Tag Archives: Stem repairs

Refreshing a Beldor Studio Mini Churchwarden Paneled Apple of Saint Claude

1 Reply

Blog by Dal Stanton

The Beldor Studio on my worktable now came to me from what I call the French Lot of 50.  I was tipped off by a fellow pipe man friend in Romania who acquired a L. J. Peretti Oom Paul from me.  He saw 5 different lots of pipes on the French eBay auction block and sent me a note. My thinking is that one of the Lots might be a good addition to my online collection, For “Pipe Dreamers” Only!, where pipes may be commissioned by those who can see the potential of unrestored pipes.  The different lots were from the same seller in Paris and his approach to selling these lots was like throwing bloody chum in shark infested waters!  Each lot was in a pile of pipes with different angles of the pile pictured in the lot’s listing.  Studying each of the piles was exhilarating trying to see markings on the pipes and characteristics that might reveal treasures in the mix.  I finally chose to bid on one of the French Lots because it had a very interesting Cutty shape (Restoration here: A Cutty Tavern Pipe – Recommissioning a Historical Classic as a Gift for a Steward of History) sprawled across the top of the pile and several other very, very interesting candidates.  The other characteristic of the French Lot of 50 that drew my attention were several pipes brandishing horn stems – very much pointing toward WW2 and post era pipes when rubber was scarce, and horn became a predominant replacement for stems.  With some effort, I found the Beldor Studio buried in the middle of the pile – one arrow on the inverted stummel and the other on the end of the stem barely visible.  I bid on the French Lot of 50 and the bid prevailed.  It did not take long for the package to come from Paris reaching me in Sofia, Bulgaria.When the pipes arrived, I did my normal cataloging of each pipe and promoting their arrival on various Facebook Pipe groups and many of these pipes have already been restored and with new stewards.  The Beldor Studio was waiting for Daniel to find in the online collection, For “Pipe Dreamers” Only!  I received Daniel’s inquiry about commissioning the Beldor and he identified himself as the son of a colleague and acquaintance of mine in Pennsylvania!  Daniel expressed his enjoyment of reading the write ups on the restoration of pipes and that he was interested in the Beldor Studio.  I sent this description of the Beldor to help Daniel with his decision:

I appreciate your interest!  The pipe you are interested in is a sweet pipe.  I called it a small Churchwarden, or it could possibly be categorized as a ‘Pencil Stem Panel’.  It’s a petite size and the paneled bowl is very nice.  I haven’t worked on a pipe with this marking before so I can’t say at this point anything about the collectability of a ‘Beldor Studio’ so we’re looking primarily at the pipe itself.

I’m glad that in the end, after giving Daniel an estimate of the final valuing of the pipe, he agreed and the Beldor Studio went into The Pipe Steward queue of pipes that benefit the Daughters of Bulgaria – women and girls who have been trafficked and sexually exploited.   Here are pictures of the Mini Churchwarden or Pencil Stem that got Daniel’s attention with a measurement of 7 1/2 inches in length and the bowl height of 1 1/8 inches.The only markings on the pipe are on the left shank flank with these stampings: ‘BELDOR’ [over] ‘STUDIO’.  The stem is stamped with a circle.This is one of those frustrating pipes that are seen in many places on the internet for sale, but not much is known.  The nomenclature on the Beldor Studio gives no indication of country of manufacturer (COM) but it becomes evident that the origins are French and from the pipe making center, Saint Claude.   Pipephil.eu confirms the French origins.  The lettering of ‘Beldor’ is the same with the circle stem stamp being the same.Pipedia only confirms a French origin and adds different lines with the Beldor name: Maker unknown; series: De Luxe, Golf, Western.  The Saint Claude origin in France simply comes from a Beldor pipes that are listed for sale on various sites with the nomenclature on these pipes include Saint Claude.  Here is one such example (LINK):I searched for some connection to an actual manufacturer in Saint Claude and could find none.  As a ‘hail Mary’ I sent some emails to pipe shops located in Saint Claude to see if any might have more information.  We’ll see what if I receive any helpful responses!  I did confirm the Beldor ‘Studio’ as the specific line for the Mini Churchwarden with this offering on a French eBay listing that described the center pipe as “BELDOR STUDIO BRUYERE SAINT CLAUDE”.I now take a closer look at the pipe on my worktable.  I like the petite panel bowl mounted on the pencil stem.  It has Churchwarden proportions but on the miniature.  The diminutive bowl would work well when one doesn’t have a lot of time to enjoy a bowl.  For me, I’m not a strong, nicotine ‘kick in your pants’, tobacco person, but I do like trying stronger tobaccos but in smaller portions.  This bowl would be perfect for this.  The former steward used this pipe as the chamber indicates some cake build up.  The beveled paneled rim has a heavy lava flow caked on it and this needs to be cleaned and refreshed.The hexagonal paneled apple bowl is very attractive.  It is dirty with grime and reveals normal scratches and scuffs from wear but reveals some genuinely nice grain. The pencil stem has some oxidation and tooth chatter on the bit.To begin the recommissioning of this Beldor Studio Mini Churchwarden, I remove the stinger and put aside for safe keeping.  I’m not a stinger fan but I’ll clean it and replace it to send to the new steward to decide what to do with itNext, using one pipe cleaner wetted with isopropyl 95%, the stem’s airway is clean.I then add the Beldor Studio stem to a soak of Mark Hoovers ‘Before & After Deoxidizer’ (www.ibepen.com) along with several other pipes in the queue.After a few hours soaking in the Deoxidizer, the Beldor stem is removed from the Deoxidizer and after squeegeeing the liquid off the pipe with my fingers, I use cotton pads wetted with isopropyl 95% to wipe away the raised oxidation.  A few pipe cleaners wetted with isopropyl 95% are also used to clear away Deoxidizer from the airway.To help condition the vulcanite stem, paraffin oil is applied and rubbed into the surface.  The stem is put aside to allow the oil to be absorbed. Turning now to the paneled bowl, I start by reaming the small chamber.  I use only the smallest blade head in the Pipnet Reaming Kit to clear the cake.  Following this, the Savinelli Fitsall Tool scrapes further on the chamber walls.  Finally, I sand the chamber with 240 grade paper wrapped around a Sharpie Pen. After wiping the chamber with a cotton pad, the chamber appears to be healthy – no heating problems detected.Transitioning now to the externals of the stummel, the picture above shows the thick lava flow caked on the rim that needs to be cleaned as well as the entire bowl.  Using undiluted Murphy’s Oil Soap, I begin using a cotton pad to scrub the stummel’s surface as well as the rim.  The rim also requires the brass bristled brush and the sharp edge of my Winchester pocketknife.  I use the knife’s edge carefully to scrape the black on the rim.  The brass brush also helps as the lava starts to break apart.  In time, I move to the kitchen sink to continue the cleaning using shank brushes and anti-oil liquid dish soap to work on the mortise internals.  After a thorough rinsing with warm water, I go back to the worktable and take a picture showing the results of the cleaning.The rim cleaned well but the front left rim panel section has a burn scar that will require additional attention.Another result of the cleaning was to reveal a thin finish on the Beldor stummel.  The next three pictures show blotches of shiny and dull areas.  The shiny indicates old finish hanging on, whereas the dull is raw briar.  The second picture shows a small fill that may need to be addressed. While I am focused on the residue of the old finish, I decide to address it now.  I first used alcohol and a cotton pad to see if it would break down the residue of finish. It did not.  I then use acetone first with a cotton pad, which worked but slowly.  Next, I used acetone with the gentle abrasion of 000 steel wool. This did the trick.  I was able to remove all the old finish which is a good starting point.  I take a couple of pictures to show the clean stummel. Backtracking now in my normal cleaning cycle, I now focus on the internal cleaning of the mortise and airway.  I use only one pipe cleaner and cotton bud wetted with isopropyl 95% to discover that the internals are clean.  I move on!Earlier I identified a fill on the right side of the stummel.  Using a sharp dental probe, I test the fill and find that it has shrunk and unstable.  I dig out the old fill to apply a new patch to the pit.After wiping the area with alcohol to clean it, using regular CA glue, I spot drop some glue on the pit.  I then cover it with briar dust that helps blend after the sanding of the patch area.  I put the stummel aside to allow the patch to cure.With the stummel on the sideline, I turn to the Mini Warden stem which is in particularly good shape.  There is almost no tooth chatter on the bit.  There is one small compression on the upper bit that needs addressing.I also detect some oxidation remaining on the end of the stem on the shank side. Using 240 paper, the upper and lower bit is sanded to remove any lasting tooth chatter and the one compression.The 240 paper is also deployed on the end of the stem where oxidation was detected.  I’m careful to avoid the Beldor ‘O’ stamping on the stem.To be on the safe side, I cover the stem stamping with masking tape to protect it.  Next, 600 grade paper is used to wet sand the entire stem.  Following this, 000 steel wool finishes further.Next, the full regimen of micromesh pads is used on the stem.  To begin, I wet sand with pad 1500 to 2400 and follow with dry sanding with pads 3200 to 4000 and 6000 to 12000.  Between each set of three pads, Obsidian Oil is applied to the stem to condition it and to protect it from oxidation in the future.To further condition the stem and to work on the area of the Beldor ‘O’ stem stamping to clean it up after it having been covered to protect from sanding, I use Before & After Fine and Extra Fine Polishes. Starting with the Fine polish, I apply it on the stem after putting a small amount on my fingers. I work it into the vulcanite and allow it to absorb for 15 to 20 minutes. After this time, I wipe off the excess polish with a paper towel, continuing to work the polish in as I do this. Next, in the same way, the Extra Fine Polish is applied.  After 20 minutes, the excess is removed, and the stem is buffed with a microfiber cloth.Turning again to the stummel, the small patch on the right panel has cured.I first use a flat needle file to file down the patch mound then it is further smoothed and blended with 240 grade sanding paper.Next, I address the dark scorched areas of the rim.  The internal edge of the rim is a ring of black from the burning.  The next two pictures show the condition of the rim. I use the 240 paper to clean the rim and to blend the different contours.  The rim is beveled and tapers downward toward the chamber.  I go with this bevel to help mask and blend the burn mark that is on the front left panel. I follow with 600 grade paper further smoothing and blending.With the sanding and blending utilizing the tapering of the rim, the rim definition has been blurred.  To redefine the hexagonal rim, I do a light topping using only 600 grade paper.  The picture below shows how the rim was reestablished and a defined bevel line.  I like it!Next the stummel is sanded with the full regimen of micromesh pads from 1200 to 2400, which is wet sanded, then dry sanded from 3200 to 4000 and then 6000 to 12000. Next, to tease out the rich briar hues, Before & After Restoration Balm is used.  After applying some on my fingers, the Balm is worked into the surface starting with a cream-like texture then gradually thickening after it is worked into the briar. After applied, I put the stummel aside for a few hours for the Balm to do its thing.  The picture below is of this period.  Afterwards, the stummel is buffed with a microfiber cloth to remove the excess Balm and to raise the shine.With the stem and stummel reunited, Blue Diamond compound is applied to the entire pipe with a cotton cloth buffing wheel set at about 40% full power on the Dremel.After the application of the compound is finished, the pipe is buffed with a felt cloth to remove the compound dust that is left behind.Before applying wax, I have a couple additional projects to do.  The shank on this Mini Churchwarden is very thin and makes me nervous about it being cracked.  To guard the shank as well as add a bit more class to this sharp looking pipe, I fit the shank with a brass shank cap. The cap acts as a band as well as curling over the shank facing to serve as a spacer. I find a fitting that will work.  I apply a small amount of CA glue to the inside of the fitment and use a toothpick to paint the inside circumference of the ring. After placing the cap partially over the shank to start it, I use the stem itself, to press the cap into place.  This serves to create the perfect symmetry with the shank cap butting against the stem facing.  This helps close any gaps that may exist between the two.  The shank cap looks great – I like it! The next project is to try to fill the ‘O’ stem stamp with white acrylic paint to freshen it.  My concern is that the stamping is no longer defined enough to hold a full circle.I place white acrylic paint over the stamping and spread the paint with a toothpick.I then tamp the wet paint with a cotton pad to remove the excess and quickening the drying process.I then use a toothpick’s flat edge to gently scrape the dried paint to achieve an almost whole ‘O’.  It looks good.I use 000 steel wool to clean up the stinger and reinsert it into the nickel tenon.  Tarn-X Tarnish Remover gives a new shine to the brass shank cap.  I use the cotton pad to apply the polish.Finally, with the full ensemble united, I apply carnauba wax with the Dremel.  Using another cotton cloth buffing wheel with the Dremel set at 40% of full power, wax is applied to the stem and stummel.  Afterwards, I use a microfiber cloth to give the pipe a rigorous hand buffing to raise the shine.I am pleased with the results of this Beldor Studio Mini Churchwarden.  The hexagonal paneled bowl gives an elegant presentation as it is mounted on the subtly curved pencil stem.  I like the brass shank cap – it adds a bit of class to a very nicely flowing pipe.  Daniel commissioned this pipe and he will have the first opportunity to acquire it from The Pipe Steward Store.  This pipe benefits the Daughters of Bulgaria – women and girls who have been trafficked and sexually exploited.  Thanks for joining me!

Cleaning up a Willmer Straight Grain AAA Standard Cup and Saucer

1 Reply

Blog by Steve Laug

The next pipe on the table is a shape I would call a cup and saucer or at least Willmer’s take on this shape. The pipe is stamped on the left side of the shank Willmer in script over Straight Grain over AAA over Standard. On the right side of the shank it is stamped Made in England. It is a bent cup and saucer shaped smooth briar with vulcanite saddle stem. The pipe was dusty and dull looking but had great grain around the bowl and rim. The rim top is smooth and there was some darkening and damage to the inner edge of the bowl. There was a thick cake in the bowl. The finish was in great condition under grime ground into the sides and shank. The saddle vulcanite stem was oxidized and had light tooth marks and chatter on both sides near the button. Jeff took the following photos before he started his cleanup work on the pipe. He took close-up photos of the bowl and rim top from various angles to capture the condition of the rim top and edges of the bowl. There was a little darkening around the inner edge and heavier along the back edge of the bowl. There are some scratches on the top and outer edge of the bowl as well. You can also see the cake in the bowl.He took photos of the sides and heel of the bowl to show the condition of the finish and the grain around the bowl. The pipe has some stellar grain around the bowl and shank and the carver maximized the lay of the grain with the shape of the pipe. Jeff took photos of the stamping on the sides of the shank. It reads as noted above and is clear and readable.  He also took a photo of the Willmer “W” on the left side of the stem. The next photos show the top and underside of the stem. You can see the light tooth marks right next to the button edge.I turned to Pipephil to get a quick review of the Willmer Company as it had been a long time since I had worked on one (http://www.pipephil.eu/logos/en/logo-w3.html). I quote the side bar from the site bellow.

Willmer is a brand of H. Willmer & Son Ltd. The factory closed down about 2006-07 after more then 60 years activity and two generations of makers. Gradings until the 1980s (ascending): BA, A, AA, and AAA. After this date Willmer introduced the AAAA and AAAA PRESENTATION as top grades.

The pipe I was working on has a AAA stamping on it which if the pipe came from pre-1980s was the top of the line. If it was later pipe it close to the top of the line.I turned to Pipedia to get more information on the brand (https://pipedia.org/wiki/Willmer). The first paragraph dispelled of the belief that Willmer had been a carver for Charatan in his own words. I quote a portion of the article to give a sense of the history of the brand.

Willmer was founded in London. According to the website, which doesn’t exist anymore because the Willmer factory has been closed in 2006/07, the firm was in business “for more than 60 years” by 2003. Willmer was homed then in Southend-on-Sea, Essex, so not far from the Cadogan plant.

