Tag Archives: shaping a stem

Restemming and Restoring a Made in Denmark Apple

Blog by Steve Laug

I got an email from a fellow in Dawson Creek, British Columbia asking if I would be willing to work on a pipe that he had that was one of his favourites. It was an apple that he really liked and he liked the patina on it as well. This is what he wrote to me: “Sir, I have a pipe in need of your skills. I was visiting City Cigar on a trip to Vancouver and William recommended you. I’ve inherited a pipe from my dad that needs to be refurbished. I wish to add a new curved stem. The old stem’s very loose. I will mail, or ship the pipe to you, as I live in Dawson Creek, BC. Once we discuss price & details. After leaving City Cigar, I was left with the impression that you’re “the guy” for the job.”

I asked him to send some photos of the pipe and give me a look at the pipe. The next two photos are the ones that he sent to me. The saddle stem looked like a replacement to me. I had him send the pipe to me for a closer look.When it arrived I could see that my assumption about a replacement stem was correct. Whoever had added the new stem had sanded the shank and removed half of the stamping on the shank. I could read that it said Made in Denmark and that there were no other stampings. The shank was significantly lighter in colour than the bowl. The rim was dirty and had a chip out of it and its top was damaged. There was some concrete rash on the back side below the chip where the bowl had been knocked on concrete. I took a close up photo of the bowl top to show the extent of the damage and the uneven cake on the bowl sides. I also took photos of the stem and shank junction to show how the shank had been sanded to meet the stem diameter.

I also took a photo of the back side of the bowl showing the horizontal line across the bowl. That line was a large fill that bulged and stuck out the surface of the bowl.The bowl was covered with a thick grime and sticky material. I wiped it down with a cotton pad and alcohol to remove the grime and get back to the finish. The grain really began to shine through once I had removed the gummy buildup. The left and right sides of the bowl showed some nice birdseye. The front and back showed cross grain that ran along the top and bottom of the shank. The birdseye ran along both sides of the shank.I topped the bowl on a piece of 220 grit sandpaper to remove the damaged portions of the rim.I sanded the backside of the bowl to smooth out the bulging fill that ran across the bowl.I sanded down the outer edge of the rim to remove the rim damage and also the burn and darkening on the edges. I scrubbed the bowl down with acetone and cotton pads to remove the finish so that once it was clean I could blend in the lighter portions with the rest of the bowl. The owner wanted a new stem for the pipe so I went through my can of stems until I found one that would fit. He wanted a taper stem and the one I found would suit the bill. He also wanted it to have a slight bend in the end. This sharply tapered stem would make that an easy fit and fix. The stem was slightly larger in diameter than the shank so I would need to reduce it to match.I took off the excess vulcanite with a Dremel and sanding drum. I worked on it until it match the shank diameter. I took it back to the work table to hand sand it. I used 180 grit sandpaper and took back the excess stem material.I sanded the stem further with 220 grit sandpaper until the transition between the stem and shank was smooth to the touch. I heated water in the microwave until it was boiling and put the stem in the water to soften it enough to put the bend in it. I bent it just enough to give it a jaunty look. I used the medium and the dark stain pen to touch up the shank. The combination of colours matches the rest of the bowl colour. I wet sanded the stem with 1500-2400 grit micromesh sanding pads to begin polishing it and to begin to remove the scratches. I rubbed it down with Obsidian Oil. I dry sanded it with 3200-4000 grit pads and gave it another coat of oil. I finished sanding it with 6000-12000 grit pads and gave it a final coat of Obsidian Oil. I set it aside to dry. I buffed the bowl and stem with Blue Diamond on the buffing wheel and polished the briar and the stem. The polishing took out the last of the scratches in the vulcanite stem. The fill on the back of the bowl blends in perfectly now and it is smooth to the touch. The transition from the stem to the shank is also smooth. The slight bend in the stem works well with the pipe. It is finished and ready to go back to Dawson Creek. Hopefully the owner will enjoy the new stem and the virtually “new pipe”. It still carries with it the memories of his dad giving it to him. It still as some of the marks of its story but the look and the feel of the pipe are better than when we began the journey. Thanks for looking.

A Pipe with a Story – an R.V.W. Handmade 5 pipe

3 Replies

Blog by Steve Laug

My brother sent me pictures of a pipe he found on eBay that grabbed his attention. It was not so much the pipe but the story of the pipe that caught his eye. He sent me the link and I had a look but was not sold on picking up the pipe. But he wanted it so he threw in a bid and won the pipe. He wrote to the seller and asked about it. He received a reply that the pipe had been found in Northern Michigan, US in a mud bank on the Rifle River – farm country in the middle of nowhere. They had no more information. The pipe was dark and looked like the mud bank it had been found in to my eye. The stem looked too long and the flow of the pipe did not work for me.The stamping on the pipe was pretty clear which surprised me. On the underside of the shank it read R.V.W over Handmade and then a 5 underneath that. That piqued my interest a bit so I decided to wait and reserve judgment until I saw the pipe. While I waited I did a bit of research and found out the pipe was made by Randy Wiley. I Googled to find his website and was directed to his Faceboook page. The link follows: https://www.facebook.com/wileypipes?__mref=message_bubble. I sent him a message on Facebook and related the story that my brother told me. I also included the above photos of the pipe supplied by the eBay seller. The next day I received a message back from Randy. Here is what he wrote: “Hi Steve, Wow, Glad there wasn’t a body with it. I’ll bet it was dropped while fishing. I’ve heard many stories. One day someone will find a pipe while scuba diving. I know the owner. This pipe is a second, RVW. It retails today for around $105.00”

When I first read his response I missed the part about him knowing the owner. This morning I read his response again as I was working on this blog and wrote Randy back regarding that line. I wonder if the original owner would want the pipe returned. We shall see.

