Tag Archives: polishing a vulcanite stem

Restoring a Gift Pipe from a High School English Teacher

Blog by Steve Laug

A few weeks ago, I received an email from a customer, Ted about some pipe work for him. He had three pipes that he said needed different things and offered to send some photos. He also sent a second email with a description of what each pipe needed. I have included that email and the photos he sent below.

Peterson 309 needs stem restoration and bowl cleaned out. Rhodesian needs full restoration – my English teacher from high school gave it to me a little over two years ago. The Comoy’s Canadian needs a new bit I broke it… After finishing the restem and restoration of the Comoy’s I moved on to the second pipe. The Rhodesian shaped pipe is stamped on the right side of the shank and reads Andre [signature script]. There was no other information stamped on the pipe. There was a light/moderate cake in the bowl with lava on the rim top. The finish was in decent condition but there was a varnish coat that was spotty. There was dirt and debris ground into the finish and particularly in the rusticated patterns on the bowl sides and around the outer edge of the rim. The stem was oxidized and there had obviously been a Softee Bit on the end as it left a line and some calcification next to the button. There were light tooth marks and chatter on both sides of the stem. I took photos of the pipe before I started work on it. I took a close-up photo of the bowl and rim top to show the cake in the bowl. The rim top shows some lava on the smooth finish. The inner and outer edges of the bowl looked good. The stem photos show the oxidation and calcification as well as the mark from the Softee Bit that I spoke of above. Otherwise, the tooth marks and chatter are minimal.I took a photo of the stamping on the pipe. It is stamped or etched on the left side of the shank. It was clear and readable as noted above. I removed the stem from the shank and took a photo of the pipe parts to give a sense of proportion of the pipe. It is quite nice.I wanted to know more about Andre so I did a bit of digging on the internet. I turned first to Pipephil’s site (http://www.pipephil.eu/logos/en/logo-a6.html) and found the brand listed. The signature on the pipe is the same as the one I am working on. I have included a screen capture and a side bar note below that gives some helpful information on the pipe.Artisan: André Mermet was a French craftsman who immigrated to the USA. He (and after him his son) produced pipes for Barclay Rex or Wilke pipeshops.

It was great to know that there was a connection to both Barclay Rex and Wilke pipeshops. Now I wanted to see if Pipedia had any more information but there was nothing listed.

I then quickly did a google search of the brand and low and behold I found that I had worked on one of his pipes back in 2018. The pipe was a very different shape than the one I have in my hands now but the rustication pattern is similar.Now, armed with that helpful information about the carver André Mermet and knowing that he provided pipes to such US companies as Barclay Rex and Wilke I was ready to work on the pipe itself.

I started my work by ream the bowl with a PipNet pipe reamer using the third cutting head to take the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife. I sanded the walls with a piece of 180 grit sandpaper wrapped around a dowel to smooth them out. I cleaned up the rim top with a worn piece of 1500 grit micromesh and a piece of 6000 grit wet dry sandpaper. It looked much better once it was finished. I wiped the bowl down with acetone to remove the varnish coat on the wood. It looked much better. I scrubbed the exterior of the briar with a tooth brush and undiluted Murphy’s Oil Soap. I rinsed it off with warm water to remove the grime and soap. It looked much better and the dust and debris was gone. I dried it with a cotton towel. I scrubbed out the internals of the pipe with 99% isopropyl alcohol, pipe cleaners and cotton swabs. I cleaned out the airway in the stem as well. I worked on these areas repeatedly until the shank and the airway in all the parts was clean.I polished the smooth briar with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down with a damp cloth after each pad. The bowl began to take on a rich shine. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. With that done, the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I sanded out the oxidation, calcification, light tooth marks and chatter along with 220 grit sandpaper and started polishing the stem with 600 grit wet dry sandpaper.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished polishing the stem with Before & After Pipe Stem polish (both Fine and Extra Fine) then wiped the stem down with another coat of Obsidian Oil. I am excited to finish the restoration of this Andre Rhodesian. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with microfiber cloth to deepen the shine. It is fun to see what the polished bowl with the nickel band looks like with the new, polished black, vulcanite stem was beautiful. This Andre Rhodesian is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ½ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 1.66 ounces/47 grams. It is a beautiful pipe and after I finish Ted’s last pipe I will be sending the three pipes back to him to enjoy. Thanks for walking through the cleanup with me as I worked over this pipe.

As always, I encourage your questions and comments as you read the blog. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipe men and women who hold our pipes in trust until they pass on into the trust of those who follow us.