When Willmer first started, they definitely strived to compete with brands in the high-end market. Due to the excellent quality of the pipes Willmer was frequently asked to produce private label pipes for England’s best renowned pipe retailers. So many pipes are not easily recognized as Willmers for stamped under the name of the respective shop. Willmer’s own pipes were stamped “Willmer – Made in England” and showed a sweeping “W” in white or gold on top or left side of the stem. The earlier grading had AAA as top grade followed by AA, A, AB etc.

Sometime in the 1980’s, Willmer went through some major changes. The move to Essex was already mentioned above. They continued making highly respectable freehands – often copying some of the stunning Charatan shapes of days gone by. The grading was altered. What used to be an AAA now became the additional name “Presentation” and was stamped with AAAA. Funny enough, the forth A was often larger than the three before. The other grades were changed accordingly.

Now it was time to look at it up close and personal. Jeff had done his usual thorought job in removing all of the cake in the bowl and the lava on the rim top. He had reamed the bowl with a PipNet Pipe Reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife. He took the cake back to bare briar so we could check the walls for damage. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime on the bowl and rim and was able to remove the lava and dirt. He cleaned out the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol until they came out clean. He cleaned the stem with Soft Scrub to remove the grime on the exterior and cleaned out the airway with alcohol, cotton swabs and pipe cleaners. I took photos of the pipe before I started my part of the work. To show the damage to the inner edge of the rim and the rim top I took a close-up photo. You can see it on the right inner edge and the back edge of the bowl. The vulcanite stem had some tooth marks on both sides and there was some oxidation remaining.I took a photo of the stamping on both sides of the shank. It clearly read what was noted above. The “W” stem on the left side of the saddle stem is also readable.I removed the stem from the bowl and took photos of the parts. It really is a great looking pipe.I started my part of the restoration by addressing the damage to the rim top and inner edge of the bowl. I topped the bowl on a topping board with 220 grit sandpaper. I worked over the inside edge of the bowl with a folded piece of 220 grit sandpaper.I polished the newly topped rim and the rest of the bowl with 1500-12000 grit micromesh sanding pads. I wiped the bowl down with a damp cloth after each sanding pad to remove the dust and debris. I stained the rim with a Maple Stain Pen to blend the repaired and polished rim into the rest of the bowl.I rubbed the bowl and shank down with Before & After Restoration Balm to deep clean the finish on the bowl and shank. The product works to clean, enliven and protect the briar. I worked it in with my fingertips into finish on the bowl and shank. I let it sit for 10 minutes to let it do its magic. I buffed it with a soft cloth. The briar really began to have a rich shine. I took some photos of the bowl at this point to mark the progress in the restoration. The bowl was finished so I set it aside and turned my attention to the stem. To address the oxidation and the tooth marks on the stem surface I sanded it with 220 grit sandpaper to blend in the tooth marks and to break up the oxidation. I started the polishing with 400 grit wet dry sandpaper.I started polishing the stem with Denicare Mouthpiece Polish – a red gritty paste that feels a lot like Tripoli. I find that it works well to polish out some of the more surface scratches in the vulcanite left behind by the 400 grit wet dry sandpaper. I rub it into the stem surface with my fingertips and buff it off with a cotton pad.I touched up the “W” stamp on the stem with PaperMate Liquid Paper. I pressed it into the stamp in the vulcanite with a tooth pick. Once it dried I scraped off the excess fill with the tooth pick and with micromesh sanding pads.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped the stem down after each sanding pad with a cloth containing some Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. I wiped it down with a final coat of Obsidian Oil and set it aside to dry. This is a unique pipe and it is the first one I have worked on like this. It is a beauty. I put the bowl and stem back together again and buffed the bowl and the stem with Blue Diamond on the buffing wheel. I gave the bowl and the stem several coats of carnauba wax. I carefully buffed the entire pipe with a clean buffing pad to raise the shine. I finished buffing with a microfiber cloth to deepen the shine. The finished pipe looks very good. The grain is quite beautiful a mix of straight and flame around the bowl sides and birdseye on the rim top and heel. The pipe feels great in the hand. It has an interesting shape that fits well in either the right or left hand. The finished Willmer Straight Grain AAA Standard is shown in the photos below. The dimensions of the pipe are Length: 6 ½ inches, Height: 2 inches, Outside diameter of the bowl: 2 inches, Chamber diameter: ¾ of an inch. This great looking Willmer Cup and Saucer pipe turned out very well. It should be a great pipe. It will be going on the rebornpipes store shortly if you are interested in adding it to your collection. Thanks for reading this blog and my reflections on the pipe while I worked on it.

An Easy Restoration of a JM Boswell 2013 Bent Poker Sitter

Leave a reply

Blog by Steve Laug

I have been doing a fair bit of work on the last few restorations so I thought it was about time to work on an easy one next. I took another of the Boswell pipes out of box of pipes to be restored to be my next project. I cleaned up an unsmoked JM Boswell volcano recently and posted the blog on it here (https://rebornpipes.com/2020/04/08/life-for-a-j-m-boswell-2013-bent-volcano-with-a-twist/). I also restored a second estate Boswell – a bent billiard with a twist. Here is the link to that blog (https://rebornpipes.com/2020/04/08/life-for-another-j-m-boswell-2013-bent-billiard-with-a-twist/). In both of those blogs I gave quite a bit of background information on the brand and its maker. If you would like to know more about the brand you can click on either link and have a read.

The next Boswell is also a 2013 pipe and this one has more of a standard shape to it. It is a bent Poker or Cherrywood Sitter shaped smooth briar with an acrylic saddle stem. The pipe was dusty and dull looking but had great grain around the bowl and rim. The rim top is smooth and clean with no darkening or lava overflow. The finish was very dirty from sitting around. There was a moderate cake in the bowl. The inner edge of the rim appeared to be in excellent condition. The pipe was signed on the underside of the shank with JM Boswell’s signature and 2013 U.S.A. There are no other stampings on the pipe and no shape numbers. The saddle acrylic stem was in good condition with just a few light tooth marks and chatter on both sides near the button. Jeff took the following photos before he started his cleanup work on the pipe. He took close-up photos of the bowl and rim top from various angles to capture the condition of the rim top and edges of the bowl. There was a little darkening along the back edge of the bowl but otherwise it was clean.He took photos of the sides and heel of the bowl to show the condition of the finish and the grain around the bowl. You can see the small minor sandpits on the left side and on the heel of the bowl but otherwise it a clean piece of briar. Jeff took a photo of the signature and date on the underside of the shank. It reads as noted above and is clear and readable. The next photos show the top and underside of the stem. You can see the light tooth marks right next to the button edge.Now it was time to look at it up close and personal. Jeff had done his usual thorough job in removing all of the cake in the bowl and the lava on the rim top. He had reamed the bowl with a PipNet Pipe Reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife. He took the cake back to bare briar so we could check the walls for damage. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime on the bowl and rim and was able to remove the lava and dirt. He cleaned out the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol until they came out clean. He cleaned the stem with Soft Scrub to remove the grime on the exterior and cleaned out the airway with alcohol, cotton swabs and pipe cleaners. I took photos of the pipe before I started my part of the work. To show how clean the rim top and stem really were I took a close-up photo of the rim and stem. The bowl was clean and cake free. The inner edges of the bowl look good. The acrylic stem cleaned up nicely. The surface had some tooth marks but the button edge looked really good.I took a photo of the signature on the under side of the shank.I removed the stem from the bowl and took photos of the parts. It really is a great looking pipe.I polished the briar with 1500-12000 grit micromesh sanding pads. I wiped the bowl down with a damp cloth after each sanding pad to remove the dust and debris. I rubbed the bowl and shank down with Before & After Restoration Balm to deep clean the finish on the bowl and shank. The product works to clean, enliven and protect the briar. I worked it in with my fingertips into finish on the bowl and shank. I let it sit for 10 minutes to let it do its magic. I buffed it with a soft cloth. The briar really began to have a rich shine. I took some photos of the bowl at this point to mark the progress in the restoration. The bowl was finished so I set it aside and turned my attention to the stem. To address the tooth marks on the stem surface I sanded it with 220 grit sandpaper to blend in the tooth marks. I started the polishing with 400 grit wet dry sandpaper.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped the stem down after each sanding pad with a cloth containing some Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. I put the bowl and stem back together again and buffed the bowl and the stem with Blue Diamond on the buffing wheel. I gave the bowl and the stem several coats of carnauba wax. I carefully buffed the entire pipe with a clean buffing pad to raise the shine. I finished buffing with a microfiber cloth to deepen the shine. The finished pipe looks very good. The grain is a mix of patterns around the sides, top and bottom of the bowl and is quite beautiful. The pipe feels great in the hand. It is comfortable and light weight. The finished JM Boswell 2013 Bent Poker/Sitter is shown in the photos below. The dimensions of the pipe are Length: 5 ¼ inches, Height: 2 ½ inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: 7/8 of an inch. This great looking Boswell Poker turned out very well. It should be a great pipe. It will be going on the rebornpipes store shortly if you are interested in adding it to your collection. Thanks for reading this blog and my reflections on the pipe while I worked on it.

Renewing Paw’s Kaywoodie “500” Round Shank Bulldog – The Third Pipe of a Great Grandfather’s Legacy

1 Reply

Blog by Dal Stanton

This Kaywoodie “500” is the final of three pipes Joe sent.  It belonged to Paw, Joe’s wife’s great grandfather.  I’ve enjoyed learning about Paw, or ‘2-Page Sam’, the name given to him by his fellow workers of Brown & Williamson Tobacco, Corp, founded in the 1800s in Winston-Salem, North Carolina. In the restoration of the first of three, a Medico Apollo Brylon (See: Another Legacy Pipe of a Great-Grandfather: Challenges Working with ‘Brylon’ on a Medico Apollo) an article in the B&W Tobacco, Co.’s company magazine, Pipeline, Sam’s 43-year career was showcased and it described how he became known as ‘2-Page Sam’.  As a salesman for the tobacco company, Sam’s daily goal was to secure enough orders from clients he would visit, ‘Ma & Pa’ establishments mostly, to reach page two of the order book for the day.  This company-wide work ethic, along with how the article captures Sam’s sincere respect for people – his fellow M&W employees and supervisors as well as the normal working-class people he sold to that made his livelihood possible.   Joe sent the picture on the left, below, of Sam among fellow employees of B&W.  I’m not sure which one is Sam but, my guess is the top, fourth man from the left!  The picture on the right is Sam (standing on the right) – capturing a moment in an age long gone.The second of Sam’s pipes that I just restored (See: Bringing to Life a Unique Kaywoodie Natural Burl 33 – Another Legacy Pipe of a Great Grandfather) was a rarer, Kaywoodie ‘Natural Burl’ 33, Apple shape.  It turned out very, very well and even included the collaborative help of Bill Feuerbach, Kaywoodie’s – or more correctly, S. M. Frank Co.’s, president, the holding company of Kaywoodie, Medico and Yello Bole.  The last of the three is on the worktable now, the Kaywoodie “500” IMPORTED BRIAR US Pat. 2808837 50C.  Here are a few pictures to take a closer look. The nomenclature on both sides of the shank is clear.  The left flank is stamped KAYWOODIE [over] “500” [over] IMPORTED BRIAR [over] PAT. 2808837.  The right side of the shank is stamped with the Kaywoodie shape number, ‘50C’.  The stem holds the classic inlaid Kaywoodie shamrock or clover. The first interesting aspect about this Kaywoodie is the shape designation.  When I first saw pictures of the pipe that Joe sent, I made the immediate identification of the shape to be a compact Rhodesian.  When I looked up the Kaywoodie shape number in the extensive list provided by kwguy originally in the Kaywoodie forum listed also in Pipepedia’s listing, the description surprised me:

