Monthly Archives: August 2025

Breathing new life into another Beautiful “Malaga” Quarter Bent Egg

by Steve Laug

The “Malaga” Bent Egg is next pipe on the table. We purchased it off eBay on 08/22/24 from a seller in Harrison Township, Michigan, USA. The carver did a great job of shaping the pipe to follow the grain on the briar. The egg-shaped bowl, round shank and quarter Bent tapered stem look very good. The bowl had a thick cake that overflowed with thick lava onto the rim so that it was impossible to see if there was damage on the inner edges. The sides of the bowl and shank are very dirty with grime and oils from prolonged use. The grain around the bowl and shank appeared to be very nice mixed grain under the grime on the briar. The stamping on the left side of the shank read “MALAGA”. There was no other stamping on it. The stem had light tooth marks and chatter on the top and the underside of the stem ahead of the button. There was some oxidation deep in the vulcanite of the stem surface. Jeff took these photos before he started the cleanup work on the pipe.Jeff took close up photos of the bowl and rim to capture the condition of the pipe before he started his cleanup work. The rim top had thick lava overflow. The outer edge looked to be in decent condition. The stem is oxidized, calcified and has tooth marks and chatter on both sides. He also took a photo of the side and bottom of the bowl and shank to show the beautiful grain around the bowl. The photos show the general condition of the bowl and dirt and wear on the rich oil finish. It is very dirty but this is another beautiful pipe. Jeff took a photo to capture the stamping on the left side of the shank. The photo shows the stamping “MALAGA”. The stamping is very readable under the heavy grime.Before I started working on the pipe itself I went back and reread what I had found when I had worked on many of the Malaga pipes that had come across my work table. I am including a few pieces of information that I have gathered in the process.

For those of you reading this blog who are unfamiliar with the brand, I am including the link to a previous blog that I wrote. It gives some of the history of the Malaga brand and the Malaga Pipe Shop in Royal Oak, Michigan in the USA. Here is the link – https://rebornpipes.com/tag/malaga-pipes/.

I have also included a link to a catalogue and the history of the pipemaker George Khoubesser. If you are interested to learn more, then I invite you to follow the link to get a feel for the brand and the pipemaker.

George Khoubesser (picture to the left) started Malaga Briar Pipe Company and located it in Royal Oak, Michigan in the USA in 1939. It closed its doors for the last time in 1999 after 60 years in business. I have an old Malaga Catalogue that I scanned and put on the blog (https://rebornpipes.com/2013/02/09/george-khoubesser-and-malaga-pipes/). The catalogue describes the manufacture of the pipes as follows:

Painstaking caution is exercised in selecting flawless, perfect briar wood for the purpose of making and Curing of the “Malaga.” You can be certain of this fact, because none other than the choicest and finest select briarwood will withstand the “Malaga” Curing process. Other than the choicest quality and grain, will split wide open in the Curing vats… The Curing method renders all “Malaga” pipes, light in weight… Most all “Malaga” Senior pipes are left in their natural state; except for a skillful waxing which brings out the rich beauty of the virgin grain. No artificial polishing stain, shellac or varnishes are added. Malaga closed in 1999 after 60 years in business.