When I was in Idaho I taught my brother to do the initial clean up on the pipes. It has been a real help for me. With the box of pipes to be refurbished filling up on this end it is really nice to have him work on them ahead of time. When I get them they have been reamed and the internals all cleaned so it makes my work much quicker. Because this one attracted his attention he really liked the cleanup of it. He reamed and cleaned the bowl and shank as well as the airway in the stem with pipe cleaners, cotton swabs and alcohol. He scrubbed the exterior of the bowl with a tooth brush and Murphy’s Oil Soap to remove the debris left behind by the mud bank. He took the following photos to show the pipe after his cleanup work. The straight grain on the left side, back and front of the bowl and the birdseye on the right side are beginning to show through. When I received the pipe I brought it to the worktable and took some photos of it before I began to work on it. While the grain was showing through it was still too dark to my liking. There were also many tiny nicks and pits in the surface from time spent in the mud by the river. These would need to be sanded out. The rusticated portions on the bowl sides and edges were also in need of deeper cleaning. The heel of the pipe had been knocked around and had many nicks and pits. The combination of smooth and plateau on the rim also needed deeper cleaning. The stem still seemed too long to me and if I end up either keeping the pipe or selling it I think I will make a second stem that is more proportional to the pipe in my opinion. The stem was oxidized but did not have any tooth marks or chatter. I ran the Savinelli Pipe Knife around the inside of the bowl out of habit with little effect because my brother had done a great job reaming this one.The bowl had some white debris in the bottom which I think was water marks from its time in the mud. I used alcohol pipe cleaners and cotton swabs to remove that debris. I scrubbed the exterior of the bowl and shank to remove more of the dark stain with acetone on cotton pads and was able to remove some more dark stain. There was more work to be done in this area but I would keep trying. I scrubbed the exterior with a bleach mixture to further remove the stain. The next photos show the effect of the bleach on the stain. The grain is beginning to show. I went through my stem can and found a nice amber Lucite stem that was the right length to my eye and would be a great contrast with the bowl. I did not have to do any fitting or tenon work as the stem fit in the mortise perfectly from the start. The stem was bent too much and would need to be straightened and bent to match the flow of the bowl. You can see in the photo below that the new stem is about an inch shorter than the one that came with it when I got it. I put the stem in place and took some photos to get an idea of how the pipe looked with the stem. You can also see the effect of the bleach on lightening the stain on the bowl in these photos. I used a Sharpie pen to darken the plateau areas on the end of the shank and the top of the bowl. I also used it on the rustications down the bowl sides and front. I used Watco’s Danish Oil with a Cherry Stain to stain the bowl. It is an oil based product and as it dries on the surface it darkens to a black cherry. I applied the stain with a cotton pad and let it absorb into the warm briar.When it had dried I buffed it off. The stain had darkened and with the natural darkening that had happened as the pipe lay in the mud the overall appearance almost a rich charcoal grey with red undertones. I forgot to take photos of the process of rebending the stem but what I did was boil water in the microwave in a cup and then heated the stem until it was flexible in the hot water. I inserted the tenon in the mortise and then bent the stem to match the flow of the bowl. I held the stem under cool water to set the new bend. There was some tobacco stains in the stem from a previous pipe it had graced. I cleaned it out with pipe cleaners and cream cleanser/soft scrub cleanser until all of the stains were gone.There was a groove in the stem on the top side about a ¼ inch from the saddle that I sanded out with 220 grit sandpaper. I worked over the stem with micromesh sanding pads – wet sanding the stem with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I sanded the bowl with micromesh sanding pads to try to lighten the dark cherry colour of the stain. I finished sanding it with 6000-12000 grit pads to polish the briar.While I was finishing polishing the pipe, I received an message from Randy regarding the previous owner of the pipe. He said that he had confused it with one that had been lost while scuba diving. So he could not remember who had purchased this one. I had also asked whether the stem was original and he was not certain.I actually found that to be good news as I did not like the stem that it came with.

I took the pipe to the buffer and buffed the pipe with Blue Diamond and then gave it several coats of carnauba wax. The briar has many small pits in the surface that I am convinced came from its time spent in the mud alongside the river. Part of me wanted to sand them out and remove them but another part, the part that won decided to leave them to bear witness to the shadow life this pipe had before it was found. I took the next photos with the blanket background as it seems to allow the grain to stand out a bit. The next photos I took against a light blue backdrop to show the contrast between the amber stem and the dark cherry stain. Thanks for looking.

Restoring ‘The Professor’ – WDC Milano Hesson Guard

3 Replies

Blog by Dal Stanton

This pipe was gifted to me in 1980 while a seminary student. I was Professor Freundt’s student assistant and I spent much time with him in his office which was a virtual jungle of books, papers and journals – heaped in piles here and there yet the professor knew where to find the most obscure minutia. Added to the smells of old books and leather covers were the tobacco and smoke that regularly provided an upper layer haze in his work space. The Professor introduced me to the art and enjoyment of smoking pipes – now some 36 years ago. I was young and eager, soaking in the ambiance of academia at a post-graduate level and pipes I discovered, were very comfortable partners in this environment. Professor Freundt gave me the Hesson Guard, showed me how to pack its first bowl in my hands, and I smoked it, adding my offerings to the perpetual haze. After these days, pipe smoking was put aside until last fall when Steve reintroduced me to it. At this point, 3 pipes made up my collection: a corncob I also bought during those seminary days to use while fishing and duck hunting, a Willard I received after my grandfather’s passing (a future restoration), and the WDC Milano Hesson Guard that I had tucked away in drawers over the past three and a half decades. Anxious to put a pipe back into service last fall, I grabbed the Hesson Guard, to clean it and do what I thought then were needed repairs…. I made a mess of the pipe – cracked the shank, reamed out the mortise so that the metal tenon was too loose – sloppy repair with super glue…. I’m anxious now to return to ‘The Professor’ (its given name) and try to make amends for the rough treatment he received last fall!

The right side of the shank is stamped with the well-known WDC inverted triangle next to Milano over Real Briar. The left side holds Hesson Guard. The bottom of shank had PAT. 1855800 which enabled me quickly zero in on the dating of the pipe. The patent application was submitted by the inventor of the special internals, William W. Hesson, in 1930 and granted two years later. An excerpt from the patent documentation describes the essence of the design:

The principal object of the invention is to provide a pipe which will eliminate contamination of the natural aroma of the tobacco through noxious secretions and which will remain sweet and clean. A further object is to devise a construction of pipe which will be simple and inexpensive to manufacture and which. will be devoid of pockets to harbor noxious elements. The principal feature of the invention consists in the novel arrangement of a tubular resilient member surrounding and embracing a metal stem which extends from the pipe bowl to the mouth piece and forming a seal to prevent the seepage of moisture around the metal stem.

(https://www.google.bg/patents/US1855800?dq=1855800&hl=en&sa=X&ved=0ahUKEwibqa2KsOjNAhUFVBQKHZ1DAvMQ6AEIGjAA)