50C Small bulldog, round shank 1960-1963

My main pipe shape ‘go to’ is Bill Burney’s Pipedia’s Pipe Shapes  where the debate is described:In deference to Kaywoodie, I’ll call Paw’s pipe a small Round Shank Bulldog.  What was also helpful is that the short period that the Round Shank Bulldog was in production is small – 1960 to 63.  Pipephil.eu’s comments on Kaywoodie’s
500 and 600 series were that they were cheaper, low-end pipes that ran through the period: 1959 – 1967.  It’s probable that Paw’s Kaywoodie “500” Round Shank Bulldog which isolates it as a “500” that was marketed between 60 to 63, cost him $5.95.  The 1962 Kaywoodie catalog page that Bill Feuerbach provided to include in the restoration write-up of Paw’s Kaywoodie Natural Burl, also included an ‘All New Kaywoodie “500”’ advertisement.  Bill’s explanation of the page below indicated that the cost of the pipe, $5.95, identified it as the 1962 catalog which would have encompassed the 1960 to 1963 timeframe of the round shank Bulldog production. The Kaywoodie “500” add also touts a “Syncro-Lok Stem” and a “New Miracle Finish” which lasts for years.  The “Syncro-Lok Stem” was a component part of the US Pat. 2808837 which is stamped as part of the “500” nomenclature.  According to Pipedia’s Kaywoodie article, the 1957 Pat. 2808837 applies specifically to the metal on metal fittings developed by Kaywoodie (Picture below courtesy of Doug Valitchka).  It was interesting for me recently to hear Bill Feuerbach, president of S. M. Frank Co., describing the era of Kaywoodie’s metal fitments coming to a close in his January, 2016, interview with Brian Levine on the  Pipes Magazine Radio Show.  Some reasons discussed were the changing landscape of pipe smokers where ease of cleaning and the fact that today’s pipe smoker, representing a younger generation, is not using the pipe as rigorously as those of earlier generations.  The other primal reason that Bill gave were the economics – the company that had manufactured these parts for Kaywoodie no longer was in business and finding a replacement ended up not making economic sense. With a better understanding of the Kaywoodie “500” on my worktable, I now take a closer look at the Bulldog’s issues.  The cake in the chamber is not thick in the upper chamber, but tightens toward the floor of the chamber. The rim is classic ‘2-Page Sam’ as it has sustained Sam’s rushed knocking damage on the aft quadrant of the rim – but it’s not severe.  As with the other 2 pipes, and with Paw’s Kaywoodie “500” Long Shank Billiard that I restored for Joe last year, this “500”’s rim will also carry these marks in remembrance of Paw. The internal edge of the rim has a large divot which I will repair.  The rest of the rim shows some grime and nicks on the external edge which one would expect.  The finish on the “500” series to me is not preferred.  In the Kaywoodie “500” add above it describes the finish as a “New Miracle Finish” which lasts for years.  As with the other “500”, to me the acrylic-like finish is not as attractive as a natural briar shine.  The ‘candy apple’ shine I will remove in order to reveal better the grain beneath.  The stem is thick with deep residual oxidation and the bit is caked with calcium deposits.  There is tooth chatter, but the button seems to be in good shape.One last issue is that the Kaywoodie screw in stem is slightly under clocked.  This will need a small adjustment and may even correct itself through the cleaning.  With the help of my mouse and box of matches, I’m able to show the stem’s orientation.To begin the restoration of the last of Paw’s pipes, I start by working on the stem. I first clean the internal airway with pipe cleaners wetted with isopropyl 95%.  In order to reach through the tight quarters of the 3-hole stinger, a shank brush is used to help clean.To get a jump on dealing with the oxidation and calcium deposits, I take the stem to the kitchen sink and use a Soft-Scrub-like product here in Bulgaria called CIT.  Using 000 steel wool, I scrub the stem with the CIT cleaner.  The results look good, but I’ll probably use 240 sanding on the stem after seeing how the soak with Before & After Deoxidizer goes.The Kaywoodie “500” stem then joins other pipes in the queue for a soak in the Deoxidizer. After a few hours in the soak, the Kaywoodie’s stem is taken from the Deoxidizer and drained of the excess fluid to save it for future use!  After I squeegee the liquid with my fingers, I again use a pipe cleaner wetted with isopropyl 95% to clear the remaining Deoxidizer from the stem’s airway and a cotton pad, wetted with alcohol, is used to wipe away oxidation raised by the soaking process.Then, to condition the vulcanite stem, paraffin oil, a mineral oil, is applied to the stem and set aside to absorb.Turning to the Kaywoodie “500” Bulldog stummel, the chamber has cake that thickens as it moves toward the chamber floor.  To remove this cake buildup, the smallest blade of the Pipnet Reaming Kit goes to work on the small chamber.  After using only this blade head, the Savinelli Fitsall Tool is employed to further scrape the chamber walls removing more carbon cake buildup.  Next, using 240 grade paper wrapped around a Sharpie Pen, the last vestiges of carbon are removed from the chamber wall.  After wiping the chamber with a cotton pad wetted with alcohol to clean the carbon dust residue, an inspection reveals a healthy chamber. Transitioning now to the external cleaning, the rim has some darkening from lighting and light lava flow. The stummel has normal grime. The second picture below shows the shininess of the acrylic-like finish.  I’m interested to see how the finish holds up through the cleaning.Undiluted Murphy’s Oil Soap is used on a cotton pad to begin the external cleaning.  A brass wired brush is also used to clean the rim.  After some cleaning, the stummel is taken to the kitchen sink where with shank brushes and anti-oil liquid dishwashing soap is used to clean the mortise and airway using warm water.  After a good scrubbing, the stummel is rinsed thoroughly and after returning to the worktable, I take a picture to show the results of the cleaning.Next, returning to cleaning the internals, I use cotton buds with pipe cleaners wetted with isopropyl 95% to do the job.  The metal threaded shank insert is small, and this makes it difficult for the cotton buds to exit with their buds!  The buds are pulling off the sticks in the close quarters and that makes retrieval difficult.  I discover in the end, if I ‘unscrew’ the buds when extracting them, the threads help instead of grabbing the buds.  This makes cleaning a bit slower.  A small dental spoon is helpful is scraping the mortise walls and excavating old tars and congealed oils.  Another helpful technique was folding two bristled pipe cleaners and twisting the ends together.  This provides the action of 4 pipe cleaners in the mortise at one time enhancing the cleaning action.  In time, the buds are coming out lighter and I transition to cleaning with a kosher salt and alcohol soak.The hour is late, and I’ll let the soak go through the night.  Kosher salt and isopropyl 95% are used for the soak and this method of cleaning helps to freshen the internals for the new steward.  I first fashion a ‘wick’ by pulling and twisting a cotton ball.  It is then inserted and guided down the mortise and airway with the aid of a stiff wire.The chamber is then filled with kosher salt, which leaves no aftertaste, and placed in an egg carton for stability.  Using a large eyedropper, the chamber is then filled with isopropyl 95% until surfacing over the salt.  After a time, the alcohol is absorbed, and I top the bowl off once more with alcohol and turn out the lights.The next morning, I discover that the salt and wick have soiled little which usually is a good indicator that last night’s cleaning was effective.  After tossing the expended salt in the waste and clearing the salt from the stummel with the use of paper towel and by blowing through the mortise, I use a few more pipe cleaners to complete the internal cleaning.Next, I take another look at the stummel surface and finish.  As with Paw’s Kaywoodie “500” I restored for Joe last year, the candy apple shine of the acrylic-like Kaywoodie finish lingers.  My preference is to remove the finish and to get down to the natural briar.Another reason for removing the old finish is the fact that it’s already been removed on the rim from Paw’s knocking on the back side of the rim.  Raw briar is already exposed here but the wear on the rim edge also shows where the finish is either gone or very thin.The most efficient way I found to remove the Kaywoodie “500” finish from my previous experience is with acetone.  Starting with cotton pads I incessantly rub the surface with the cotton pads wetted with acetone.  From the very beginning, the red dye begins to show on the cotton pads as the acetone breaks down the old finish.The next picture shows the progress on the stummel surface.  The shiny surface indicates old finish hanging on.  Next to it, you can see splotches of dull surface – the goal!The progress is slow with the cotton pads, so I transition to utilizing 000 steel wool wetted with acetone.  This does the trick as the following pictures show.  I’m amazed at the grain that I can now see, and it’s not half bad!  Even though I do not prefer the thick acrylic-like finish, the upside of it at this point is that it has successfully protected the stummel’s surface from damage.  Most of the nicks and scratches that could be seen before were superficial damage to the finish shell and not to the briar.  As I inspect the stummel, I’m seeing a practically pristine surface. Before moving further with the stummel’s finishing, the divot on the rim needs attention.  It’s located on the internal edge just in front of Paw’s skinned rim backside.  It’s small but filling it will provide a better rim presentation.I fill the divot by mixing a very small amount of thick CA glue with briar putty.  After placing both the briar dust and glue on the mixing palette, I use a toothpick to draw the briar dust into the glue until it reaches the thickness of molasses at which time I apply it to the divot. I use an accelerator to quicken the curing time of the patch.  I next use both flat and half-round needle files to remove the excess briar putty patch.After doing the primary removal with the needle files, 240 grade sanding paper finishes the patch blending at this point.With the 240 paper in hand, I do a quick internal rim edge sanding.  There is a dark ring remaining on most of the internal rim that is cleaned up.Taking a close look at the rims condition, there are nicks throughout the external rim’s edge.  There are also pits here and there which need cleaning.I decide to do a very gentle cosmetic topping of the stummel to clean the rim and give it a fresh definition.  Using the chopping board for my topping board, I first place 240 grade paper on it.  With the stummel inverted, I give the bowl a few rotations and check. Then, after a few more rotations, I’m satisfied.  I’m not concerned with Paw’s aft knocking damage – that remains.  I’m concerned that the rest of the rim enjoys fresh rim lines.  This is especially with a Rhodesian and Bulldog – the twin dome lines that encircle the bowl give these pipes their unique shapes. Then, switching to 600 grade paper on the topping board, the stummel goes a few more rotations to smooth things out further.Next, I use sanding sponges to further erase minuscule nicks and scratches and to start the process of coaxing out the grain that has been waiting beneath the heavy finish.  Starting the sanding with a coarse sponge is followed with a medium then light grade sponge. I avoid the nomenclature except with the final sponge. HOLD THE PRESS! – At this point I had moved into the process of applying the full regimen of micromesh pads to the “500” and Steve had published a really good write up on rebornpipes that caught my attention which I was reading as I sanded (See: Operation Rescue – “My Dog Ate my Ser Jacopo L1 Billiard!”).  He described the process of applying rustication, a skill that I’ve not had too much experience with, and I was very interested in the processes he described.  One of these processes that dovetailed with my current musings about the Kaywoodie “500” on my table was the staining process.  Steve described in his write-up using a black undercoat stain followed by a mahogany on the smooth briar parts of his project (See picture).  He also described the reasoning and the other micro steps leading into and out of this process. The motif of the Kaywoodie “500” series is obviously red, but the grain underneath is dark to stand out in contrast to the light wood.  Last year when I restored Paw’s other Kaywoodie “500” I had used a dark brown undercoat followed by an Oxblood overcoat.  This achieved results that emulated very well the “500” red theme.  The question in my mind after reading Steve’s write-up was the use of black versus dark brown.  I sent Steve an email with that question that resulted in several emails back and forth where Steve responded to more questions raised about how his approach to undercoat staining was different than what I had done and probably, much more effective in creating the affects desired.  Without repeating the full email chain, the process difference that I’m trying out with the Kaywoodie “500” from Steve’s input is to move the undercoating process before the micromesh process and to focus more on the undercoat process of removal of the excess dye.  So, now you know why the presses are on hold!

Therefore, I stop the micromesh process mid-stream and plan to insert Steve’s approach to provide an undercoat and see how it goes!  Regarding the question of the use of black or dark brown for the undercoat, Steve saw no difference in the two.  I understand why now – the point of an undercoat is to darken the grain threads for the most part and in his approach, the undercoat is, in large measure, removed but for these effects.  I decide to apply Fiebing’s Dark Brown Leather Dye as the undercoat.  I assemble on my desktop the needed components.  With spring in full swing here in Sofia, I’m working on my 10th floor Man Cave balcony and enjoying the views while I work.  To begin, after wiping the bowl with alcohol to clean it, I warm the stummel with a hot air gun (inside again for a few minutes).  This warms the briar with the result of opening the grain to be more receptive to the dye.  Then, back on the Man Cave, I use a folded pipe cleaner to paint the aniline dye onto sections of the briar surface.  While still wet, the lit candle ‘flames’ the dye.  The flame combusts the alcohol in the dye leaving behind pigmentation in the grain.  I cycle around the bowl painting and flaming twice to make sure the coverage is thorough.  I then put the stummel aside for the initial undercoat to dry.  The following pictures show the dense appearance of the flamed surface.Turning now to the stem, there is very little chatter on the bit. The lower side pictured in the second picture only has a small button compression that I will address.Deep oxidation is still hanging on especially on the shank side of the stem.  The lighter exposure of the picture helps to show what I can see with the naked eye.To address the lower bit button compression, I use the heating method of expanding the vulcanite, a rubber compound.  With the flame of a Bic lighter, the bit is painted and as the vulcanite heats, the dent hopefully reclaims lost territory.  The result is good.  Only sanding will be necessary.The flat needle file is used to freshen the button and 240 grade paper sands the bit, and the minor chatter is erased.I expand the 240 sanding to the entire stem to address the latent oxidation.  I do not relish the thought of the oxidation emerging during the later polishing stages.  I use a plastic disk I fabricated for this purpose that I pinch up against the stem facing to guard against shouldering the edge of the stem.  The disk works well to maintain a crisp facing.Next, the entire stem is wet sanded with 600 grade paper followed by an application of 000 grade steel wool.  The 3-hole stinger also receives attention from the steel wool.The stem is now ready for the full regimen of micromesh pads beginning with wet sanding using pads 1500 to 2400 and followed by dry sanding with pads 3200 to 4000 and 6000 to 12000.  Between each set of 3 pads, Obsidian oil is applied to condition the stem and to guard against future oxidation setting in.  The Kaywoodie “500” stem looks great. Turning again to the stummel, per Steve’s description I use 430 grade paper to sand off the dried excess undercoat.I combine the sanding with wiping the stummel with a cotton pad wetted with alcohol.  This helps to remove the excess and to allow the grain to come through more.At this point I transition to applying the full regimen of micromesh pads from 1500 to 12000 in 3 pad increments – 1500 to 2400, 3200 to 4000, and 6000 to 12000.  The point of the undercoat is darkening and giving greater definition to the grain.  The progression of the micromesh process shows this to be the case. Next is the overcoat staining with the new red aniline dye I acquired.  I’m hoping to get close to the Kaywoodie “500” red finish hue.  I used Fiebing’s Oxblood as the overcoat last time.  I approach this overcoat stain as if it were the first coat.I begin by heating the stummel with the hot air gun to open the briar’s receptivity to the dye.Next, using a folded pipe cleaner, I paint the red dye on the stummel.  I discover at the first attempt to flame the dye with the lit candle, that there wasn’t enough alcohol content in it to combust.  The application of the dye transitioned into a dye wash – hmm.  I paint the dye on to get a thorough coverage.  I repeat the process once more to make sure all was covered well with the dye. Afterwards, I set the dye aside to dry.  I’m a bit concerned at this point that the red dye may not have enough resonance or depth in it.  It seems to light or pale at this point.I decide to unwrap the finish using Blue Diamond compound and a cotton cloth buffing wheel on the Dremel.  The Dremel is set at about 40% full power.After removing the dye excess my concerns were confirmed.  The new red dye mixture that I used was not ‘grabbed’ by the grain to create much of a red tent over the dark brown undercoating.  I take a quick picture on the black cloth I normally use for the finish shots at the end of the restoration to see what the camera might see.  The finish looks great – the grain looks great, but the color of the Kaywoodie “500” is falling short of expectations. Last time I worked on Paw’s other Kaywoodie “500”, I used an Oxblood over dark brown and it turned out well.  I know my processes have changed up somewhat, but I have a foundation of dark brown undercoating that has been brought down to a darkened grain presentation.  On top of that, the red dye added something… and now, Fiebing’s aniline Oxblood Leather Dye on top of that.  The only thing I do to prepare the surface for the Oxblood is to wipe it well with a cotton pad wetted with alcohol.  Interestingly, almost no dye residue came off after the red wash.  Now using Fiebing’s Oxblood, I apply the dye, flame it, and set the stummel aside to rest for several hours – overnight.  Even at this ‘raw’ state, I can see a marked difference in the dye’s resonance.The next morning, the fire-dyed stummel is ‘unwrapped’ using my normal process, with a felt buffing wheel and Tripoli compound with the Dremel set at the slowest speed.  I take a picture midstream to show the contrast between the flamed shell and the unwrapped briar surface.  The difference is marked.  As the surface is unwrapped, I purge the felt wheel many times during the process by running the felt wheel against the edge of the lapboard I’m working on.  This keeps the felt wheel cleaners and more supple.  The picture below shows the caking on the wheel that happens as the wheel does the plowing. I follow by wiping the stummel with a cotton pad wetted with alcohol.  This lightens the finish some but helps to remove excess dye build up and help to blend the finish.Next, after changing to a cotton cloth buffing wheel set at about 40% full power and after reuniting stem and stummel, Blue Diamond compound is applied to the entire pipe. Tripoli is a coarser abrasive and Blue Diamond is finer, and less abrasive as the fine sanding is completed. After completion, I use a felt cloth rag to buff/clean the pipe of compound dust in preparation for the application of wax.In the homestretch – after changing the cotton cloth buffing wheel and leaving the speed of the Dremel at 40%, carnauba wax is applied to the entire pipe – stem and stummel.  Following this, the pipe is given a rigorous hand buffing with a microfiber cloth to raise the shine.After some twists and turns trying out new processes and a new dye, I’m pleased with the results.  I believe the undercoating advice that Steve provided certainly deepened the signature of the darker grains.  Paw’s Kaywoodie “500” 50C Round Shank Bulldog is looking good with a classy, sharp presentation, and I believe the Oxblood works well to bring out the deeper red tones of the Kaywoodie “500” series.  Paw’s signature remains on the back side of the rim with the shadow of Paw’s penchant for knocking and a reminder of the man he was as ‘2-Page Sam’.  It was a privilege bringing life back to this Kaywoodie “500” for Joe and Hannah and preserving a great grandfather’s legacy to his family. Moreover, Joe’s commissioning of this restoration benefits the Daughters of Bulgaria – women and girls who have been trafficked and sexually exploited. Thanks Joe!, and thanks to all, for joining me!