Another Filthy and Messy Stanwell Made in Denmark Pot on the table

Leave a reply

Blog by Steve Laug

The next pipe I chose to work on came is another one from the lot of 11 pipes I purchased from a lady in Regina, Saskatchewan. She had found them in a house she bought and wanted to know if I wanted them. We struck a deal, I paid for the pipes and shipping and the box arrived while I was traveling in Europe. In the box were 4 Stanwells, I Danmore Bowl, 1 Soren Freehand, 1 Calabash with a Briar Bowl, 1 Nording Freehand, 1 Italian Made Bertenetti, 1 Rhodesian with a banded cracked shank, and 1 Brigham. I have restored the Nording, the snapped Stanwell, the Brigham, the Gourd Calabash with the briar bowl and restemmed the Danmore bowl. There are blogs on each restoration available. The next pipe on the table is one of the dirtiest pipes in a box full of very dirty pipes. It is stamped on the underside of the shank and reads Stanwell [over] Made in Denmark. There is no visible model name or shape number stamped on the pipe. There was a thick cake in the bowl, debris in the bottom and on the bowl walls and some remnants of tobacco. The airway was plugged and there was no draught on the pipe. There was a heavy lava overflow on the rim top and down the sides of the bowl and shank. It was hard to know the condition of the inner edges of the bowl because of the cake. The outer edge actually looked quite good under the grime. The finish was dirty and dusty and there was lava on the sides and heel of the bowl. The vulcanite shank extension was filthy and oxidized. The stem was in rough shape in appearance but underneath the calcification and oxidation the tooth marks and chatter looked minimal. I took photos of the pipe before I started my cleanup work on it. I took a close-up photo of the bowl and rim top to show the cake in the bowl. The rim top shows some thin lava spots on the smooth finish. The inner and outer edges of the bowl looked good. I took photos of the top and underside of the stem surface and button to show its general condition. It looked very good under the spotty oxidation.The stamping on the underside of the shank is faint but readable as noted above. You can barely make out the Stanwell stamp on the smooth panel near the shank extension but it is present. I took the stem off the shank and took a photo to give a sense of the proportion of the pipe.I recognized shape as being a Sixten Ivarsson design but Icould not remember the shape number associated with it. I turned to Pipedia’s article on shapes that Bas Stevens originally worked on to check it out (https://pipedia.org/wiki/Stanwell_Shape_Numbers_and_Designers). I am including a shape chart below. It identifies the shape as an 11 (bottom left corner of the photo below).I also have included two screen captures regarding the shape 11. The pipe I am working on is 11b in the list below. It is a slightly bent large, wide pot with a concave rim and various possible stem configurations (typically saddle, but can also be military mount, tapered, faux spigot saddle etc.), by Sixten Ivarsson.Now I knew it was an Ivarsson Design shape 11 with a military style saddle stem. Now it was time to work on the pipe. I removed the stem and turned my attention to the bowl clean up. I reamed the bowl with a PipNet pipe reamer using the fourth (and largest) cutting head to take the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife. I sanded the walls with a piece of 180 grit sandpaper wrapped around a dowel to smooth them out. I scrubbed the exterior of the briar with a brass bristle wire brush, a tooth brush and undiluted Murphy’s Oil Soap. I rinsed it off with warm water to remove the grime and soap. It looked much better and the dust and debris was gone. I dried it with a cotton towel. I worked over the damage on the inner edge of the bowl and the rim top. I also smoothed out the damage on the outer edge with a folded piece of 220 grit sandpaper. It looked much better after I sanded the damaged areas smooth. I worked over the rim top and the heel of the bowl with a dry brass bristle brush to remove some of the darkening. It is looking better.I scrubbed out the internals of the pipe with 99% isopropyl alcohol, pipe cleaners and cotton swabs. I cleaned out the airway in the stem as well. I worked on these areas repeatedly until the shank and the airway in all the parts was clean. I polished the vulcanite shank extension with micromesh sanding pads – wet sanding it with 1500-12000 git sanding pads. I wiped it down with a cloth and some Obsidian Oil.I stained the bowl with a light brown aniline stain to blend the lighter and darker portions into each other. I applied it with a wool dauber and then flamed it with a Bic lighter to set it in the grain. I repeated the process until the coverage on the bowl was what I wanted. I wiped the bowl down with isopropyl alcohol on cotton pads to make it more transparent and show the other colour underneath. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. With that done, the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I wiped it down with some Soft Scrub to remove the oxidation and calcification. I sanded out the light tooth marks and chatter along with the remaining oxidation with 220 grit sandpaper and started polishing the stem with 600 grit wet dry sandpaper.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished polishing the stem with Before & After Pipe Stem polish (both Fine and Extra Fine) then wiped the stem down with another coat of Obsidian Oil.I am excited to finish this Ivarsson Design Stanwell Made in Denmark 11. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with microfiber cloth to deepen the shine. It is fun to see what the polished bowl looks like with the polished black, fancy turned vulcanite stem was beautiful. This Stanwell Large Pot 11 is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ½ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 1.69 ounces/48 grams. It is a beautiful pipe and one that I will be putting in the Danish Pipemaker Section on the rebornpipes store. Thanks for walking through the cleanup with me as I worked over this pipe.

Restemming and Restoring a Comoy’s Vanguard 296 Canadian

1 Reply

Blog by Steve Laug

Peterson 309 needs stem restoration and bowl cleaned out. Rhodesian needs full restoration – my English teacher from high school gave it to me a little over two years ago. The Comoy’s Canadian needs a new bit I broke it… The box of pipes arrived on Tuesday here in Vancouver. I decided to work on the Comoy’s restem and cleanup first. The pipe is stamped on the top of the shank and reads Comoy’s [over] Vanguard. On the underside of the shank it is stamped with a shape number 296 mid-shank. That is followed by the COM stamp MADE IN LONDON in a circle with IN in the centre. Underneath the circle it is stamped ENGLAND in a straight line. There was a light/moderate cake in the bowl with lava on the rim top. The shank had the broken tenon inside that would need to be pulled. The finish was in decent condition. There was dirt and debris ground into the finish and there was spotty varnish/shellac finish on the surface of the briar. I always check a shank for cracks when the pipe has been dropped and a tenon snapped. There were several spidering cracks along the top of the shank on the pipe. I took photos of the pipe before I started work on it. I took a close-up photo of the bowl and rim top to show the cake in the bowl. The rim top shows some lava on the smooth finish. The inner and outer edges of the bowl looked good. I took photos of the stamping on the pipe. It is stamped on the top of the shank and on the underside. It was clear and readable as noted above.I took a close-up photo of the top of the shank to show the crack. You can see it mid shank. From top end of the crack it spread to the left and the right from the end. It looked as if it had been dropped and the crack spread.I put the bowl in the freezer for ten minutes to try to loosen the broken tenon. The change in temperature and the different expansion rates for briar and stem material would loosen it. I took it out and used a screw to turn into the airway in the tenon. I wiggled it free of the shank with very little problem.I decided to deal with the cracks in the shank first. I repaired each one with a small spot of glue on a tooth pick then heated the band and pressed it in place on the shank. I took photos of the newly banded shank to show what it looked like. I reamed the bowl with a PipNet pipe reamer using the third cutting head to take the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife. I sanded the walls with a piece of 180 grit sandpaper wrapped around a dowel to smooth them out. I cleaned up the rim top with a worn piece of 1500 grit micromesh and a piece of 6000 grit wet dry sandpaper. It looked much better once it was finished. I scrubbed the exterior of the briar with a tooth brush and undiluted Murphy’s Oil Soap. I rinsed it off with warm water to remove the grime and soap. It looked much better and the dust and debris was gone. I dried it with a cotton towel. I wiped the bowl down with acetone to remove the spotty varnish coat on the wood. It looked much better. I scrubbed out the internals of the pipe with 99% isopropyl alcohol, pipe cleaners and cotton swabs. I cleaned out the airway in the stem as well. I worked on these areas repeatedly until the shank and the airway in all the parts was clean.I polished the smooth briar with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down with a damp cloth after each pad. The bowl began to take on a rich shine. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. With that done, the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I wiped it down with some Soft Scrub to remove the oxidation and calcification. I sanded out the light tooth marks and chatter along with the remaining oxidation with 220 grit sandpaper and started polishing the stem with 600 grit wet dry sandpaper.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil.I finished polishing the stem with Before & After Pipe Stem polish (both Fine and Extra Fine) then wiped the stem down with another coat of Obsidian Oil. I am excited to finish restemming and restoration of this Comoy’s Vanguard 296 Canadian. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with microfiber cloth to deepen the shine. It is fun to see what the polished bowl with the nickel band looks like with the new, polished black, vulcanite stem was beautiful. This Comoy’s Vanguard 296 Canadian is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 6 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.09 ounces/31 grams. It is a beautiful pipe and after I finish Ted’s other two pipes I will be sending it back to him to enjoy. Thanks for walking through the cleanup with me as I worked over this pipe.

Re-stemming and Restoring a Danmore De Luxe Made in Denmark Scoop

Leave a reply

Blog by Steve Laug

Danmore was founded by Hans Sørensen in the early 1970s, and produced pipes from that time until the early 1980s, at one point having up to 30 employees. The pipes were sold in the first Dan Pipe catalog. In the early 1980’s, however, production ceased in Denmark due to labor costs, and the company’s production was outsourced to Italy and Spain, and they began to also make pipecleaners and smokers articles.

