grit from years of use and sitting fill the crevices in the rustication. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some darkening and chipping damage on the rim top. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides.Jeff took photos of the sides and the heel of the bowl to give a better feel for the grain around the bowl. He took a photo of the stamping on the sides of the. You can see that the stamping is very clear. On the left side it reads BBB in a diamond with a star on each side of the base. On the right side it reads Made in England over the shape number 11.The stem was dirty and extremely oxidized. Once again the stem appeared to be a replacement as I have learned Bob was a chewer and his stems seemed to have been replaced often. This one at least fit well to the shank and did not yet have the chew marks that were a norm on Bob’s pipes.Before I started my work on the pipe I decided to read a bit of BBB history to remind myself how the two stars fit into the hierarchy of BBB pipes. I turned first to Pipephil’s site (http://www.pipephil.eu/logos/en/logo-bbb.html). I have included a screen capture to show the stamping on the pipe. At this point I still did not know how it fit. Also the pipe I was working on did not have the BBB Diamond or Brass logo on the stem.I turned to Pipedia to see what I could gather there about the hierarchy of the Two Star pipe (https://pipedia.org/wiki/BBB). I read through the page and found some more information. I quote a pertinent section of the article that give the information that I was hoping for and expecting.

…In the Thirties, the top-of-the-range one becomes “BBB Best Make” with alternatives like “Super Stopping” and “Ultonia Thule”. The BBB Carlton, sold with the detail with 8/6 in 1938, is equipped with a system complicated out of metal, system which equipped the BBB London Dry too. Blue Peter was not estampillées BBB but BBB Ultonia, and the BBB Two Star (* *) become the bottom-of-the-range one.

Now I knew about where the Two Star fit – at the bottom of the range. Armed with that information it was time to work on the pipe. Jeff cleaned this filthy pipe with his usual penchant for thoroughness that I really appreciate. This one was a real mess and I was looking forward to seeing what he had done with this one when I took it out of his box. It looked amazing and CLEAN and other than the stem work needing a little effort on my part. He reamed the bowl with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks good with great looking grain around the bowl and shank. The rim top and front of the bowl was severely damaged with burns. The condition of the inner and outer edges was rough. The stem looked a lot better but damage was evident on the button. Jeff soaked the stem in Before & After Deoxidizer to remove the oxidation on the rubber. The pipe was ready for me to carry on the next part of the process. I took some close up photos of the rim top and also of the stem surface. I wanted to show how well it had cleaned up. The rim top was clean and the damage was very evident. There were several chips on the edge of the rim top with the largest being at the back of the bowl.  I also took close up photos of the stem to show how well surface looked on both sides. I took a photo of the stamping on the sides of the shank. You can see that it is stamped as noted above.I decided to start my restoration work on this one by dealing with the damaged rim top. I filled in the damaged areas with a drop of clear Krazy Glue (CA) and then pressed some briar dust into the glued areas with a dental spatula. I set the bowl aside to dry overnight.   I sanded the repaired areas with 220 and 400 grit sandpaper to shape the repaired areas and blend them into the rest of the bowl. I also worked over the edge and top to minimize the darkening to the edges.I polished the briar with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. After each pad I wiped the briar down with a damp cloth. I touched up the rim top colour with a Maple Stain Pen to match the colour of the rest of the bowl. I let it dry and buffed it by hand.I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. With that done the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I sanded out the remaining tooth marks and chatter with 220 grit sand paper to blend them into the rest of the stem surface. I started to polish it with a folded piece of 400 wet dry sandpaper. Once it was finished it had begun to shine.        I polished the stem with Denicare Mouthpiece Polish from a tin of it I have in the drawer here. It is a gritty red paste that I rub on with my finger tips and work into the surface of the stem and button and buff off with a cotton pad. It gives me a bit of a head start on the polishing work.  I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I am continuing to experiment with Briarville Pipe Repairs new product, No Oxy Oil so I rubbed the stem down with the oil on the cloth that was provided with it. This BBB Two Star 11 Apple was another interesting pipe to work on. It is a classic shaped Apple. It has a tapered vulcanite stem that I am pretty certain is a replacement stem. The grain on the pipe is very nice and the shape has a great look and feel in the hand. The smooth finish is beautiful and highlights the grain. The repaired rim top looks very good and blends in well. I polished stem and the bowl with Blue Diamond polish on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The deeply grained briar took on life with the buffing. The rich browns of the briar works well with the polished vulcanite stem. The finished pipe has a rich look that is quite catching. Have a look at it with the photos below. The shape, finish and flow of the Apple are very well done even with the replacement stem. The dimensions are Length: 5 ½ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. It is a beautiful pipe and one that will be on the rebornpipes store soon. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. 

A Fun Restore from Bob Kerr’s Estate – A Royal Crown Bulldog

1 Reply

Blog by Steve Laug

After brief foray into restoring pipes referred to me by my local pipe shop I am back to Bob Kerr’s estate (his photo is to the left). If you have not “met” the man and would like to read a bit of the history of the pipeman, his daughter has written a great tribute that is worth a read. Because I have included it in over 60 restorations to date I thought that I would leave it out this time. Be sure to check out some of the recent Dunhill restoration blog (https://rebornpipes.com/2020/01/01/restoring-the-last-of-bob-kerrs-dunhills-a-1962-dunhill-bruyere-656-f-t-bent-billiard/).

The next pipe I have chosen from his estate is an interesting looking Bulldog. It is stamped Royal Crown on the left top side of the shank. There is no other stamping on the shank sides or marks on the stem. The Saddle stem is oxidized and has tooth marks and chatter on both sides near the button. The finish is worn and dirty. There is a cake and lava overflow on the rim top. There is some damage on top & edges and the bowl is slightly out of round. Jeff took photos of the pipe to show its general condition before he did his cleanup work. The finish on the pipe was very dirty – grime and grit from years of use and sitting fill the crevices in the rustication. The rim top was covered with a coat of thick lava that overflowed the bowl. There was also some darkening on the rim top. The bowl itself had a thick cake with flecks of tobacco stuck in the cake on the sides.Jeff took photos of the sides of the bowl to give a better feel for the grain around the sides and heel of the bowl.He took a photo of the stamping on the top left side of the diamond shank. You can see that the stamping is very clear.The stem was dirty and very oxidized. The stem appeared to be a replacement and did not fit perfectly to the shank. It was diamond shaped and worked well on two sides of the shank but the other two were off. It did not have the characteristic bite marks that were on Bob’s pipes.Before I started my work on the pipe I decided to do a bit of research. I had no recollection of working on this brand before but I could be wrong as I have worked on a lot of pipes now. I turned first to Pipephil’s site (http://www.pipephil.eu/logos/en/logo-r6.html) and found out to my surprise that there was a connection to the Hardcastle brand. I have included a screen capture to show the link on the site to Hardcastle.From there I turned to Pipedia and was directed to the Hardcastle page. I turned to that page to see what I could learn about the pipe (https://pipedia.org/wiki/Hardcastle). I read through the page and found some more information. The Timeline for the Family Period (which is what I was interested in) is shown below. It seems to begin in 1903  when Edmund Hardcastle establishes the brand and ends 1946 when Dunhill buys out the shares and leaves the family to manage the company.

1903: Edmund Hardcastle establishes the brand

1936: Family sells 49% of the Hardcastle Pipes Limited shares to Dunhill

1946: Dunhill buys the remaining shares, but the family continues to manage the company