New Start for an older BBB Best Ambroid Cased Billiard

2 Replies

Blog by Steve Laug

Jeff and I picked up this older BBB Cased Billiard in a group of pipes we purchased not too long ago. It is quite unique. I have worked on a lot of BBB pipes over the years as they are one of my favourite brands and I have quite a few in my collection. This one is a bit different in that it has very little that gives a clue to its age. It is a nice briar with a silver band that is stamped with BBB in the Diamond and Sterling Silver. There were no hallmarks on the band to pin down a date.  It is stamped on the inside of the case with the BBB Diamond logo. The left side of the shank itself is stamped with the BBB Diamond logo. The stem in golden Ambroid and has a bone tenon that screws into the briar shank. It came in a worn black leather covered case lined with black chamois. The case has a brass clasp on the front and brass hinges on the back. It was obviously custom made for this pipe.Jeff opened the case and this was what the pipe that was inside looked like. It was a nice looking classic billiard that is for sure but it was also very dirty. The bowl and shank were a rich medium brown that was very dirty. The stem was golden Ambroid material. The exterior of the bowl was very dirty and had tars and oils ground into the finish and sticky spots on the finish. There was a chip missing on the outer edge at the back of the bowl. The rim top was a mess with lava overflowing out of the thick cake in the bowl. I am sure once it was out of the case it would become clear how dirty it really was.Jeff took it out of the case to have a better look at the condition of the pipe. It was a very classic billiard with a silver band and golden stem. It looked like it would cleanup really well and look great when finished. The finish on the briar bowl looked like it would be great once it was clean. He took some close-up photos of the bowl and rim top. There was a thick cake in the bowl that was hard and uneven. The lava overflowed over the rim top but it looked like the inner edge of the bowl was in good condition. The outer edge had some large nicks and gouges – chunks of briar missing on the back edge. Jeff took photos of the sides of the bowl and heel to show the grain and condition of the finish around the bowl. The pipe has some great grain around the sides. In terms of stamping the only identifying marks on the pipe were the gold BBB Diamond logo on the inside of the case lid, the same stamped on the left side of the shank and again on the silver band. Jeff captured those marks in the next set of photos. The logo on the inside lid of the case was worn and but still readable. Jeff took photos of the stamping on the left side of the shank and the band. He took photos of the stem off the shank/base. The stem has a threaded bone tenon that was filthy with oils and tars. The internals of the pipe were very dirty.Jeff took photos of the stem to show the general condition of the stem shape. The Ambroid stem is well gnawed on both sides around the button. The first photo shows the profile of the straight narrow stem. He took photos of the top and underside of the stem to show the damage and bite marks on both sides up the stem from the button.In 2009 Briar Books Press published a reprint of the 1912 BBB Catalogue No.XX from Adolph Frankau & Co, Ltd.London, E.C. I purchased a copy of the book when it came out and enjoyed reading through it and dreaming about the various pipes that were pictured there. I remembered that there was a section of pipes in the catalogue –Section E called pipes in Cases and it had individually cased pipes with Ambroid stems. I turned to that section in the catalogue and read through the various descriptions and looked at the pictures and sure enough I found this pipe. The only variation was that the one in the drawing had hallmarks on the silver but the rest was identical including the case and stamping on the lid. The top pipe on the right side of the page photo below looks like the one that I am working on.It is described in the title of the page a Best Ambroid Briars Silver Mounted in Cases and available in a variety of sizes. Now I knew the pipe I was working on and that there was at least some variation of it available in the 1912 BBB Catalogue.

It was time to work on it now and do my part of the restoration. I took the leather case from the box that Jeff had shipped to me and brought it to the work table. I opened it up and took photos of the case and the pipe in the case before taking it out and examining it thoroughly to see what I needed to do. You can see the definite similarity between this pipe and the on in the drawing on the top right of the photo above.The pipe looked very clean. The bowl had been reamed back with a PipNet reamer and cleaned up with a Savinelli Fitsall Pipe Knife. The internals of the shank and stem had been cleaned with alcohol, cotton swabs and pipe cleaners. The exterior of the bowl had been scrubbed with a tooth brush and undiluted Murphy’s Oil Soap. The silver band had been cleaned and the tarnish removed. The stem was clean and the damage to the Ambroid was very visible and ready to repair. Jeff had done his usual great job on the clean up. I took photos of the pipe before I started my part of the work. I took some close up photos of the bowl and rim top as well as the stem to show the areas that I would need to address. You can see the that the bowl and rim are very clean. The inner edge of the rim has some damage as do the top and outer edge. There is general darkening to the rim top and scratches and nicks on the surface. The stem is also very clean and the gouges on the top and underside near the button are visible and ready for repair.I took a photo of the stamping on the left side of the shank. I also wanted to show that the band had turned on the shank so that the BBB Diamond was now on the topside so I took a second photo to capture that. I would need to realign the band and glue it in place.I unscrewed the stem from the shank and took photos of the parts. The bone tenon that connects the stem to the shank is visible.I decided to begin my part of the restoration by addressing the issues with the rim top and edges. I topped the bowl with 220 grit sandpaper on the topping board to smooth out the damage on the rim top and the immediate damage on the inner and outer edges. Once I had it smooth I used clear super glue and briar dust to repair the deep gouges in the back outer edge of the bowl. I took a photo of the rim top at this point to show how good the inner edge and top looked. You can also see the repair on the back outer edge of the bowl that still needs to be sanded. I sanded the repair with a folded piece of 220 grit sandpaper to blend it into the surrounding briar and then took a photo of the bowl looking down at the edges. I am happy with the state of the rim and edges at this point in the process. I removed the band from the shank before moving on to  polish the briar with micromesh sanding pads. I sanded the old glue off the shank to make it smooth for the refit. I polished the bowl, rim and shank with 1500-12000 grit micromesh pads wiping it down between pads with a damp cloth. The way in which the rim top colour was blending in with the rest of the briar was perfect and would not need to be stained. I worked some Before & After Restoration Balm into the briar with my fingertips to clean, enliven and preserve the briar. I find that it adds a depth to the polish that I really have come to appreciate. All that remains at this point is to wax and polish the bowl. The bowl looked very good at this point. I was able to preserve the old patina and through polishing blend the rim top into the rest of the finish. It was time to put the band back in place. I used a dental spatula to apply all-purpose white glue to the shank and aligned the band and pressed it in place. I wanted the BBB Diamonds on the shank and band to match as I had seen in photos on line. I wiped away the excess glue with a damp cotton pad.I set the bowl aside and turned to address the issues with the stem. I used a clear CA glue to fill in the deep tooth marks on both sides of the stem and to rebuild the button. I had to layer the glue and let it harden between applications to get a smooth fill on the stem.Once the repairs had cured I used a needle file to cut the sharp edge of the button and to smooth out the repairs.I smoothed out the repairs with a folded piece of 220 grit sandpaper. I started the polishing with a folded piece of 400 grit wet dry sandpaper.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with a cloth containing some Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. I put the bowl and stem back together and carefully buffed the pipe with Blue Diamond polish on the buffing wheel. I gave the bowl and stem multiple coats of Carnauba wax on the buffing wheel and buffed it with a clean buffing pad. I hand buffed the entirety of the pipe with a microfiber cloth. The pipe was alive now and looked great to me. The patina of the older BBB shines through and the repaired Ambroid stem – though far from it pristine beginnings – looks very good.  This pipe is well balanced feels great in my hand. The finished pipe is shown in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. This older BBB Best Ambroid Cased Briar pipe is a beauty and the Ambroid Stem, Sterling Silver Band and old patina briar look stunning together. It is an old BBB pipe so of course it is one that will be staying in my BBB collection. It will be a great addition to my collection of that classic English Brand. Thanks for reading this blog and my reflections on the pipe while I worked on it.

Beginning again – a KB&B Bakelite Blueline Cup and Ball Pipe

Leave a reply

Blog by Steve Laug

Jeff picked up this interesting Cup and Ball or Claw and Ball pipe somewhere along his hunts or in an auction. It is quite unique. I have worked on a lot of KB&B pipes but never one like this. It is stamp on the inside of the case with the KB&B Cloverleaf and Bakelite in the centre. Underneath it appears to read Blueline. The gold band on the shank end is also stamped with the KB&B Cloverleaf as well as what looks like 12K Gold Plate. Both the base of the pipe and the stem are Bakelite. The stem has a bone tenon that screws into the Bakelite shank. It came in a black leather covered case lined with blue velvet fabric. The only marking on the case was what I mentioned above. The case has a brass clasp on the front and brass hinges on the back. It was obviously custom made for this pipe.Jeff opened the case and this was what the pipe that was inside looked like. It was a very unique looking pipe that is for sure but it was also very dirty. The base, shank and stem were rich red coloured Bakelite. The exterior of the bowl was very dirty and had tars and oils ground into the finish and sticky spots on the finish. Looking at the top of the bowl you can see the cake and how much lava had overflowed onto the rim top. I am sure once it was out of the case it would become clear how dirty it really was.Jeff took it out of the case to have a better look at the condition of the pipe. It was a very interesting looking rendition of a Ball and Cup pipe – at least that is what I would call it. It looked like it would cleanup really well and look great when finished. The hardwood bowl (cherry or maple) had some colour from either being filthy or from age. Cleaning would reveal the facts! He took some close-up photos of the bowl and rim top. There was a very thick cake in the bowl that was hard and uneven and had lots of flakes of tobacco debris stuck to the walls. The lava overflowed down the outside of the ball on several sides. The edges of the bowl looked to be in pretty good condition at this point. Jeff took photos of the sides of the bowl to show the grain and condition of the finish around the bowl. These photos also lead me to conclude that the bowl is not briar… perhaps Cherry or Maple.In terms of stamping the only identifying marks on the pipe were those on the case on the gold band on the shank. Jeff captured those marks in the next set of photos. The logo on the inside lid of the case was worn and dirty so he included two photos of that. I also found a similar lid logo online and have included it as well for comparison sake. Jeff took photos of the KB&B Cloverleaf and the 12K Gold Plate stamp on the band.He took photos of the ball and the stem off the shank/base. The ball and the stem both are threaded and are screwed into the base. It was filthy with oils and tars. The internals of the pipe were in as bad a condition as the inside of the bowl and airway.Jeff took photos of the stem to show the general condition of the stem shape. The curve is graceful and the curve great. The photo shows the profile of the stem. He took photos of the top and underside of the stem to show the damage and bite and scratch marks on both sides up the stem from the button.I remembered that one of the contributors to rebornpipes, Troy Wilburn had done a lot of work on older KB&B pipes so I turned to one of his blogs on rebornpipes on a Blueline Billiard that he restored (https://rebornpipes.com/tag/kbb-blue-line-pipes-with-bakelite-stems/). As expected Troy had done a great job digging into the Blueline brand and potential dates. I quote from his blog the following sections.

I was thinking after some initial research that these pipes were from around 1910 – early 1920s. Seems it’s a little older than I thought. I got this info from a Kaywoodie and early KBB collector who has had several Blue Lines.

Your pipe is made by Kaufman Brothers and Bondy, or KB&B, which later (1915) created the Kaywoodie line we all know. But this pipe is Pre-Kaywoodie, as they were making pipes under the KB&B branding from about 1900 to 1914. Bakelite was invented in 1907, so this pipe was likely made from 1908 to 1914, as the Bakelite was quite the technological wonder of the time, and was used in many products (still in use today). These “Blue Line Bakelite” pipes are rare pieces, seldom seen.”

Having seen the before pictures on this pipe I was looking forward to what it would look like when I unpacked the most recent box Jeff sent to me. The pipe was present in the box and I took it out of the box to see what work awaited me when I removed it from the case. I put the case on my desk and opened it to see what was there. I opened the case and took a photo of the pipe inside.I was astonished to see how clean the pipe was. The bowl clean and the Bakelite base and stem looked very good. Even the gold band looked better. Now it was time to take it out of the case and have a look at it up close and personal. I took photos of the pipe as I saw it. Jeff had done an incredible job in cleaning up this pipe. He had reamed the bowl with a PipNet Pipe reamer and cleaned up the remaining debris with a Savinelli Fitsall Pipe Knife. He also scraped the thick lava on the rim top. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime on the bowl and rim. He cleaned out the interior of the bowl base and stem with pipe cleaners, cotton swabs and alcohol until they came out clean. The rim top looked incredible when you compare it with where it started. There is some slight darkening on the inside edge of the bowl. He cleaned the base and stem with Soft Scrub to remove the grime on the exterior and cleaned out the airway with alcohol, cotton swabs and pipe cleaners. I included a photo of the KB&B Cloverleaf on the gold plated band.I unscrewed the bowl and the stem from the base and took photos of the parts. The bowl and stem both had threaded connectors. The bowl was metal and the stem was bone.I stripped the spotty finish off the bowl with acetone. I know for some this is a no-no for old pipes but honestly this finish was very rough. I would restain it as close to the original aniline as I could but there was damage that needed to remove the stain and finish to address. I followed that by sanding the bowl with a medium and a fine grit sanding sponge. The bowl was looking better and the dark spots turned out to be oils and not burn marks! Whew! I polished the bowl with micromesh sanding pads – dry sanding with 1500-12000 grit pads and wiping the bowl down after each pad with a damp cloth. Note the developing shine on the wood. I went through my various stains and chose a Tan aniline stain for the bowl. It is a nice coloured stain that is close to what was original and will give me some coverage over some of the dark spots on the sides of the bowl. I applied the stain and flamed it with a lighter. The flaming burns off the alcohol and sets the stain in the wood. I repeated the process until I was happy with the coverage.I set the bowl aside to let the stain cure and turned my attention to the base. The band was loose so I removed it for the first round of pads. I polished the Bakelite with micromesh sanding pads to remove the scratching and bring out a shine. I dry sanded with 1500-12000 grit pads and wiped it down with a cloth I use that has Obsidian Oil impregnated in the fibres. It works well to remove the dust. I paused the polishing to glue the gold band on the shank end. I put some white all-purpose glue on the Bakelite and pressed the band in place on the shank. I wiped the excess glue off with a damp cloth. I let the glue dry for a short time.When it had set I continued polishing with the micromesh pads. I set the base aside and went back to the bowl. I buffed out the newly stained bowl with Blue Diamond to bring out a shine. The colour is opaque enough to hide the dark spots and transparent enough to show some grain in the sunlight. I like it!I rubbed Before & After Restoration Balm into the wood with my fingertips to clean, enliven and preserve the newly stained bowl. I find that it adds a depth to the polish that I really have come to appreciate. All that remains at this point is to wax and polish the bowl. With the bowl and the base finished it was time to put them back together. I would still need to buff and wax both but the project was coming to an end. All that remained was to finish the stem work. I set the base and bowl aside and turned to address the issues with the stem. I used a clear CA glue to fill in the gouges across the stem from the button forward an inch on both sides. I also filled in the deep tooth marks on both at the same time.I smoothed out the repairs with a folded piece of 220 grit sandpaper. I started the polishing with a folded piece of 400 grit wet dry sandpaper.I rubbed the stem down with Denicare Mouthpiece Polish. It is a gritty, red paste with the consistency of red Tripoli. I find that it works well to polish out scratches and light marks in the surface of the stem. I polished it off with a cotton pad to raise the shine.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with a cloth containing some Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. I gave it a coat of Briarville’s No Oxy Oil to preserve and protect it. I put the hardwood bowl and Bakelite Base stem back together again and carefully buffed it with Blue Diamond polish on the buffing wheel. I gave the bowl, base and stem multiple coats of Carnauba wax on the buffing wheel. I hand buffed the entirety of the pipe with a microfiber cloth. The pipe was alive now and looked great to me. It has a great feel in the hand that is very tactile and the colouring on the bowl should develop more deeply as the pipe is smoked. The finished pipe is shown in the photos below. The dimensions of the pipe are Length: 5 1/2 inches, Height: 2 1/4 inches, Outside diameter of the bowl: 1 1/4 inches, Chamber diameter: 7/8 of an inch. This older KB&B Blueline Cup and Ball pipe is a beauty and the Bakelite looks great with the newly stained bowl. It is one of those old timers that will be staying in my KB&B collection. It will be a great addition to my collection of old pipes. Thanks for reading this blog and my reflections on the pipe while I worked on it.

Operation Rescue – “My Dog Ate my Ser Jacopo L1 Billiard!”

7 Replies

Blog by Steve Laug

When Jeff showed me the next pipe on the table we went back and forth about buying it or just leaving it with the seller. It was a really nice Ser Jacopo L1 Billiard at some point in its life but that time had passed. It had literally become a chew toy for someone’s dog. The bowl was in very rough shape and had deep tooth gouges around the bowl with chunks of briar missing on the rim and top. The bowl was really damaged to the point of being questionable. The shank interestingly was free of bite marks and the stem had less bite marks than some of the stems I have worked on from pipemen who chew their stems. For me the question was whether or not I wanted to work on it. There was no doubt that the pipe would be a challenge but was it a challenge I wanted to take on. That was the question we weighed before moving ahead with the buy.