Jeff reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs, shank brushes and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils and tars on the rim and the grime on the finish of the bowl. He rinsed it under running water. He dried it off with a soft cloth. He was able to remove the lava build up on the rim top and the flat surface of the rim top and the inner edge had some burn damage on the front and back side. The outer edge was rough and nicked. I took photos of the pipe to show its condition before I started my work on it. The stem also looked better. I took close up photos of the bowl and rim top as well as the stem. You can see the condition of the rim top and bowl in the first photo. Jeff was able to remove all of the tar and oils but you can now see the damage on the top and the edges of the bowl. The top of the rim is rough and there is some burn damage and darkening on the inner edge on the front. The stem had light tooth marks and chatter on both sides near the button on both sides.I took a photo of the stamping on the shank to show the condition. The “MALAGA” stamp is clear and readable. I removed the stem from the shank and took a photo to give a sense of how the pipe looked. I decided to address the rim top and damaged inner edge of the bowl first. To remove the damage on the rim top and edges of the bowl sanded the top with 220 grit sandpaper. That removed a lot of the damage on the rim top and outer edge. I used a piece of 220 grit sandpaper to work on the inner edge of the rim and remove the darkening and clean up the damage.I sanded the bowl and rim with 320-3500 grit sanding pads to begin the process of removing the scratches and blending the restored rim top into the rest of the bowl. I wiped the bowl down after each pad with a damp cloth to remove the dust and debris. The photos tell the story. I polished the rim top and the briar with micromesh sanding pads. I dry sanded the bowl with 1500-12000 grit sanding pads. I wiped the bowl down after each pad with a damp cloth to remove the sanding dust. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The following photos show the bowl at this point in the restoration process. I am very happy with the results. Before turning to work on the stem I decided to bend the stem to match the angels of the bowl. I “painted” it with a lighter to soften the vulcanite enough to bend it. I pressed the rim top flat against the desk top and bent the stem to the same angle. I “painted” the stem surface with the flame and was able to lift the tooth marks significantly. I filled in the ones that remained with black extra strength CA glue. I set it aside to cure. Once it cured I flattened the repair with a small file and then sanded it smooth with 220 grit sandpaper. It began to look much better. I turned to the stem to address the issues on the surface of both sides at the button. I sanded the stem with 320-3500 grit sanding pads. I wiped the stem down with an Obsidian Oil cloth after each sanding pad. I think I finally beat the oxidation.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad Obsidian Oil. I finished by polishing it with Before & After Pipe Stem Polish both fine and extra Fine and then wiped it down with a final coat of Obsidian Oil. This is a beautiful “Malaga” Quarter Bent Egg with a vulcanite tapered stem. It has a great look and feel. The shape of the bowl, the rim top and the cut of the briar work well to highlight the grain around the bowl sides. I polished stem and the bowl with Blue Diamond polish on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The grain took on life with the buffing. The rich oil cured colour works well with the polished vulcanite stem. The finished Malaga Quarter Bent Egg has a rich look that is quite catching. Have a look at it with the photos below. The shape, finish and flow of the pipe and stem are very well done. The dimensions are Length: 5 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.41 ounces/40 grams. It is a beautiful pipe. I will be putting it on the rebornpipes store shortly in the American Pipemakers Section if you are interested in adding it to your collection. Thanks for walking with me through the restoration.

Breathing new life in to a Beautiful “Malaga” Algerian Briar Canadian

3 Replies

by Steve Laug

The “Malaga” Canadian is next pipe on the table. We purchased it off eBay on 08/22/24 from a seller in Harrison Township, Michigan, USA. The carver did a great job of shaping the pipe to follow the grain on the briar. The bowl, oval shank and straight tapered stem look very good. The bowl had a thick cake that overflowed with thick lava onto the rim so that it was impossible to see if there was damage on the inner edges. The sides of the bowl and shank are very dirty with grime and oils from prolonged use. The grain around the bowl and shank is very nice mixed grain. The stamping on the top of the shank read “MALAGA”. On the underside it is stamped ALGERIAN BRIAR. The stem had light tooth marks and chatter on the top and the underside of the stem ahead of the button. There was some thick calcification and also some oxidation deep in the vulcanite of the stem surface. Jeff took these photos before he started the cleanup work on the pipe.Jeff took close up photos of the bowl and rim to capture the condition of the pipe before he started his cleanup work. The rim top had thick lava overflow. The outer edge looked to be in decent condition. The stem is oxidized, calcified and has light tooth marks and chatter on both sides. He also took a photo of the side and bottom of the bowl and shank to show the beautiful grain around the bowl. The photos show the general condition of the bowl and dirt and wear on the rich oil finish. It is very dirty but this is another beautiful pipe. Jeff took a photo to capture the stamping on the top and underside of the shank. The photos show the stamping “MALAGA” on the top and ALGERIAN BRIAR on the underside. The stamping is very readable both sides of the shank.Before I started working on the pipe itself I went back and reread what I had found when I had worked on many of the Malaga pipes that had come across my work table. I am including a few pieces of information that I have gathered in the process.