I did a screen capture of the Models and Grades of pipes in the Family Period. It shows the Royal Crown brand listed.Now I knew about the brand. Up until I had read this I thought it was a Danish made pipe. Now I knew that it was British made and came out of the Hardcastle factory. Armed with that information it was time to work on the pipe. Jeff cleaned this filthy pipe with his usual penchant for thoroughness that I really appreciate. This one was a real mess and I was looking forward to seeing what he had done with this one when I took it out of his box. It looked amazing and CLEAN and other than the stem work needing a little effort on my part. He reamed the bowl with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks good with great looking grain around the bowl and shank. The rim top and front of the bowl was severely damaged with burns. The condition of the inner and outer edges was rough. The stem looked a lot better but damage was evident on the button. Jeff soaked the stem in Before & After Deoxidizer to remove the oxidation on the rubber. The pipe was ready for me to carry on the next part of the process.  I took some close up photos of the rim top and also of the stem surface. I wanted to show how well it had cleaned up. The rim top was clean and the damage was very evident. There were marks across the top of the rim and damage to the inner beveled edge.  I also took close up photos of the stem to show how well surface looked on both sides. I also noted that the stem also is a replacement stem rather than the original as the fit against the shank is not perfect.I took a photo of the stamping on the left topside of the diamond shank. You can see that it is stamped as noted above.I decided to start my restoration work on this one by dealing with the damaged rim top. I topped it lightly on a topping board with 220 grit sandpaper. I remove the damaged surface of the rim top and then a folded piece of 220 to work on the bevel on the inner edge. The pipe looks much better than when I started. I polished the briar with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. After each pad I wiped the briar down with a damp cloth. I touched up the rim top colour with an Oak Stain Pen to match the colour of the rest of the bowl. I let it dry and buffed it by hand.I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. With that done the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I sanded out the repaired with 220 grit sand paper to blend them into the rest of the stem surface. I started to polish it with a folded piece of 400 wet dry sandpaper. Once it was finished it had begun to shine.I polished the stem with Denicare Mouthpiece Polish from a tin of it I have in the drawer here. It is a gritty red paste that I rub on with my finger tips and work into the surface of the stem and button and buff off with a cotton pad. It gives me a bit of a head start on the polishing work.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I am continuing to experiment with Briarville Pipe Repairs new product, No Oxy Oil so I rubbed the stem down with the oil on the cloth that was provided with it. This Royal Crown was another interesting pipe to work on. It is a classic shaped Bulldog. It has a saddle vulcanite stem that I am pretty certain is a replacement stem. The grain on the pipe is very nice and the shape has a great look and feel in the hand. The smooth finish is beautiful and highlights the grain. I polished stem and the bowl with Blue Diamond polish on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The deeply grained briar took on life with the buffing. The rich dark brown and black colour of the briar works well with the polished vulcanite stem. The finished pipe has a rich look that is quite catching. Have a look at it with the photos below. The shape, finish and flow of the Bulldog are very well done even with the replacement stem. The dimensions are Length: 5 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. It is a beautiful pipe and one that will be on the rebornpipes store soon. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. 

 

Final Pipe from the 19 Pipe Eastern Canada Lot – a Republic Era Peterson 1312 System

4 Replies

Blog by Steve Laug

I am finishing the last of the 19 pipes for the fellow in Kitchener, Ontario I decided to work on the last one of them. He had been referred to me by my local pipe and cigar shop. While I am not currently adding more pipes to my queue of repairs I have made a commitment to the shop to work on pipes for their customers. Generally they have one or two pipes that need a bit of work. This fellow sent me the following email:

I just came across my smoking pipes that I’ve had in storage for about 40 years. I’m wondering what you’d charge to have them refurbished. There are 17 in total (11 are Brighams and 6 are various).

It turns out he said he had 17 pipes. That was certainly more than I expected but I communicated that there was a large queue ahead of him and I would have to fit them in as I could. He was fine with whatever time it took. He sent me the following photos of his collection that he wanted restored. The first photo shows his eleven Brigham pipes – all very interesting shapes. The second photo shows the six various pipes in the collection – A Republic Era Peterson’s System 1312 (Canadian Import), A Bjarne Hand Carved Freehand, a Comoy’s Everyman London smooth billiard, a GBD Popular Dublin 12, an English made Kaywoodie Rustica 72B, a Kriswill Bernadotte 60 with a broken tenon. When the box arrived there were two additional pipes included for a total of 19 – a Ropp 803 Deluxe Cherrywood Poker and a Comoy’s Sandblast Everyman Canadian 296. It was a lot of pipes! I have been randomly choosing the next pipe to work on and chose the Bjarne Hand Carved Freehand that is shown in the second photo below. I have drawn a red box around the Peterson’s System Standard 1312 in the photo below. I have also put and X through all of the pipes that I have finished. I am making progress on the lot – I have finished all the pipes now.The 19th and last pipe that I took out of the box was a Peterson’s System Standard pipe. It had a smooth finish. It was stamped on both sides of the shank. On the left side it read Peterson’s System Standard. On the right side it was stamped Made in the Republic of Ireland and under that was the shape number 1312. The nickel ferrule was in great condition and was stamped K&P Peterson. There were faux hallmarks under that. The finish was probably the cleanest of the 19 pipes so I am glad it is the last one. The rim top had some lava on the flat surface and the inner rim is damaged and slightly out of round. The bowl appeared to have been recently reamed and not smoked since the reaming. The vulcanite stem was lightly oxidized and had tooth marks and chatter near the button on both sides. There was also some calcification around the button. I took close up photos of the bowl and rim top to show the condition of the bowl and the darkening and damage to the inner edge as well. You can also see the light lava on the rim and clean bowl. I also took close up photos of the stem to show its condition as mentioned above.   I took photos of the stamping on both sides of the shank to show what I was speaking about above. It is very readable. On the left side it reads Peterson’s System Standard. On the right side it read Made in the Republic of Ireland over the shape number 1312.  The nickel ferrule stamping is very readable and undamaged.    I have included the information on the shape number on this pipe that I picked up on researching the other pipes. It is a Peterson’s System Standard pipe with a 1312 shape number. The 312 is identical in shape, size and marking. I started my hunt for information by turning to a Peterson Catalogue that I have on rebornpipes and looked up the System Standard pipes (https://rebornpipes.com/tag/peterson-hallmark-chart/). I have put a red box around the 312 shown in the catalogue page shown below. That should give a clear picture of the size and shape of the pipe. But there was nothing to give me any information on what the first number 1 meant in the shape number 1312 that I am working on.Since this is stamped with the same “1” as previous Peterson pipes that I have worked on I turned to the blog and had a look. I am including the information on the unique numbering. Mark pointed me in the direction that I needed. I quote the pertinent part of his email. The underlined portion was the clue I was looking for on this pipe. I have already cleaned up several of Bob’s pipes that were sold through GT&C (Genin, Trudeau and Company, Montreal, Quebec).

The index at the back of the book is pretty good, and points you to all the GT&C goodies, but 155 has a photo from the catalog with your 1307, while 318 and 323 explain the rationale for the “1” prefix. In a nutshell, just drop the “1” and you’ve got the shape. My theory is that GT&C added this to aid them in warranty work, so they’d know the pipe was bought on Canadian soil.

I turned then to a previous blog I had written on a Kapruf 54 that had an odd shape number stamp and referred to the Canadian numbering system used by GT&C. Here it the link to that blog (https://rebornpipes.com/2019/08/09/back-to-bob-kerrs-estate-another-canadian-import-petersons-kapruf-a-54/). In the blog I included a link to a blog I did on the GT&C Catalogue that came to me in some paperwork the family gave me. I have included the cover of the catalogue and the page on the system pipes showing the 1312 shape. I have put a red box around the shape for ease of reference (https://rebornpipes.com/2016/09/13/petersons-pipes-brochure-from-genin-trudeau-co-montreal-quebec/). Be sure to check out the rest of the document on the link.

The GT&C Catalogue combined with the earlier Peterson Pipe Catalogue page make the link definitive. I am also including the information from Pipedia’s article on Peterson pipes. It is a great read in terms of the history of the brand (https://pipedia.org/wiki/Peterson). I have included a bit of the pertinent history here.

1950 – 1989 The Republic Era – From 1950 to the present time, the stamp for this era is “Made in the Republic of Ireland” in a block format generally in three lines but two lines have been used with or without Republic being abbreviated.

During the 1950’s and 60’s the Kapp & Peterson company was still in the ownership of the Kapp family. However 1964 saw the retiral of the company Managing Director Frederick Henry(Harry) Kapp.

Pipedia also included a section of information on the System pipes including a diagram of the sytems look (https://pipedia.org/wiki/Peterson#Republic_Era_Pipes). I quote a section of the article in part and include a link to another article on Pipedia on the System pipe.