I was curious to compare my Hesson Guard with the patent diagram which essentially is a long metal tenon meeting up with a metal sleeve at the base of the bowl and shank junction. This design, along with many other designs, was to eliminate the moisture build up, gurgle and gunk. Figure 1 (below) is followed by my overlay comparison picture – the tube inserts quite a way according to the 1930 design. Following are pictures telling the current story of The Professor: The pipe is attractive and has a good feel in my hand. The free-hand sculpting on the bowl gives the appearance of flames rising and is showcased in 3 paneled murals around the bowl. I notice that one of the panel dividers has been damaged at the top by cutting the briar. It looks like they were seeking to connect the panels – not sure. That will need to be filled in. The rim will also need some gentle repair to what appears to be nicks created by wear and tear. The cracked shank will need repair to keep it from growing and cleaning up the metal tenon and creating a good fit with the mortise might be a challenge. The bit has very mild tooth chatter. The last picture above captures not only the crack in the shank but the metal sleeve deep in the mortise that the chamfered tube/tenon docks with to create a dryer smoke – according to the patent information. Before any cosmetic restoration takes place I first must deal with the major issues of the shank crack repair and the tenon/mortise fit. I start the crack repair by drilling a small hole at the end of the crack to keep the crack from creeping up the shank. I use my Dremel tool and a 1.5mm drill bit to make the hole. I utilize a magnifying glass to trace the crack which had become a ‘hairline’. I’m careful not to drill too far and breach the mortise wall. Next time, I want to use a 1mm drill bit to leave less of a footprint. Next, after inserting the tenon into the mortise to expand the crack area for glue penetration, I create a mixture of briar dust and CA Instant Glue filling the hole and running a line of glue along the crack. I then sprinkle briar dust over the entire area and wait to dry. The timing worked out well as my wife just called me for lunch! After lunch, I work on cleaning up the tenon removing the old superglue with fingernails, Winchester knife, brass brush and 240 grit sanding paper – back in pristine shape. Well, after about a week, I return to the Milano Hesson Guard after my wife and I take advantage of the summer opportunities at the Black Sea coast. We enjoy some days at the beach near our favorite coastal fishing town, Sozopol. While at the beach, I thought about the Milano and how best to approach the overly loose tenon/mortise fit. Instead of applying clear nail polish around the metal tenon, which is what I did before, I attempt to rebuild the mortise wall by applying a very gentle coat of superglue on the inner wall of the mortise, rotating it as I applied superglue to achieve, what I hope, will be an even texture around the mortise wall. Amazingly, this seems to have worked! After drying, I gently reach into the mortise to remove some superglue ‘bumps’ with a needle file and I use a tightly rolled piece of 240 sanding paper carefully to smooth things down. I don’t want to inadvertently remove too much of the restored mortise wall! I also give the crack repair a light, strategic sanding with 240 grit paper, careful to guard the stampings. I refit the stem and to my relief, a snug fit was restored. With the stem refitting correctly and inserted, I return to the shank crack to finish sanding it to remove the excess superglue – I do this with stem in so as to not create unevenness between the mortise and stem shoulder. Satisfied with the shank crack repair and rebuilding the mortise wall, I put the stem in an Oxyclean bath for a soak to soften up the moderate oxidation buildup. I move my attention to the bowl to ream the mild cake down to the briar and then move to rim repairs and then to the panel repair. I want to have all these completed before looking at the general stummel cleanup and refinishing. I move out to the 10^th floor balcony adjoining my bedroom work station with Pipnet reaming kit to minimize the airborne cake soot – maximizing happy wife status! I started with the smallest reaming blade moving to use 3 of the 4 blades available to remove the moderate cake in the bowl. I finished the reaming by employing 120 grit paper on the chamber wall to remove remaining cake and smoothing the wall. I took a close up of the chamber and rim to show progress and to get a good idea of how to approach the rim repair. Inspecting the rim, I place a drop of superglue on one particular ‘dent’ that reached significantly down the external side of the bowl. I’m hoping that this small fill will enable me not needing to take as much off during the bowl topping to repair the rim. After the superglue sets up on the rim dent fill, I top the bowl using 240 grit sanding paper on top of a chopping block. Since the day is beautiful, I again move to the 10^th floor balcony to do the work. With the rim having no burns, I expect the surface to plane off evenly without pulls toward softer burned areas of the rim. I rotate in a clockwise circular even motion and take off only as much as needed to remove the damaged area of the rim. As I like to do, I create a small bevel on the inner wall of the rim to give a more finished, classier look. I use 120 grit paper to form the initial bevel angle followed by 240. I also decide to give the outer rim edge a slight sanding to round off the lip which seems to be consistent with the original Milano design. Again, I make the initial cut on the lip with 120 grit paper and finish off with 240. I have grown to appreciate more the rim presentation in finished pipes. To me, the rim, it’s nuances, are the first thing the eye is drawn to when looking at a pipe – much like the first thing one sees when looking a person are the eyes, then one follows by taking in the general appearances. The following pictures show the Milano’s rim progress. You can see in the immediate preceding picture the rim superglue fill spot at the 11 o’clock position of the rim and the ongoing panel repair just below it (to the left in the picture). Before moving to the stummel finishing, I now need to resolve the panel repair. I realize at this point with all the stummel repairs (cracked shank, topping and panel line), I will be removing the finish and refinishing the surface in order to achieve an even briar tone appearance. Now, continue to ‘heal’ the panel cut – earlier I applied superglue to it to build it up. I take a close up of the panel as it is now in order to know what I have. In order to blend more, I rough up the original superglue with a Dremel stone sander instrument. I apply on top of it a thick mixture of superglue and briar dust to form the restored surface that will join the side briar panel with the solid ring around the top of the bowl. I use toothpicks to mix, spread and tamp the mixture into place. I want this briar dust putty to setup well so I put the stummel aside for the time and turn to the stem which has been soaking in Oxyclean. The Oxyclean bath did the job of bringing the oxidation to the stem surface. I attack this initial layer with 000 steel wool and then use 240 grit paper to address the minor tooth chatter – I take pictures of bit top and bottom before starting to show progress. In order to have a good match between the mortise and the stem, I want to eyeball what the fit looks like before I proceed further. As I suspected, with all the superglue applied to the mortise area, the fit between mortise end and stem was not flush. I took the stummel back to the topping board and gently rotated the shank end on the board to regain a flush docking between stummel and stem. After a few rotation cycles and testings to eyeball things, I am satisfied. Before starting the micromesh cycles for the stem finishing, I need to remove the lip that I discovered with the shank end over the stem. With the topping of the shank end, I enlarged the circumference of the end just a bit so that it was a bit larger than the circumference of the stem shoulder – primarily on the lower side of the shank. I use 240 grit paper to even out the difference between the shank and stem – leaving the stem in place to assure a good, smooth transition! I am careful to use my thumb to cover and protect the nomenclature as I move around the shank with the sanding paper.Now to the panel repair below the rim. Using 240 grit sanding paper I bring the hardened superglue and briar dust mixture down to the bowl surface careful to maintain a rounded surface and not to flatten out the area of sanding focus. The pictures show the progress. Dal

I like the panel patch and it will blend with a darker stain. On a roll, I launch into the clean-up of the stummel and especially the ‘flame murals’ which are filled with grit and dust. I use a tooth brush with Murphy’s Wood Soap undiluted and work over the entire stummel with special focus in the fire sculpting to remove the surface finish. I follow this with rubbing down the stummel using cotton pads and tooth brush with acetone to remove the finish deep in the grain of the briar. I finish my clean-up of the surface by picking the carved crevices with a dental tool. Using micromesh sanding pads, I sand the high points of the stummel. Using 1500-2400 I wet sand. Following, 3200-4000 dry sand and finishing dry-sanding with 6000-12000. The pictures show the progress – I’m liking the briar grain the micromesh process is bringing out. At this point, I have two questions about how to proceed before staining the stummel. First, I need to clean out the ‘flame’ sculpting and use a black fine tipped permanent marker to darken the flames to give more contrast after the stain is applied. The other question was how do I treat the stampings of the WDC Milano – Hesson Guard? Do I protect it from the stain? Do I cover them with Vaseline? What? Upon closer inspection, I notice that the left side stamping, Hesson Guard, appeared to have gold left over in the ‘Hesson’ lettering – the rest having worn off (picture below) after the crack repair. After a quick email to Steve, his input revealed that both sides would have originally born the gold lettering. So, from my model kit (I’ve been involved in a project for several years building the USS Constitution sailing ship) I discover a bottle of Testors Gold Enamel Model Paint and my wife finds a small brush which I trim with my knife to create a more distinct point. With Steve’s counsel stored in my mind, I applied the paint over the lettering and wiped off the excess. To my relief and joy, the gold paint adhered to the crevices of the lettering and the overflow came off with the paper towel. My first stamping restoration with paint worked well! Steve also said that there was no need to worry about the new lettering during staining – that the gold paint would repel the stain. Careful to avoid the new gold lettering, I clean the bowl with isopropyl using a tooth brush to get rid of the residue from the sanding and then I move to highlighting the flame sculpts to bring greater definition to the paneled murals in the finished pipe. The pictures tell the story. Time to stain and I decide to use a mixture of an alcohol-based Italian stain I found here in Bulgaria with a color description of dark nut. I want this as the base, but I mix it with a mahogany color water based stain to bring out a slightly more redish tone in the briar. I think the red will work with the flame sculpting motif and I think this will look good – but of course the briar does what it will with the hues! After mixing the stains in the shot glass, I apply the mixture to the stummel mounted on the cork and candle stick with cotton balls making sure to cover everything and getting a good thick coverage. After applying stain, I use the butane lighter to flame the stain. With the mixture that I made, the alcohol content was too low to ‘flame’ so I evenly moved the lighter flame across the surface to evaporate the alcohol setting the dye in the grain of the briar. I repeated the process again and set the stummel aside to dry.With the stummel put aside, I turn again to the stem. I re-inspect the button area after the earlier sanding to remove the teeth chatter. I decide that the button needed a little more attention. I use 240 grit sanding paper and a needle file to fine-tune the shape of the button before starting on the micromesh cycles. I wet-sand the stem using 1500-2400 and complete the cycle by applying Obsidian Oil. While still wet from the oil I continue to dry sand with 3200-4000 micromesh pads, again concluding the cycle by applying Obsidian Oil. The final cycle, 6000-12000 is used and a final coat of Obsidian Oil and I put the stem aside to dry. I love watching the shine of the stem progressively make it to the surface getting that final wet, reflective look in the stem. Nice! The stem pops. The pictures capture the progress! For me, beginning the process of finishing the stummel after the staining dries, is like opening a Christmas present. The anticipation is to see what actually is under the crust of flamed stain and what the briar grain will reveal. With the Dremel tool, I begin to remove the ‘wrapping’ using a felt wheel. Also with a felt wheel I polish beginning with Tripoli and then move to Blue Diamond. I focus on bringing out the contrast of briar ‘flames’ showcased in the three panels. I switch to a cotton cloth wheel and apply carnauba wax to both stummel and stem. After several coats of carnauba, I complete the job by giving the pipe a clean cotton cloth wheel buff followed by a rigorous buffing with a micro-fiber cloth to bring out the deep tones of the briar. I’m pleased with the revitalization of ‘The Professor’, WDC Milano Hesson Guard. I think Professor Freundt, if he were alive today to comment, would agree. The rich dark tones of the briar, with the hints of deep reds, reminds me of the myriads of leather bindings and books that filled his hazy office. I’m pleased with the results. Thanks for joining me!