Jeff reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs, shank brushes and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils and tars on the rim and the grime on the finish of the bowl. He rinsed it under running water. He dried it off with a soft cloth. He was able to remove the lava build up on the rim top and the flat surface of the rim top and the inner edge had some burn damage on the front and back side. The outer edge was rough and nicked. I took photos of the pipe to show its condition before I started my work on it. The stem also looked better.I took close up photos of the bowl and rim top as well as the stem. You can see the condition of the rim top and bowl in the first photo. Jeff was able to remove all of the tar and oils but you can now see the damage on the top and the edges of the bowl. The top of the rim is rough and the outer edges are chipped and rough. There is some burn damage and darkening on the inner edge on the left side. The stem had light tooth marks and chatter on both sides near the button on both sides.I took a photo of the stamping on the shank to show the condition. The “MALAGA” stamp is and the ALGERIAN BRIAR stamp are clear and readable. I removed the stem from the shank and took a photo to give a sense of what the pipe looked like.I decided to address the rim top and damaged inner edge of the bowl first. To remove the damage on the rim top and edges of the bowl sanded the top with 220 grit sandpaper. That removed a lot of the damage on the rim top and outer edge. I used a piece of 220 grit sandpaper to work on the inner edge of the rim and remove the darkening and clean up the damage.I sanded the bowl and rim with 320-3500 grit sanding pads to begin the process of removing the scratches and blending the restored rim top into the rest of the bowl. I wiped the bowl down after each pad with a damp cloth to remove the dust and debris. The photos tell the story. With the sanding I found a fill on the left side of the shank that is solid. There also appears to be one on the lower right side of the bowl that is also solid. I polished the rim top and the briar with micromesh sanding pads. I wet sanded the bowl with 1500-12000 grit sanding pads. I wiped the bowl down after each pad with a damp cloth to remove the sanding dust. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The following photos show the bowl at this point in the restoration process. I am very happy with the results. I turned to the stem to address the issues on the surface of both sides at the button. I sanded the stem with 320-3500 grit sanding pads. I wiped the stem down with an Obsidian Oil cloth after each sanding pad. I think I finally beat the oxidation.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad Obsidian Oil. I finished by polishing it with Before & After Pipe Stem Polish both fine and extra Fine and then wiped it down with a final coat of Obsidian Oil. This is a beautiful Malaga Algerian Briar Canadian with a vulcanite tapered stem. It has a great look and feel. The shape of the bowl, the rim top and the cut of the briar work well to highlight the grain around the bowl sides. I polished stem and the bowl with Blue Diamond polish on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The grain took on life with the buffing. The rich oil cured colour works well with the polished vulcanite stem. The finished Malaga Algerian Briar Canadian has a rich look that is quite catching. Have a look at it with the photos below. The shape, finish and flow of the pipe and stem are very well done. The dimensions are Length: 5 ½ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 1.23 ounces/35 grams. It is a beautiful pipe. I will be putting it on the rebornpipes store shortly in the American Pipemakers Section if you are interested in adding it to your collection. Send me a message or an email to slaug@uniserve.com Thanks for walking with me through the restoration.

Another Killer B – Peterson B2 4th of July

Leave a reply

By Al Jones

I enjoy finding unusual Peterson shapes. This B2, a stylized straight Rhodesian shape, was a 2001 “4th of July” commemorative that was recently listed on Ebay. It didn’t gather much attention and I won the auction. It joins a B5 Supreme in my pipe cabinet.

I wasn’t aware that Peterson made a short run of “4th of July” commemorative pipes. Whenever I have a Peterson question, I turn to Mark Irwins blog, Peterson Pipe Notes. From the blog, I learned that this line ran from 1998 to 2004. Mark had a blog entry dedicated to the B shape line:

47. Peterson B Shapes: A Visual Encyclopedia (B1 – B11)

The B2 shape is described as below:

The hallmarks are a bit worn, but the distinctive Q for the year 2001 is easily recognized.

The pipe was in good condition, but the uneven and scorched bowl top was doing to need some work. The stem had a tiny pin prick below the button and in very good condition. Below is the pipe as received.

I reamed the mild cake and soaked the briar with sea salt and alcohol. I decided that the scorched bowl top would need to be removed. I only had to remove a small amount of material to reach un-scorched briar. I used a Medium brown stain to finish the bowl top and match the pipe.

The P stem logo was in good condition but missing the while paint. I filled it with white acrylic nail polish and let it dry overnight. I buffed off the excess with a Micro-Mesh pad. The lightly oxidized stem was restored using 800, 1,500 and 2,000 grade wet sandpaper. The stem was then buffed with White Diamond and Meguiars Plastic polish.

The bowl was buffed lightly with White Diamond and then several coats of carnuba wax. I used some cream silver polish applied by hand on the silver band.