Sørensen focused on the pipecleaner side of the concern, and eventually bought a share in the factory in the Far East making them. Today the company, owned by Hans’ sons Jesper and Lars Sørensen, no longer makes pipes, and instead makes only pipe cleaners under the name Danmore Hobby Aps, selling only to hobby and craftshops in Denmark and Scandinavia.

Hans Sørensen passed away in 2012. The Sørensen family continues to own the trademarks for the use of the Danmore name in relation to pipes, matches, and tobacco.

There was also a shape chart on the site that I have included. The shape was a 3041 which I have drawn a red box around.With that I turned to work on the pipe. I went through my can of stems and found one that would work well with the bowl. It is a uniquely carved saddle stem with a twist of a freehand. I sanded the tenon now slightly to allow it to fit the shank. I put it in the shank and took photos of the pipe. I like the looks of the one I chose over the original! I set the stem aside and turned to the bowl clean up. I reamed the bowl with a PipNet pipe reamer using the second and the third cutting head to take the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife. I sanded the walls with a piece of 220 grit sandpaper wrapped around a dowel to smooth them out. I scrubbed the exterior of the briar with a tooth brush and undiluted Murphy’s Oil Soap. It looked much better and the dust and debris was gone. I dried it with a cotton towel. I scrubbed out the internals of the pipe with 99% isopropyl alcohol, pipe cleaners and cotton swabs. I cleaned out the airway in the stem as well. I worked on these areas repeatedly until the shank and the airway in all the parts was clean.I worked over the damage on the inner edge of the bowl and the rim top. I also smoothed out the damage on the outer edge with a folded piece of 220 grit sandpaper. It looked much better after I sanded the damaged areas smooth.I polished the briar with 1500-12000 grit micromesh sanding pads. I wiped it down with a damp cloth after each pad. The briar took on a deep shine that highlighted the grain. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. With that done, the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I “painted” the surface of the stem with the flame of a lighter to lift the tooth marks. I sanded out what remained with 220 grit sandpaper and started polishing the stem with 600 grit wet dry sandpaper. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished polishing the stem with Before & After Pipe Stem polish (both Fine and Extra Fine) then wiped the stem down with another coat of Obsidian Oil.I am excited to finish this restemmed Danmore De Luxe 3041 Made in Denmark Scoop. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with microfiber cloth to deepen the shine. It is fun to see what the polished bowl looks like with the rusticated gourd and the polished black, fancy turned vulcanite stem was beautiful. This Danmore De Luxe 3041 Scoop is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 6 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 inch, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.66 ounces/48 grams. It is a beautiful pipe and one that I will be putting in the Danish Pipemaker Section on the rebornpipes store. Thanks for walking through the cleanup with me as I worked over this pipe.

Restoring a Gourd Calabash with a Briar Cup from the Regina Lot

3 Replies

Blog by Steve Laug

The next pipe I chose to work on came from a lot of 11 pipes I purchased from a lady in Regina, Saskatchewan. She had found them in a house she bought and wanted to know if I wanted them. We struck a deal, I paid for the pipes and shipping and the box arrived while I was travelling in Europe. In the box were 5 Stanwells, 1 Soren Freehand, 1 Calabash with a Briar Bowl, 1 Nording Freehand, 1 Italian Made Bertenetti, 1 Rhodesian with a banded cracked shank, and 1 Brigham. I have restored the Nording, the snapped Stanwell, the Brigham and there are blogs on each restoration.The next pipe on the table is the calabash from the lot above. There is no stamping on the pipe, shank or extension. The outer bowl was gourd calabash, the cup in the bowl is briar and seems to be glued in the calabash. There was a thick cake in the bowl, cobwebs in the bottom and on the bowl walls and some remnants of tobacco. The airway was plugged and there was no draught on the pipe. There was a lava overflow on the briar cup top. The edges of the bowl were in good condition. The finish on the briar cup was dirty and dusty and there was some lava on the outer edge of the bowl. The gourd was also very dirty with dust and debris in the rustication. There was a turned briar shank extension in the shank end that was held in place by a tenon. The fit in the gourd shank was off because of the grime in the airway. The stem was oxidized and calcified on the top and underside. The stem had some light tooth marks and chatter on both sides. I took photos of the pipe before I started my cleanup work on it. I took a close-up photo of the bowl and rim top to show the cake in the bowl. The rim top shows some thin lava spots on the smooth finish and in the plateau. The inner and outer edges of the bowl looked good. I took photos of the top and underside of the stem surface and button to show its general condition. It had some light tooth marks and chatter on both sides.I removed the stem from the shank to get a sense of what the pipe looked like in terms of proportion and curves. It was well designed and flowed well from bowl cap to tip of the stem.I took the shank extension off the shank end. It was a push tenon that held it in place and it did not fit well against the shank end of the gourd. The briar bowl cup was stuck firmly in the gourd. At this point I was not sure whether it was just gummy or if it had been glued in place in the gourd. I used a cotton swab and alcohol to place the liquid around the gap between the gourd and the briar. I repeated the process and let it sit over night. It did not loosen at all. I even tried some acetone and again the bowl did not move.Since the bowl did not seem to be removable I decided to proceed with the clean up. I reamed the bowl with a PipNet pipe reamer using the third cutting head to take the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife. I sanded the walls with a piece of 220 grit sandpaper wrapped around a dowel to smooth them out. I scrubbed out the internals with 99% isopropyl alcohol, pipe cleaners and cotton swabs. In this case it was more intensive than normal. I cleaned inside of the bowl and the airway at the bottom of the bowl. I cleaned out the inside of the gourd from the shank end and also the inside of the shank extension. I cleaned out the airway in the stem as well. I worked on these areas repeatedly until the shank and the airway in all the parts was clean. I scrubbed the exterior of the briar cup and the gourd with a tooth brush and undiluted Murphy’s Oil Soap. It looked much better and the dust and debris was gone. The key with gourd is not to leave water sitting on it for long. I dried it repeatedly and blew air through the airway to dry out the inside of the gourd. I polished the briar top of the briar cup with 1500-12000 grit micromesh sanding pads. I wiped it down with a damp cloth after each pad. The rim top took on a deep shine that highlighted the grain. I worked some Before & After Restoration Balm into the surface of the briar and the gourd with my fingertips and a horsehair shoe brush to clean, enliven and protect the briar. I also worked it into the shank extension with my fingers. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. With that done, the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I wiped the bowl down with cotton pads and SoftScrub cleanser to remove the oxidation. Once finished I “painted” the surface of the stem with the flame of a lighter to lift the tooth marks. I sanded out what remained with 220 grit sandpaper and started polishing the stem with 600 grit wet dry sandpaper. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. I gave it a coat of Obsidian Oil to preserve and protect the stem.I am excited to finish this Gourd Calabash with a Briar Cup insert. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with microfiber cloth to deepen the shine. It is fun to see what the polished bowl looks like with the rusticated gourd and the polished black, fancy turned vulcanite stem was beautiful. This Gourd Calabash with a Briar Bowl is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 7 ½ inches, Height: 4 inches, Outside diameter of the bowl: 2 ½ inches, Chamber diameter: 7/8 of an inch. The weight of the pipe is 3.77 ounces/106 grams. It is a beautiful pipe and one that will be staying in my collection for the time being. Thanks for walking through the cleanup with me as I worked over this pipe.