Restoring a Chubby Shank Bruyere Shop Apple

3 Replies

Blog by Steve Laug

This one came to me in the box of pipes from my brother, Jeff. It is stamped Bruyere Shop on the left side of the shank and Imported Briar on the right side. It has a sterling silver band that is stamped STERLING and bears three hallmarks – an Anchor, a Lion and a T. The band thus reads Birmingham (the Anchor), .925 Sterling Silver (the Lion) and the letter T which dates the pipe to 1943. The band appears original as there are no cracks that it is banding or repairing. There is no damage to the pipe under the band. The silver band was oxidized and tarnished. It is pressure fit on the shank. The bowl was in decent shape when I got it – dirty and worn. There were paint specks on the briar. The beveled/rounded rim had darkening and heavy coating of tars and oils. The bowl had a cake that cover the sides and bottom. The thick shank was extremely dirty and oily. The stem had tooth marks on the top side and the underside next to the button. It was oxidized and very dirty as well. I took a close-up photo of the rim to show the buildup and the cake in the bowl. The second one shows the stamping on the band that I spelled out above.The next two photos show the condition of the stem and show the oxidation and the tooth marks next to the button.I scrubbed the bowl and rim with acetone on cotton pads to remove the old wax and grime on the finish. I worked on the rim to remove the buildup that had collected there. I used the Savinelli Pipe Knife to cut back the cake to bare briar.I sanded the inner edge and top of the rim to clean off the tarry buildup and also smooth out the dents and nicks in the rim.I scraped out the shank with a dental spatula and scrubbed the shank with pipe cleaners, cotton swabs and alcohol until it was clean.I polished the silver band with silver polish to remove the tarnish and oxidation. The bright shine of the sterling silver came through the polish and I could see that it was going to be a beauty once the tarnish was gone.I used a light brown stain pen to restain the rim and polished it.I buffed the bowl lightly with Blue Diamond to polish the briar. I buffed it until the bowl and rim matched each other. I sanded the stem with 220 grit sandpaper to remove the tooth marks on the top side of the stem. I repaired the one on the underside with black super glue. I built up the top of the button on both sides of the stem with black super glue. I sprayed it with an accelerator to dry it quickly.I used a needle file to rehape the sharp edge of the button and smooth out the surface of the stem.I cleaned out the airway with pipe cleaners and alcohol to remove all of the oils and tars in the stem.I sanded the stem with 220 grit sandpaper to remove all of the oxidation. I wet sanded the stem with 1500-2400 grit micromesh sanding pads. I gave the stem a coat of Obsidian Oil and dry sanded it with 3200-4000 grit pads. I gave it another coat of oil and sanded it with 6000-12000 grit pads. I gave it a final coat of oil and set it aside to dry. I buffed the stem and bowl with Blue Diamond on the buffing wheel to polish it. I gave the bowl and stem multiple coats of carnauba wax and buffed it with a clean buffing pad to raise the shine. I hand buffed it with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. If anyone knows anything about the Bruyere Shop please let me know in the response below. Thanks for looking.

ADDENDUM

I was doing some reading on the web and found a reference to a pipe shop in Buffalo, N.Y. called the Bruyere Pipe Shop in a May 1953 Popular Mechanics Magazine. I wonder if there is a tie…

Sofia Hole in the Wall #3: A Butz-Choquin Rocamar with a Cumberland stem

9 Replies

Blog by Dal Stanton

This is my third restoration from what I called the ‘Bag of 4’ that Steve and I saw at the ‘Hole in the Wall’ antique store during his visit to Sofia, Bulgaria. Thanks again for indulging my ‘newbie’ offerings. My favorite of the bunch was a Savinelli Tortuga (https://rebornpipes.com/2016/06/18/sofia-hole-in-the-wall-find-savinelli-tortuga/). The second, which I didn’t write up, was a beautiful Danske Club Vario, which I discovered on Pipedia is a Stanwell second. Behind the Tortuga, the Vario was a close second. It is now next to my Tortuga in regular rotation – a great addition to my growing collection. Take a look at a few pictures of the finished Danish Danske Club Vario. I’m drawn to the blended smooth and sandblasted briar finishes on this pipe: The markings I found on pipe #3 on the left side is Butz-Choquin over Rocamar with a ‘Filter 9’ diagonal imprint. On the right side, St. Claude, France 1333, which I assume is the BC shape or series number. The Cumberland stem has the BC imprinted marking. From Pipedia I discovered a bit of the early history of the name from Pipedia:

“Jean-Baptiste Choquin of Metz started out as a tobacconist. This enterprise was prosperous; he had several employees. Among those, there was a certain Gustave Butz who was its first workman and who became his son-in-law by marrying Choquin’s daughter Marie in 1858. In 1858 Jean-Baptiste Choquin created, in collaboration with Gustave Butz, the Choquin pipe. This bent pipe with a flat-bottomed bowl was finished with an albatross-bone mouthpiece, fixed with silver rings. In 1858, still in Metz, Gustave Butz built an establishment for the manufacture of the Choquin pipe which took the name of -. In 1951, the Berrod-Regad company bought the trademark, continuing manufacture until 2002. Departing from Metz, the workshop was relocated to Saint-Claude, then also called ‘the world capital of the briar pipe,’ under the Berrod-Regad group.”

I could find nothing specific about the series name Rocamar so I decided to send an email to Butz-Choquin using their info contact from their current website which is under construction (http://www.butzchoquin.com/). We’ll see where that goes.

