Monthly Archives: March 2022

Stepping Up with a Pilot S455 French Made Mini-Churchwarden

Leave a reply

Blog by Steve Laug

The next pipe on the table is an interesting mystery pipe that is stamped France on the underside of the shank and on the left side reads PILOT. On the right side is a shape number S455 near the bowl shank union. We picked the pipe up from EBay on December, 2016 and it came from Port Perry, Ontario,  Canada. It is an interesting piece of briar with a long vulcanite stem. The shape is a variation on a Rhodesian without the rings around the cap. The finish was dirty and dull with grime ground into the briar around the bowl and shank. The bowl has a moderate cake in the bowl and a light coat of lava on the rim top and inner edge. There is some darkening on the inner edge of the bowl. The stem was oxidized and had tooth chatter on the top and the underside near the button. Jeff took photos of the pipe before he started his cleanup work. He took some photos of the bowl to give a sense of the condition of the bowl and rim top. You can see the cake in the bowl and the lava on the rim top. There is also some damage and darkening to the inner edges. The stem is clean but shows light oxidation and tooth marks on both sides near the button. He took photos of the bowl sides and heel to show the grain around the bowl. It really was a nice piece of briar. Jeff took photos of the stamping on the shank sides. It is clear and readable as noted above. Jeff had done a great job cleaning up the pipe as usual. He reamed the pipe with a PipNet reamer and cut back the cake back to the bare briar. He cleaned up the walls with a Savinelli Fitsall Pipe Knife. He scrubbed the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol to remove the tars and oils. He scrubbed the exterior of the pipe with Murphy’s Oil Soap and a tooth brush to remove the grime from the finish. He worked on the rim top lava and darkening with the soap and tooth brush. He scrubbed the inside of the stem with alcohol and pipe cleaners. He scrubbed the exterior with Soft Scrub and then soaked it in Before & After Deoxidizer. He washed it off with warm water to remove the deoxidizer. The pipe looked far better when it arrived.    I took some close up photos of the rim top and also of the stem surface. I wanted to show how well it had cleaned up. The rim top photo looks very good but you can see the damage to the inner edge around the bowl. I also took close up photos of the stem to show the light tooth marks and scratching on the surface near the button.    I took photos of the stamping on the left and right side of the shank. You can see that it is stamped as noted above. It is clear and readable. I took the pipe apart and took a photo of the pipe. It is a good looking pipe and has some great looking grain around the bowl and shank.I worked on the damage around inner edge of the bowl with a folded piece of 220 grit sandpaper. I was able to smooth it out and clean up the damage.I wiped the bowl down with isopropyl alcohol to remove the uneven stain and even out the finish on the bowl. I was able to remove just enough to make the grain really stand out. I polished the briar bowl and shank with micromesh sanding pads. I dry sanded it with 1500-12000 grit pads and wiped it down with a damp cloth after each pad.     I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned my attention to the stem. I sanded out some tooth marks on the stem surface with 220 grit sandpaper. I started the polishing with 400 grit wet dry sandpaper. I wiped it down with some Obsidian Oil.   I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I gave it a final rub down with Obsidian Oil and let it dry. I am excited to finish this French Made Pilot S455 French Made Mini Churchwarden. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with a microfibre cloth to deepen the shine. It is fun to see what the polished bowl looks like with the polished nickel band and the black vulcanite stem. This Classic looking Pilot S455 Mini Churchwarden feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 7 ½ inches, Height: 1 ¼ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 25grams/.88oz. It is a beautiful pipe and one that will be on the French Pipe Makers section of the rebornpipes store soon. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.