After spending time talking about it we decided to pick up the pipe and see what I could do with it. When Jeff got it the story became even sadder!  The bowl had amazing straight grain around the sides and it appeared to have been barely smoked. It looked as if maybe a bowl or two had been enjoyed before the dog got a hold of the pipe and did the massive damage that showed when we saw it. The bowl had some darkening but there was no cake in the bowl. It smelled smoky but otherwise was very clean. Jeff would still clean up the pipe before he sent it on to me that way I would be able to just pick it up and see what I could do with it. Jeff took the following photos before he started his cleanup work on the pipe. Just look at the damage! Oh my; the pipeman or woman must have just wept after the initial shock or anger when he or she saw the pipe dangling from the dog’s mouth. He took close-up photos of the bowl and rim top from various angles to capture the gnawing damage to the bowl and rim top edges. You can see the large bite marks and chunks of briar missing on both the inner and outer edges. The largest chunk is on the front of the bowl and the inner edges damage is on the right side. You can also see the damage to the sides of the bowl. Jeff took photos of the sides and heel of the bowl to show the both the extent of the damage to the bowl and the amazing grain around the bowl. It really is a shame that this poor pipe suffered this fate. Jeff took photos of the stamping on sides of the bowl. On the left side it reads Ser Jacopo over Fatta A Mano over In Italia. On the right side it reads L1 in a circle Per Aspera Ad Aspera. On De Divina Proportione. All the stampings are very readable and clear. He took a photo of the inlays on the tapered stem top. The silver J with an I and a circle. The next two photos show the top and underside of the stem. Notice the few tooth marks on both sides. It is not as bad as it could be. I wanted to know a bit more about the pipe in hand. I knew a little of the history of the brand but I wanted to understand the stamping on the shank sides and underside so I turned first to the Pipephil website (http://www.pipephil.eu/logos/en/logo-s5.html). Interestingly the first pipe they had a photo of was similar to the one that I had. It is stamped similarly on the left side of the shank with the Ser Jacopo over Fatta a Mano but the one I have also was stamped In Italia under that. The right side of mine is stamped with the L1 in a circle and the Per Aspera Ad Astra followed that. Mine also was stamped on the underside of the shank and read: De Divina Proportione. The one I am working on also had a band on the shank and the stem stamp was different as well. I also learned the L1 stamp stood for a pipe with acceptable grain. I have included a screen capture of the  pertinent information.Once I had that material digested a bit I turned to Pipedia to understand more about the stamping on the pipe (https://pipedia.org/wiki/Ser_Jacopo). I am including the information on that below. The standard nomenclature found on Ser Jacopo pipes is as follows: Ser Jacopo Fatta A Mano In Italia Per Aspera Ad Astra.

Fatta A Mano translates to “Made By Hand”. Per Aspera Ad Astra is a Latin phrase found on Ser Jacopo pipes and is the Ser Jacopo motto. It translates to “To the Stars Through Travails”, meaning that success comes through hard work. In the Summer 1997 Pipes and Tobaccos article Giancarlo Guidi translated this as “through a difficult way until the stars are reached”.

All that remained was to find out what the De Divina Proportione on the underside of the shank meant. I turned to wikipedia (https://en.wikipedia.org/wiki/Divina_proportione) for what I assumed referred to Divine Proportion or the Golden Ratio. I quote from there a good summary.

Divina proportione (15th century Italian for Divine proportion), later also called De divina proportione (converting the Italian title into a Latin one) is a book on mathematics written by Luca Pacioli and illustrated by Leonardo da Vinci, composed around 1498 in Milan and first printed in 1509.[1] Its subject was mathematical proportions (the title refers to the golden ratio) and their applications to geometry, to visual art through perspective, and to architecture. The clarity of the written material and Leonardo’s excellent diagrams helped the book to achieve an impact beyond mathematical circles, popularizing contemporary geometric concepts and images.

Now I had a clear idea of the meaning of the stamping. The Golden Ratio refers to the mathematical proportions of this particular pipe fitting that Ratio. It is seriously a beautiful pipe and now I am even sadder at the damage that was done. That motivates me to try to bring it back to some semblance of beauty.

Now it was time to look at it up close and personal. Jeff had done an amazing job in removing all debris and bits of broken briar from the finish. He had done a quick reaming of the bowl with a Savinelli Fitsall Pipe Knife. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime the grime and dirt on the finish so the pipe was clean – damaged but clean. He cleaned out the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol until they came out clean. The rim top looked quite daunting with the missing chunks of briar but it too was clean. He cleaned the stem with Soft Scrub to remove the grime on the exterior and cleaned out the airway with alcohol, cotton swabs and pipe cleaners. I took some photos of the pipe as I saw it when I brought it to the work table. To show how the rim top and stem looked at this point I took a close-up photo of the rim and stem. The bowl was clean and the damage to the inner edge and the rim top was very visible. It was a mess! The black acrylic stem was saved from major dog chomping. There are just a few tooth marks on both sides of the stem that could be addressed fairly easily.I removed the stem from the bowl and took photos of the parts. I chose the left side of the bowl as really both sides were equally damaged. This is truly a sad sight to see as the great grain on the bowl shows up nicely under the damage.I had been thinking about what to do with the finish since first seeing the photos. I had decided I would rusticate it but was undecided as to what extent I would go in the process. I wanted to retain the original shape and intent of the pipe while working out the damages. I started by using three different burrs on the Dremel – a ball, a cone and cylinder. Each one gives a slightly different finish. I worked them one after another to seek to blend in the tooth marks as much as possible. I also decided to rusticate the worst areas – the base and part way up each side of the bowl and the entire bowl front. The photos show this first step. I decided to let that rustication pattern sit with me for awhile and not add more to it. I just wanted to think about it for a  while. I decided then to patch the bite marks in the upper part of each side and the entire back of the bowl. I also wanted to repair as much of the rim top and edge damage as I could. I used clear super glue and briar dust to patch the many tooth marks around the bowl. The photos show the freckled sides. I built up the damaged front outer edge and the deep marks on the top of the rim with super glue and briar dust. These took some layering to do the job. I looked over the rustication some more and was not completely satisfied with the coverage of the existing rustication or the distance I came around the sides of the bowl. I decided to use a tool that a reader of rebornpipes made for me for rusticating. You can see it in the photos. It is essential a group nails bound together in a handle and with a clamp to give me multiple points to rusticate with. The way it works is to press it into the briar and twist it. You move across the briar until it is “randomly” covered. Once I was happy with the coverage I knock off the debris left behind with a brass bristly brush. I like to knock it down and smooth it out to give it an old leather like look to the rustication. I left the rustication and turned to address the damage to the rim top. I topped the rim with 220 grit sandpaper on the topping board. Once it was smoother and flatter I filled in the divots and holes in the rim top and edges with briar dust and super glue once more. Once I finished I topped it once more to smooth out the repaired areas.With that finished for the moment I turned to sanding the smooth portions of the bowl. I used my Dremel and sanding drum to flatten out the repaired areas first. I followed up by sanding them with 220 grit sandpaper. The photos below show the bowl at this point in the process. Note that there was no damage to the shank so I left it as is and would match the stain to that once I stained the repaired area. I was pretty happy with the way it was looking. I was ready to stain the undercoat on the bowl. I decided to use a black aniline stain for the rusticated part of the bowl and for the undercoat on the smooth sides and rim top. Black does a great job hiding the kind of repairs that I had to do with this briar. I applied the stain and flamed with a lighter. I repeated the process to ensure the coverage was thorough. I flamed it again and set it aside to dry while I had some dinner.I took photos of the bowl at this point to show the coverage of the black stain on the rustication and the undercoat on the smooth areas. After dinner I wiped down the smooth areas with isopropyl alcohol on a cotton pad to make them more transparent and show the grain. I then gave the smooth areas a coat of Mahogany stain using my stain pens to get into the transition areas and control the flow better. The combination of the black undercoat and the Mahogany matched the original shank colour! When that coat of stain had cured I polished the smooth portions of the bowl with micromesh sanding pads. One of the pains of this process is all the flaws show up in the initial sanding. You can see my repairs in some spots but hopefully they bill disappear a bit in the polishing. I was really happy with the right side of the bowl. The repairs virtually disappeared in the staining and sanding. I worked on the left side a little more. I sanded the offending areas of the transition with 400 grit wet dry sandpaper and restained the area. I worked through all of the micromesh pads another time on that area. I was happy with the finished looked at this point. I rubbed the finish down with Before & After Restoration Balm. I worked it into the smooth areas on the bowl and rim top with my fingertips and the rusticated areas with a horsehair shoe brush. The product cleans, protects and enlivens the briar. I let it sit for about 30 minutes and buffed it off with a cotton cloth. The photos below show the bowl at this point… it is a far cry from the dog eaten bowl that I started with — at least I think it is ;). I set the bowl aside and turned to the stem to address the issues that were on the top and underside. I filled in the tooth marks on the stem with clear super glue. I generally overfill them a bit so that it takes into account the shrinkage that occurs as the repair cures.Once the repairs had cured I sanded them smooth to start to blend them in with the surround acrylic of the stem. I sanded the repairs on both sides with a folded piece of 220 sandpaper and started polishing with 400 grit wet dry sandpaper.I rubbed the stem down with Denicare Mouthpiece Polish – a red gritty paste a lot like Tripoli to polish it after the 400 grit sandpaper. I rub it on with my fingertips and work it into the vulcanite and buff it off with a cloth. It does a great job before I polish it further with the micromesh pads.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped the stem down after each sanding pad with a cloth containing some Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. The next steps in this restoration were ones that I have been looking forward to. I was glad to reunite the bowl and stem and see what the finished pipe looked like. I polished the silver with a jeweler’s cloth and buffed the bowl and the stem with Blue Diamond on the buffing wheel. I used a light touch on the rusticated portion as I did not want to fill in the rustication with the product. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax. I carefully buffed the entire pipe with a clean buffing pad to raise the shine. I finished buffing with a microfiber cloth to deepen the shine. The finished pipe looks a lot better than dog chewed pipe that I started with. I am happy with the finished look at this point. While the repairs to the smooth areas show a bit they are smooth. The leather like rustication works well with the finish on the bowl in my opinion. The finished Ser Jacopo L1 Billiard is shown in the photos below. The dimensions of the pipe are Length: 6 ½ inches, Height: 2 ¼ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. This should be a great pipe once it is broken in. The rustication on the base and front give it a very tactile feel that should only be better as it heats up during a smoke. This one will go on the rebornpipes store shortly. If you are interested in it let me know. Thanks for reading this blog and my reflections on the pipe while I worked on it.

 

 

Bringing to Life a Unique Kaywoodie Natural Burl 33 – Another Legacy Pipe of a Great Grandfather

3 Replies

Blog by Dal Stanton

This is the second of 3 of Paw’s pipes that Joe sent to me from Athens, Greece, where he and his wife, Hannah, live and work.  Paw is Hannah’s great grandfather who left behind several pipes that Joe has asked me to restore for the family.  Paw, also known as, ‘2-Page Sam’ by those who knew him as a salesman of over 40 years of the tobacco giant, Brown & Williamson Tobacco, Corp, has a fascinating story that was described in an article in B&W’s company magazine that I included in the write up of Paw’s Medico Apollo Brylon, which I just completed that turned out well (See: Another Legacy Pipe of a Great-Grandfather: Challenges Working with ‘Brylon’ on a Medico Apollo).  Next, two Kaywoodies remain to be restored – a Kaywoodie “500” and the one on my worktable now, a Kaywoodie Natural Burl 33.  Here are pictures to take a closer look. The nomenclature is on the underside of the shank’s smooth briar panel with ‘KAYWOODIE’ (as most of it is not legible as the upper half of ‘Kaywoodie’ bleeds into the craggy rusticated landscape) [over] ‘Natural Burl’ in fancy cursive script. To the left of the nomenclature is stamped the Kaywoodie shape number of 33.  In Pipedia’s listings of Kaywoodie shape numbers, 33 is listed as: “Large apple, rounded top” that was used as a shape designator from 1937 to 1972.The dating indicators of this Kaywoodie are good.  The Natural Burl has a 4-holed stinger which were phased out at the end of the 1950s, though they still show up some in the 60s according to Pipephil.eu’s discussion about Kaywoodie’s stinger evolution.  The inlaid white shamrock also points to an earlier period.I found nothing specific in Pipedia or Pipephil.eu about Kaywoodie’s ‘Natural Burl’ line.  Expanding my search, I did find very helpful anecdotal information in a February, 2013, thread by ‘kwguy’ on a Kaywoodie discussion group on Tapatalk.com:

Natural Burls are in the catalogs from 1957 to 1962. They were $4.00 when they first came out and $5.00 by the time they were discontinued.  They were basically a stained version of the Coral White Briar, which also debuted in 1957.  The overall rough texture was described in the catalogs as having a rough texture like the outside of the burl.  The rough texture in theory would create more surface area for a cooler feeling bowl.  Carving of this type was done on bowls of less desirable grain and with excessive surface imperfections.  On the lower side of the quality scale, Natural Burls would have had the white cloverleaf.  There may have been the occasional higher grade pipe that was downgraded during production and hence would have the round logo, but I think you’ll mostly see them with the white logos.

Based upon the information of this thread, the Natural Burl Apple before me dates from 1957 to 1962, when they were featured in Kaywoodie catalogs. I looked for a catalog during this period online, but unfortunately, I was unable to find one.  The rusticated or carved surface theoretically provides a cooler feeling bowl.  This pipe fits Sam’s low budget approach to his pipes.  When the Natural Burl Apple first hit the market, it was in a working man’s modest budget range, $4!  I’m hopeful that after I’ve completed working on Paw’s vintage Kaywoodie it will look like a million bucks!

The above thread from ‘kwguy’ also mentions that the ‘Natural Burl’ line was featured in Kaywoodie catalogs from 1957 to 1962.  There are Kaywoodie catalogs and adds referenced on Pipedia and the Chris Keene Directory of Pictures, but I could find nothing in these ‘go-to’ places for catalogs or listing between 57 and 62.  Emails to Steve and rebornpipes contributor, Al Jones, also came up empty.  However, Al encouraged me to reach out to Bill Feuerbach, the current president of S.M. Frank with Kaywoodie production in New York.  Al said that Bill had always been helpful and had seemed to enjoy providing info.  Nothing like going to the top of the pipe food chain!  I sent a note to Bill through the S.M. Frank website as well as to the ‘kwguy’ in the Natural Burl thread with the hope of getting a response and perhaps a historical Natural Burl add!

Al’s suggestion to me paid off!  In a few days I received a response from Bill Feuerbach, president of S.M. Frank since taking over the role from his father in 1990 as the fourth generation of Feuerbachs overseeing the company.  Bill’s note to me:

Dal 

I’d love to be able to help you out with that. I’ve looked through what I have at the shop and most of those catalogs are later 60’s to later 70’s.  I’m sure I’ll have those older catalogs from that range at home.  I’ll try and check tonight.

Best regards

Bill

After arriving home that night, Bill sent an additional note that he hadn’t found anything at his home and would redouble his efforts the following day at the shop to find the sought after ’57 to 62’ catalog pages.  Then, this note came in and the treasure hunt ended with success!

Dal

Success!!  I found the catalogs at home.  They were in a storage tub in the downstairs closet. Funny I don’t remember putting them there. It’s probably been 4 years since I referenced them. It is hell getting old, CRS is kicking in.

Anyway, I’ve attached three images from the 1958, 1960 and 1962 catalogs.  I was only using my phone to take pictures and it was difficult not to get any flash or glare.  Are they ok?  You can tell the year by the retail prices for the Natural Burl.

1958- $4.00

1960- $5.00

1962- $5.95

Let me know when you’ve posted this and the link. I’d like to take a look.  If you have any other questions let me know. If in the future you need other images from the catalogs, let me know.

Best regards

Bill

The images Bill sent were great depicting the Kaywoodie presentation of the Natural Burl line.  Both the 1960 and 1962 pages, second and third below, showcase the Large Apple on my worktable.  The pictures and descriptions are great helping to wrap Paw’s pipe in its historical context! I appreciated the help of Bill Feuerbach, president of the S. M. Frank Co. & Inc. based in New Windsor, New York.  The Frank website not only showcases the Kaywoodie, Yello-Bole and Medico brand lines, but has other interesting information as well.  In my email response to Bill, I offered to digitize the ‘treasure tubs’ of Kaywoodie catalogs and adds if I only lived a bit closer to his neighborhood!  Oh my….