The BC Rocamar has an attractive fiery grain and the bent billiard chimney is tall and elegant to me – perhaps tending toward an egg shaped bowl. What I’m drawn to also is the bent Cumberland stem – my first to work on. Not quite knowing what kind of stem it was I did a bit of research and discovered pipesmokersforum.com a thread discussing this stem:

“Cumberland proper is a vulcanite rod made up from red and black rods, melted and swirled together for the brown/red marble effect. It is very soft, and oxydizes fairly quickly if the protective wax coating is scraped off. There is a harder version in ebonite, which has a higher sulfur content if I understand these things correctly, but the color combos are not quite as subdued as the vulcanite version. It’s a bit more “brick” colored.” Another comment I read was that if one found a Cumberland stem it was most likely hand cut – to me that is cool. Helpful information. Here are pictures of the BC Rocamar when it arrived home from the Hole in the Wall: The briar is in great shape and will need basic clean-up. The rim shows a burn scar about 2 o’clock and lava build up. As the comments about Cumberland stems and oxidation stated, this one had its share. The bit has significant teeth chatter and some significant divots that will need repair. Yet, I see the potential of the color swirl of the Cumberland being a very nice augmentation to the fiery briar stummel. The filter casing had dislodged from the stem and that will need to be reattached. I decide to drop the stem in an Oxyclean bath to start working on the oxidation while I turn my attention to the bowl – whoops, that is after I retrieved the stem from underneath the bed – I forgot it was on my lap when I stood to head for the Oxyclean! I took a close-up of the rim and bowl before I go to work. I moved from the bedroom work table to the 10^th floor balcony mobile work station with Pipnet reaming kit in hand. I want to minimize pipe soot being released into the bedroom atmosphere resulting in a happier wife. I use only the two smallest blades from the reaming kit to take the cake down to the wood. I finish the fire chamber by rubbing it with 120 then 240 grit sanding paper to smooth and clean the chamber walls even more. Turning to the rim, I clean it with isopropyl 95% and a brass brush which will not scratch the surface of the bowl. I want to see the rim wood clearly before I top the bowl to repair the burn scar and reveal the briar. With the sunshine helping I can see the rim (and holding tightly not to lose it over the edge!). I note that the rim circumference is small as the sloping shape of the bowl culminates. I move to top the bowl but with a view to take off as little as possible to preserve the dimensions of the slender egg-peeked chimney of the bowl. With the stem soaking in the Oxyclean bath I’m not able to reattach it to the stummel to help make sure I’m maintaining a true perpendicular top and not leaning into the softer burned area. Before rotating the bowl to top it, I let it free stand and gently rotated the pitch of the bowl so that I could ‘feel’ the low spot where the rim was burned. By doing this I was able to acclimate to the ‘healthy’ flat part of the rim during the sanding rotation. It worked well! I took a picture after only a few rotations on the topping board. It revealed that I wasn’t fudging into the low spot as it was not yet impacted by the sanding but the other ¾ of the rim was. I’m careful to keep eyeballing the progress. I use 240 grit paper on a chop board as my topping table. Moving in a circular, even motion I remove only what is needed. Satisfied with the topping, I made a small bevel on the inside of the rim using 120 and 240 grit paper. I did this to take out a bit of inner rim damage and a small bevel is always nice and gives a classy touch. I followed this by using micromesh (1500-12000) on the rim to remove all scratches. The pictures tell the story. I decided to wait on staining the rim using a stain-stick and move to the cleaning of the internal and external of the bowl. The reason I did this was I was able to differentiate the actual unstained color of the briar by looking at the newly repaired rim and compare it to the bowl color. The rim briar leaned brown whereas the bowl, to the reds. With cleaning with Murphy’s Soap of the external bowl, I expect there to be a slight change in the color of the bowl briar. At that point I would go to work again on the color of the rim aiming for the best match. I decided at this point to move to cleaning the internals of the stummel with Q-tips and pipe cleaners dipped in isopropyl 95%. I found the internals to be amazingly free of muck and it was not long before Q-tips and pipe cleaners were coming out clean. Turning to the external cleaning, I used Murphy’s Soap undiluted with cotton pads to remove the wax and grime on the bowl. The bowl itself is in great shape – no significant scratches or fills. At this point, I came to a road block which necessitated a quick email to ‘Master Obi-wan Steve’ for his input. After the Murphy’s Soap cleaning I was expecting/hoping the high gloss finish on the bowl to have been dulled – getting to a more natural grain look not competing so much with the bared rim – at least this is what was in my mind. My hesitations were not wanting to be too aggressive with the bowl finish and mess up the patina that is under the gloss…. With the time difference between Sofia and Vancouver, I put the stummel aside and turn to the much anticipated work on the Cumberland stem – what to me is the unique part of this BC stummel/stem ensemble. After I extract the stem from the Oxyclean bath, I take some pictures to chronicle the progress. After an initial buff with 000 steel wool to remove the surfaced oxidation, I take a closer look at the significant teeth divots on the bit and decide to apply super glue to the top and bottom to be able to redefine the button and cover the chatter damage. I want the superglue patches in place before beginning the sanding of the stem. With the superglue curing, Steve’s reply came about my bowl conundrum and it is now decision time. He suspects that I’m dealing with a urethane finish much like he just dealt with in a Jobey restore (https://rebornpipes.com/2016/06/29/i-thought-this-one-would-be-easy-boy-was-i-wrong/) that was a bear to remove. The options before me are to either come up with a high gloss finish for the rim seeking to match up with the bowl or to aggressively remove the plastic, gloss finish and rescue the beautiful briar beneath. The close-up picture below revealing the bare briar in rim repair sealed my decision – I put the bowl in an overnight alcohol bath hopefully to soften the glossy finish to be revisited tomorrow. The time had come to watch some European football – Portugal and Poland – on my widescreen HDTV in my favorite recliner.The next day, with Poland and Portugal playing to a 1-1 tie the night before, I was anxious to see if the alcohol bath made a dent on the glossy finish. Upon inspection (picture 1) it was still pretty shiny so I took a light grit sanding sponge to loosen the finish. I was careful to lightly work around the nomenclature. This did the trick. The alcohol bath undoubtedly softened things up. After the sponge sanding, I followed with rubbing the bowl with acetone with cotton pads to draw the stain out of the grain. I finished with wiping down the stummel with isopropyl 95% to make sure all was cleaned and no grit left behind. I feel like I’m on a roll and I’m anxious to see the grain of this piece of briar unveiled. I use micromesh pads from 1500 to 2400, 3200 to 4000, and 6000 to 12000. The pictures below show the progress. I have to be honest, this is perhaps my favorite part of the restoration process – each set of micromesh pads brings out more of the grain revealing the profoundly unique ‘fingerprint’ of each piece of briar we handle. I euphemistically think of micromesh pads as ‘magicmesh’ pads – they bring the wood to life. In my opinion, the grain that I’m now enjoying is much more satisfying than looking through the plastic shiny sheen of the original Butz-Choquin design. I decide to put the bowl aside and focus now on completing the Cumberland stem clean up and restoration. I want to have an idea of the colors of the finished stem before I decide on the best finish for the stummel. I like working on a clean stem so I first clean the airway using pipe cleaners and Q-tips dipped in isopropyl 95%. During the cleaning, I saw something that I had missed before. The button airway opening has a divot – I’ll need to add that to the list. The superglue applications on the bit and button have had plenty of time to dry. I use 240 grit sanding paper and needle files to work on the bit and button repair. The bit repair looks good so I move to micromesh and the homestretch. I wet sand using 1500-2400 and then apply Obsidian oil to the stem. At this point, I inspect the repair work on the bit to make sure there are no scratches that I’ve missed before proceeding. I’ve learned that often scratches are covered by the rough vulcanite. With the Obsidian oil on the stem I dry-sand using micromesh pads 3200-4000 and apply more Obsidian oil. I do the same with the last set of three – 6000-12000 and give a good coat of oil and put it aside to dry. The pictures show the progress rejuvenating the Cumberland stem. I like what I’m seeing. I had one undone job – re-attach the filter casing to the stem. My assumption is that it was initially glued and after inspecting the inside of the stem, I detected residue that I assume was the glue previously used. I clean the old gunk off the housing and the inside of the stem with alcohol and cotton pad and reattach the housing with superglue. To get the job done I used my Winchester pocket knife and a dental pick to dig out the old glue. With the filter housing reattached, the stem is complete. I really like the rich color of the Cumberland stem. After allowing the filter housing glue to dry I want to see the lay of the land, I rejoin the Cumberland stem to the stummel (picture #1 below). I decide to stain the bowl with a new stain I found at the German owned ‘Mr. Prakteker’ – like Home Depot in the US. Finding alcohol-based stains in Bulgaria has been a challenge so I’ve been mixing my own batches up to this point. The brand is Italian and the cost was a bit more – I’m hoping that translates into better quality. When I opened the tin, a whiff of the stain revealed alcohol. With the help of Google Translate, the flavor of the stain is Dark Nut. The Bulgarian stick-on information tag said Dark Walnut. My thinking is to aim for a darker stummel to blend with the darker hues of the stem. If this succeeds, then I’m hoping the reds of the Cumberland stem ‘pop’ more instead of competing with the stummel. We’ll see! I can use alcohol-dipped cotton pads to lighten the stain after application if I choose. After setting the stummel up on the cork/candle stand I apply the stain undiluted with a cotton swab to see how it goes. I liberally allow stain to move over the inverted stummel – making sure of coverage over the inverted rim. After a good covering I use a lighter to fire the stain which is a quick-combustion of the alcohol leaving the stain to set well into the grain. The Italian stain ‘fired’ as hoped! I repeated the procedure and then used the alcohol dipped pads to clean off the burn layer of the stain revealing how the grain received the stain – it’s never the same! I take a picture to do a quick compare of stummel and stem. After comparing I’m thinking that I like the dark hue but it needs some reds so I decide to add a layer of Cheren stain – red which I will mix with alcohol as it is a water based stain. In my mind I’m thinking of the ‘Ox Blood’ depth that Steve uses – which is not found in Bulgaria! I think the addition of the red stain does the trick (last picture) though it’s difficult to see the difference comparing the last two pictures. Next, I apply several layers of carnauba wax to the stummel and stem with Dremel and cotton wheels. I’m careful to keep the Dremel wheel moving in rotation over the wood and use the lowest speed so not to overheat the wood. The buffing brings out the grain and the luster of the Cumberland stem. I continue the buffing with a clean cotton wheel over the entire stummel and stem surface. I finished with a thorough vigorous buffing with microfiber cloth to bring out the grain depth while watching Germany and Italy’s World Cup match. The recommissioning of this Butz-Choquin Rocamar was more of a project than I was expecting. I prefer the finish now before me to the shiny finish I started with. I like the new color scheme for the bowl and Cumberland stem – I believe it works well. The reds in the Cumberland stem match the grain amazingly well and the grain swirl in the rim has the appearance of continuing in the stem – a neat effect. I’m very pleased with the color blends. Another project done with new things learned to draw upon for the next candidate brought back to life! Thanks for joining me!