The Peterson System pipes are the standard bearers of the Peterson pipe family, famous for the excellent smoking pleasure they provide. Often imitated but never equaled, the Peterson System smokes dry, cool and sweet, thanks to the scientific effectiveness of the original design. The heart of the System is the unique graduated bore in the mouthpiece. This makes the suction applied by the smoker 15 times weaker by the time it reaches the tobacco chamber. The result is that all the moisture flows into the reservoir and, thus cannot reach the smoker’s mouth. The Peterson Lip further enhances the effectiveness of the graduated bore by directing the flow of smoke upwards and away from the tongue. This achieves a uniquely even distribution of smoke and virtually eliminates any chance of tonguebite or bitterness. Furthermore, the shape is contoured so that the tongue rests comfortably in the depression under the opening. Each “PLip” mouthpiece is made from Vulcanite. For the Peterson System pipes to work properly, the stem/tenon has to have an extension, the tip of which will pass by the draft hole from the bowl and into the sump. Upon the smoker drawing in smoke, this extension then directs the smoke down and around the sump to dispense a lot of the moisture before the smoke enters the extension and stem. On the System Standards and other less expensive systems, this extension with be made of Vulcanite turned integrally with the stem. On the more expensive System pipes this extension will be made of metal which screws into the Vulcanite stem. This extension on the earlier pipes will be of brass and the newer pipes will be of aluminium. Most smokers not knowing this function of the metal extension, assumes that it is a condenser/stinger and will remove it as they do with the metal condensers of Kaywoodie, etc. Should you have a System pipe with this metal extension, do not remove it for it will make the System function properly and give you a dryer smoke (https://pipedia.org/wiki/A_closer_look_at_the_famous_Peterson_Standard_System_Pipe).

With that information in hand I knew what I was dealing with in terms of the stamping and the age of this pipe. I knew from the information that the pipe was made during the Republic Era between 1950 and 1989. Most of the pipes in this lot seemed to come from the 60s so my guess is that this is also a 60’s era pipe. I also knew that the pipe was brought into Canada by the Canadian Importer, Genin, Trudeau & Co. in Montreal, Quebec. Noting above that the catalogue postal code puts it in the late 60s early 70s which also fits the story. Now it was time to work on the pipe.

I cleaned up the thin cake in the bowl with a Savinelli Fitsall Pipe Knife and sanded the bowl with a piece of 220 grit sandpaper wrapped around a piece of dowel.   I used a folded piece of 220 grit sandpaper to clean up the top of the rim and to lightly bevel the inner edge to clean up the out of round bowl. I was able to make it look better.    I cleaned the mortise and the airway in the shank and stem with alcohol, cotton swabs and pipe cleaners. They were dirty but the pipe is clean now.    I polished the bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the rim down after each sanding pad to remove the dust and debris from the sanding. The rim top was looking very good after the final polishing pad.  I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine.    I set the bowl aside and turned my attention to the stem. I rubbed the stem down with Soft Scrub on with a cotton pad and it removed the oxidation. It was looking better.   I sanded out the remaining tooth marks, chatter and oxidation with 220 grit sandpaper and started the polishing with 400 grit wet dry sandpaper.     I rubbed down the stem with Denicare Mouthpiece Polish, a red gritty paste and a cotton pad to remove the remnants of oxidation and to blend in the sanding. The stem is starting to show promise at this point in the process.     I polished the stem with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. I wiped the stem down after each sanding pad with a cotton pad to remove the sanding debris.  I finished polishing the stem with Before & After Pipe Stem Polish – both fine and extra fine. I finished by wiping it down with Briarville’s No Oxy Oil and buffing it to a shine.     It feels good to be finishing the restoration of this 19 pipe lot from Eastern Canada. With the completion of this one I have finished the entire of the pipes. I look forward to the final look when it is put back together, polished and waxed. I put the bowl and stem back together. I polished the bowl and stem with Blue Diamond to polish out the scratches in the briar and the vulcanite. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The grain is quite stunning and really pops with the wax and polish. The shiny black vulcanite stem is a beautiful contrast to the browns of the bowl and thick shank. This Peterson’s System Standard 1312 Bent Billiard was a great pipe to end the restoration work on. The polished nickel Ferrule works as a contrast between the stem and the briar and binds it all together. It really is a quite stunning piece of briar whose shape follows the flow of the briar. The pipe is comfortable pipe to hold in the hand. The finished pipe is shown in the photos below. The dimensions of the pipe are Length: 6 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. This beautiful pipe will be going in the box with the others and be sent back to Eastern Canada. I look forward to hearing what the pipeman there thinks when he sees his collection now that it has been restored. Thanks for reading this blog and my reflections on the pipe while I worked on it. This was an interesting estate to bring back to life.

The 18th Pipe from the 19 Pipe Eastern Canada Lot – a GBD Popular 12 Dublin

Leave a reply

Blog by Steve Laug

With two pipes left to finish for the fellow in Kitchener, Ontario I decided to work on one more of them. He had been referred to me by my local pipe and cigar shop. While I am not currently adding more pipes to my queue of repairs I have made a commitment to the shop to work on pipes for their customers. Generally they have one or two pipes that need a bit of work. This fellow sent me the following email:

I just came across my smoking pipes that I’ve had in storage for about 40 years. I’m wondering what you’d charge to have them refurbished. There are 17 in total (11 are Brighams and 6 are various).

It turns out he said he had 17 pipes. That was certainly more than I expected but I communicated that there was a large queue ahead of him and I would have to fit them in as I could. He was fine with whatever time it took. He sent me the following photos of his collection that he wanted restored. The first photo shows his eleven Brigham pipes – all very interesting shapes. The second photo shows the six various pipes in the collection – A Republic Era Peterson’s System 1312 (Canadian Import), A Bjarne Hand Carved Freehand, a Comoy’s Everyman London smooth billiard, a GBD Popular Dublin 12, an English made Kaywoodie Rustica 72B, a Kriswill Bernadotte 60 with a broken tenon. When the box arrived there were two additional pipes included for a total of 19 – a Ropp 803 Deluxe Cherrywood Poker and a Comoy’s Sandblast Everyman Canadian 296. It was a lot of pipes! I have been randomly choosing the next pipe to work on and chose the Bjarne Hand Carved Freehand that is shown in the second photo below. I have drawn a purple box around the GBD Popular 12 Dublin in the photo below. I have also put and X through all of the pipes that I have finished. I am making progress on the lot – I have finished 17 pipes now and this is the 18th.The 18th pipe that I took out of the box was a GBD Popular. It had a smooth finish. It was stamped on both sides of the shank. On the left side it read GBD in an oval over Popular in script. On the right side it was stamped Made in England and under that was the shape number 12. The finish was really dirty and spotty looking. The rim top had a thick coat of lava on the flat surface and the beveled inner rim. The bowl had a thick cake in it that was hard and crumbling. The vulcanite stem was lightly oxidized and had tooth marks and chatter near the button on both sides. The GBD roundel on the left side of the stem looked good. It seemed to have tabs around the edges that held it on the stem surface.   I took close up photos of the bowl and rim top to show the condition of the bowl and the darkening and damage to the inner edge as well. You can also see the cake in the bowl. I also took close up photos of the stem to show its condition as mentioned above. I took photos of the stamping on both sides of the shank to show what I was speaking about above. It is very readable. On the left side it reads GBD in an oval over Popular.  On the right side it read Made in England over the shape number 12.  The stem also had a GBD Roundel on the left side of the taper.   Before doing cleanup work on the pipe I decided to do some research on the pipe. I looked first on the Pipephil website and found nothing on the Popular line. I turned to Pipedia and also was disappointed to find nothing on the line. Hitting the dead end I decided to turn to working on the pipe. I reamed the bowl with a PipNet pipe reamer to remove the cake. I cleaned up the remaining cake with a Savinelli Fitsall Pipe Knife. I sanded the bowl walls with 220 grit sandpaper on a piece of dowel to smooth them out. I was happy that the walls looked very good.   I scraped off the lava on the rim top with the edge of the Fitsall Pipe Knife. I used a folded piece of 220 grit sandpaper to clean up the top of the rim and the bevel on the inner edge. I was able to make it look significantly better. I cleaned the mortise and the airway in the shank and stem with alcohol, cotton swabs and pipe cleaners. They were dirty but the pipe is clean now.   I scrubbed the surface of the bowl and rim top with undiluted Murphy’s Oil Soap to remove the grimes, oils and tars and leave the surface clean. I rinsed it off with warm running water to remove the grime and the soap.   I polished the bowl and rim top with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the rim down after each sanding pad to remove the dust and debris from the sanding. The rim top was looking very good after the final polishing pad.     Once I had finished with the 2400 grit pad I touched up the colour of the rim top using an Oak Stain Pen. It blended very well with the colour of the bowl and shank. Once it cured I went on with the polishing with the remaining micromesh pads. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine.     I set the bowl aside and turned my attention to the stem. I rubbed the stem down with Soft Scrub on with a cotton pad and it removed the oxidation. It was looking better.     I sanded out the remaining tooth marks, chatter and oxidation with 220 grit sandpaper and started the polishing with 400 grit wet dry sandpaper.     I rubbed down the stem with Denicare Mouthpiece Polish, a red gritty paste and a cotton pad to remove the remnants of oxidation and to blend in the sanding. The stem is starting to show promise at this point in the process.  I polished the stem with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. I wiped the stem down after each sanding pad with a cotton pad to remove the sanding debris.  I finished polishing the stem with Before & After Pipe Stem Polish – both fine and extra fine. I finished by wiping it down with Briarville’s No Oxy Oil and buffing it to a shine.   It feels good to be one pipe away from finishing the restoration of this 19 pipe lot from Eastern Canada. With the completion of this one I have finished 18 of the pipes. I put the English Made GBD Popular 12 Billiard back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of Conservator’s Wax. I buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with the grain showing through the rustication on both sides and the smooth rim top. Added to that the polished black vulcanite stem was beautiful. This nicely finished GBD Popular Billiard is nice looking and feels great in my hand. Have a look at it with the photos below. The dimensions are Length: 5 ¾ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. Once again I am looking forward to what the pipeman who sent it thinks of this restoration. Only 1 more pipe to do in this lot! Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on the trust to the next pipeman or woman.