Restoring a Nording Made in Denmark Freehand from the Regina Lot

2 Replies

Blog by Steve Laug

I did find a great collage of photos of Erik Nording that I have included below. I turned to the second information site – Pipephil’s (http://www.pipephil.eu/logos/en/logo-n2.html) did not find any more helpful information on the Nording Made in Denmark stamp.

I began my work by wiping the finish down with acetone to remove the varnish coat on the briar. It was spotty and uneven so wiping it down removed the remainder of the coat. I reamed the bowl with a PipNet pipe reamer using the third cutting head to take the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife. I sanded the walls with a piece of 220 grit sandpaper wrapped around a dowel to smooth them out.

I scrubbed out the internals with 99% isopropyl alcohol, pipe cleaners and cotton swabs until the shank and the airway into the bowl and the stem were clean.I scrubbed the exterior of the bowl and the rim a tooth brush and undiluted Murphy’s Oil Soap. It looked much better and the dust and debris was gone. I polished the bowl and the rim top with 1500-12000 grit micromesh sanding pads. I wiped it down with a damp cloth after each pad. The rim top took on a deep shine that highlighted the grain. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips and a horsehair shoe brush to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. With that done, the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. I gave it a coat of Obsidian Oil to preserve and protect the stem.I am excited to finish this Nording Made in Denmark Freehand. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with microfiber cloth to deepen the shine. It is fun to see what the polished bowl looks like with the mixed smooth, rusticated and plateau finish. Added to that the polished black, fancy turned vulcanite stem was beautiful. This mixed grain on the Nording Made in Denmark Freehand is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 6 ½ inches, Height: 2 ¾ inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.90 ounces/54 grams. It is a beautiful pipe and one that will be on the rebornpipes store in the Danish Pipe Makers section. If you are interested in adding it to your collection let me know. Thanks for walking through the cleanup with me as I worked over this pipe.

Restoring a Patent Pending Sepra-Bol Pipe

1 Reply

Blog by Steve Laug

The next pipe is a very unique one both in terms of design and shape. I have never seen anything like it. It is called a Sepra-Bol pipe. I thought this would be another chance to walk you through my process of working on each pipe that we purchase. Jeff has set up a spread sheet to track where the pipe came from, the date of purchase and what we paid for it so that we know what we have invested in the pipe before we even work on it. This takes a lot of the guess work out of the process. This particular pipe was purchased on 10/27/2022 from an Antique Shop in Seaside, Oregon, USA. I also want you to understand why we take the photos we do. If you have followed for a while then you will see the familiar pattern of the photos we include both in the before and midstream process of working on a pipe. It is not accidental as the photos have been taken to help me make an assessment of the pipe Jeff sees before he starts his clean up work. The photos of this pipe has some extra photos. We do this to record the condition that the pipe was in when received it and to assess what kind of work will need to be done on. When I look at these photos this is what I see.

The first thing I see is very unique looking pipe with a raised shank and a U-shaped double bowl – front one is larger than the back one. There is a Bakelite on the top of the second bowl and a Bakelite clean out cover on the lower part of the rear bowl. It has a vulcanite saddle stem. It is well proportioned and interesting old pipe.
The finish is dirty and there is grime and grit ground into sides of the bowl. There seems to be a coat of varnish on top over the briar. It barely hides the many fills in the bowl sides. There seems to be some interesting grain amidst the fills.
The rim top has some light lava and debris on the back rim top and the inner edge is coated with cake from the bowl. There is some darkening around the inner edge and top of the bowl. I think cleaning will reveal a real beauty.
The bowl has a thick cake and debris on the walls that hides the walls and some grime on the inner edge of the bowl but once it is clean we will know what the bowl and edges really look like. The outer edges look good and there does not appear to be any obvious burn damage to the top or bowl edges. The cap on the second bowl is dirty and inside it is dirty as well.
The vulcanite saddle stem is in good condition – dirty, oxidized and has tooth chatter and marks on both sides ahead of button. There is no logo on the stem sides.

Overall my impressions of this pipe is that it is a great looking pipe even with the putty fills around the bowl sides. I think that once cleaned up it will look pretty amazing. The shape looks like it will be comfortable to hold. The photos below confirm the assessment above.Jeff took close up photos so that I could have a clearer picture of the condition of the bowl, rim edges and top. The rim top photos confirm my assessment above. The cake in the bowl is thick with tobacco debris stuck on the walls. The rim top has light lava, grime and darkening around the top and edges in the rusticated surface. You can also see the condition of the outer edge and the inner edge is in great condition. The back bowl with the Bakelite cap shows dirt and grime as well. This is what I look for when assessing a pipe. There is no visible burn damage at this point. The bowl is still round and other than being in a used condition it is in great shape. The photos of the vulcanite stem surface from various angles confirmed my assessment of its condition. You can see that it is dirty in the first photo below. The stem has some tooth marks and chatter on the top and underside near the button. Instead of telling you what I see in the next photos of the sides of the bowl and the heel I want to hear from you. Tell me what you see? What does the finish look like to you? Are there any visible problems or issues that stand out to you? Are the cracks or scratches in the valleys of the rustication or the high spots? Are there visible fills, flaws or fissures in the briar? Any visible issues on the heel of the bowl? These questions should help you to see what I am looking for when I see these photos. Jeff took photos of the Bakelite bowl cap on the second bowl and the clean out cap in place in the bowl. He took them from the bowl and took photos of them to show what they look like when removed. It is an interesting set up. Jeff took photos of the fills around the bowl sides. They look swollen and enlarged. They are very visible in the photos below. They well need to be cleaned up, sanded and repaired to try to hide them in the surrounding briar. As the pipe stands at the moment the fills really are a mess.He took photos of the stamping on heel of the bowl. It reads Imported Briar [over] Sepra Bol. Underneath that it is stamped P.O Box 18202 [over] Houston 23, Texas USA. Stamped under that it reads Pat. Pending. On the underside of the shank at the shank/stem union it is stamped ITALY. What stands out for you in the photos of the stamping on the pipe? What do you look for in the stamping? I know it is dirty but what do you see underneath the grime on the surface of the briar? When I am working on pipes I like to get a sense of the history of the brand of the pipe and try to get a feel for the pipe maker. I turned to Pipephil’s site and to Pipedia to see what I could learn about Sep-ra Bol pipes. There was nothing listed for the brand there.