As I was waiting for word from Bill before he found the catalogs, I reread the Pipedia article on the S.M Frank Co. and discovered at the bottom of the article a reference to Brian Levine’s interview of Bill on the Pipes Magazine Radio Show.  I tuned in to learn more about Bill and the Kaywoodie name.  I was interested to hear in the interview that not only is Bill the CEO of the company, but he is an accomplished freehand pipe maker himself, likes single malts and owns and enjoys pipes in his rotation other than Kaywoodies!  It was a great interview and I encourage readers to tune in too!

The name for this Kaywoodie series, ‘Natural Burl’, harkens back to a pipe’s origins – or at least its bowl.  The Natural Burl adds above from Bill describe the ‘rugged, weather-carved briar’ that breathes more because of the increased surface of the bowl.  Briar comes from a bush-like plant that grows in arid lands.  The Kaywoodie motif focuses on the rough state of the burl in its natural form sporting rusticated or carved bowls to emulate a natural harvested burl.  The burl is the base of the briar bush that is cut into blocks, each becoming the raw material for fashioning each unique bowl. I found this example online of the burl texture which looks very much like the pipe on my worktable! This interesting information was added about the process at the WorthPoint site:

The mother of briar is Erica Arborea, an evergreen bush / tree, that grows in all forests of the Mediterranean area, preferring acid soils (Cyprus, Greece, Italy, Spain, France, Portugal, Morocco, Algeria- these are the countries where it is found). The bush has a typical height of 3 – 12 feet. But not the visible parts are the wanted ones, the ball-like roots are the pipe makers desire. These are the raw material for the briar wood, which is cut in blocks (plateaux and ebauchons) by real specialists. After a long process of boiling them in clear water and drying periods, these briar blocks will be ready for the experienced hands of a pipe maker.

With a deepened understanding and appreciation for Paw’s Kaywoodie on my worktable, I look more closely at the issues it brings from its years of service. As one would expect, the craggy Burl bowl is full of grime.  The chamber has thickening cake as you go down toward the floor.  This needs to be cleaned out as well to inspect the chamber wall and to give the briar a fresh start. The rim has evidences of Sam’s penchant for knocking the stummel on the back side of the rim.  It is worn and tapers away from the chamber. The rim was fashioned to be somewhat rough complementing the craggy bowl motif, but there is a large chip or divot out of the rim that will need to be filled and then blended. The bowl itself, along with the rim, is faded and skinned up.  I suspect that the original finish bent toward a light brown, but it is now thin and will need refreshing with new dye to blend the rim and bowl.  The 1962 add above describes a ‘2-tone brown finish’ characterizing the ‘Natural Burl’ line.  This is helpful information that hints at the depth of the final finish.The stem is in rough shape.  The oxidation is thick and deep.  The bit has calcium caked on it and some lower tooth compressions – not as bad as I’ve seen on Paw’s previous pipes! The stem orientation is also over-clocked which is a normal phenomenon with Kaywoodie screw in stems that happens over years of use with repeated loosening and tightening.  This will need to be adjusted as well. I begin the restoration of Paw’s Kaywoodie Natural Burl Large Apple by addressing the severe oxidation in the stem.  Before placing the stem in a soak of Before & After Deoxidizer, I get a head-start on removing the oxidation by pre-sanding the stem.  I use both 240 grade sanding paper and 000 grade steel wool to sand the stem to remove as much oxidation and caked calcium as possible.  The nickel 4-hole stinger also is cleaned up with the steel wool.After the sanding, the stem joins other pipes in the queue in a soak of Before & After Deoxidizer. After a few hours, the Kaywoodie’s stem is extracted from the Deoxidizer and after draining, I squeegee the liquid off the stem with my fingers.  I then run a pipe cleaner wetted with isopropyl 95% through the airway to clear the Deoxidizer.  Using a cotton pad and alcohol, the stem is wiped to remove the raised oxidation resulting from the soak.After cleaning the stem, paraffin oil is applied to help condition the vulcanite.  I put the stem aside to absorb the oil.  The stem looks great compared to where it started. It’s cleaning up nicely.Next, I turn the attention to the stummel.  I begin by reaming the Kaywoodie’s chamber to remove the cake.  Using the Pipnet Reaming Kit, I use two of the four blade heads available in the Kit.  I don’t know how long this cake has been waiting to be removed, but it is as hard as a brick.  I’m careful not to force the blades beyond their torque endurance level – simply allowing the scraping action to wear away the brick cake.  When both blades do what they can, the Savinelli Fitsall Tool continues the scraping of the chamber walls. Finally, to remove the last remaining carbon remnants, a 240 grade sanding paper is wrapped around a Sharpie Pen to sand the chamber getting down to fresh briar. After wiping the chamber with a cotton pad wetted with alcohol, and inspection reveals a perfectly healthy chamber.  The picture on the 10th floor Man Cave balcony where I’m working, does not allow a very good picture of the chamber, but it looks good.  Moving on.Next, using undiluted Murphy’s Oil Soap, I go to work on the wonderfully craggy but grime-filled surface of the Natural Burl bowl.  I use a cotton pad a bit, but transfer to using a bristled toothbrush which gets into the nooks and crannies of the landscape much more effectively.Next, after transferring the bowl to the kitchen sink, I continue to clean the surface and use shank brushes and liquid anti-oil dish soap and warm water to work on the internals.  After rinsing thoroughly, back on the worktable I take some pictures of the results.  The cleaning has totally removed what was left of the old finish – not unexpected.  The cleaning reveals some white fills on the right side of the stummel which are fully embraced in the craggy landscape cover and seem to be solid after testing them with a sharp dental probe.Next, I focus again on the internal cleaning using pipe cleaners and cotton buds wetted with isopropyl 95%.  Cleaning Kaywoodie pipes tends not to be easy.  Working through the threaded metal shank facing makes access to the mortise difficult.  Along with pipe cleaners and buds, the full arsenal added the use of shank brushes, and a dental spoon to scrape the mortise walls.  After quite a bit of time and effort, the buds start to emerge lighter and a cease fire is called. I’ll continue the cleaning later with a kosher salt and alcohol soak to work through the night to further clean and freshen the internals of the Kaywoodie stummel.Turning now to the rim, the next step is to fill the divot, or perhaps, the crater on the rim.  I go along with the ‘rough’ motif of this Kaywoodie Natural Burl.  The rim is rough and the only repair I plan for the stummel is this divot.  The damage of Paw’s knocking will remain – it simply adds to the rough rustic look and will be a remembrance of Paw when it is put into service by the family.I place a small mound of briar dust on the mixing palette that I’ve covered with scotch tape for ease of cleaning.  Next to the briar dust a small amount of BCI Extra Thick CA glue is puddled.Using the toothpick, briar dust is pulled into the glue and mixed as it is added.  As more is added, the resulting briar dust putty thickens.  When it reaches the thickness of molasses, with the toothpick the putty is troweled to fill the rim divot.With the briar putty applied, I place the stummel aside for several hours for the putty to cure.Turning now to the stem, the upper bit is in good shape after the ‘pre-sanding’ that was done before putting the stem into the Deoxidizer.  The lower bit, pictured below, has some compressions and a button bite compression that need addressing.I start by using the heating method with a Bic lighter.  Using the flame of a Bic lighter, I paint the bit using a back and forth motion heating the vulcanite.  As the vulcanite heats, it also expands to regain the disposition of the stem before the compressions were made by Paw.  The picture below is after the heating and the process has helped the bit compressions so that only sanding should be needed to remove the damage.  However, the button is still in need of additional steps.To fill the button lip bite, after wiping the area with alcohol to clean it, I spot drop black CA glue on the compression and put the stem aside for the patch to cure.The patch on the rim is now ready for filing.  I use both the flat and half-rounded needle files to remove the excess putty and to shape the internal curve of the rim. I put a stop on sanding and further cleaning the rim because the hour is late, and through the night I want to use a kosher salt and alcohol soak to advance the cleaning of the internals of the stummel.  I first fashion a cotton ball into a ‘wick’ by pulling and twisting it.  It is then inserted down the mortise into the airway with the help of a stiff wire. The wick helps to draw out the latent residue of tars and oils.The bowl is then filled with kosher salt, which leaves no aftertaste as with regular iodized salt.  After placing it in the egg carton to keep it stable, I then fill the chamber with isopropyl 95% until it surfaces over the salt. After a few minutes, as the alcohol is drawn into the stummel, the alcohol is topped off and it is set aside to work through the night. The next morning, the salt and wick are slightly soiled which hopefully means that the internals are already clean from earlier. After dumping the expended salt and wiping the bowl with a paper towel, I blow through the mortise to make sure all the salt crystals have been dislodged. To make sure that the internals are clean, and nothing has been left behind after the soak, I use only one pipe cleaner and cotton bud as confirmation of the cleaning. Moving on.I return now to the rim.  I plan to apply a fresh color to the stummel and the only preparation for applying the new stain to the stummel is on the rim.  I plan to leave it in the rough motif of the Natural Burl line, but I want the rim cleaned.  I lightly sand the internal rim edge as well as lightly around the rough external rim edge as it transitions into the Burl landscape.  I’m looking for ‘rough’ and ‘rustic’ but ‘fresh’ to give this unique Kaywoodie a fresh start.I follow the 240 paper with 600 grade paper with the same approach – keep the rustic but refresh the rim.Before moving to the next step, I notice that the nickel shank facing after the cleaning had not been spruced up.  A quick revolution of 000 steel wool takes care of this.  This is the only bling this Kaywoodie has and I’m making the most of it!As I think about applying a fresh color to Paw’s Kaywoodie, I have only one picture of another Natural Burl online and it is no help in hinting at the original 2-toned brown coloring Kaywoodie used.  The best clue I have is on Paw’s pipe. The smooth briar panel on the underside of the shank holding the nomenclature holds a clue.  To guard the stamping on the panel I’ve not sanded it – only cleaned with the rest of the stummel.  I’m guessing that the coloring of the panel leans toward a light brown.  I’m thinking that Kaywoodie’s approach was straightforward with this less expensive line of pipes.  Yet, the craggy surface now is so dry and bare, showing pristine briar, that applying even a light brown dye will probably darken considerably as the thirsty briar drinks it in.Looking at the craggy landscape in the picture above brings the next question in my mind about applying a new finish.  My normal way of staining with aniline dye is to flame it to combust the alcohol which encourages a deeper embrace of the dye by the briar grain.  My normal follow-up to this is then to apply compounds to remove the crusting the combustion creates and to further shine the surface with the fine abrasives of Tripoli and Blue Diamond compounds.  The roughness of this stummel causes me to question my normal approach.  My concern is that if compounds are used on this craggy rough surface, I will forever be trying to clean out the compound residue lodged in the rough surface!  I think I can utilize buffing wheels on the Dremel without too much problem, but without compounds.  I decide in the end to apply a dye wash instead of flaming the dye because of this concern.

After wiping the stummel down with a cloth and alcohol to clean it the best I could, the stummel is heated with the hot air gun to open the briar.Then, with the use of a folded pipe cleaner, the surface is painted with Fiebing’s Light Brown Leather Dye.  I make sure the dye is getting into all the cracks, crevasses, nooks and crannies.  The rim also receives the dye.After the dye is applied, the stummel is set aside to rest for several hours before continuing with the next steps of finishing.  This ‘rest’ helps the new dye to stabilize in the briar.Turning back to the stem, the patch applied to the lower button lip is cured and I use a flat needle file to remove the excess patch material and to shape and refresh the button lip.  I also file the bit area to remove any residual tooth compression.Flipping over to the upper bit, I file residual compressions as well as refresh the button lip.  Refreshing the button lip is helpful to allow a better ‘hang’ grip of the pipe without biting and clenching, and extreme chewing!Continuing now with 240 grade sanding paper on the upper side, the file scratches are removed, and the button is smoothed further.  The same is done on the lower bit and to further blend the button patch.   I expand the 240 sanding to the entire stem to make sure that residual oxidation has been addressed. Following the 240 sanding, I wet sand the entire stem with 600 grade paper and follow with applying 000 steel wool. The nickel stinger is also a benefactor of the steel wool polishing again.Moving on, the full regimen of 9 micromesh pads are applied by first wet sanding with pads 1500 to 2400 and dry sanding with pads 3200 to 4000 and 6000 to 12000.  Between each set of 3 pads, Obsidian Oil is applied to condition the vulcanite and to guard against oxidation. I love the glossy pop of newly micromeshed vulcanite! I had observed earlier that the Kaywoodie screw in stem was over clocked a few degrees.  This happens over time with tightening and loosening.To correct this problem and to bring the stem back to an accurate orientation, a Bic lighter is used to heat the nickel 4-hole stinger.  Since the stinger is gripped by the vulcanite of the stem, the goal is to warm the stinger so that the vulcanite gripping the stinger heats and loosens its grip allowing the stinger to rotate. After heating the stinger, I quickly re-screw the stem into the threaded shank facing and when it tightens to the orientation pictured above, I continue to apply clockwise pressure and the heated vulcanite releases its grip and it allows me to turn the stem one full revolution to line it up correctly.  I had to heat the stinger twice as the first try did not loosen the grip.  After lining the stem orientation correctly, I leave the stem in place and as the vulcanite cools, the grip on the stinger is re-engaged holding the stem again in the proper orientation.Time to address the dyed stummel.  It has been resting for several hours to help stabilize the dye in the briar.I use a cotton pad wetted with alcohol to wipe down the dyed stummel.  I do this to remove excesses of dye on the surface and to lighten and blend the new dye.Next, I mount a cotton cloth buffing wheel onto the Dremel and simply buff the stummel.  I do not use any compounds so that the compound dust does not fowl up the surface getting lodged in the plethora of hiding places on the Burl surface causing me to have to clean it!  The Dremel is a great tool for getting into the nooks and crannies of the Natural Burl landscape. I’m able to rotate and move up and down ridges and to reach into crevasses.  The newly dyed surface responds well to the buffing wheel.  The coloring of the wheel shows that new dye is leeching out of the surface.  The more I’m able to remove now, less likely to come off on hands later!Next, I use the 1500 grade micromesh pad and lightly sand over the Burl surface.  The aim is to ‘scalp’ the peaks of the mountain tops on the craggy surface to lighten them.  The lightening of the peaks creates more contrast and depth definition to the landscape.  I follow the scalp sanding by running the Dremel’s buffing wheel over the surface again.  This, I believe, achieves the ‘2-toned’ look of Kaywoodie’s design for the ‘Natural Burl’ line.In the homestretch – next, I mount another buffing wheel onto the Dremel setting the speed at about 40% full power.  After reuniting the Kaywoodie’s stem and stummel, Blue Diamond compound is applied to the rim and smooth briar surface on the underside and end of the shank.  The compound is also applied to the stem.  After applying the Blue Diamond compound, the pipe is buffed with a felt cloth to remove the compound dust from the areas on the stummel and from the stem.  Next, another cotton cloth buffing wheel is mounted and set at the same speed and carnauba wax is applied to the entire pipe.  I’m careful to apply with a very light touch of wax to the Natural Burl surface not to allow wax to build up in the crannies.  Wax is applied to both stummel and stem and then the pipe receives a rigorous hand buffing with a microfiber cloth to raise the shine.