Breathing Life into a Brigham 3 Dot 333 Billiard

Leave a reply

Blog by Steve Laug

Not too long ago I received an email from a fellow in Kitchener, Ontario regarding some pipes he needed cleaned up. He had been referred to me by my local pipe and cigar shop. While I am not currently adding more pipes to my queue of repairs I have made a commitment to the shop to work on pipes for their customers. Generally they have one or two pipes that need a bit of work. This fellow sent me the following email:

I just came across my smoking pipes that I’ve had in storage for about 40 years. I’m wondering what you’d charge to have them refurbished. There are 17 in total (11 are Brighams and 6 are various).

It turns out he said he had 17 pipes. That was certainly more than I expected but I communicated that there was a large queue ahead of him and I would have to fit them in as I could. He was fine with whatever time it took. He sent me the following photos of his collection that he wanted restored. The first photo shows his eleven Brigham pipes – all very interesting shapes. The second photo shows the six various pipes in the collection – A Republic Era Peterson’s System 1312 (Canadian Import), A Bjarne Hand Carved Freehand, a Comoy’s Everyman London smooth billiard, a GBD Popular Dublin 12, an English made Kaywoodie Rustica 72B, a Kriswill Bernadotte 60 with a broken tenon. When the box arrived there were two additional pipes included for a total of 19 – a Ropp 803 Deluxe Cherrywood Poker and a Comoy’s Sandblast Everyman Canadian 296. It was a lot of pipes! I have been randomly choosing the next pipe to work on and chose the final Brigham that I have drawn a purple box around in the photo below.When I unwrapped it the pipe it was a nice looking smooth nicely grained Billiard that was stained with a rich brown colour. It was stamped on the smooth underside of the shank. The stamping was readable. The shape number 333 is on the heel of the pipe and identifies the shape. The stamping Made in Canada and then the Brigham stamp in script followed on the rest of the flattened shank. The age on this one is Post-Patent era, nominally 1960s. The rim top had a thick lava overflow from the thick cake in the bowl. The bowl was in decent condition and the inner edge appeared to be in good condition. There was some darkening around the top and inner edges of the bowl. It was a dirty pipe but the finish appeared to be in okay condition under the grime. The 3 Dot saddle stem was oxidized and had tooth marks and chatter near the button on both sides. There was also some calcification for about an inch up the stem. I took close up photos of the bowl and rim top to show the condition of the bowl and the rim edge as well as the cake and lava overflowing onto the rim top. I also took close up photos of the stem to show its condition as mentioned above.     I took a photo of the stamping on the underside of the shank to show what I was speaking about above. It is very clear and readable. The 333 shape number is on the heel followed by Made In Canada then the Brigham script logo.I removed the stem from the shank to reveal the aluminum tube/tenon that held the Rock Maple Distillator. The distillator was dirty and tightly jammed in the tube. It would need to be replaced. This is another non-Can. Pat. Brigham pipe from the nineteen pipe installment. This is the final, the eleventh of the Brighams. I went to work on it immediately. I reamed the bowl with a PipNet pipe reamer using the second cutting head to take the cake back to bare briar so I could inspect the walls. I cleaned up the remnants with a Savinelli Fitsall Pipe Knife. I sanded the bowl walls with 220 grit sandpaper on a piece of dowel to smooth them out and further examine them. I was happy that the walls looked very good. I scraped the rim top with a Fitsall Knife edge to remove the thick cake. I worked on the darkening on the rim top and the rough inner edge of the bowl with a folded piece of 220 grit sandpaper. I was able to remove the darkening and smooth out the inner edge of the bowl. I cleaned out the mortise area and airway to the bowl and the interior of the metal tube and airway in the stem with pipe cleaners, cotton swabs and alcohol. The aluminum tube was in better condition than others because the distillator had been used.  I scrubbed the surface of the bowl with undiluted Murphy’s Oil Soap and a tooth brush to remove the grime and grit as well as the remnants of the shiny finish on the smooth portions of the bowl.          I wet sanded the rim top and edges of the bowl with micromesh sanding pads – 1500-12000 grit sanding pads. I wiped the bowl surface down with a damp cloth after each sanding pad to remove the sanding dust. Once I finished the bowl looked good.   I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine.   I set the bowl aside and turned my attention to the stem. I rubbed the stem down with Soft Scrub on with a cotton pad and it removed the oxidation and the calcification build up. It looked a lot better.   This was the first of these pipes with some significant tooth indentations. Heating the vulcanite did not do anything to remove them so I wiped the stem down and filled them in with clear super glue. With this done I set the pipe aside and called it a night. Tomorrow I would address the stem.I sanded out the repairs to the tooth marks, chatter and oxidation with 220 grit sandpaper and started the polishing with 400 grit wet dry sandpaper. I rubbed down the stem with Denicare Mouthpiece Polish and a cotton pad to remove the remnants of oxidation and to blend in the sanding. The polish is a red gritty paste that works wonders on removing stubborn remnants of oxidation in the crease. The stem is starting to show promise at this point in the process. Before I finished the polishing stem I decided to fit it with a new Rock Maple Distillator.    I polished the stem with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. I wiped the stem down after each sanding pad with a cotton pad to remove the sanding debris.  I finished polishing the stem with Before & After Pipe Stem Polish – both fine and extra fine. I finished by wiping it down with Briarville’s No Oxy Oil and buffing it to a shine.     I am excited to finish last Brigham of the lot as it moves me one pipe closer to being finished. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with the grain popping through on the bowls sides and rim top. Added to that the polished black vulcanite stem with the shining brass pins was beautiful. This mixed grain on the smooth finish Brigham Exclusive Billiard is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. This 3 Dot Billiard is the last of the Brigham pipes that I have worked on in this collection. The dimensions are Length: 5 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 3/8 inches, Chamber diameter: ¾ of an inch. This is the 17th of the 19 pipes sent to me from Eastern Canada for restoration. Once again I am looking forward to what the pipeman who sent it thinks of this restoration. Lots more to do in this lot! Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next pipeman or woman.

Breathing Life into a Can Pat Brigham Exclusive 314 Pot

Leave a reply

Blog by Steve Laug

Not too long ago I received an email from a fellow in Kitchener, Ontario regarding some pipes he needed cleaned up. He had been referred to me by my local pipe and cigar shop. While I am not currently adding more pipes to my queue of repairs I have made a commitment to the shop to work on pipes for their customers. Generally they have one or two pipes that need a bit of work. This fellow sent me the following email:

I just came across my smoking pipes that I’ve had in storage for about 40 years. I’m wondering what you’d charge to have them refurbished. There are 17 in total (11 are Brighams and 6 are various).