I googled the Sep-ra Bol pipe to see what I could find out about the brand. One of the links took me to imgur.com (https://i.imgur.com/0LjqtVQ.jpg). There was a great advertisement for the pipe included there. I have done a screen capture of the advert and included it below. Give it a read as it a fascinating description of the specialty pipe.
I love the description of the pipe as “a new, exclusive two bowl principle protects your health…adds to the rich tobacco flavor… and is easy to clean. No wasteful, gummy heel. No unpleasant odors…no metal. Doesn’t cause heart-burn or upset digestion. A fine briar pipe endorsed by smokers everywhere… The smoke is filtered through your favourite tobacco so it is always cool and dry.”

I have included a blown up photo of the diagram describing the function of the pipe. It is much as I expected.The Imgur site also had another advertisement on the pipe. I have included it below. It give a clear photo of the pipe with tobacco inserted in the second bowl to act as a filter and says that it is easily replaceable. It also connects the pipe to the maker – International Allied Industries – Hialeah, Florida. With that collection of information and advertisements digested it was now time for me to work on the pipe.

I am once again including the link to Jeff’s clean up process blog. Please remember that the point of these blogs is not to wow you with the work or make you shake your heads but I want you to know the details of the work we do so you can do your own. Back in 2020 Jeff wrote a blog about his cleaning process. I am including a link to that now so you can see what I mean about his process. Do not skip it! Give it a read (https://rebornpipes.com/2020/01/20/got-a-filthy-estate-pipe-that-you-need-to-clean/). Here is the introduction to that blog and it is very true even to this day.

Several have asked about Jeff’s cleaning regimen as I generally summarize it in the blogs that I post rather than give a detailed procedure. I have had the question asked enough that I asked Jeff to put together this blog so that you can get a clear picture of the process he uses. Like everything else in our hobby, people have different methods they swear by. Some may question the method and that is fine. But it works very well for us and has for many years. Some of his steps may surprise you but I know that when I get the pipes from him for my part of the restoration they are impeccably clean and sanitized. I have come to appreciate the thoroughness of the process he has developed because I really like working on clean pipe!

For the benefit of some of you who may be unfamiliar with some of the products he uses I have included photos of three of the items that Jeff mentions in his list. This will make it easier for recognition. These three are definitely North American Products so you will need to find suitable replacements or order these directly on Amazon. The makeup pads are fairly universal as we were able to pick some up in India when we were with Paresh and his family.

In the blog itself he breaks his process down into two parts – cleaning the stem and cleaning the bowl. Each one has a large number of steps that he methodically does every time. I know because I have watched him do the work and I have seen the pipes after his work on them. He followed this process step by step and when the pipe got to me it was spotlessly clean and ready for my work. The inside of the stem, shank and bowl were clean and to me that is an amazing gift as it means that my work on this end is with a clean pipe! I cannot tell you how much difference that makes for my work.

This very unique looking pipe with a raised shank and a U-shaped double bowl – front one is larger than the back one. There is a Bakelite on the top of the second bowl and a Bakelite clean out cover on the lower part of the rear bowl. It has a vulcanite saddle stem. It is well proportioned and interesting old pipe. It is clean and smells fresh.
The finish is clean and the grime and grit have been removed from the finish on the bowl. The smooth briar looks very good thought the fills on the sides of the bowl are numerous and quite ugly.
The darkening, lava, grime and dust on the rim top has been removed and it has revealed that the inner edge is clean and burn free. The outer edge of the bowl is also in good condition. The edges of the second bowl under the cap also look very good. The Bakelite caps on the second bowl and the clean out look very good.
With the cake reamed out the walls of the bowl are clean and they show no checking or burn damage to the walls.
The vulcanite saddle stem looks very good and cleaned up well. The light tooth marks an chatter will be easily polished out. There is no logo on the sides of the stem.

Hopefully the steps above show you both what I look for when I go over the pipe when I bring it to the work table and also what I see when I look at the pipe in my hands. They also clearly spell out a restoration plan in short form. My work is clear and addressing it will be the next steps. I took photos of the whole pipe to give you a picture of what I see when I have it on the table. This is important to me in that it also shows that there was no damage done during the clean up work or the transit of the pipe from Idaho to here in Vancouver. I carefully went over the bowl and rim top to get a sense of what is happening there. In this case once the rim top and edges were cleaned the rim top and inner edge showed no damage. The darkening on the rim top and edges was also gone. The varnish coat is spotty on the rim top and edges. The second bowl cap and clean out cap look very good. I go over the stem carefully. The fit to the shank is snug and the transitions are smooth. There were some light tooth marks and chatter on the surface of the stem and the button. I took photos of the rim top and stem sides to show as best as I can what I see when I look at them. I always check to make sure that the clean up work did not damage the stamping on the heel of the bowl and the underside of the shank in any way. It is in excellent condition and is very clear and readable.I love just looking at the lay of the pipe and the proportion of a pipe. I took the pipe apart to get a sense of what was in the mind of the pipe maker when he crafted the pipe. The photo shows its beauty in flow and shape. Even with the ugly fills in the bowl sides it is still a beauty. It was time to go to work on seeing what I could do with the fills in the bowl. They were so ugly that they cannot remain the way they are so I will need to do a bit of work to blend them into the surface of the surrounding briar. I started the process of reworking the shrunken fills. I stained the sunken fills with an Oak stain pen and then filled them in with clear CA glue. I spread the glue and flattened out the repairs areas using a dental spatula. I set it aside to cure. Once it had cured I sanded the repaired areas smooth with 220 grit sandpaper to blend them into the surrounding briar. I polished out the sanding on the bowl sides with 1500-2400 grit micromesh sanding pads and wiped it down after each pad with a damp cloth. I stained the briar with an Oak stain pen and it looked much better. I restained the bowl with a medium brown aniline stain. I applied it with a cotton dauber and then flamed it with a lighter to set the stain in the briar. I repeated the process until I was happy with the coverage.Once the stain cured I polished the briar with micromesh sanding pads – dry sanding lightly with 1500-12000 grit pads. I wiped the briar down after each sanding pad to trace the progress in the polishing. It definitely took on a shine with each successive pad. I rubbed down the bowl and shank with Before & After Restoration Balm. It is a paste/balm that is rubbed into the surface of the briar. The product works to deep clean the nooks and crannies of finish, enliven and protect the briar. I worked it into the briar with my finger tips. I let it sit for 10 minutes then wiped it off with a soft cloth then buffed it with a cotton cloth. The briar really began to have a deep shine in the briar and the rustication showed depth. The photos I took of the bowl at this point mark the progress in the restoration. It is a gorgeous pipe. I polished the bowl cap and clean out cap with micromesh sanding pads. I used 1500-12000 grit pads and wiped the caps down with Obsidian Oil. The caps took on a shine. I put the caps in place on the bowl and took some photos of the bowl at this point in the restoration process. It is a beauty and while the fills are still present they are less intrusive. I set the bowl aside and turned my attention to the stem. I “painted” the stem surface at the button with the flame of a Bic lighter to lift the tooth marks. I was able to lift them all quite well. I sanded out what remained with 220 grit sandpaper and the starting the polishing with 600 grit wet dry sandpaper. I polished the stem with micromesh sanding pads – 1500-12000 grit sanding pads and water to wet sand the stem. I wiped it down after each sanding pad with Obsidian Oil on a cotton rag after each sanding pads. I know that many say Obsidian Oil does nothing for acrylic stems, but I find it does two things – first it gives some protection to the stem from buildup and second it give the sanding pads bite in the polishing process. After finishing with the micromesh pads I rub the stem down with Before & After Fine and Extra Fine stem polish as it seems to really remove the fine scratches in the vulcanite. I rub the Fine Polish on the stem and wipe it off with a paper towel and then repeat the process with the Extra Fine polish. I finish the polishing of the stem down with a final coat of Obsidian Oil and set the stem aside to let the oil absorb. This process gives the stem a shine and also a bit of protection. The final steps in my process involve using the buffer. I buffed the stem with Blue Diamond to polish out the light scratches in the acrylic. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax. I have found that I can get a deeper shine if I follow up the wax buff with a buff with a clean buffing pad. It works to raise the shine and then I hand buff with a microfiber cloth to deepen the shine. It is always fun for me to see what the polished bowl looks like with the polished stem. It really is a nice pipe. The finish around the bowl sides and shank looks great with the rich brown stains. The stain hides the fills quite well. The Sepra Bol Imported Briar Two Bowl Billiard feels great in my hand. It is a well balanced pipe. Have a look at it with the photos below. The dimensions are Length: 5 ½ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.69 ounces/48 grams. It is such an interesting Sepra Bol Twin Bowl pipe that I will be keeping it here in my own collection. I look forward to enjoy a bowl in it soon. It should be a great smoking pipe.