Rebirthing a Lovely Peterson’s Of Dublin Aran 999 Rhodesian

Leave a reply

Blog by Steve Laug

The next pipe I have chosen is a smooth Peterson’s Rhodesian. I am not sure where it came from or when we might have picked it up. This Rhodesian came with a nice nickel band on the shank end that was factory fitted to the stamping on the shank. The grime was ground into the finish on the bowl sides. The contrast of the brown stains gave the grain a sense of depth. It was stamped on the left side of the shank and read Peterson’s [over] of Dublin [over] Aran. The right side had the shape number 999 stamped mid shank. The nickel band was stamped Peterson [over] a stylized P [over] Of Dublin. There was a moderate cake in the bowl and an overflow of lava on the rim top. The stem was oxidized, calcified and had light tooth marks, chatter on the top and underside on and near the button. I took photos of the pipe before I started my cleanup work. They tell the story and give a glimpse of the promise that we see in this pipe. I took photos of the rim top and stem to show the general condition of the pipe. The bowl is moderately caked and the rim top and back edges have a thick lava overflow. The photos of the stem show that it was oxidized, calcified and has light tooth marks on the top and underside near the button.   I took a photo of the stamping on the left side of the shank and the band. It is clear and readable and reads as noted above. I did not take a photo of the 999 stamp on the right side. The photo of the band shows how it was stamped on the nickel – centered and clean. There was some oxidation and sticky substance on the underside of the band next to the shank. I took the stem off the shank and took a photo of the look of the pipe to show the relation of the size of the parts. It is a nice looking pipe. I turned to “The Peterson Pipe” by Mark Irwin and Gary Malmberg to get some background on the Aran line. On page 294 it had the following information.

Aran (1965-) First issue of line described as “handhewn” (rusticated) with black semi-matte finish, in P-lip and fishtail mouthpiece. Second issue 1975, red sandblast, XL shapes. Third issue circa ’97, gold hot-foil P stamped on the mouthpiece, brown semi-matte smooth finish, no band. Fourth issue after 2010, with nickel band, no P stamped on the mouthpiece. Mounted and unmounted versions are available concurrently.

I knew that I was dealing with an Aran from the Fourth Issue of the Aran line that came out after 2010 because of the nickel band and unstamped stem. As such it was a newer pipe. Now it was time to work on the pipe. (Applicable information noted in red above.)

I started my work on the pipe by reaming it with a PipNet reamer and cut back the cake back to the bare briar. I cleaned up the walls with a Savinelli Fitsall Pipe Knife. I sanded the bowl walls with 220 grit sandpaper wrapped around a piece of dowel. I scrubbed the exterior of the pipe with Murphy’s Oil Soap and a tooth brush to remove the grime from the finish. I worked on the rim top lava and darkening with the soap and tooth brush. I used a shank brush to clean out the inside. I rinsed the pipe with warm water and dried it off. I scraped out the inside of the shank with a dental spatula to remove the thick build up of tars and oils. Once I had removed that I scrubbed the inside of  the shank with alcohol, cotton swabs and pipe cleaners. I cleaned the airway in the stem at the same time. I cleaned up the darkening on the rim top and the inner edge with a folded piece of 220 grit sandpaper until it was clean and undamaged.  I polished the briar bowl and shank with micromesh sanding pads. I dry sanded it with 1500-12000 grit pads and wiped it down with a damp cloth after each pad.    I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process.   I polished the nickel band with a jeweler’s cloth to remove the tarnish and oxidation as well as add some protection to the band.    I set the bowl aside and turned my attention to the stem. I scrubbed it with Soft Scrub all purpose cleaner to remove the oxidation and calcification on the stem surface. I was beginning to look better.    I “painted” the surface of the stem with the flame of a Bic lighter to lift the tooth marks on the surface. I was able to lift them all to the point that sanding would remove the rest of them.     The button was worn on the top side and on the end so I built it up with black super glue. I filled in the tooth marks on the top and on the end and set it aside to cure.     I reshaped the button surface and end and sanded out some tooth marks on the underside of the stem with 220 grit sandpaper. I started the polishing the stem with 400 grit wet dry sandpaper. I wiped it down with some Obsidian Oil.  I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine.   I am excited to finish this Peterson’s Of Dublin Aran 999 Rhodesian. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl amd stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with a microfibre cloth to deepen the shine. It is fun to see what the polished bowl looks like with the polished nickel band and the black vulcanite stem. This Classic looking Peterson’s Aran Rhodesian is one of my favourite shapes and it feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ¾ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 51grams/1.80oz. It is a beautiful pipe and one that will be on the Irish Pipe Makers section of the rebornpipes store soon. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.