It turns out he said he had 17 pipes. That was certainly more than I expected but I communicated that there was a large queue ahead of him and I would have to fit them in as I could. He was fine with whatever time it took. He sent me the following photos of his collection that he wanted restored. The first photo shows his eleven Brigham pipes – all very interesting shapes. The second photo shows the six various pipes in the collection – A Republic Era Peterson’s System 1312 (Canadian Import), A Bjarne Hand Carved Freehand, a Comoy’s Everyman London smooth billiard, a GBD Popular Dublin 12, an English made Kaywoodie Rustica 72B, a Kriswill Bernadotte 60 with a broken tenon. When the box arrived there were two additional pipes included for a total of 19 – a Ropp 803 Deluxe Cherrywood Poker and a Comoy’s Sandblast Everyman Canadian 296. It was a lot of pipes! I have been randomly choosing the next pipe to work on and chose the Brigham that I have drawn a green box around in the photo below.When I unwrapped it the pipe it was a nice looking rusticated pot that was lighter in colour than the other rusticated Brighams in the collection. It was stamped on the smooth underside of the shank. The stamping is faint but part of it was readable. The shape number 314 is on the heel of the pipe and identifies the shape. It is followed by the Can. Pat. 372982 and then the Brigham stamp in script. It had a rusticated bowl and shank with a smooth rim top. The rim top had a lava overflow from the medium cake in the bowl. The bowl was in decent condition, slightly out of round on the inner edge. There was some darkening around the top and inner edges of the bowl. It was a dirty pipe but the finish appeared to be in okay condition under the grime. The 3 Dot saddle stem was oxidized and had tooth marks and chatter near the button on both sides. There was also some calcification for about an inch up the stem. I took close up photos of the bowl and rim top to show the condition of the bowl and damage to the rim edge as well as the cake and lava overflowing onto the rim top. I also took close up photos of the stem to show its condition as mentioned above.     I took a photo of the faint stamping on the underside of the shank to show what I was speaking about above. It is very clear and readable. The 314 shape number is on the heel followed by the Can. Pat. 372982 number then the Brigham script logo.I removed the stem from the shank to reveal the aluminum tube/tenon that held the Rock Maple Distillator. The distillator was dirty and tightly jammed in the tube. It would need to be replaced. Before starting my clean up work on the pipe I turned to a chart that Charles Lemon of Dad’s Pipes sent to me on the patent era Brighams. There were made from 1938-1980. As the pipe I am working on is a Patent pipe, it’s more accurate to refer to its grade by name (the post 1980 grading scheme refers to Dots). Here is the  chart that Charles sent me. The pipe I am working on is thus a Brigham Exclusive with the 3 brass pins arranged in a triangle. With this pipe I am continuing to work on another Can Pat Brigham pipe from the nineteen pipe installment. This is tenth of the eleven Brighams. I went to work on it immediately. I reamed the bowl with a PipNet pipe reamer using the second cutting head to take the cake back to bare briar so I could inspect the walls. I cleaned up the remnants with a Savinelli Fitsall Pipe Knife. I sanded the bowl walls with 220 grit sandpaper on a piece of dowel to smooth them out and further examine them. I was happy that the walls looked very good.    I worked on the darkening on the rim top and the rough inner edge of the bowl with a folded piece of 220 grit sandpaper. I was able to remove the darkening and smooth out the inner edge of the bowl.    I cleaned out the mortise area and airway to the bowl and the interior of the metal tube and airway in the stem with pipe cleaners, cotton swabs and alcohol. The aluminum tube was dirty because it was missing the distillator and had been smoked sans filter.    I scrubbed the surface of the bowl with undiluted Murphy’s Oil Soap and a tooth brush to remove the grime and grit as well as the remnants of the shiny finish on the smooth portions of the bowl.     I wet sanded the rim top and edges of the bowl with micromesh sanding pads – 1500-12000 grit sanding pads. I wiped the bowl surface down with a damp cloth after each sanding pad to remove the sanding dust. Once I finished the bowl looked good.    I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine.   I set the bowl aside and turned my attention to the stem. I rubbed the stem down with Soft Scrub on with a cotton pad and it removed the oxidation and the calcification build up. It looked a lot better.        I sanded out the tooth marks, chatter and oxidation with 220 grit sandpaper and started the polishing with 400 grit wet dry sandpaper.     I rubbed down the stem with Denicare Mouthpiece Polish and a cotton pad to remove the remnants of oxidation and to blend in the sanding. The polish is a red gritty paste that works wonders on removing stubborn remnants of oxidation in the crease. The stem is starting to show promise at this point in the process.   Before I finished the polishing stem I decided to fit it with a new Rock Maple Distillator.  I polished the stem with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. I wiped the stem down after each sanding pad with a cotton pad to remove the sanding debris.  I finished polishing the stem with Before & After Pipe Stem Polish – both fine and extra fine. I finished by wiping it down with Briarville’s No Oxy Oil and buffing it to a shine.     I am excited to finish another of the lot as it moves me one pipe closer to being finished. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with the grain popping through on the rim top and the rustication coming to life. Added to that the polished black vulcanite stem with the shining brass pins was beautiful. This mixed smooth and rusticated finish Brigham Exclusive Pot is nice looking and feels great in my hand. It is light and well balanced. Have a look at it with the photos below. This is the smallest of the Brigham pipes that I have worked on in this collection. The dimensions are Length: 5 inches, Height: 1 5/8 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. This is the 16th of the 19 pipes sent to me from Eastern Canada for restoration. Once again I am looking forward to what the pipeman who sent it thinks of this restoration. Lots more to do in this lot! Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next pipeman or woman.

A Simple Refurbishing Of Peterson’s Barrel Pipe

Leave a reply

Blog by Paresh Deshpande

In the last couple of weeks, I have worked on three Peterson’s pipe, two from my inherited lot (DONEGAL ROCKY # 999 and KAPMEER # 120S) and one that I had purchased on eBay (PETERSON’S SYSTEM # 31)  just so that I could include it in my rotation. Continuing with my work on Peterson’s in my collection, the next pipe that is now on my work table is a rusticated Peterson’s “BARREL” with a thin delicate and long P-lip stem.

The rusticated stummel of this pipe has beautiful texture and feels tactile in the hand. A short shank with a nickel ferrule at the end and a long, tapered delicate P-lip stem makes it a visually stunning pipe. It is stamped on the bottom flat smooth surface at the foot of the stummel as “Peterson’s” in a cursive hand over “BARREL” in capital letters over “MADE IN THE” over “REPUBLIC” over “OF IRELAND” in capital letters. The shank end is adorned with a nickel ferule that is stamped as “K & P” over three faux hallmarks a Shamrock, a Prone Fox, and a Stone Tower. Further to the right, it is stamped as “PETERSON’S”. The stampings are crisp and easily readable less the Shamrock hallmark which has been slightly rubbed off.  Having researched and worked on a few early Peterson’s pipes, I knew that the stampings identified this pipe as being from Republic era i.e. 1949 to until the present, making it a newer generation pipe. Also during my search on Donegal Rocky # 999 pipe that I had researched earlier, I knew that BARREL belonged to the Group 4 basic entry level pipes from Peterson’s. Given below are snippets of relevant information that I had learned from pipedia.org:

Group 4, Basic Entry Level Pipes

In this group you will find the basic entry level pipes which many smokers desire and are most comfortable with for every day and rotation use. The two most famous and popular issues probably being the System and the Classic shape pipes. All of the pipes in this group can be purchased for relatively little cost and probably accounts for the majority of Petersons worldwide pipe sales

Tankard & Barrel: Two attractively shaped pipes finished in red polish or rustic. A quality briar fitted with a nickel mount. Available with Peterson lip or fishtail mouthpiece. Prices start from $45.With this information, I now know that this pipe is a pipe from the newer generation that is most comfortable and desired and I move ahead with my initial visual inspection.