Hopefully the style of this blog is helpful to you in some way. In it I wanted to show both what I am looking for and how I move forward in addressing what I see when work on a pipe. Let me know if it is helpful to you. It is probably the most straightforward detailed description of my work process that I have done. As always I encourage your questions and comments as you read the blog. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipe men and women who hold our pipes in trust until they pass on into the trust of those who follow us.

Restoring a unique Custombilt Convertibole Saddle Stem Billiard

1 Reply

Blog by Steve Laug

I thought it might be helpful to take you through my process of working on each pipe that we purchase. Jeff has set up a spread sheet to track where the pipe came from, the date of purchase and what we paid for it so that we know what we have invested in the pipe before we even work on it. This takes a lot of the guess work out of the process. This particular pipe was purchased on 05/01/2022 from an Antique Shop in Bozeman, Montana, USA. I also want you to understand why we take the photos we do. If you have followed for a while then you will see the familiar pattern of the photos we include both in the before and midstream process of working on a pipe. It is not accidental as the photos have been taken to help me make an assessment of the pipe Jeff sees before he starts his clean up work. We do this to record the condition that the pipe was in when received it and to assess what kind of work will need to be done on. When I look at these photos this is what I see.

The first thing I see is a classic Custombilt Rusticated Billiard with a twist and what appears to be an inserted bowl. It has a vulcanite saddle stem. It is well proportioned and well made with a great classic Custombilt appearance.
The finish is dirty and there is grime and grit ground into the rugged rustication on the sides of the bowl and shank. It is dusty and dull looking but under the grime the pipe looks good.
The rim top has some light lava and debris in the valleys of the rustication on the top and the edges. There is some darkening around the inner edge and top of the bowl. but cleaning will reveal a real beauty.
The bowl has a thick cake and debris on the walls that hides the walls and some grime on the inner edge of the bowl but once it is clean we will know what the bowl and edges really look like. The outer edges look good and there does not appear to be any obvious burn damage to the top or bowl edges.
The vulcanite saddle stem is in good condition – dirty, lightly oxidized and has tooth chatter and marks on both sides ahead of button. There is no logo on the stem sides.

Overall my impressions of this pipe is that it is a unique pipe even for Custombilt that once cleaned up will look pretty amazing. I like the tactile rustication style on Custombilts and have found nothing that comes close to it. The photos below confirm the assessment above. Jeff took close up photos so that I could have a clearer picture of the condition of the bowl, rim edges and top. The rim top photos confirm my assessment above. The cake in the bowl is thick with tobacco debris stuck on the walls. The rim top has light lava, grime and darkening around the top and edges in the rusticated surface. You can also see the condition of the outer edge and the inner edge is in great condition. This is what I look for when assessing a pipe. There is no visible burn damage at this point. The bowl is still round and other than being in a used condition it is in great shape. The photos of the vulcanite stem surface from various angles confirmed my assessment of its condition. You can see that it is dirty in the first photo below. The stem has some tooth marks and chatter on the top and underside near the button. Instead of telling you what I see in the next photos of the sides of the bowl and the heel I want to hear from you. Tell me what you see? What does the finish look like to you? Are there any visible problems or issues that stand out to you? Are the cracks or scratches in the valleys of the rustication or the high spots? Are there visible flaws or fissures in the briar? How random does the deep rustication look? Is there a pattern to it? Any visible issues on the heel of the bowl? These questions should help you to see what I am looking for when I see these photos. Jeff removed the bowl from the shank. It was threaded and screwed onto a threaded nipple set in the shank. You can see the deep grime in the finish under the bowl.He took photos of the stamping on a smooth panel on the right side of the shank. It reads Custombilt [over] Convertibole. What stands out for you in the photos of the stamping on the pipe? What do you look for in the stamping? I know it is dirty but what do you see underneath the grime on the surface of the briar and the acrylic? When I am working on pipes I like to get a sense of the history of the brand of the pipe and try to get a feel for the pipe maker. In this case I turned first to Pipephil’s site to see what I could learn about Custombilt (http://pipephil.eu/logos/en/logo-c8.html). I did a screen capture of the section on the screen. I have also included the information from the side bar below the photo.Chunky bowls with rough carving or gouges.

Tracy Mincer stopped making Custom-Bilt pipes in the early 1950s. The trademark was successively bought by Leonard Rodgers (1953), Consolidated Cigars (1968) and Wally Frank Co. (early 1970s). The later began to produce again his version of the pipe in 1974 or 1975 at Weber pipe factory (NJ). In 1987, the pipes were made out of the Butz-Choquin factory (France) and then Mexico until the late 1990s. Currently (2010), the Custombilt name is owned by Tobacalera of Spain which is part of Altadis.

It is generally admitted (but not proved) pipes stamped “Custom-Bilt” (with the hyphen) are from the Mincer era. The name might have changed from Custom-Bilt to Custombilt (without the hyphen) in 1946.

The pipe in hand that I am working seems to come after the change of stamping that happened in 1946.