I thought this one would be easy – boy was I wrong

3 Replies

Blog by Steve Laug

I wanted a bit of a breather so I went through my box of pipes for repair and picked this multi-finish Jobey Asti Classic Bent Billiard to clean up. The stamping on the left side reads Jobey Asti Classic and on the right side France and the shape number 470. At first glance it looked like it would be a simple restore and clean. The bowl looked decent in the box and the stem was okay as well. When I got back to the table and did a closer examination I was surprised by what I saw. The bowl rim was in bad shape with the outer edge knocked and damaged. There were dent and score marks in the top of the rim. The lava had flown over the top and it looked as if someone had thrown a coat of Urethane on top of the bowl, grime and all. I looked at the exterior and found that even the grooves in the rusticated bottom of the bowl were thickly coated with the plastic stuff. The stem looked good at first but as I examined it I found that it had been cut off and the button recut and a slot fashioned that was not clean or even. The surface of the stem on the top and bottom next to the button was heavily built up with what appeared to be black epoxy and it was bubbled and full of pin prick like holes. It also was not bent correctly to the shape of the bowl. Truly it would need a lot more work than originally thought. (As an aside don’t use Urethane on bowls it is a bear to clean off and if you have to at least clean them before you dip them in that awful plastic stuff.) I took the pipe apart and unscrewed the Jobey Link from the bowl and took a picture of the parts. I wanted to see how dirty the internals were and if the Link would come out easily. For those of you who don’t know the Link system one of the nice perks is that the end of the tenon that sits in the stem are slotted so you can insert a slot or blade screwdriver to loosen and remove the Link. It is a great piece of forethought on the part of the designer.Because of the coat of Urethane over the lava I needed to top the bowl to remove the grime and also to clean up the outer edges of the bowl. I topped it with 220 grit sandpaper on my topping board.I sanded the finish on the smooth portion of the bowl with a medium grit sanding block and then wiped the bowl down with acetone to try to break the plastic finish. I was partially successful in removing it but more work would need to be done.I reamed the bowl with the PipNet reamer and also with the Savinelli Pipe Knife to remove the remnants of cake that still were deep in the bowl. I reamed it back to bare briar so that the new owner could build a cake of their own choosing. You can also see the top and outer edge of the rim in these photos that show it after the topping of the bowl.In the next photo you can see the film of the plastic stuff still on the bowl with the scratches from the sanding block visible. I decided to let it soak in the alcohol bath for a day and a half to see if the finish would break down some more now that it had been broken through with the sanding blocks.When I took it out of the bath the finish was pretty smooth. The plastic stuff was gone. I sanded the bowl and shank with micromesh sanding pads to remove some of the scratching and was careful around the stamping on the sides of the shank. I washed the bowl down with some acetone on cotton pads and then stained it with a dark brown aniline stain. I flamed it and repeated the process to make sure I got and even coverage.While the bowl dried I turned to work on the stem. I heated it with the heat gun to soften the Lucite enough that I could bend it to the proper angle. It did not take too much to get the angle correct but the heat caused the epoxy patch to bubble. The perk of that was that the airhole pin prick marks disappeared.I wiped the bowl down with alcohol on cotton pads to remove some of the dark stain and bring the grain to the forefront.I cleaned out the interior of the stem with cotton swabs, pipe cleaners and alcohol. I cleaned out the area where the Jobey Link sat in the stem and the airway to ensure good fit and draw.Now it was time to work on repairing the stem repairs! The next photos show what the patches looked like when I started. They stood out clearly and the heat of the gun made them raise and bubble. To me they looked like overkill in terms of a repair. It was almost if the person who did the patch was trying to build up the thickness of the stem at the button to give it strength. It would take some work to make it blend in. I sanded the surface of the stem with 220 grit sandpaper to smooth things out and try to match the stem surface. Of course I forgot to take photos of the process but the ones shown below with the micromesh sanding pads will show the change. The third photo below shows the slot in the button. I worked on it with needle files to clean it up and shape it and again forgot to take photos of the process.I rubbed the bowl down with some Conservator’s Wax so that when I cleaned out the shank and Jobey Link System with would not damage the finish that I had done. (I know I should have done this before staining but this one irritated me and I forgot to do so.) I cleaned the link and then put a little Vaseline on the threads and turned it into the mortise. I adjusted it with the screwdriver to set it into the shank. I buffed the bowl lightly with Blue Diamond on the wheel and gave it a light coat of olive oil. I took the following photos to show what the pipe looked like at this point in the process. You can also see the state of the stem in these photos. Overall the pipe is looking pretty good at this point. It is far better than I expected when I started. The contrast of the dark stain on the rustication and the lighter stain on the smooth briar makes this pipe look quite “classic” matching its name. I wet sanded the stem with 1500-2400 grit micromesh sanding pads and dry sanded with 3200-4000 grit pads. I finished sanding with 6000-12000 grit pads. I buffed the bowl and stem with Blue Diamond. I avoided the rusticated portion so as not to get polishing compound in the crevices and pits of bottom half of the bowl. I waxed the bowl and the stem with multiple coats of carnauba. The finished pipe is shown in the photos below. The grain is quite beautiful and the contrast between the smooth and the rusticated portions gives a unique look to the pipe. Thanks for looking.