Restoring a Millennium of Tynwald Black, Faceted Meerschaum Bent Billiard

Leave a reply

Blog by Steve Laug

The next pipe I have chosen to work on is an interesting faceted Black coloured Meerschaum Bent Billiard. It is a pipe that we found somewhere along the journey but have no record of when or where we picked it up. It is a classic Manx style African Meerschaum pipe. It was stamped on the ferrule on the shank end had had the Manx running legs logo and read Millennium [arched over] Of Tynwald in a circle around the . It was in great condition when I brought it to the table. There was a heavy cake in the bowl and some lava on the rim top and edges of the bowl. The brass coloured ferrule was in good shape but had scratches that would need to be polished. The stem had the same running legs logo on the top of the saddle. There was some oxidation and calcification on the stem surfaces as well as light chatter and tooth marks near the button on both sides. I took photos of the pipe before I started my work. I took photos of the rim top and stem to show the general condition of the pipe. The bowl is heavily caked and the rim top and edges have a thick lava overflow. The stem is oxidized, calcified and has tooth marks on the top and underside near the button.  I took photos of the stamping on the left side of the brass ferrule. It reads as noted above. I also captured the stamping on the stem to show the running legs logo there as well. I removed the stem and took a photo of the pipe to have a look at the parts and overall look. I did a quick search on Google to see what I could learn about the Millennium Of Tynwald brand. The first link I found was for one that was on Worthpoint that had a fascinating description of the brand (https://www.worthpoint.com/worthopedia/meerschaum-pipe-manx-millennium-1979-464084331). I include a portion of that quote below.

Manx Tynwald Millennium Meerschaums Pipe. The pipe will probably date from 1979 the year of the Millennium. Made in the Isle of Man by J Laxey & Co. Meerschaum production ceased in 2002. From the 1960’s they produced bowls for Barlings and Petersons among others.

I am not sure how the year 1979 is linked to the Millennium but somehow the write above associates that and dates his pipe. I am not clear about the dates of the pipe. I know that it was made prior to 2002 when the Laxey Factory closed.

I turned then to Pipephil and did a quick search there for information linking the Millennium brand stamp with Manx (http://www.pipephil.eu/logos/en/nonbriar/meer.html). Sure enough the link was there. I have included a screen capture of a pipe with the same ferrule and stem stamp as the one that I am working on. I also included a note from the sidebar.Laxey Pipe Factory (closed in 2002). Other brands from the factory: “Manxpipe”, “Manxman”, “Manxland”. See also: Man Pipes

I turned to Pipedia to have a read about the history of the Laxey Pipe Company on the Isle of Man (https://pipedia.org/wiki/Laxey_Pipes_Ltd.). There was a short history of the brand that I included below.

Laxey Pipes Ltd. resided in a historical 19th century four-storey Man stone building at The Quay, Old Laxey, Isle of Man, which thankfully has been preserved.

The company specialised in the production of meerschaum pipes using the Meerschaum mined by the Tanganyika Meerschaum Corporation in the Amboseli basin in Tanganyika (since 1964 part of the United Republic of Tanzania).

Please note: you may often find names like “Manx Pipes Ltd.”, “Man Pipe Co.” and others more, but there is no indication of another Isle of Man pipe producer other than Laxey Pipe Ltd. at any time!

 Laxey Pipes Ltd. marketed own brands like “Manxpipe”, “Manxman”, “Manxland” e.c. Names like “John Bull”, “White Knight” (unwaxed), “Domino” (black, or lined) indicated some shapes / colours of Laxey’s own series. The stems either showed the astronomical sign for “male” or “man” (circle + arrow), or the crest of the Isle of Man, the 3-legged X in a circle. Manxpipes and Laxey’s other brands were available through pipe retailers in general, but also were sold (mainly) to tourists through their own shop in Laxey.