Below is the finished pipe and it has joined my B5 Supreme in my collection.

New Life for an interesting “Malaga” Wire Rusticated saddle stem Billiard

Leave a reply

by Steve Laug

This interesting Wire Rusticated Bent Billiard was purchased on 09/18/2024 on eBay where a seller from Cadiz, Kentucky, USA was selling it. It is a rich brown rusticated briar with a thin band around the shank end. The stem is an acrylic saddle stem. The rusticated finish was quite clean though there was dust in the grooves of the finish. The bowl was quite clean and recently reamed. The bottom of the bowl was raw briar showing that it had not been smoked to the bottom of the bowl. There faint aroma of tobacco in the bowl and shank. The rusticated rim top was quite clean and the inner edge looked very good. The pipe is stamped on the smooth band around the shank and reads “MALAGA”. The vulcanite, saddle stem had no stamping on the sides. It had scratches, tooth marks and chatter on both sides ahead of the button. It was really an interesting rustication and stain that showed depth and variations of colour around the bowl. I took photos of it before I started the cleanup process. The bowl itself was quite clean with just a minimal cake on the walls of the bowl. I took photos of the rim top to show how clean it looked and the condition of the top and edges of the bowl. The vulcanite saddle stem surface had some scratches and tooth marks and chatter on both sides ahead of the button.The stamping on the smooth band around the shank read “MALAGA” on the underside. I removed the stem from the shank and took a photo of the look of the pipe. I would need to bend the stem slightly to match the flow of the bowl.Before I started working on the pipe itself I went back and reread what I had found when I had worked on many of the Malaga pipes that had come across my work table. I am including a few pieces of information that I have gathered in the process.

I started my work on the pipe by reaming the bowl with a PipNet reamer. I used the first cutting head and took the cake back to bare briar. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife and removed all the remnants of the cake. I scraped the rim top with the flat edge of the blade at the same time and removed most of the thick lava build up. I sanded the walls of the bowl with a piece of dowel wrapped in 220 grit sandpaper. The walls look very good at his point in the process. I cleaned out the shank, the airway and the mortise as well as the airway in the stem with alcohol, cotton swabs, hard bristle and soft bristle pipe cleaners. It was actually quite clean, which made me think that the seller had done a good cleanup job on the pipe.I scrubbed the exterior of the bowl and shank with a tooth brush and undiluted Murphy’s Oil Soap. I scrubbed the lava on the rim top and overflow on the outside of the bowl with the soap. I rinsed the briar with warm water to remove the grime and debris of the scrubbing. It looked significantly better after the scrubbing. Once I cleaned the bowl with the soap it looked much better. I rubbed the bowl and shank down with Before & After Restoration Balm to deep clean the finish on the bowl and shank. The product works to clean, enliven and protect the briar. I worked it in with my fingers and a horse hair shoe brush to get it into the briar. I let it sit for 10 minutes then I wiped it off and buffed it with a soft cloth. The briar really began to have a rich shine. I took some photos of the bowl at this point to mark the progress in the restoration. It is a beautiful bowl. With the bowl finished I turned my attention back to the stem. I heated the bite marks in the stem surface with a heat gun. I was able to raise some of them significantly. I also heated it enough to bend the stem to match the angles on the bowl. Once I had them bent to the right angle I set the bend with cold water. I took photos of the newly bent stem and the look on the bowl. I filled in the remaining tooth marks with extra strength, rubberized black CA glue. I set the stem aside and let it cure. Once it cured I flattened the repairs with a small file. I continued to blend it into the stem surface with 220 grit sandpaper. Once I finished the blending the stem surface looked much better. I sanded the surface of the stem with the 2 x 2-inch sanding pads – 320-3500 grit pads to clean up the sanding marks on the stem surface. By the final 3500 grit pad the stem started to really shine.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I wiped the stem down after each sanding pad with Obsidian Oil. I gave the stem a final polish with Before & After Pipe Stem Polish both Fine and Extra Fine. I rubbed the stem with them and then gave them a final coat of Obsidian Oil. I set it aside to dry. This is a beautiful Wire Rusticated “Malaga” Bent Billiard with a vulcanite saddle stem. It has a great look and feel. The shape of the bowl, the rusticated rim top and the cut of the briar work well to highlight the beauty of the pipe. I polished stem and the bowl with Blue Diamond polish on the buffing wheel. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The rusticated briar took on life with the buffing. The rich colour of the stain works well with the polished vulcanite stem. The finished pipe has a rich look that is quite catching. Have a look at it with the photos below. The shape, finish and flow of the pipe and stem are very well done. The dimensions are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 2.19 ounces/62 grams. It is a beautiful pipe. I will be putting it on the rebornpipes store shortly in the American Pipemakers Section if you are interested in adding it to your collection. Thanks for walking with me through the restoration.