An Interesting Churchill’s Volcano Brought to Life

1 Reply

Blog by Steve Laug

The next out of the box of pipes from my brother is the one below. It is stamped Churchill’s on the smooth underside of the shank. The shape number 882 is along the shank stem junction on the underside. I have refurbished several Churchill’s pipes from their pipe shop in Norwich. I wrote a bit about that shop when I did a refurbish on a Churchill’s Bent Pot. The link to that article is as follows: https://rebornpipes.com/2013/09/08/churchills-bent-pot/. This pipe had a rustication that is very similar to those I have seen on Lorenzo pipes. The stem on this pipe is stamped Italy on the underside. The finish was tired and dirty but the rustication was in good shape. The rim was solid with no damage to the inner or outer edge but it was thick with tars. The bowl was reamed while I was visiting in Idaho. The stem was in good shape at first glance. It was oxidized but there were no tooth marks. As I examined it I found that the stem had been cut off and a new button was cut into the surface. The slot was also reshaped. The button itself was very thin as the stem was also thin at this point. I took a close up photo of the rim and the stamping on the underside of the bowl. The rim is dirty but the rustication is in good shape with no burn marks or damage. The stamping is also very clear.I scrubbed the rim with a brass bristle wire brush to remove the tars and oils that had built up there. Once it was loosened I scrubbed it with a tooth brush and Murphy’s Oil Soap to clean off the grime in the finish. I rinsed the bowl with warm running water to remove the grime and soap. The next photos show the cleaned finish on the pipe. I used the dental spatula to scrape out the inside of the shank and break the tars and oil build-up away from the walls of the shank and mortise. I cleaned out the mortise and airway in the shank and stem with pipe cleaners, cotton swabs and alcohol. I sanded the stem with 220 grit sandpaper to remove the oxidation. I built up the button with black super glue to add thickness and enable a grip on the button. I used a file to shape the button and recut the sharp edge against the stem surface. I sanded it with 180 grit sandpaper to smooth out the areas in front of the button on the top and the bottom sides. I continued to shape the stem surface and the button with 220 grit sandpaper and also used the needle files to open up the slot in the button and reshape that.I sanded the stem with 220 grit sandpaper to clean off the oxidation. I wet sanded the stem with 1500-2400 grit micromesh sanding pads. I rubbed it down with Obsidian Oil. I dry sanded the stem with 3200-4000 grit sanding pads and gave it another coat of oil. I finished sanding the stem with 6000-12000 grit pads and gave it a final coat of Obsidian Oil. I let the stem dry. I stained the bowl with a dark brown aniline stain and flamed it. I repeated the process until the coverage was good. I hand buffed the bowl with a shoe brush. I gave it a light coat of olive oil and hand buffed it again. I rubbed the surface down with some Conservator’s Wax and then hand buffed it with the shoe brush for a final shine. I buffed the pipe lightly with Blue Diamond polish on the wheel and then gave the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad and then hand buffed it with a microfibre cloth. The finished pipe is shown in the photos below. The rustication has depth and textures both visually and tactilely. It feels great in the hand. The shape of the bowl and the faux military stem give the pipe a classic look with a flair that is almost Danish looking. I like the finished look of this one. Thanks for looking.

Restoring a Comoy’s The Guildhall Twin Bore Long Shank

4 Replies

Blog by Steve Laug

The next pipe I brought to my table to work on was stamped on the left side of the shank The Guildhall over London Made and on the right side Twin Bore over Made in England. The stamping was readable with a light and a magnifier but it was faint. It was a nicely shaped long shank billiard or some would call it a Lumberman. I have worked on many Comoy’s The Guildhall pipes but never have seen one stamped like this. The stem indeed is a twin bore. It was in decent shape but it did not bear testimony to the point of the twin bore “bite proof” stem. It had a lot of tooth marks and chatter on the top and the bottom side of the stem. The tooth marks were quite deep but did not enter the airway in the stem. So I guess in that way the stem was “bite through proof”. The finish was quite nice. The pipe was in good shape with just some grime on the surface of the briar. The rim had been topped and restained sometime in its history as the stain is quite a bit lighter than the rest of the pipe. The outer and inner edges of the rim were darker than the surface of the rim. The bowl had been reamed but the cake was left uneven on the walls of the bowl. I took a close-up photo of the rim to show the previous topping and the darkening of the inner and out edges. You can see that it had been touched up and the rim edges not cleaned up. I also took some close-up photos of the damage to the stem in terms of tooth marks and chatter. I sanded the top and bottom sides of the stem to remove the tooth chatter on the surface and to clean up the area around the deeper tooth marks. I wiped the areas down with alcohol and then used black super glue to fill in the deep marks.While the stem repairs were drying I reamed the bowl with the Savinelli Pipe Knife. I took the cake back to bare briar.I used a folded piece of 220 grit sandpaper to clean up the bevel on the inner edge of the bowl. I worked slowly to make sure that the bevel maintained the roundness of the bowl. Once I had it finished I stained the rim and inner edge with a medium brown stain pen to match the colour with the rest of the pipe.I used a dental spatula to scrape out the inside of the mortise as there was a ridge of tar and oil part way down the shank. I scraped out the grime and then scrubbed the inside of the mortise and the airway in the shank with pipe cleaners, cotton swabs and alcohol until it was clean.By the time I worked on the twin bore stem the repairs were dry. I lightly sanded them and then cleaned out the twin bore airways.I sanded the repairs on the stem with 220 grit sandpaper until the surface of the repairs was blended into the surface of the stem.I wet sanded the stem with 1500-2400 grit micromesh sanding pads. I rubbed down the stem with Obsidian Oil. I dry sanded it with 3200-4000 grit pads and gave it another coat of oil. I sanded it with the last set of three micromesh sanding pads – 6000-12000 grit pads. I gave it a final coat of Obsidian Oil and set it aside to dry. I buffed the pipe with Blue Diamond and worked over the scratches that still showed up on the top surface of the stem. It did not take much to remove them and get a deep shine on the stem. I buffed the bowl as well, being careful around the stampings on the shank of the pipe. I gave the bowl and stem multiple coats of carnauba wax and buffed it with a clean buffing pad to raise the shine on the briar and vulcanite. The finished pipe is shown in the photos below. It shines and has depth to the finish. The stamping is faint but is my only example of a Twin Bore Comoy’s The Guildhall Pipe. It is a beauty in my opinion. Thanks for looking.