Furthermore Laxey Pipes Ltd. manufactured the meer bowls for Peterson, Barling, Nørding and others from the later 1960’s until 2001. Man Pipe e.g. was a brand distributed by Comoy’s. The bowls usually showed no nomenclature indicating the orderer. “Genuine Block Meerschaum” was engraved frequently. Often, just the stems were different, while bowls were the same.

Supply of meerschaum from East Africa ran out (Kenya / Tanzania exhausted, Somalia inaccessible), and thus the last Laxey meers were supplied to trade in May, 2001. Laxey Pipes Ltd. tried to survive continuing with briar pipes – mainly in the Danish style -, but to no success. It closed down business in July, 2002.

ADDENDUM 
After publishing this blog I received a response on Facebook about the stamp on the ferrule and more information about the brand and logo. I quote from Adrian Sacco

The millennium referred to is the 1000th anniversary of Tynwald, the Isle of Man parliament. It’s the oldest/longest continuous government in the western world. The Isle of Man is a self-governing British crown dependency located between Great Britain and Ireland. It is not part of the UK…  Just to add, the famous “three legs” is the symbol of the Isle of Man. It’s called a triskelion. The Manx motto is “quocumque jeceris stabit “ which translates “whichever way you throw me I stand”. This reflects the resilience often found in small island nations.

Thanks Adrian for the added information on the pipe. Very helpful.

Armed with that information, I started my clean up of the pipe by reaming it with a PipNet reamer and cut back the cake back to the bowl walls. I further cleaned up the walls with a Savinelli Fitsall Pipe Knife. I finished the cleaning of the bowl with a piece of dowel wrapped in 220 grit sandpaper. I smoothed out the bowl walls and checked for cracks and flaws. All looked very good. I cleaned off the build up in the rim top with the edge of the Savinelli Fitsall knife and scrubbed it with cotton pads to remove the residual grime. I looked better but there was more work to do. I scrubbed the interior of the bowl, shank and stem with pipe cleaners, cotton swabs and alcohol to remove the tars and oils. It was full of tars and oils that with a bit of work came clean. I worked some Before & After Restoration Balm into the surface of the bowl with my fingertips to clean, enliven and protect the finish. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. You can see the interesting carved lines on each of the facets of the bowl. It adds an almost primitive touch to the bowl.      I polished the nickel ferrule with micromesh sanding pads with a jewelers cloth to remove the oxidation and give it a shine.   I set the bowl aside and turned my attention to the stem. I scrubbed it with Soft Scrub cleanser to remove the oxidation and light calcification. It took a lot of oxidation off the stem as can be seen in the photos.   I sanded the light tooth marks and chatter out of the surface and removed the remaining oxidation with 220 grit sandpaper. I started the polishing of the stem with 400 grit wet dry sandpaper.   I touched up the running legs logo with white acrylic fingernail polish. Once it cured I scraped it off and polished it with a worn 1500 grit micromesh pad. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil.  I am excited to finish this Laxey Pipes Millennium Of Tynwald Black Faceted Meerschaum. I put the pipe back together and buffed it lightly with Blue Diamond on the buffing wheel. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to deepen the shine. I hand buffed the pipe with a microfiber cloth to further raise the shine. It is fun to see what the polished bowl looks like with etched facets all around it. Added to that the brass coloured ferrule and the polished black vulcanite stem and you have a beautiful pipe. This Millenium Of Tynwald Meerschaum is great looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 51 grams/1.80 oz. It is a beautiful pipe and one that I will be adding the British Pipe Makers section of the rebornpipes store. I you are interested in adding it to your collection please let me know. Thanks for walking through the restoration with me as I worked over this pipe and for reading this blog.