I turned then to Pipedia (https://pipedia.org/wiki/Custom-Bilt). I found a brief history of the brand and read some interesting facts that I have included below. I am also include a screen capture and description of the stamp that is on the right side of the shank.I read further and found a description of the Convertibole pipe along with an advertisement for the pipe. I have included both below.

American companies such as Marxman were doing similar things. One Marxman carved head actually was valued at $7,500! It seems to me that Mincer was trying to show that the Custom-Bilt company was a complete outfit capable of making the same things as some of the “big boys” of the day.

There were other variations, such as the Convertible (removable bowl), the Saddle, Military Bit stems, and others. I really like the description “the newest idea in pipe smoking. Interchangeable for every occasion, as individual as a thumbprint, hand-crafted styles for office, home and outdoors.” You can also see the various bowls that were available and can be changed with “the twist of your wrist – plugs in a fresh pipe 2 or 3 times daily.

I have never seen a is a classic Custombilt Rusticated Billiard with a twist like this Convertibole. It has a vulcanite saddle stem. It is well proportioned and well made with a great classic Custombilt appearance.
The finish is clean and the grime and grit have been removed from the finish on the bowl. The rugged, tactile rustication pattern looks very good as well. There is a unique style removable bowl.
The darkening, lava, grime and dust on the rusticated rim top has been removed and it has revealed that the inner edge is clean and burn free. The outer edge of the bowl is also in good condition.
With the cake reamed out the walls of the bowl are clean and they look very good with no checking or burn damage to the walls.
The vulcanite saddle stem looks very good and cleaned up well. The light tooth marks an chatter will be easily polished out. There is no logo on the sides of the stem.

Restoring a No Name Natural Finished Oom Paul

Leave a reply

Blog by Steve Laug

The next pipe I have chosen to work on is a Natural Finish smooth Oom Paul with a bent saddle stem that I picked up in a lot of 10 pipes from a fellow on Vancouver Island who was selling his collection. This is the final pipe of the 10 so it has been a fun journey to clean them up. There is no stamping on the shank on either side. It is unmarked and a no name. The saddle stem has a no stamping either. The pipe is a nice looking pipe with some mixed grain around the bowl and shank. There are some small fills in the briar but not to ugly. It has a natural finish. It is light weight and comfortable pipe to hold. I brought it to the work table and turned it over in my hands. This is what I saw when I over the pipe.

The natural finish was okay with some hand oils on the sides of the bowl and grime ground into the finish around the bowl sides. The finish is rough and unfinished. It looks dull but the it really highlights the grain around the bowl sides and shank. There are some fills on the bowl – right side toward the top front, back of the rim top and one on the top of the full bent shank.
The smooth rim top was okay and the inner and outer edges looked good. There was no lava build on the top and the beveled inner edge. There was some grime on the rim top and a burn mark on the top front of the rim and the bevel.
There was a light cake in the bowl. It held the aroma of the tobaccos smoked in it – fortunately not aromatic. The walls looked to be undamaged but once I removed the light cake I could confirm that.
The vulcanite saddle stem is in good condition with just some oxidation and light tooth marks and chatter on the top and underside ahead of the button.
The heel of the bowl has a sanded spot that is flat and has not been sanded or smoothed out. It was made to be a sitter but it had not been finished out.

To summarize what I saw – this no name Oom Paul is a well made pipe. It is a dirty but otherwise in good condition. The stem is lightly tooth marked but otherwise undamaged. There does not appear to be any calcification, only some light oxidation on the stem surface. The look and feel of the pipe in the hand is great. It is going to clean up very well. Here are photos of the pipe before I started my clean up. The bowl of the pipe looked good. The rim top is clean but there is some darkening on the beveled inner edge of the bowl on the back right side. There was a burn mark on the rim top at the front of the bowl. There does not seem to be any damage to the smooth finish. I see no warning signs in the rim top or the edges of the bowl. I took photos of the stem to show the condition of it. Though hard to see there are light tooth chatter on the surface of both sides ahead of the button but it should clean up easily with polishing. The next photo captures the flattened heel of the bowl. It is still roughly finished and will need some sanding. I removed the stem from the shank and took a photo of it to give a sense of proportion. Now it was time to work on the pipe itself. I started my work on the pipe by cleaning the internals. The cake was quite thin but it can hold residual oils from previous tobaccos and I wanted to check the bowl walls for burn damage or checking. I reamed it with a Savinelli Fitsall Pipe knife and took the cake back to bare briar. I sanded the walls with 220 grit sandpaper wrapped around a piece of dowel. I worked on them until they were smooth. There was no checking or burn damage to the bowl walls. It was quite clean. I cleaned out the internals of the shank and the airway in the stem with 99% isopropyl alcohol, cotton swabs and pipe cleaners. I worked them over until they were clean. I scrubbed the bowl with acetone and a cotton pad to remove the oils on the sides of the bowl and spottiness from the bowl and shank. It looked much better once it dried off. I polished the briar with micromesh sanding pads. I choose to dry sand the briar rather than wet sand it. Again it is a matter of personal preference. I prefer to use the pads dry and find they work very well on the briar. I sand with each pad (9 in total) and group them by threes for ease of reference. I wipe the bowl down after each pad with a damp cloth to remove the sanding debris and check the briar. I love seeing the developing shine on the briar as I move through the pads which is why I include so many photos of this step. I worked some Before & After Restoration Balm into the finish on the bowl and shank. I worked it into the surface of the briar with my fingertips to clean, enliven and protect the wood. Once the bowl was covered with the balm I let it sit for about 15 minutes and buffed it off with a soft cotton cloth and the shoe brush. I polished it with a microfiber cloth. I took photos of the pipe at this point in the process to show what the bowl looked like at this point. It is really a beauty. I set the bowl aside and worked on the stem. I dry sanded both sides of the stem with 1500-12000 grit pads to polish it further. I wiped it down with a cloth impregnated with Obsidian Oil after each sanding pad. Though I know that it does not do much with the acrylic I find that it still adds depth to the final shine on the stem which grew deeper with each sanding pad. I finished polishing the stem with Before & After Pipe Polish – both Fine and Extra Fine polishes. I wiped the stem down with some Obsidian Oil afterwards and buffed it with a soft microfiber cloth. I took the No Name Oom Paul to the buffer to wax and polish. I buffed the bowl and stem with Blue Diamond polish on the wheel to polish out the scratches in the vulcanite. I gave the pipe multiple coats of carnauba wax on the wheel and then buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The Natural finish used on the briar brings out the grain and the bowl looks excellent with the shine and the bent saddle stem. The rich finish around the bowl and shank is quite remarkable and gives the pipe a great look. The No Name Oom Paul is a beautiful pipe and one that will be a great smoking pipe. The finished pipe is shown in the photos below with each of the stems. The dimensions of the pipe are Length: 5 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the large pipe is a light and comfortable 55 grams/1.94 ounces. This is a great looking Natural Finish Oom Paul. I will be adding it to the rebornpipes store in the American Pipe Makers Section. If you want to add it to your rack let me know. Thanks for walking through the restoration with me. Cheers.

