New Life for a Sandblast Savinelli de Luxe Milano 506 Panel Billiard

Blog by Steve Laug

When my brother Jeff saw this pipe he went for it. He picked it up from a fellow in Pocatello, Idaho, USA. This pipe appeared to be in rough shape. The bowl was full and the sandblast was filthy. It had definitely seen better days. However, there was something about the shape that caught Jeff’s eye. The stamping on the underside of the shank reads de Luxe [over] Milano. That is followed by the Savinelli S shield logo and the shape number 506 over Italy. It is faint but readable with a loupe and light. The bowl and shank are sandblasted with a rugged blast and the panel sides all have indents where the blast went deep into the grain. It is an interesting pipe. The stain on the bowl is a medium brown that highlights the sandblast finish. It is a panel billiard with a square shank and a saddle vulcanite stem. The pipe was dirty with a thick cake and tobacco debris in the bowl. There was a heavy overflow of lava on the rim top that made it hard to know if the rim edges were damaged. There were dark areas on each side of the bowl. The grime and dirt had been ground deeply into the sandblast finish. The stem was calcified and heavily oxidized and was a brownish green colour. There was tooth chatter and tooth marks on both sides of the stem near the button and on the button surface itself on both sides. Jeff took some photos of the pipe before he did his cleanup.The next photos show the bowl and rim top. You can see the cake in the bowl and the overflow of lava and grime on the top. You can also see the likelihood of damage to the rim edges but also that it is impossible to know what it would look like once it was clean. The photos of the stem show a lot of tooth chatter on both sides of the stems. There are also some tooth marks on the button top and bottom.   The sandblast finish on the bowl, though dirty, showed interesting patterns – straight grains and birdseye. There were also some swirls in the grain. The photos also show some darkening on each side of the bowl and some dark spots. The stamping on the underside of the shank is faint but readable. It reads as noted above. I had a vague memory that there was a great photo of the same pipe in a smooth finish on the Pipephil site ( I turned there and sure enough it was not only a De Luxe it was also a 506 Panel Billiard with a smooth finish. I have included a screen capture of the section from that site below. There was also a link to a series of shape charts for Savinelli Pipes that I have found helpful in the past ( I did a screen capture of the section of the chart that included the 506 shape. Now it was time to work on the pipe. Jeff worked his magic in cleaning up this pipe. He reamed it with a PipNet reamer and smoothed the walls of the bowl with a Savinelli Fitsall pipe knife. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim and shank with a tooth brush and Murphy’s Oil Soap to the oils and tars on the bowl, rim and shank. He rinsed it under running water. He dried it off with a soft cloth. The cleaning of the stem raised more oxidation in the vulcanite. The tooth marks and chatter was clean but visible. I took the stem off and put it in a bath of Before & After Stem Deoxidizer and totally forgot to take pictures of the pipe before I started. I took photos of the condition of the rim top and stem before I started working. The rim top looks very good and the bowl is spotless. The rim top is heavily darkened and stained. The stem has light oxidation remaining and some tooth chatter and marks on both sides near and on the button.   I took a photo of the stamping on the underside of the shank. The stamping was faint but still readable. It reads as noted above.  The stem has a brass bar on the left side of the saddle.  I started my work on the bowl by dealing with darkening around the bowl sides. I took photos of the darkening. I poked and probed them with a dental pick to check on the integrity of the briar and it was solid. I also worked the areas over with a brass bristle brush and was able to remove some of the darkening. There was no cracking or checking on the inside of the bowl in each of those areas so I was fairly certain I was dealing with darkening caused by the oils of the pipeman or woman’s hands who had previously smoked the pipe. I would need to stain the pipe to deal with the dark areas. I stained the bowl with an aniline Light Brown stain. I was surprised at how dark it came out on the bowl itself. I applied the stain and flamed it with a lighter to set it in the grain. I set it aside while I had dinner to let the stain cure.   After dinner I took the pipe off the cork rest and took photos of the newly stained bowl. You can see the depth of the blast in the photos below.   I worked some Before & After Restoration Balm into the finish of the bowl, rim top and shank with my fingertips to clean, enliven and protect it. I find that the balm really makes the briar come alive again. The contrasts in the layers of stain really made the grain stand out. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The bowl really looks good at this point. I set aside the bowl and turned my attention to the stem. I “painted” the tooth marks on the surface of the stem and was able to lift them significantly. I filled in the remaining tooth marks on the button surface with clear super glue. I used a file to smooth out and shape the button. I smoothed out the remaining repairs with 220 sandpaper to blend them and started polishing with 400 grit wet dry sandpaper.     I scrubbed the stem with Soft Scrub All Purpose cleaner to remove the residual oxidation on the stem surface. The product works very well to cut through residual oxidation on vulcanite.  I polished the stem with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. I polished it further with Before & After Pipe Stem Polish – both fine and extra fine.     I really enjoy finishing the work on a pipe because I love bringing it back to life and then administering the final touches that make it sing. I put the Savinelli De Luxe Milano 506 Panel Billiard back together and lightly buffed the bowl with Blue Diamond. I buffed the stem with a heavier touch with Blue Diamond on the buffing wheel. I gave the bowl multiple coats of Conservator’s Wax and worked it into the deep sandblast with a horsehair shoe brush. I gave the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. It is fun to see what the polished bowl looks like with the smooth finish and the black vulcanite saddle stem. This richly finished De Luxe Milano Panel Billiard is light weight and ready for you to load up a tobacco of preference and enjoy smoking it. Have a look at it in the photos below. The dimensions are Length: 5 ¼ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 33grams/1.16oz. This is one that will go on the Italian Pipemakers section of the rebornpipes online store shortly. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next generation.           

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.