Initial Visual Inspection
The pipe, as it sits on my work table, is dirty with a thick layer of cake in the chamber, a stummel that is covered in dust and grime and a military mount tapered vulcanite stem that is lightly oxidized. Here are a few pictures of the pipe before I proceed with a detailed visual inspection of each part of the pipe. The chamber has a thick cake with lava overflow over the rim top surface. The condition of the inner walls of the chamber will be ascertained once the existing cake has been taken down to the bare briar. The inner and outer rim edges appear to be in good condition, however, the same will be ascertained once the cake and lava overflow from the chamber and rim top respectively, is entirely removed. There is a very strong smell to the cake which, perhaps, may reduce appreciably after the chamber and the shank has been cleaned. The draught hole is right at the bottom and center of the wide and rounded heel of the stummel, making it an excellent smoker. The mortise is filled with oils and tars and specks of dried ash are seen on the walls of the mortise. The mortise is filled with dried oils, tars and gunk. The walls, however, are intact and well protected under the nickel ferule.  The rusticated stummel on this pipe is covered in a thick layer of dust and grime giving it a dull and lackluster appearance. The rim top surface is also covered in dust, lava overflow, grime and will need to be cleaned and polished. The nickel ferule at the shank end appears dull due to oxidation. The bottom of the ferrule has a patch that is heavily oxidized. The saving grace is that it is intact and undamaged.The tapered, thin and long slightly bent vulcanite P-lip stem is lightly oxidized with negligible, but visible on close inspection, scratches on either surfaces of the stem in the bite zone and over the P-lip. The shank end opening on the stem is constricted with dried oils and gunk. This should be a relatively simple cleaning up job of the stem.The Process
I began the process of refurbishing this pipe by reaming the chamber with a Castleford reamer tool, using size 2 followed by size 3 head. Using my fabricated knife; I further took the cake down to the bare briar. With a 150 grit sand paper, the walls of the chamber were rid of all the remnants of the cake, revealing smooth chamber walls. I further wiped the chamber with a cotton swab wetted with isopropyl alcohol to completely remove the sanding dust. I gently scraped the lava overflow from the rim top with a brass bristled brush. The inner and outer rim edge is in good condition. I scraped the shank internals with a fabricated tool to remove all the crud that had accumulated along the shank walls and further cleaned it with bristled and regular pipe cleaners dipped in isopropyl alcohol. I shall further draw out all the residual oils, tars and gunk by subjecting the chamber and the shank to a salt and alcohol bath. I continued the cleaning of the chamber and the short shank internals with a salt and alcohol bath. I use cotton balls which is an at par substitute as I have realized over the years. I draw out a wick from the cotton and along with a folded regular pipe cleaner; insert it in to the mortise and through the draught hole in to the chamber. Thereafter, I pack the chamber with cotton balls to about quarter of an inch below the rim inner edge and soaked the cotton balls with isopropyl alcohol up to the brim. About half an hour later, the level of alcohol had gone down, having being absorbed by the cotton. I topped it up once again and set it aside overnight. By next afternoon, the cotton and alcohol had drawn out all the remaining oils and tars from the chamber and mortise, fulfilling its intended task. I removed the cotton balls and ran pipe cleaners through the mortise to clean out all the loosened tars and gunk. Using my fabricated tool, I scraped out the entire loosed gunk from the shank walls and further cleaned it with alcohol and q-tips. The chamber now smells clean and fresh. I set the stummel to dry out naturally. Now that the internals of the stummel were cleaned, I scrubbed the external surface of the bowl with undiluted Murphy’s oil soap and hard bristled tooth brush. I deliberately cleaned the rim top surface with a soft bristled brass wire brush to remove the entire lava overflow and dried it using paper towels and soft cotton cloth. I rubbed a small quantity of “Before and After Restoration Balm” in to briar and let it rest for a few minutes. The balm almost immediately works its magic and the briar now has a nice vibrant appearance with the reddish brown hues of the raised rustications contrasting with the dark stummel surface. I further buff it with a horse hair shoe brush. With the stummel refurbishing completed, I turned my attention to the stem. The stem air way was filthy to say the least. Using a shank brush and dish washing soap, I cleaned the stem air way. I further cleaned the stem internals with hard and regular pipe cleaners and isopropyl alcohol. A lot of elbow grease and a pile of pipe cleaners later, when the pipe cleaners emerged white I knew that the stem internals were clean and fresh.With the stem internals now clean, I moved to external cleaning of the stem surface by dunking the stem in to “Before and After Deoxidizer” solution developed by my friend Mark Hoover. The solution helps to draw out heavy oxidation to the surface making its further removal a breeze, while the minor oxidation is eliminated to a very great extent. I usually dunk stems of 5-7 pipes that are in-line for restoration and the BARREL is marked in yellow arrow. I generally allow the stems to soak in this solution overnight for the solution to do its work.I sand the entire stem surface with a folded piece of a 220 grit sand paper to remove the tooth chatter and minor oxidation from the stem surface. With the same piece of sand paper, I sharpened the button edges on both the upper and lower surface. I wiped the stem with a cotton swab and Murphy’s oil soap to further remove the oxidation. I rubbed some extra virgin olive oil in to the stem and set it aside to be absorbed in to stem. I polished the stem with micromesh pads, wet sanding with 1500 to 12000 grit pads. I rubbed a little extra virgin olive oil in to the stem at the end of all the micromesh pads. I finished the polishing of the stem by rubbing a small quantity of Paragon wax and giving it a final polish with a soft cotton cloth. The stem is now nice, smooth and shiny.I cleaned the nickel ferrule at the shank end with a local compound that Abha, my wife, uses to polish her silver and gold jewelry and cutlery. This compound is a very fine powder and is least abrasive with fantastic results. The results were appreciated by Steve during his visit to India. The band is now a nice shining piece of nickle and provides a nice contrast to the shining black stem and the dark brown stummel. Unfortunately, I missed out on taking pictures as I was keen to finish this pipe!

To apply the finishing touches, I mount a cotton cloth buffing wheel on to my hand held rotary tool and apply a coat of Blue Diamond to the stem to polish out the minor scratches. With a cotton buffing wheel that I use for carnauba wax, I apply a coat of carnauba wax to the stummel and stem and continued to work on it till the complete coat of wax had been polished out. I mount a clean cotton cloth buffing wheel and gave the entire pipe a once over buff. I finished the restoration by giving the entire pipe a rigorous hand buffing using a microfiber cloth to raise the shine further. The finished pipe is shown below. P.S. – This was one of the easiest and most straight forward refurbishing works that I have undertaken till date. It was also a nice change from restoring pipes only from my inheritance. I am really privileged to have had an opportunity to carry forward the trust that the previous owner had posed in his pipes. Thanks for your patience and looking forward to inputs about the write up. Cheers…

Readying An Inherited Pete Kapmeer #120 S, Great Britain, For Its Second Inning…

Leave a reply

Blog by Paresh Deshpande

While going through the pile of my inherited pipes searching for my next project, I selected the DONEGAL ROCKY # 999 and this pipe, PETERSON’S KAPMEER # 120 S for restoration. Since I wanted to add Rhodesian shape to my rotation, I first restored the Donegal # 999. Thereafter other interesting pipes caught my fancy and this pipe was relegated to backseat. A few pipes later, as I was contemplating my next project, this pipe again came in to focus along with a few other Peterson’s which were languishing in the box and I decided to complete a few Peterson’s pipes during the next few days.

The shape of this pipe is a nice classic Dublin with a P-lip saddle stem. The deeply rusticated stummel feels tactile in one’s hand and the deep burgundy stain makes for a visual treat. It is stamped on the smooth underside as “120 S” towards the heel of the stummel followed by “PETERSON’S” over “KAPMEER” followed by the COM stamp “GREAT” over “BRITAIN” towards the shank end. The stampings are crisp and clear. The vulcanite P-lip saddle stem bears the trademark decorative letter “P”.During my research on Donegal Rocky # 999 (my first and only Donegal in my collection!!), I had read that KAPMEER belongs to the Classic Range of pipes offered by Peterson’s. These are basic entry level pipes and most of this line up is no longer in production. The COM stamp “GREAT BRITAIN” also points to this being an older pipe, that is, pre-1959.