An Interesting Antique Store Stummel

3 Replies

Blog by Steve Laug

I have a routine when I visit in Bellingham. I take the ladies in my life to the mall and leave them to shop and I set out on my circuit of pipe haunts to see if I can find some likely object of my attention to repair. I rarely come home empty handed, though I don’t know if that is because I will work on many kinds of pipes or if it is because I generally find something. It may be hard for the observer to discern the difference, I know it is for my wife and daughters. I visited several of my haunts and finally in the last one I did a quick walk through and found nothing… this time it looked like I would come home empty handed. Just to make sure I asked at the counter if there were any old pipes in the shop. The seller pointed directly behind me and there in a case that I had totally missed were four pipes. I bought them all. They had a look of age about them so I jumped and paid the price. It turned out that one of them had a cracked bowl but I was able to cannibalize a sterling silver band for an old KBB Yello Bole from the 20s. Two of them were also older – one a GBD and one a Dr. Plumb. The fourth, a Canadian had a gold coloured band and was missing the stem. It looked pretty dirty and the finish was gone. I figured that it too might be one I cannibalized for parts. I paid for them and went out to my car. I went through them and looked them over. The first three showed no surprises. But the stemless bowl was a real surprise. There on the shank was the arced Barlings stamping and under that was the stamping Ye Olde Wood over 237 on the left top side of the shank and Made in England on the right top side. There is also a remnant of the word EXEL. Boy was I surprised. Suddenly it went from a potential victim for cannibalization to one that had some interest for me. It turned out to be the best of the lot. I took a close-up photo of the rim to show the extent of the damage to that area. The cake in the bowl had flown over the top of the rim. There were also dings and dents that were quite deep. The outer edge was compromised and rounded over and the inner edge was out of round. I also included a photo of the stamping and the crack in the shank. This is the stamping that I saw in the bright daylight when I left the basement antique shop.I went through my can of stems and found one that would work on this shank. I had to go with a bit of an oversized stem in terms of diameter as the shank was thinner on the top than on the bottom. I would have to hand fit the stem to accommodate that idiosyncrasy.I used a microdrill bit to put a tiny pin hole at the end of the crack and then filled in the crack with super glue. The drilled hole would keep the crack from spreading and the glue would fill it in. The integrity of the shank was stabilized by the band as well.Once I had a good fit of the stem to the shank I used the Dremel and sanding drum to remove the excess vulcanite on the diameter of the stem. The fine tuning and flow of the stem would be done by files and hand sanding. I reamed the bowl with the PipNet reamer and took out the majority of the cake. I cleaned it up and took it back to briar with the Savinelli Pipe Knife. I topped the bowl on a topping board using 220 grit sandpaper. I removed the damaged surface of the rim until the outer edges were sharp and there was no rounding.I scrubbed the exterior of the bowl with acetone on cotton pads to remove the grime and wax that had built up and made the exterior dull and lifeless. I reworked the inner edge of the bowl to bevel it and bring it back to round using a folded piece of 180 grit sandpaper and then a piece of 220 grit sandpaper.I wiped the bowl down again with acetone to remove any remaining grit and also the sanding dust from the rim repairs.I put the stem in place and took some photos to be able to see what still remained to remove from the diameter of the stem and what shaping still needed to be done. There was some width to be removed from the top and bottom sides at the band and then the taper needed to be reduced as well to remove the slight hip. The width on the right and left side also needed a bit more work to make the flow seamless. I sanded the stem with 180 grit sandpaper to further shape it and clean up the flow from the shank to the button. It took a lot of sanding to get the angles and flow just right.I scrubbed out the mortise and the airway in the stem and the shank with alcohol, cotton swabs and pipe cleaners.I sanded the rim with a medium and a fine grit sanding sponge to remove the scratches left behind by the topping and then stained it with a light brown stain pen to match the colour of the bowl.I wet sanded the stem with 1500-2400 grit micromesh sanding pads and gave it a coat of Obsidian Oil. I dry sanded with 3200-4000 grit pads and gave it another coat of oil. I finished the sanding with 6000-12000 grit pads and gave it a final coat of oil. I set it aside to dry. I buffed the pipe with Blue Diamond and gave it multiple coats of carnauba wax. The colour darkened slightly with the wax. I buffed it with a clean buffing pad and then by hand with a microfibre cloth. The finished pipe is shown below. I am pleased with the way the fit and finish of the stem came out and also the overall look of the pipe. Thanks for looking.

A Surprise While Cleaning up a Primus 2 Bent Billiard

2 Replies

Blog by Steve Laug

When I decided to clean up the third of the four pipes I picked up on a recent trip to Sofia, Bulgaria I was surprised by what I ended up finding. From the moment I saw it on the marker seller’s table it was a bit of a mystery to me. I picked it up and checked it out quickly under the scrutiny of the seller who did not know what to do with this English speaking Canadian. I paid him for it thinking that it was an alternative wood. But even then I was not certain about it. I was drawn to the colour of the bowl and the simple elegance of the pipe. When I examined it in the market I opened the lid of wind cap and saw appeared to be white spots on the bottom third of the bowl. I was not sure what it was. I was almost convinced it was mold or something like that which I would need to remove. The silver wind cap was in great shape with a little wear but still aligned to the silver rim cap. It was probably nickel though I am not certain. The stem was bent correctly but it just did not look right. When I removed the stem from the shank the inside of the shank was also lighter in colour.

When I got home from Sofia and brought the pipe to the work table I examined it much more closely. I looked at it with a lens to see if the white was mold or something like that but it did not appear to be that. I rubbed the bowl with my finger to try to remove it and nothing happened. It did not come off on my finger. The upper portion of the bowl was darkened and had a light cake. The bottom of the bowl itself was white. There was no mold or powder on the surface. The more I looked at it the more I am convinced that what I had found was a meerschaum pipe rather than a wooden one. That was a surprise because when I picked it up I was pretty certain on cursory examination that it was a hard wood bowl. It was very lightweight and it did not seem to have any grain. The golden colour of the material also made me think of other older meerschaum pipes that I have restored. At this point I was pretty convinced that I was dealing with an older meerschaum pipe. What a surprise for a pipe I purchased for about $5 CNDN.

I continued to examine the pipe once I had decided it was meerschaum. The metal wind cap was tarnished and undamaged on the outside but the inside of the cap was oxidized and rough. The cap on the rim was also tarnished and rough with tars. There were two nail heads that held the cap on the rim. The meerschaum itself was in excellent shape. There were no dents or gouges in the bowl or shank. There was a slight indentation or ring around the end of the shank that told me that a metal band that had originally been present. The left side of the shank was stamped PRIMUS over 2. The stem was obviously one that seller had taken out of his bag of bowls and stems and put together. It fit in terms of tenon diameter which was good because most of the pipes on his table had cracked shanks from his matching game. The stem diameter was close but I noticed that the mortise was not centered in the shank. Due to that the bottom of the stem sat below the bottom of the shank while the top of the stem was slightly lower than the shank. The stem was lightly oxidized and had some tooth chatter.

The next four photos show the pipe as it was when I brought it to the table. I reamed the bowl with a Savinelli Pipe Knife so that I could carefully cut back the cake to check on the material the bowl was made of. I did not want to damage it so I went slowly and carefully.I wiped down the exterior of the bowl with a damp cloth and removed the stickiness and dirt on the surface. I also pressed a WDC band on the shank. It had a small split that I repaired with super glue but it was the only one I had that fit the shank and did not cover up the stamping. It will have to do. I used some silver polish to scrub the rim and the windcap. I cleaned out the mortise and airway on the shank and stem with pipe cleaners, cotton swabs and alcohol until they were clean. To adjust the diameter of the stem to match the rolled over end cap I sanded it with 220 grit sandpaper. I wanted the diameter of the stem to show equally from the end view so that the same amount of silver showed on each side.I wet sanded the stem with 1500-2400 grit micromesh pads and gave the stem a coat of Obsidian Oil. I dry sanded it with 3200-4000 grit pads and gave it another coat of oil. I sanded it with the final three grits of micromesh pads – 6000-12000 and gave it a final coat of Obsidian Oil. I set it aside to dry. I buffed the bowl and stem with Blue Diamond and gave them both several coats of carnauba wax. I buffed it with a clean buffing pad to give it a shine and then hand buffed it with a microfiber cloth to deepen the shine. The finished pipe is shown in the photos below. If I come across another band someday I will swap them out but this works for now. Thanks for looking.