A Decorated Veteran

Leave a reply

Blog by Kenneth Lieblich

Next on the chopping block is this superb Ropp Six. It comes from a group of pipes I purchased from France. I love this pipe. I have a particular interest in French pipes and pipeworks, and I grabbed this one to restore for my collection. This is an old, old pipe with a few wounds (i.e. a veteran pipe with decorations) and needs just a little help to come back to life. This pipe was made by the venerable French pipe company, Ropp. Ropp has been around for a long time and their early pipes are really quite wonderful (the less said about their modern pipes, the better). The markings on the left-hand side of the shank read Ropp [over] Six. The right-hand side of the shank reads 886, presumably the shape number. Also, on the stem, there is the Ropp logo: Ropp, encircled in an oval.This pipe shape is a Rhodesian – a variation of the classic Bulldog. A Rhodesian will have a cylindrical shaped shank, not a diamond shank like the Bulldog. This is a really pretty pipe and feels very comfortable in the hand.

From Pipedia, here is a very brief history of the Ropp company:

Eugène-Léon Ropp (1830–1907) acquired a patent for the cherrywood pipe in 1869. In 1870, he established a workshop to manufacture such pipes in Bussang, in the Vosges mountains. Around 1893, his business moved into the former mill of Sicard (part of the community of Baume-les-Dames in Upper Burgundy. The pipes were a big success in export as well. Shortly before 1914, Ropp designated A. Frankau & Co. (BBB) to be the exclusive distributor in the UK and its colonies. Probably in 1917, a workshop in Saint-Claude in the rue du Plan du Moulin was acquired to start the fabrication of briar pipes. In 1923, another small building in Saint-Claude, serving as a workshop for polishing, was added. Cherrywood pipes were the mainstay of Ropp until the company finally closed down in September 1991. The company was taken over by Cuty-Fort Entreprises in 1994. On to the pipe: it was in decent shape, but it had a few issues. The stem had a bit of oxidation and calcification, but – mostly notably – it had substantial bite marks, top and bottom. The stummel also had a few issues. The outside of the bowl had some scratches and a couple of fills that needed to be addressed. These are the “decorations” I referred to in the title of this article. There was lava and debris on the rim, and a few burn marks too. The inside was pretty dirty too – it would need a thorough cleaning. The stem was first on my list. This stem has a stinger in it – and it was being quite stubborn about coming out of the tenon! I opted to warm the stem and stinger with my heat gun and this provided just enough softening of the internal goo to allow me to pull it out. The stinger then went for a soak in some lemon-infused isopropyl alcohol. I let it set for several hours and then cleaned it off and it looked much improved. I then finished it with some metal polish and moved on. I wiped down the outside of the stem with Murphy’s Oil Soap on some cotton pads. I also took a BIC lighter and ‘painted’ the stem with its flame in order to lift the bite marks and dents. This was not successful at all in raising the damage. More work would need to be done. Then, I cleaned out the insides with pipe cleaners and isopropyl alcohol. Even the bore was clogged with debris! It took an awful lot of work to get this clean! Once this process was done, the stem went for an overnight soak in the Pipe Stem Oxidation Remover. The following day, I cleaned all of the de-oxidizing mess off with alcohol, pipe cleaners, et cetera. The oxidation had migrated to the surface and would be fairly straightforward to remove. I scrubbed with SoftScrub on some cotton pads to remove the leftover oxidation. After this, I used some nail polish to restore the Ropp logo on the stem. I painted the area carefully and let it fully set before proceeding. I built up the dents on the stem with cyanoacrylate adhesive and let them fully cure. On this occasion, I actually built up several layers of the glue over a few days. I must admit, it was an annoying and frustrating process because, at this stage, it never looked quite right. I then sanded the adhesive down – first with a small file – then with 220-, 400-, and 600-grit sandpapers to meld seamlessly into the stem. I then used all nine Micromesh pads (1,500 through 12,000 grit) to bring out the lovely black lustre on the stem. I also used Obsidian Pipe Stem Oil in between each pad scrubbing. On to the stummel, and the usual cleaning procedures were in order for this pipe. This stummel was a bit of a mess inside, so I first decided to ream out the bowl. I used both the PipNet Reamer and the KleenReem to remove the built-up cake and followed that with 220-grit sandpaper to eliminate as much as I could. I took the bowl down to bare briar, as I wanted to ensure there were no hidden flaws in the walls of the bowl. There were some very thin craze lines inside the bowl, but they were small enough that I elected to leave them as they were. I then proceeded to clean out the insides of the shank with Q-tips, pipe cleaners, and isopropyl alcohol. There was considerable filth inside this stummel and it took a lot of cotton to get it clean. I followed that up by cleaning the insides with some dish soap and tube brushes.