Initial Visual Inspection
The pipe, as it sits on my work table, is dirty with thick layer of even cake, covered in dust and grime with a heavily oxidized stem. Here are a few pictures of the pipe before I proceed with a detailed visual inspection of each part of the pipe. The stummel has beautiful rustic patterns on this classic shaped pipe and is covered in a thick layer of dust and grime. The stummel appears dull and lackluster. However, the rich dark burgundy hues of the raised portions of the rustications contrast beautifully with the lighter hues of the stummel and would look more appealing once the stummel has been cleaned and polished. The end of the long and rusticated shank has a nice thin band of smooth briar. Once polished, this briar band should further enhance the beauty of this pipe. The meerschaum lined rim top is surrounded by briar wood and is covered in a thick coat of dust, lava overflow, grime and will need to be cleaned and polished. This lava overflow is chipped at places revealing an intact white meerschaum layer. The chamber has an even layer of thick cake that is sticky and hard. The condition of the meerschaum lined walls of the chamber will be ascertained once the existing cake has been completely removed. The inner meerschaum layered rim edge appears intact, however, the same will be ascertained once the cake and lava overflow from the chamber and rim top is removed. There is a distinct perfectly round ring above the draught hole which could be seen even through the cake and grime. Is it a crack? It is unlikely that a crack should be such a perfect round. It would require a closer inspection once the chamber has been cleaned. The mortise has a thick layer of black dried oils and tars on the walls which would need to be cleaned. The straight tapered vulcanite P-lip saddle stem is heavily oxidized and is peppered with light tooth chatter/ indentations on either surface of the stem in the bite zone and on the top surface of the P-lip. Heavy calcification is seen at the base of the edges of the P-lip. The button edges of the P-lip are deformed due to tooth marks and would need to be sharpened. The tenon end is covered in dried oils and tars. This should be a relatively simple repair and cleaning up job of the stem.The Process
I began the process of refurbishing this pipe with scraping out the calcification from the base of the button edges, cleaning the internals of the stem using pipe cleaners with isopropyl alcohol (99.9% pure) and dunking the stem in to “Before and After Deoxidizer” solution developed by my friend Mark Hoover. The solution helps to draw out heavy oxidation to the surface making its further removal a breeze, while the minor oxidation is eliminated to a very great extent. I usually dunk stems of 5-7 pipes that are in-line for restoration and this Kapmeer is marked in blue arrow. I generally allow the stems to soak in this solution overnight for the solution to do its work.Now that the stem is soaking in the deoxidizer solution, I worked the stummel, starting with reaming the chamber with a Castleford reamer tool, using only the second head. I was very gentle and careful while using the reamer head, applying minimum force for fear of cracking the meerschaum lining. Using my fabricated knife; I took the cake down to the meerschaum layer. With a 150 grit sand paper, the walls of the chamber were rid of all the remnants of the cake. My worst fears while working on meerschaum lined pipes were unraveled in front of my eyes!! There are two distinct cracks on either sides on the chamber walls, one each in 3 o’clock and 9  o’clock direction. These cracks are marked in yellow and orange arrows respectively. These cracks do not go all the way through the meerschaum layer, but are only superficial. The perfectly rounded crack that I had mentioned (marked in green arrow) earlier, is not a crack but just a circular line formed most likely by a reamer head. I further wiped the chamber with a cotton swab wetted with isopropyl alcohol to completely remove the sanding dust. I gently scraped off the entire lava overflow from the rim top with a sharp knife blade. The inner rim edge has no damage save for uneven surface. This issue will be easily addressed by a little sanding and polishing with micromesh pads. Just to allay my fears, I shared these pictures with Steve and Facetimed with him. I suggested that I coat the cracks with a mix of egg whites and chalk for repairs. However, Steve opined that these cracks are just superficial and that he would let them be. His closing remark was “that meer lining is going nowhere…”! At peace with my inner being, I move to the next stage.

I scraped the dried gunk from the walls of the mortise with my dental tool and further cleaned the shank internals with q-tips, pipe cleaners and isopropyl alcohol. I continued the cleaning till the pipe cleaners and q-tips came out clean.I scrubbed the external surface of the bowl with undiluted Murphy’s oil soap and hard bristled tooth brush and dried it using paper towels and soft cotton cloth. The burgundy hues of the raised rustications contrast beautifully with the rest of the stummel. I set the stummel aside to dry out naturally. I packed the chamber with paper towels to absorb any water and moisture that may have inadvertently seeped in to the meerschaum. To even out the rim top, I dry sand the top with 1500 to 12000 grit micromesh pads. I also polished the raised rustications and the thin briar band at the shank end, dry sanding with the micromesh pads to further enhance the contrast. I am really happy with the appearance of the entire stummel at this stage. I massaged a small quantity of “Before and After Restoration Balm” in to briar. I rubbed this balm deep in to the nooks and crannies formed between the rustications with my fingers and let it rest for a few minutes. The balm almost immediately works its magic and the briar now has a nice vibrant appearance with the dark hues of the raised carvings contrasting with the rest of the stummel surface. I further buff it with a horse hair shoe brush. I worked on all the stems that had been soaking in the deoxidizer solution overnight. I fished out all the stems and cleaned them under running warm water and scrubbed the raised oxidation from the stem surface using Scotch Brite pad. I further removed the oxidation by scrubbing the stems with 0000 grade steel wool and applied a little olive oil to rehydrate the stems and set them aside for the oil to be absorbed. Unfortunately, I did not click any pictures of these stems at this stage.

I painted both surfaces of the stem with the flame of a lighter to raise the tooth indentations to the surface. This also helps in loosening minor oxidation from the stem surface. I sand the entire stem surface with a folded piece of a 220 grit sand paper to remove the loosened oxidation. I wiped the stem with a cotton swab and Murphy’s oil soap to further remove the oxidation. I filled the tooth indentation in the button edge on both lower and upper stem surfaces with a mix of activated charcoal and CA superglue and set it aside for the fill to cure. Once the fill had cured sufficiently, I sanded down the fill with a needle file to match with rest of the stem surface. With the same file, I sharpened the button edge on both the upper and lower surface. I fine tuned the blending of the fill with the rest of the stem surface using a 220 grit sand paper and also sanded down the entire stem to remove the stubborn residual oxidation. I further sand the stem with 600 and 800 grit sand paper and wiped the stem with cotton pad dipped in alcohol to remove the resultant dust. I rubbed some extra virgin olive oil in to the stem and set it aside to be absorbed in to stem. However, I completely missed taking pictures of this stage.

I polished the stem with micromesh pads, wet sanding with 1500 to 12000 grit pads. I rubbed a little extra virgin olive oil in to the stem at the end of the micromesh pads polishing cycle. I finish the polishing of the stem by rubbing a small quantity of Paragon wax and giving it a final polish with a soft cotton cloth. The stem is now nice, smooth and shiny.I refreshed the stem logo by masking the logo with a whitener correction pen. Once the whitener had dried, I gently wiped the excess whitener away. The stem logo now looks prominent.To apply the finishing touches, I mount a cotton cloth buffing wheel on to my hand held rotary tool and applied a coat of Blue Diamond to the stem to polish out the minor scratches. With a cotton buffing wheel that I use for carnauba wax, I apply a coat of carnauba wax to the stummel and stem and continued to work on it till the complete coat of wax had been polished out. I mount a clean cotton cloth buffing wheel and gave the entire pipe a once over buff. I finished the restoration by giving the entire pipe a rigorous hand buffing using a microfiber cloth to raise the shine further. The finished pipe is shown below. P.S. – This was an easy restoration and the pipe turned out fabulously refreshed. I did enjoy working on it. Steve, with his practical and sound advice has been a great help. I cannot imagine this fun filled journey of mine without his help, guidance and encouragement. Thanks Steve for being such a big support and also for introducing some great friends in piper community.

I have three more Peterson’s pipes lined up and each one is interesting in its own way. I surely am looking forward to work on each one of them in the coming days!!

Thanks for your patience and looking forward to input about the write up. Cheers…

Refurbishing A Peterson’s Old English Collection Pipe.

2 Replies

Blog by Paresh Deshpande

In the last couple of weeks, I have worked on four Peterson’s pipe, two from my inherited lot (DONEGAL ROCKY # 999 and KAPMEER # 120S) and two that I had purchased on eBay, a PETERSON’S SYSTEM # 31 just so that I could include it in my rotation and a Peterson’s BARREL. Continuing with my work on Peterson’s in my collection, the next and fifth pipe that is now on my work table is a smooth Peterson’s “OLD ENGLISH COLLECTION” pipe with a thin delicate and long stem.

The smooth stummel of this pipe has beautiful mix of densely packed Bird’s eye grain on the sides and cross grain on the front and back of the stummel. The Duke shape (or more akin to the Tankard pipe from Peterson’s!!!) captures these grains beautifully for a stunning visual experience. A tallish stummel, short shank with a gold plated silver ferrule at the end and a long, tapered delicate stem makes it a visually appealing pipe. It is stamped on the bottom flat smooth surface at the foot of the stummel as “PETERSON’S” over “OLD ENGLISH” over “COLLECTION” in capital letters over “MADE IN THE” over “REPUBLIC” over “OF IRELAND” in capital letters. The shank end is adorned with a gold plated silver ferule that is stamped as “Peterson’s” in a cursive hand over “DUBLIN”. Further to the right there are three hallmarks in a cartouche, which unfortunately are worn off to the extent that I am unable to identify and make use of them for dating this pipe. Rest of the stamping on this pipe is crisp and easily readable. I would really be glad if any of the readers are able to make out these hallmarks and either share the same with us or describe them and help in dating this pipe. Since I have been working on Peterson’s pipes in my collection, I knew that these stampings identified this pipe as being from Republic era i.e. 1949 to until the present, making it a newer generation pipe. Also during my search on Peterson’s Barrel pipe that I had researched earlier, I knew that OLD ENGLISH COLLECTION belonged to the Collection Series of pipes from Peterson’s. Given below are snippets of relevant information that I had learned from pipedia.org;

Collections: Usually these popular themed collections of pipes are boxed.

They vary in price from the Ebony and Ivory at around $300 and up to $1000 for the River, 6 pipe set.