Wow!  I’m very pleased with how this Kaywoodie Natural Burl Apple shaped up.  The brown craggy finish is flecked with shade differences that give it a depth and warmth – a rustic knobby feel.  I always enjoy the contrast nuances that the coalescing of rough and smooth briar creates. The smooth briar underside and shank ring alongside of the Burl texture is nice.  I’m amazed that this pipe occupied the lower shelf on Kaywoodie’s offerings back in the day when Sam chose it and added it to his rotation of pipes.  The TLC it has received has enhanced the briar presentation with this unique Natural Burl finish. I appreciate the collaborative help from Bill Feurbach who even as the president of the S.M. Frank Co., was not hindered from helping with the recommissioning of this one vintage Kaywoodie – a pipe man at heart.  Thanks, Bill!  I like the Natural Burl a lot and I trust that Joe likes it too.  Paw’s Kaywoodie Natural Burl 33 – Large Apple, that was put into production in the mid-50s/early 60s, is a venerable 60-year-old(!), and is starting a new lifetime in the loving care and stewardship of Paw’s family.  Adding frosting to the Kaywoodie cake, Joe’s commissioning of this restoration of Paw’s Natural Burl also benefits the Daughters of Bulgaria – women and girls who have been trafficked and sexually exploited.  Thanks for joining me!

Far from my normal style – a McIkl Wedgebull

6 Replies

Blog by Steve Laug

Jeff picked up this odd or unique or (ugly?) geometric bulldog in a group of pipes that we purchased recently. It came in the pipe bag pictured below and to the left. It is soft suede leather that is a mix of greys. It has the logo of the brand and the name of the pipe maker on the fount of it. It is a very different looking pipe with lots of edges to the shank and bowl and very geometric look to it. The finish is a very shallow sandblast and the stain on the briar is a mixture of tans, browns, blacks and even a bit of green. It has a black ebonite stem that has a very different style of saddle. The tenon is well made and the end is funneled to draw the smoke into the mouth of the pipe man or woman. The pipe is stamped on the left panel of the shank and read McIKL near the shank end.

The pipe was dirty with grime and dust in the finish of the sides and rim top. There is a medium cake in the bowl but no lava overflow onto the beveled rim top. The inner edge and the outer edge both looked to be in excellent condition. The ebonite stem had light tooth marks and chatter on the surface of the stem on both sides ahead of the button. Otherwise it is a clean looking stem. Jeff took photos of the pipe before he started his cleanup work. Jeff took photos of the rim top from various angles to show the condition of the bowl and rim as I described above. The finish is in good condition under the grime. The inner and outer edges of the rim look very good under the thick cake and light lava overflow. There do not appear to be any nicks of dents in the top of the rim. He took photos of the sides of the bowl showing the finish on the briar. It is sandblasted but has a very unique texture to it. You can also see the grime in the surface of the finish.Jeff took a photo of the stamping on the lower left side of the shank. It is very readable. It reads McIKL.  It appears that each letter is stamped individually judging from the spacing and alignment of the stamp.He took photos of the stem to show the oxidation and the tooth marks and chatter on both sides.The McIKL brand was not one that I had heard of before. I have worked on a lot of pipes but I have never seen a pipe like this one and I am unfamiliar with the brand. I turned to Pipephil’s site to see if I could find out information on the brand. There was nothing on the site on that brand. I turned to Pipedia and again found no information on the site.

I then did what I should have in the first place I suppose. I did a Google search of the brand and I found the pipe maker’s website (https://mcikl5.wixsite.com/pipes). There I found the very pipe that I am working on. It was on one of the pull down tabs called on artisan pipes. The carver called the pipe “Wedgebull”. The name is a perfect description of the pipe I am working on. It really is a series of wedges and triangles. I decided to include the information from the site on the briar and stem as well as the details size, weight and original cost of the pipe. I actually had no idea what a pipe like this would have cost originally so I figured that might be helpful information to include.

Wedgebull

Stummel: briar – David Bruken (Spain)

Stem: ebonite – SEM (Germany)

Total Length : 120 mm / 4.72 in

Bowl Height : 52 mm / 2.04 in

Bowl Width : 58 mm / 2.28 in

Bowl Chamber Depth : 23 mm / 0.9 in

Bowl Chamber Width : 20 mm / 0.79 in

Weight : 57 g / 2.01 oz

Price: USD 310

He also included a great series of photos if you want to see that pipe along with other pipes he has made and is making. I am including some photos of the pipe to show what it originally looked like. With a clearer picture of the pipe maker in mind I turned to work on this pipe. Jeff had done a great job in cleaning up this pipe. He had reamed the bowl with a PipNet reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife. He took back the cake to the walls of the bowl. He also cleaned off the lava and grime on inner edge of the rim. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime on the bowl and rim and rinsed it off with warm running water. He cleaned out the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol until they came out clean. He cleaned the stem with Soft Scrub to remove the grime on the exterior and cleaned out the airway with alcohol, cotton swabs and pipe cleaners. He soaked it in Before & After deoxidizer and rinsed it clean afterwards. The stem was a very tight fit and actually with the angles was hard to put in place on the shank. I took some photos of the pipe as I saw it. It was a very different pipe from all the others I usually work on. To show how clean the rim top and stem really was I took a close-up photo of the rim and stem. The bowl was clean and cake free. The rim top looked really good and the beveled inner edge of the bowl has all of the lava removed. The ebonite stem looks very good. The surface and the button edge appear to be in good condition. There were some small tooth marks and chatter on both sides but it looked good.I took the stem off the pipe and took a photo to show the shape of the Wedgebull – it is a pipe of many angles and triangles. It is very unique and the ebonite stem is uniquely shaped to work well with the shape.My part of this restoration was quite simple as the bowl was in great condition after Jeff’s cleanup work. I moved straight to working some Before & After Restoration Balm into the finish of the bowl and the rim top. I worked it into the surface with my fingertips and a horsehair shoe brush to clean, enliven and protect the wood. I let the balm sit for 10 minutes and buffed it off with a soft cotton cloth. I repeated the process a second time and the pipe began to show its colours. Next on my list was to work on the fit of the tenon in the shank. Jeff had mentioned that it was very tight from the time he received it. I used a piece of 220 grit sandpaper to carefully and slowly reduce the diameter of the tenon to give it a snug but not tight fit. It did not take too much work and the fit was perfect.With the fit of the stem in the shank cleaned up I could stem the bowl aside and turn my attention to the stem. I also sanded out the light tooth marks and chatter on the surface of the ebonite stem with a folded piece of 220 grit sandpaper. I followed the 220 grit sandpaper by sanding it with 400 grit wet dry sandpaper to begin the polishing of the surface of the stem.    I polished the stem with Denicare Mouthpiece Polish to take out the sanding marks around the button area. I buffed the stem with a microfiber cloth.I polished out the scratches with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the stem down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. Once I had finished the polishing I wiped it down with Briarville’s No Oxy Oil and set it aside to dry. I have to tell you the angles on this pipe make the work of restoring hard on the hands! So I am very happy to be on the homestretch with this pipe and I really look forward to the final look when it is put back together and polished and waxed. I put the bowl and stem back together. I polished the bowl and stem with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The Wedgebull bowl really looked good with the polished ebonite saddle stem. The combination colours in the stain coat on the bowl really work well with the black of the polished ebonite stem. For all the pain the angles caused me in working on it I have to tell you that it is a very comfortable pipe to hold in the hand. The finished pipe is shown in the photos below. The dimensions of the pipe are Length: 4.72 inches, Height: 2.04 inches, Outside diameter of the bowl: 2.28 inches, Chamber diameter: .75 of an inch. This pipe will be going on the rebornpipes store shortly if you are interested in adding it. Let me know if you want me to put it aside for you. Thanks for reading this blog and my reflections on the pipe while I worked on it. This is an interesting estate to bring back to life.

Another Legacy Pipe of a Great-Grandfather: Challenges Working with ‘Brylon’ on a Medico Apollo

1 Reply

Blog by Dal Stanton

It gave me a great sense of satisfaction when I received Joe’s response to reading and seeing the results of restoring the first of Paw’s pipes entrusted to me.   Joe and his wife, Hannah, who live in Athens, Greece, and are colleagues working in our organization, last year sent me a Kaywoodie “500” that I restored (See Link: Reclaiming Paw’s Kaywoodie “500” 04 Long Stem Billiard – A Great-Grandfather’s Legacy) as a gift for Hannah’s father, Ben, ‘Paw’s’ grandson.  The Kaywoodie was a special gift for Ben’s birthday.  Later, Joe wrote this letter:

Hello Dal,

My in-laws came to Athens to visit Hannah and I last month. I gave Ben the pipe. I showed him everything you wrote and documented about it. He absolutely LOVED how the pipe looked, and he was also deeply touched by the love, care, and respect you showed not just the pipe but his family. 

So many things you said in your blog triggered sentimental images for Ben about his grandfather, Sam Ellison. You called Sam (AKA Paw) a “knocker” and explained that based on some of the inner rim damage, that was from when Sam would knock out residual tobacco from the bowl, and Ben immediately could remember and visualize Sam doing that. 

During Ben’s last few days in Athens, he lived in blissful nostalgia, thinking of Paw and sweet memories along with him. When Ben went back to Georgia, he went through the storage unit and found stacks of old pictures and articles. Unfortunately, he couldn’t find a picture of him smoking the pipe, but there are some pictures (that I will attach below) of Paw with some of his tobacco co-workers at Brown & Williamson Tobacco Corp, along with an article in the Brown & Williamson newsletter, “The Pipeline” about him called ‘Two page Sam’. 

Two pictures Joe included were of Ben, his father-in-law fellowshipping with Paw’s newly restored Kaywoodie “500” and reminiscing about his grandfather.  What I understood from Joe, was that Paw essentially was the one who raised Ben.  The other picture was Paw and Ben 45 years earlier….  This is why I love what I call my work, The Pipe Steward – pipes are passed on, but also the special memories those pipes uniquely bring with them are also passed on to the following generations.

What was also of great interest to me in Joe’s letter, not only was Paw a pipe man, but he was also a tobacco man –  not just a tobacco man, but a tobacco SALES man for the Brown & Williamson Tobacco, Corp. and sent clips of an article of this tobacco company’s magazine about Paw, or as the rest of the world new him, ‘Two-Page Sam’!  When doing a restoration (and I will get to that!) it doesn’t get better than this regarding the story a pipe tells.  Doing a little research, I find out that B&W would be considered a ‘Big Tobacco’ company and Wikipedia described the beginnings in the latter 1800s:

B&W was founded in Winston (today’s Winston-Salem), North Carolina, as a partnership of George T. Brown and his brother-in-law Robert Lynn Williamson, whose father was already operating two chewing tobacco manufacturing facilities.[3] Initially, the new partnership took over one of the elder Williamson’s factories.[4] In February 1894, the new company, calling itself Brown & Williamson, hired 30 workers and began manufacturing in a leased facility.

In 1927, the Brown and Williamson families sold the business to London-based British American Tobacco. The business was reorganized as the Brown & Williamson Tobacco Corporation. Manufacturing and distribution were expanded, and work on a new B&W factory in Louisville was begun.

The Wiki article jumps a century from this earlier history to the 1990s which was a time rife with controversy regarding infamous ‘Big Tobacco’, congressional hearings, cover-ups and 60-Minutes TV pop-journalistic investigations – all low-hanging ripe story lines for a John Grisham novel and movie contracts!  As tantalizing as this later storyline was, I was drawn more to the story of ‘Two-Page Sam’, the article written about Paw’s life and relationships through the years that the Wiki article jumped over.  I include this story from the December 1984 article that Joe sent from B&W’s company magazine, ‘PIPELINE’.  The piece was subbed: “’Two-Page Sam’ – An 81-year old retiree, with a memory like a steel trap, about his 43-year career with B&W”. I enjoyed the read immensely as it not only tells of the life of Paw – aka, Two-Page Sam, but its portrayal of period perspectives revealing much about life and relationships when Sam started work for B&W in 1923 and later.  Enjoy! After the test run with Paw’s first pipe, Joe entrusted me with three more pipes to restore – two more Kaywoodies and a Medico.  Paw’s choice of pipes tells much about him!  One of the Kaywoodies is another of the “500” series, but this time, in addition to the long-shank Billiard from last time, a “500” Rhodesian is added.  Paw liked the “500”s – they are smaller pipes easier for hands-free fellowship (and chewed bits!) and work, as Sam went from vendor to vendor in his job selling tobaccos.  The other Kaywoodie is a Kaywoodie Natural Burl 33 – the finish is great!  Here is the lineup of Sam’s pipes that Joe sent:Along with the other Kaywoodie “500” its obvious that Sam stayed with American made pipes – pipes that would be considered ‘working men’s pipes’.  They are not high shelf purchases but would be found on many of the shelves of the tobacconists and ‘mom & pop’ stores he served through the years.  Affordable pipes that would be the kind a person who had known life through the Great Depression and Great Wars – as a child then as an adult – often called, the Great Generation.  With a deepening understanding of the man who was a steward of these pipes, I’m appreciative of the trust that Joe (and Hannah!) has placed in me to restore them as treasured family heirlooms.  What’s even better is that these restorations benefit the Daughters of Bulgaria – women and girls who have been trafficked and sexually exploited.

After looking over the pipes, I decided to start with the Medico Apollo Brylon – the most challenging.  With the Medico now on the worktable I take some pictures to get a closer look. The nomenclature found on left shank flank reads MEDICO [over] Apollo [over] Brylon (with circled ‘R’ for registered trademark).  The stem has a fancy, lopsided (or worn away) ‘A’ for Apollo pressed into the right side.During my communications with Joe about the conditions of the pipes he intended to send to me, I was assuming that this Medico was a briar that had dulled.  It wasn’t until I received the pipe and started to research the Apollo ‘Brylon’ line of Medico that I discovered the stummel was not made of briar but ‘Brylon’.  Pipephil.eu confirmed another Medico Apollo Brylon and the stem stamping but with no further information about the ‘line’ Brylon.Pipedia’s short introduction to the article about Medico provides this:

Medico was created in 1933, and is still produced by S.M. Frank. The brand is famous for its pipe filters, which were launched in the same year. Since 1966, some models have been made in Brylon, a synthetic material, and others in briar. The brand was also sold by the English company Cadogan and Oppenheimer Pipe.

I discovered very quickly that Brylon was not a line and that the Medico Apollo on the worktable was not briar!  In 1966, an innovation was introduced by S.M. Frank of fashioning bowls from a synthetic material.  At this point I’m thinking about Paw’s Apollo, whether I could repair it with the same procedures as with briars?  Rim?  Cracked shank? Blending repairs?  The same Pipedia article continued later with this additional interesting information about Brylon:

The company ended up buying some of their main competition in 1955. That year the Kaywoodie brands came under the S.M. Frank Company. The Medico brand continued production through this transition without many changes. The next big change for the brand came in the late 1960s. In 1966, the company developed a synthetic material that combined the traditional briar wood with resins. It is known as Brylon. At that time, all Medico pipes were made from imported briar wood. In order to keep production costs down, the company began offering some lines with Brylon. Today, that is still true…. In the Brylon, the line includes the Lancer, Apollo, Standard, Varsity, Conqueror, Medalist, Cavalier, and V.F.Q. As far as price, the briar wood pipes tend to be higher in cost than the Brylon ones. Courtesy TobaccoPipes.com

In another Pipedia discussion of various material and construction methods used in pipe production lines generally, Brylon is identified as a “High Temperature Resin with Wood Flour”:

In 1966, S.M. Frank developed a material called “Brylon” made of a high temperature resin combined with “wood flour”, which is pulverized wood of varying consistency. The pipes were cheaper and more durable, but heavier in the mouth and had a tendency to smoke hot and wet. They are still made today and favored by some for their inability to be burnt out or otherwise damaged without significant effort and the ease of cleaning the pipe. For more information see S.M. Frank.

Well, the unique characteristics of Brylon are becoming more evident.  They are less expensive, have differing smoking behaviors compared to their briar brethren and purportedly to be less susceptible to burning and damage compared to their briar brethren, BUT, (I love the qualifier!) “without significant effort”.  I guess Paw’s proclivities were with significant efforts by the looks of his Apollo!  Wow!  I wonder if Sam took the durability billing of S.M. Frank as a challenge 😊?