Restoring a Stanwell Regd. No. 969-48 Hand Made Military Mount Billiard

1 Reply

Blog by Steve Laug

The next pipe I have chosen to work on is a nice looking smooth brown bent Billiard with a silver ferrule and a vulcanite military mount stem that I picked up in a lot of 10 pipes from a fellow on Vancouver Island who was selling his collection. The stamping on the left side of the shank reads Stanwell [over] Regd. No. 969-48 [over] Hand Made [over] In Denmark. On the right side it was stamped with the shape number 27. The silver ferrule is stamped Stanwell on the left side. The saddle military saddle stem has a stamped with a white Crown S Stanwell logo on the left side. The pipe is a nice looking pipe with some nice cross grain on the sides of the bowl and shank. It has a medium brown finish. It is light weight and comfortable pipe to hold. I removed the pipe from the Stanwell pipe sock and turned it over in my hands. It was in good condition.This is what I saw when I over the pipe.

The finish was very good with only some hand oils on the sides of the bowl and light dust and grime ground into the finish around the bowl sides. The brown stain is dull but the it really highlights the grain around the bowl sides and shank
The smooth rim top looked very good and the inner and outer edges look very good. There was no lava build on the top and the edges. There was some grime on the rim top but the rest looked clean and undamaged.
There was a light cake in the bowl. It held the aroma of the tobaccos smoked in it – fortunately not aromatic. The walls looked to be undamaged but once I removed the light cake I could confirm that.
The silver Stanwell ferrule on the shank end is undamaged and clean. There is some tarnish on the silver and it is dull but still looks good overall.
The thin, fancy saddle stem has a white Crown S logo stamped on the left side that identifies it as a Stanwell pipe. It is in excellent condition with just some light tooth marks and chatter on the top and underside ahead of the button.

To summarize what I saw – this Stanwell Hand Made Regd. No. military mount Billiard is a well made pipe. It is a dirty but otherwise in good condition. The stem is lightly tooth marked but otherwise undamaged. There does not appear to be any calcification or oxidation on the stem surface. The look and feel of the pipe in the hand is great. It is going to clean up very well. Here are photos of the pipe before I started my clean up. The bowl of the pipe looked very good. The rim top is clean but there is some darkening on the top back of the rim. There does not seem to be any damage to the smooth finish. The edges of the bowl were undamaged and looked very good. I see no warning signs in the rim top or the edges of the bowl. I took photos of the stem to show the condition. Though hard to see there is light tooth chatter on the surface of both sides ahead of the button but it should clean up easily with polishing. The next photos capture the stamping on the shank and the saddle stem. It read as I have noted above. I removed the stem from the shank and took a photo of it to give a sense of proportion. As is my practice when working on pipes I researched the provenance of the pipe. I turned first to Pipephil (http://pipephil.eu/logos/en/logo-stanwell.html) to see what I could find. I found a side bar note on the stamping on the pipe. I found there that the company had begun in 1942 and that the “Regd. No.” stamping was discontinued in late 1960s to very early 1970s. So now I knew that the pipe was made after 1942 and before the late 1960s or early 1970s. I wanted to see if I could pin down the date a bit more.

I then turned to Pipedia to learn more about the pipe (https://pipedia.org/wiki/Stanwell). I read through the article by Smoking Pipes.com there and would recommend it as being a good read. In the material there I found no additional information. I scrolled through the photos and the included catalogue pages and there I found something helpful. There was a late 1950s catalogue shown there that had the description of the pipe I have and also the shape 27 shown in the pages. I have included a screen capture of the page below. I have circled the shape in the photo below. With that information I had learned that this pipe was available in the late 1950s in the shape that I had in hand. The Regd. No. stamping on Stanwell pipes ended in the late 1960s or early 1970s. My guess would place this pipe in the period between 1958-1965. It is a real beauty.

Now it was time to work on the pipe itself. I started my work on the pipe by cleaning the internals. The cake was quite thin but it can hold residual oils from previous tobaccos and I wanted to check the bowl walls for burn damage or checking. I reamed it with a Savinelli Fitsall Pipe knife and took the cake back to bare briar. I sanded the walls with 220 grit sandpaper wrapped around a piece of dowel. I worked on them until they were smooth. There was no checking or burn damage to the bowl walls. It was quite clean. I cleaned out the internals of the shank and the airway in the stem with 99% isopropyl alcohol, cotton swabs and pipe cleaners. I also cleaned the adapter that had come with the pipe. I worked them over until they were clean. I scrubbed the bowl with undiluted Murphy’s Oil Soap to remove the oils in the sides of the bowl. I used a tooth brush to work it into the briar. I rinsed it off with warm running water to remove the soap and the grime. It looked much better once I dried it off. I polished the briar with micromesh sanding pads. I choose to dry sand the briar rather than wet sand it. Again it is a matter of personal preference. I prefer to use the pads dry and find they work very well on the briar. I sand with each pad (9 in total) and group them by threes for ease of reference. I wipe the bowl down after each pad with a damp cloth to remove the sanding debris and check the briar. I love seeing the developing shine on the briar as I move through the pads which is why I include so many photos of this step. I worked some Before & After Restoration Balm into the finish on the bowl and shank. I worked it into the surface of the briar with my fingertips to clean, enliven and protect the wood. Once the bowl was covered with the balm I let it sit for about 15 minutes and buffed it off with a soft cotton cloth and the shoe brush. I polished it with a microfiber cloth. I took photos of the pipe at this point in the process to show what the bowl looked like at this point. The light sandblast finish looks very good and has a real touch of beauty. I set the bowl aside and worked on the stem. I dry sanded both sides of the stem with 1500-12000 grit pads to polish it further. I wiped it down with a cloth impregnated with Obsidian Oil after each sanding pad. I find that it still adds depth to the final shine on the stem which grew deeper with each sanding pad. I finished polishing the stem with Before & After Pipe Polish – both Fine and Extra Fine polishes. I wiped the stem down with some Obsidian Oil afterwards and buffed it with a soft microfiber cloth. I took the Stanwell Hand Made Military Mount 27 Billiard to wax and polish. I buffed the bowl and stem with Blue Diamond polish on the wheel to polish out the scratches in the vulcanite. I gave the pipe multiple coats of carnauba wax on the wheel and then buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The stains used on the briar bring out the grain and the bowl looks excellent with the shine of the polished silver ferrule and the vulcanite Military mount saddle stem. The rich finish around the bowl and shank is quite remarkable and gives the pipe an incredible look. The Stanwell Hand Made 27 Billiard is a beautiful pipe and one that will be a great smoking pipe. The finished pipe is shown in the photos below with each of the stems. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the large pipe is a light and comfortable 34 grams/1.20 ounces. This is a great looking Hand Made Billiard. I will be adding it to the rebornpipes store in the Danish Pipe Makers Section. If you want to add it to your rack let me know. Thanks for walking through the restoration with me. Cheers.