I used a small butter knife to gently chip away at the lava on the rim. I then used more Murphy’s with a scrub brush to remove any remainder. This actually worked quite well. I then moved on to cleaning the outside of the stummel with Murphy’s Oil Soap and some cotton pads. That removed any latent dirt that blighted the wood.

In order to remove the remaining burns and nicks on the rim, I “topped” the pipe – that is to say, I gently and evenly sanded down the rim on a piece of 220-grit sandpaper. This effectively removed the damage, without altering the look of the pipe.Having completed that, I was able to address the small nicks on the stummel. I dug out my iron and a damp cloth to try and raise the nicks. The hot and moist steam can often cause the wood to swell slightly and return to shape. There was some movement – not a lot, but it was better than doing nothing. The repair was not perfect, but the remaining scratches would be improved by sanding.I lined the fills with cyanoacrylate adhesive and briar dust. After letting them cure, I sanded the fill repairs down with 200-, 400-, and 600-grit sandpaper. I then used all nine Micromesh pads (1,500 through 12,000 grit) on the stummel to finish it off. After that, a light application of Before & After Restoration Balm brought out the best in the stummel’s grain. There is some beautiful wood after all. It is a very handsome, decorated veteran. In order to accentuate the external beauty of this pipe, I opted for aniline dye. I applied some of Fiebing’s Medium Brown Leather Dye. As usual, I applied flame from a BIC lighter in order to set the colour. I then added a second coat – just to make sure. What a difference that made! It looked so much better with a fresh coat of stain. I applied some more Before & After Restoration Balm and then it was off for a trip to the buffer. A dose of White Diamond and a few coats of carnauba wax were just what this pipe needed. The lovely shine made the wood very attractive. This is a very handsome pipe and will provide many years of smoking pleasure. This is a wonderfully crafted pipe and has a very elegant feel to it. It took some work, but I am proud of it and the final product suits me to a T. It retains some wounds from battle, but, as Steve would say, they are part of this pipe’s story. This is one pipe that I am keeping for myself and adding to my collection. I am sure that I will be enjoying this one for many years to come. I hope you enjoyed reading the story of this pipe as much I as I did restoring it. If you are interested in more of my work, please follow me here on Steve’s website or email me directly at kenneth@knightsofthepipe.com. Thank you very much for reading and, as always, I welcome and encourage your comments.

Restoring a March 17, 2000 St. Patrick’s Day 80S Bent Bulldog

Leave a reply

Blog by Steve Laug

The next pipe has been sitting here since we picked it up on Ebay on December 6, 2016. It came to us from Aurora, Colorado, USA and I am finally getting around to working on it. It is a nice Republic Era St. Patrick’s Day Bulldog. It is stamped on the left underside of the diamond shank and reads St. Patrick’s Day. On the right side it reads Made in the Republic of Ireland (three lines) over the shape number 80S. The nickel band was in great condition and was stamped and had a Shamrock with the words Peterson’s March 17, 2000 in a circle around it. The bowl was heavily caked with a thick lava overflow on the rim top and edges. It flowed down the sides of the cap. I was hoping that the lava coat had protected the rim top and cap from significant damage but only cleaning it up would tell the full story. The finish was dirty but had some nice grain around the sides. The stem had a Peterson’s “P” logo stamped on the top of the left side of the saddle. It was lightly oxidized and had a lot of tooth marks and chatter on both sides ahead of the button. Jeff took photos of the pipe before he cleaned it up. Jeff took a photo of the rim top and bowl to show its condition. The cake is the bowl is thick and the lava on the rim and down the cap is also quite thick. The stem had tooth marks and chatter ahead of the button and quite a way up the stem surface. It was also lightly oxidized. Jeff captured some of the beautiful grain around the pipe with the next photo of the left side and heel of the bowl. It is really quite nice.He took photos of the stamping on the nickel band and the sides of the shank. It is clear and readable as noted above.  I am including the link to the Pipedia’s article on Peterson pipes. It is a great read in terms of the history of the brand (https://pipedia.org/wiki/Peterson).