The question now is whether the issues of this Medico Apollo are addressed differently than my normal briar restoration protocols?  The significant issues start with the rim damage.  With the restoration of the first of Paw’s Kaywoodies, he seems to have been a habitual bowl ‘knocker’ with consistent damage to the aft quadrant of the rim.  Using the stem as a handle, Paw seems to have inverted the pipe and thumped the bowl on something hard enough to dislodge the ash and dottle – probably on his way hurriedly to the car after visiting a client, having secured his sale of B&W product line working toward ‘2-Page’ success, and speedily transitioning his mind and body to the next visit! I take a few pictures to show the aft rim damage.The shank also has a huge crack starting on the top of the shank running to the bowl crook.  When I communicated with Joe before receiving the pipe, he commented about the stem’s metal filter housing being out of round.  When I received the pipe, the stem and stummel were joined.  When I gingerly extracted the stem from the mortise, I could see how the nickel had been bent.  When I tried to rejoin the stem and stummel, the fit was so tight that I decided to leave things like they were.  I began to question whether the stem was the original for this stummel and forcing it had caused the cracked shank?  Yet, the stem does have the Apollo ‘A’ stamping – probably, just bent so much that the mortise no longer can accommodate it.The stem’s condition I believe is confirmation that ‘2-Page Sam’ often had the Apollo in a hands-free mode with it clenched between his teeth while he filled out his orders!  The chewing of the bit is evident with severe chatter and bite compression.  The oxidation appears to be minor.There also is a pit and dent mid-way on the stem’s underside which will need addressing.To begin the restoration of Paw’s Medico Apollo, I work on cleaning the internal airway with pipe cleaners wetted with isopropyl 95%.  While cleaning, I discover that the pipe cleaners are obstructed at the bit-end of the stem.  I also use a shank brush to push through.  The shank brush does push through but what becomes evident is that the chewing of the bit appears have closed the airway to such a point, the pipe cleaners are hindered from functioning.  This is a problem for keeping the airway fully cleaned.  I’ll need to address this issue as well.  When the airway is as clean as I’m able to get it, the stem is added to a soak of Before & After Deoxidizer along with other pipes in The Pipe Steward queue, along with Paw’s other 2 Kaywoodies.After a few hours, the Apollo stem is removed from the Deoxidizer and I squeegee the liquid off with my fingers then wipe the stem with cotton pads wetted with alcohol to remove the resulting raised oxidation.Following this, paraffin oil is applied to the stem to condition the vulcanite and I put the stem aside for the oil to be absorbed.Turning my attention now to the Brylon stummel, the questions I asked earlier about how to proceed with the repairs have been clarified in my mind.  It was helpful to find a blog on Dad’sPipes, What the Heck is Brylon?? – A Yello Bole Standard Panel Billiard, where Charles Lemon had previously had the same questions regarding working on Brylon!  Charles’ blog mainly was focused on cleaning and polishing issues and not with actual repairs to the Brylon – the rim and shank in this case.  My note to Charles describes my proposed working approach with Brylon:

Charles, hope you and your family are well and staying clear of harm’s way during these difficult times. I read one of your blogs where you worked on Brylon. I’m working on a Medico Apollo Brylon that needs extensive rim work. I’ve attached a picture to give you an idea of the dark brown color. Of course, I’m thinking of briar dust and CA glue to do the patchwork. However, it will probably be lighter than the hue of this brown. Do you think adding a wee bit of dark brown aniline dye would work?  Do you have any best practices, beyond the blog I read 😊.  The default if patching doesn’t work is to top the stummel but that reduces the height.

Charles’ email reply came quickly: Hi Dal. Good to hear from you! I hope all is well with you and yours. I have not attempted to fill Brylon. To be honest I have avoided the stuff as there is limited resale value in it. I think you are right – briar dust will show paler against the brylon. Mixing in some dye may do the trick. If not, you can always top the bowl afterwards. Good luck with it. I’ll be interested to see the results!

Charles

Charles’ response was what I was hoping to hear regarding using a mixture of CA glue and briar dust, which is the main component of Brylon though briar is not specified as the wood component.  The issue is the coloring.  Fiebing’s Dark Brown Leather Dye, which is an aniline dye, I think might be a very close match, but I’ve never introduced dye to a CA glue before – what will it do?  The worst-case scenario is that the patch doesn’t work and I top the bowl, turning it into a Pot shape.  I’m thinking to first introduce just a small amount of the dark brown dye – a drop, to a puddle of CA glue and mix it thoroughly and see how the CA/dye mixture behaves.  Then, as with briar repairs, if the glue/dye mixture looks good, I’ll introduce briar dust and see what happens!  With this next day of quarantine in Bulgaria being beautiful, I work outside on my 10th floor Man Cave balcony.

The first two pictures are marking the start – looking at the inside of the rim and then the outside.After preparing my plastic mixing palette by covering it with some scotch tape to help in the cleaning later, I place a small mound of briar dust on the palette and next to it, a small puddle of BSI Extra Thick CA glue.Using an eye dropper, I place one drop of Fiebing’s Dark Brown Leather Dye in the middle of the CA puddle and it immediately expands through the puddle. Not able to take any additional intermediate pictures to chronicle the mixing – the clock starts ticking when the briar dust is introduced to the CA glue.  I used a toothpick to gradually pull briar dust into the CA/dye, mixing as I go. I noticed that the CA mixture thickened more rapidly than normal with the dye alone, but it didn’t solidify which was what I was concerned about.  When the mixing came to a point where the resulting putty was about the consistency of molasses, I troweled the putty to the rim to fully cover the damaged area. This picture shows the progress at this point and a bit of wind-blown briar dust on the Man Cave!I use an accelerator to hold the patch material to the rim – it did want to move a bit.  Examining the patch in the sunlight, I’m VERY pleased with the color.  It appears to be very, very close to the Brylon at this point in the process. With the same approach now as with briars, I start with the outer rim and file the patch mound down to near-flush with the Brylon surface. Before moving to the inside and top of the patch, I use 240 grade sanding paper on the external rim patch.  I’m anxious to see what it does.  As I sand, pockets do appear in the patch area in this rough state.Switching to the internal rim patch area, I mount a sanding drum to the Dremel and bring the patch down to flush.Carefully, I use the drum on the top as well. I do not want to be too aggressive by sanding below the plane of the rim with the more powerful mode of sanding. Following the sanding drum, continuing with 240 paper wrapped around a Sharpie Pen, the chamber is sanded to help blend the patch area and to clean the chamber.  Then 240 sanding paper is redeployed to fine tune the rim contours and to smooth the patch.  The color match is looking good but at this rough state, the patch area on the rim reveals the air pockets which I’ll work on masking in the later stages. Having reached this point in the repair on the rim, before doing more sanding to improve the rough patch area, I address the shank crack.  The question rolling around in my mind regarding Brylon is whether I should drill a counter-crack creep hole at the end of the crack?  The crack ends at the shank/bowl merger.  The two pictures show the crack and a closeup of the end of the crack.  Working on the Man Cave balcony, the best angle of sunlight to see the crack was in the flower box hanging over the edge of the balcony with signs of early spring sprouting in Bulgaria!Marking the end of the crack with an arrow, the crack has turned the vertical corner and is on the bowl side – just slightly.  Since this is the first time working on Brylon and I haven’t found others who have complied a list of ‘best practices’ working with Brylon, I decide to drill the hole to be on the safe side.  Earlier, I had decided not to reinsert the stem because it seemed that it was too tight and may have caused the crack.  I’m thinking that the best way to address the crack is first, to drill the counter-creep hole. Following this, carefully reinsert the tight stem and allow the nickel filter housing to expand the crack allowing thinner, regular CA glue to seep into the cavity assuring a stronger bond.  I’ll then remove the stem, closing the crack and hopefully removing the threat of the crack advancing.  I’ll be thinking about whether to use a band to protect the shank for future use.To prepare to drill, I use a sharp dental probe to create a guide hole for the drilling.  It took the use of a magnifying glass to identify the end of the crack.  Unfortunately, there was a bit of collateral damage, but nothing serious.  When I applied pressure to the dental probe to imprint the indentation for a guide, I discover the Brylon to be much harder than briar and with the additional pressure that was needed, the probe skidded off to scratch the stummel.  Ugh! – it will sand out later.Next, after mounting a 1mm drill bit onto the Dremel, I carefully drill a hole using the guide hole – a great help in keeping the hand-held drill bit from dancing around!  I’ve gotten better at drilling these holes freehand with the handheld Dremel extension – my main work tool.With the hole drilled, with fear and trembling I coax the filter housing into the mortise and as expected, the terribly tight fit helps expand the crack for a more effective application of CA glue.  I must be honest; I was bracing myself for the stummel to split, but thankfully it didn’t!  I will address the fit later after the shank is repaired and stabilized.With the crack expanded, a line of regular CA glue is run starting from the hole down the shank to the shank facing. After laying down the glue, the stem is extracted, and the crack again compresses with CA glue in the cavity.For some cosmetic help and to keep the glue in place, I sprinkled the glue line with briar dust. I put the stummel aside to allow the glue to cure.With the Brylon bowl on the sidelines, I turn my attention to the stem.  The first step will be to repair the chewed bit – Two-Page Sam’s trademark!  I take fresh starting pictures of the upper and lower bit to show the carnage.  After each of these, is the comparison picture after using the heating method to minimize the damage.  Using a Bic lighter the bit is painted with the flame heating the rubber and helping it to expand to regain some of its original disposition.  I think the heating definitely improved the minor chatter so that for the upper bit, sanding should be all that is needed with some filing to freshen the button. For the lower bit, again, chatter was minimized but patching will still be required for the compressions.Medium-Thick Black CA glue is used to do the fills.  After filling the deep compressions, I set the stem aside to allow the CA glue to cure.After the fills have cured, a flat needle file is used to file down the patch mounds and to shape and refresh the button.The upper bit also is the recipient of the filing to file out the more severe chatter and shape the button.After the filing, 240 grade paper is used to further smooth the upper and lower bit.  The repairs on the lower side are looking good. About mid-way on the lower side of the stem there is a dent and a divot.  I expand the 240 paper sanding to the entire stem to address these issues and to remove any oxidation hanging on.  I’m careful to guard the Apollo ‘A’ stamping from the sanding. Before going further with the fine sanding, I remembered that earlier that it was very difficult to clean the stem’s airway because the bit area was too compressed from Paw’s chewing the bit.  To address this, I start a new pipe cleaner down the airway while warming the bit with the hot air gun.  I warm it on the upper bit avoiding the fills that are on the lower bit.  I do this to avoid dislodging the fills which will not expand the same as the rubber.It works like a charm.  As the vulcanite warmed it becomes supple and I move the pipe cleaner gradually through the airway as the compressed area relaxes.  When the pipe cleaner is moving freely and normally, with the pipe cleaner remaining in the airway, I run the stem under cool tap water setting the expansion in the vulcanite airway.Next, the entire stem is wet sanded using 600 grade sanding paper followed by applying 000 grade steel wool as I normally do with briars. The nickel stem facing and filter housing also receive attention from the steel wool and clean up very nicely.Putting the stem aside, I focus on the shank repair.  The glue has cured, and I use 240 grade paper to clean away the excess patch material from the surface of the shank.  The half-rounded needle file helps to remove the thicker patch buildup at the crook of the shank and bowl.Charles Lemon’s blog on ‘Dad’s Pipes’ was helpful to know what to expect working on the sanding and polishing of Brylon – or, what NOT to expect.  He found that Brylon does not polish up like briar but remains somewhat speckled and a dulled finish.  With my repairs on the Brylon being more intrusive than Charles’ experience, my concern is for the overall blending of the surface.  Will the area of Brylon that has received more focused 240 sanding appear differently from the other areas in the end?  To avoid this, I decide to encourage overall blending beginning with wet sanding the entire bowl, including the patch, with 600 grade paper.  This is followed with applying 000 steel wool.  The following pictures show the result – a darkening of the Brylon finish and with the uniform blending that was my hope.  This result encourages me to continue the fine sanding on the Brylon surface but also to continue blending the patches.Before moving forward with sanding and polishing of either the stem or stummel, one more technical challenge has yet to be remedied: the fit of the stem into the mortise.  With the shank crack glued, the last thing I want to do is to crack it again!  The picture shows the irregular shaping of the nickel housing.  The starting place is to ‘re-round’ the housing.  I use needle-nose pliers to do this.  First, I heat the nickel with the hot air gun to encourage movement in the metal without splitting it.  After heated, with the closed needle-nose pliers inserted into the nickel housing, I slowly turn the stem and apply gentle pressure to coax the nickel into a more rounded orientation.  Patience is key! Not perfect, but much better.  I don’t want to put too much stress on the nickel, so I decide to stop.No surprise – I try a half-hearted attempt to engage the stem and stummel but fit remains too tight.  The next step is to relieve the internal mortise pressure. I find a drill bit small enough to accommodate being wrapped with 240 grade paper and able to navigate the mortise.  Once, I get the best fit, I sand the mortise and attempting to fit the stem as I go.  It becomes clear that the roundness, or lack therein, of the filter housing was continuing to cause problems with ‘high spots’ as I attempted to rejoin the stem.  After returning to the hot air gun and making further adjustments to the nickel housing, I achieved a round housing that fit BUT the adjustment now left the housing lose in the mortise…ugh.  The restoration nightmare – repairing a repair.The solution I decided on was to rebuild the internal mortise grip by painting the mortise with acrylic nail polish.  I paint the mortise walls with the small brush provided, wait for it to dry and then paint it again, adding an additional layer.  This was not part of the plan…After several revolutions of adding layers of acrylic polish, the grip in the mortise was restored.  A detour but moving forward!The full regimen of micromesh pads is applied to the stem starting by wet sanding with pads 1500 to 2400 followed by dry sanding with pads 3200 to 4000 and 6000 to 12000.  Between each set, Obsidian Oil is applied to condition the stem and protects it from developing oxidation.  The stem is looking good! I decide to run the Brylon stummel through the full micromesh battery as well.  I’m not sure it will enhance the shine much, but I want to continue the process of blending the entire stummel surface, including the rim patch.  Wet sanding begins with pads 1500 to 2400 and is followed by dry sanding with pads 3200 to 4000 and 6000 to 12000.  The results are good.  The surface did shine up and the color deepens. Before applying Blue Diamond compound, I want to apply some cosmetic touches.  The crack in the shank is visible as a lighter line.  The large rim patch is speckled as well.  Using a walnut colored dye stick, I apply it to the shank and to the rim with very nice results.  The dye helps the blending. Next, to continue with polishing, I apply Blue Diamond compound to the stem and stummel after mounting a cotton cloth buffing wheel to the Dremel with the speed set at about 40% full power.After completing the application of Blue Diamond, one more cosmetic project awaits attention before applying wax. The Apollo ‘A’ stamping needs refreshing.  I apply a small dab of white acrylic paint over the stamping.Then, with a cotton pad, I tamp the paint drawing off the excess paint leaving a thin layer of paint over the stamping which dries very quickly.Then, using a toothpick’s flat side, I lightly scrape over the stamping to remove the excess paint leaving behind the paint in the imprint.  The ‘A’ appears to be partially worn and the paint only hold where the imprint is deep enough.  It looks good!Finally, another cotton cloth buffing wheel is mounted onto the Dremel, set at the same speed, carnauba wax is applied to the entire pipe.  The Brylon doesn’t absorb like briar so the wax seems to only make a very superficial shining on the surface.  Because of this, very little wax was needed on the surface.After completing the wax application, the final step in the restoration of Paw’s Medico Apollo Brylon was to give it a rigorous hand buffing with a microfiber cloth to raise the shine.

This restoration was a challenge but worth it!  Working with Brylon has unique challenges but it was good to learn more about how it behaves in case I have another S.M. Frank innovation come across my worktable!  The rim patch worked well but speckling remains as a reminder of Paw’s knocking activities!  In the end, this pipe of Paw’s legacy is ready to go again bringing with it the memories of the man called, ‘Two-Page Sam’ to be remembered and treasured by his family.  Thanks for joining me!