The Old English Collection: The old English Collection is no longer in production. It featured a set of 12 pipes, recreated using original classic designs from the 1930s and 1940s. Each pipe is handmade and mounted with gold plated sterling silver bands.With this information, I now know that this pipe is a pipe from the newer generation that is handmade and part of set of 12 pipes and I move ahead with my initial visual inspection. I would once again like to request readers of this blog to help me in pinning the exact date for this pipe.

Initial Visual Inspection
The pipe, as it sits on my work table, is dirty with an uneven layer of cake in the chamber, a stummel that is covered in dust and grime and a military mount tapered vulcanite stem that is heavily oxidized. Here are a few pictures of the pipe before I proceed with a detailed visual inspection of each part of the pipe.The smooth stummel on this pipe is covered in a thick layer of dust and grime giving it a dull and lackluster appearance. Through all the grime, beautiful Bird’s eye and cross grains can be still seen on the sides and front/ back of the stummel respectively. The rim top surface is also covered in dust, lava overflow, grime and will need to be cleaned and polished. The stummel has developed a nice patina which I shall endeavor to preserve. There are a few negligible scratches on the left side of the stummel which will be addressed during polishing the stummel with micromesh pads. There is one tiny but a slightly deep chip on the left side of the stummel, any repairs of which I shall take a call on subsequently. The chamber has a thin layer of uneven cake with lava overflow over the rim top surface. This overflow of lava is significantly more on the back of the rim top, in the direction of 6 ‘O’ clock. The condition of the inner walls of the chamber will be ascertained once the existing cake has been taken down to the bare briar. The inner and outer rim edges appear to be in good condition, however, the same will be ascertained once the cake and lava overflow from the chamber and rim top is entirely removed. There is a very strong smell to the cake which, perhaps, may reduce appreciably after the chamber has been cleaned. The mortise is filled with oils and tars and specks of dried ash are seen on the walls of the mortise. The walls, however, are intact and well protected under the gold plated silver ferrule.The gold plated silver ferrule at the shank end appears dull due to oxidation. It shows patches of heavy oxidation over the lower surface. The saving grace is that it is intact and undamaged.The slotted and slightly bent vulcanite stem is heavily and deeply oxidized with significant tooth indentations on the button edge and chatter on either surfaces of the stem in the bite zone. The tenon end shows traces of dried oils and tars. It’s going to take some elbow grease to clean up this stem to a nice deep and shining black. The Process
I began the process of refurbishing this pipe by using my fabricated knife to remove the thin layer of cake. I further took the cake down to the bare briar with a folded piece of 150 grit sand paper. Once the walls of the chamber were rid of all the remnants of the cake, chamber walls were found to be smooth and without any damage. With my modified and straightened cloth hanger, I cleaned the grime and cake that covered the draught hole at the heel of the stummel. I further wiped the chamber with a cotton swab wetted with isopropyl alcohol to completely remove the sanding dust. I scraped the shank internals with a fabricated tool to remove all the crud that had accumulated along the shank walls and further cleaned it with bristled and regular pipe cleaners dipped in isopropyl alcohol. I shall further draw out all the residual oils, tars and gunk by subjecting the chamber and the shank to a salt and alcohol bath.I continued the cleaning of the chamber and shank internals with a salt and alcohol bath. I use cotton balls which is an at par substitute as I have realized over the years. I draw out a wick from the cotton and along with a folded regular pipe cleaner; insert it in to the mortise and through the draught hole in to the chamber. Thereafter, I packed the chamber with cotton balls to about quarter of an inch below the rim inner edge and soaked the cotton balls with isopropyl alcohol up to the brim. About half an hour later, the level of alcohol had gone down, having being absorbed by the cotton. I topped it up once again and set it aside overnight. By next afternoon, the cotton and alcohol had drawn out all the remaining oils and tars from the chamber and mortise, fulfilling its intended task. I removed the cotton balls and ran pipe cleaners through the mortise to clean out all the loosened tars and gunk. Using my fabricated tool, I scraped out the entire loosed gunk from the sump and further cleaned it with alcohol and q-tips. The chamber now smells clean and fresh. I set the stummel to dry out naturally. Now that the internals of the stummel were cleaned, I scrubbed the external surface of the bowl with undiluted Murphy’s oil soap and hard bristled tooth brush. I deliberately cleaned the rim top surface with Scotch Brite and a soft bristled brass wire brush to remove the entire lava overflow and dried it using paper towels and soft cotton cloth. The rim darkening that I had observed over the rim top in 6 o’clock direction, was completely addressed. The inner and outer rim edges are in pristine condition. Thereafter, I polished the entire stummel with micromesh pads, wet sanding with 1500 to 12000 pads. I wiped the surface with a soft moist cloth at the end of the micromesh cycle. The stummel looks amazing with a deep shine and beautiful grains popping over the stummel surface. The rim top surface looks pristine with the issue of darkened inner edge entirely addressed. The second issue that was addressed to a great extent was that of the minor scratches and nicks that were observed on the left side of the stummel. One small nick can still be seen but to address it, I would have to compromise on the patina, which I did not desire. This minor nick is a part of the journey of this beautiful pipe and I shall let it be.  I am very happy with the appearance of the rim top and stummel at this stage. I rubbed a small quantity of “Before and After Restoration Balm” in to briar and let it rest for a few minutes. The balm almost immediately works its magic and the briar now has a nice vibrant appearance with the dark hues of the grain contrasting with the rest of the stummel surface. I further buff it with a horse hair shoe brush. With the stummel refurbishing completed, I turned my attention to the stem. The stem air way was filthy to say the least. Using a shank brush and dish washing soap, I cleaned the stem air way. I further cleaned the stem internals with hard and regular pipe cleaners and isopropyl alcohol. A lot of elbow grease and a pile of pipe cleaners later, when the pipe cleaners emerged white I knew that the stem internals are now clean and fresh.With the stem internals now clean, I moved to external cleaning of the stem surface by sanding the surface with a piece of 220 grit sand paper and thereafter dunking the stem in to “Before and After Deoxidizer” solution developed by my friend Mark Hoover. The solution helps to draw out heavy oxidation to the surface making its further removal a breeze, while the minor oxidation is eliminated to a very great extent. I usually dunk stems of 5-7 pipes that are in-line for restoration and the OLD ENGLISH COLLECTION is marked in green arrow. I generally allow the stems to soak in this solution overnight for the solution to do its work.Next day, I remove the stems from the deoxidizer solution and clean it under warm running tap water to remove all the solution. I scrubbed the stem surface first with scotch brite pad followed by a piece of 0000 grade steel wool. This helps in removing all the raised oxidation from the stem surface.  The deeper tooth indentations and chatter were raised to the surface by heating the damaged area with the flame of a lighter. I further sand the entire stem surface with a folded piece of a 220 grit sand paper to remove the raised tooth chatter and even out the stem surface. With the same piece of sand paper, I sharpened the button edges on both the upper and lower surface. I wiped the stem with a cotton swab and Murphy’s oil soap to further remove the oxidation. I rubbed some extra virgin olive oil in to the stem and set it aside to be absorbed in to stem. I polished the stem with micromesh pads, wet sanding with 1500 to 12000 grit pads. I rubbed a little extra virgin olive oil in to the stem at the end of all the micromesh pads. I finish the polishing of the stem by rubbing a small quantity of Paragon wax and giving it a final polish with a soft cotton cloth. The stem is now nice, smooth and shiny. I cleaned the gold plated sterling silver shank band with a local compound that Abha, my wife, uses to polish her silver and gold jewelry and cutlery. This compound is a very fine powder and is least abrasive with fantastic results. The results were appreciated by Steve during his visit to India. The band is now a nice shining piece of gold and provides a nice contrast to the shining black stem and the dark brown stummel. The patches of deep oxidation that were observed on the lower surface of the band were also completely eliminated. Unfortunately, I missed out on taking pictures as I was keen to finish this pipe and enjoy a bowl!

To apply the finishing touches, I mount a cotton cloth buffing wheel on to my hand held rotary tool and apply a coat of Blue Diamond to the stem to polish out the minor scratches. With a cotton buffing wheel that I use for carnauba wax, I apply a coat of carnauba wax to the stummel and stem and continued to work on it till the complete coat of wax had been polished out. I mount a clean cotton cloth buffing wheel and gave the entire pipe a once over buff. I finished the restoration by giving the entire pipe a rigorous hand buffing using a microfiber cloth to raise the shine further. The finished pipe is shown below. P.S. – This is indeed a beautiful piece of briar that exudes excellent craftsmanship and quality. Now I have set myself a target to acquire all the remaining 11 pipes to complete my personal collection. Thanks for your patience and looking forward to inputs about the write up. Cheers…