Mark Irwin has a great visual history of the St. Patrick’s Day Pipes from Peterson on his rich Peterson’s Pipenotes site (https://petersonpipenotes.org/tag/st-patricks-day-pipe-2000/). He states there regarding the year 2000 issue as follows:

In 2000, the SPD series settled into a familiar and long-running guise: some variant of brown-hued smooth bowl and a nickel band with Peterson’s over a shamrock over March 17 and the year. The 2000 SPDs also featured the beloved P-Lip vulcanite mouthpiece…

Armed with that it was time to work on the pipe. Jeff had cleaned up the pipe as he normally does. He reamed it with a Pipnet Reamer and cleaned up the reaming with a Savinelli Fitsall Pipeknife. He scrubbed out the inside of the airway in the shank and stem with alcohol, pipe cleaners and cotton swabs. He scrubbed the exterior of the bowl with undiluted Murphy’s Oil Soap to remove the grime that was ground into the briar on the cap, rim and bowl. It came out looking very good. He scrubbed the stem with Soft Scrub and then soaked it in Before & After Deoxidizer. He rinsed it off and recleaned it. I took the following pictures when it arrived. It is a beautiful pipe that will come alive with buffing and polishing. I took photos of the rim top and the stem to show the condition of them both. The rim top is very clean and there is some darkening on the rim top on the back and left side. The rim edges looked very good. The stem is free of oxidation and other than the tooth marks and chatter it is in good condition. I took photos of the stamping on the band and the shank sides. It is clear and readable as noted above. The “P” logo is faded and will need to be touched up.I took a photo of the bowl and stem separated to give a sense of the shape and form of this lovely 80S Bent Bulldog.Because the pipe was in such clean condition I could start with my work without doing all the cleanup I have been doing lately. To start on this one I worked on the darkening of the rim top to match the rest of the briar. I used the 1500-2400 grit micromesh to accomplish this.I polished the briar with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I wiped it down with a damp cloth after each pad. I used it to clean off the rim top at the same time.   I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I polished the nickel band with a jewelers cloth give it a shine and to remove the oxidation. I set the bowl aside and turned my attention to the stem. I sanded out the tooth marks on the button and ahead of the button with 220 grit sandpaper and wiped it down with Obsidian Oil once I finished. I started the polishing with 400 grit wet dry sandpaper. I repainted the “P” stamp on the left side with some white acrylic nail polish. I brushed it on and scraped off the excess with a fingernail. I lightly sanded it with a 1500 micromesh sanding pad and wiped it down with Obsidian Oil.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiping it down after each pad with Obsidian Oil. I finished polishing it with Before & After Fine and Extra Fine polish. I gave it a final coat of Obsidian Oil and set it aside to dry. This Late Republic Era Peterson’s St. Patrick’s Day March 17, 2000 shape 80S Bent Bulldog is a great looking pipe now that it has been restored. The grain around the bowl is quite beautiful and the stain makes it really stand out. The finish works well with the polished vulcanite saddle P-Lip stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished St. Patrick’s Day 2000 Bent Bulldog sits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ inch. The weight of the pipe is 48 grams/1.69 ounces. I will be putting it in the Irish Pipe Makers section of the rebornpipes store shortly. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it! I appreciate your support.