As always, I encourage your questions and comments as you read the blog. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipe men and women who hold our pipes in trust until they pass on into the trust of those who follow us.

What Great Bones on this Lightly Smoked Sandblast Nosewarmer Billiard

4 Replies

blog by Steve Laug

This interesting sandblast sandblast Bent Billiard Nosewarmer pipe was purchased on 04/20/25 on Facebook marketplace from Portland, Oregon, USA. It is a natural sandblast briar with great grain around the bowl and shank. The stem is an acrylic saddle stem. The natural sandblast finish was quite clean even with the light dust and hand oils on the surface. The bowl was lightly smoked and had a faint aroma of tobacco in the bowl and shank. The rim top was quite clean and the inner and bevelled edge looked very good other than a bit of darkening on the bottom edge. The pipe is stamped on the left side of the shank and has crossed bone and rabbit ears [over] and arched BONES. The acrylic stem had no stamping on the sides. It had scratches, light tooth marks and chatter on both sides ahead of the button. It was really an interesting sandblast with twists and turns in the briar. I took photos of it before I started the cleanup process. The exterior of the pipe was soiled with oils and dust but still looked very good. The rim top was in very good condition. The bowl itself had a was quite clean but there was darkening and a faint smell of tobacco. The acrylic taper stem surface had some light scratches and marks on both sides.I took a photo of the stamping on the left side of the shank. It is clear and reads as noted above. I also removed the stem and took a photo of the parts of the pipe. It is a great looking pipe.I took a few moments before working on the pipe to do a bit of research on the Bones pipes line. I knew they were made by Morgan Pipes so I started there. I looked up the Morgan Pipes site (https://morganpipes.com/collections/bones) and quote from there:

Bones Pipes are pipes – That’s it – No fancy stuff… If you want a pipe to start with or just build your collection, Bones are the pipes for you. Toss it in a tackle box or a backpack and go. These pipes are, simply put, the absolute least expensive honest briar pipe on the market. A simple smoking machine.

I Googled and found a great link to Cupojoes tobacco shop (https://www.cupojoes.com/tobacco-pipes/morgan-bones/). They had a great description of the line from the perspective of the seller. I have included that below.

Chris Morgan began making pipes in 2006, and has since become renowned name within the pipe smoking community. The reason being: the world famous Bones Pipe. The Bones pipe is exactly what it sounds like, the bare naked skeleton of a pipe, that we often never get a chance to see. While other companies rely heavily on staining and sandblasting techniques, the Bones comes in a truly unfinished, natural beauty, making each one (even if the same shape) unique. Praised for their affordability, Bones pipes are the perfect pipe for travel & on the go, often small enough to fit into pockets. Chris offers other lines such as the impeccably built Black Jack series, and the famous patented cigar style pipe called the “Briar Cigar”.

Now it was time to do my work on the pipe. I cleaned out the airway in the stem and the shank with pipe cleaners – both bristle and normal as well as cotton swabs and isopropyl alcohol.I scrubbed the surface of the bowl and the inside with undiluted Murphy’s Oil Soap and a tooth brush. I rinsed it off with warm, running water. I was able to remove the grim on the bowl sides and the bowl smelled far better. I set the bowl aside and turned my attention to the stem. I polished the acrylic stem with micromesh sanding pads – dry sanding it with 1500-12000 grit pads. I wiped the stem down after each sanding pad with Obsidian Oil and set it aside to dry. I polished it further with Before & After Pipe Polish – using both the Fine and Extra Fine Polishes. I gave it a rubdown with Obsidian Oil one last time and set it aside. I put the Chris Morgan made Bones Sandblast Bent Nosewarmer Billiard back together and worked the stem over on the buffing wheel using Blue Diamond to lightly polish the acrylic stem. I left the pipe natural finished and did not wax or polish it. I gave the stem multiple coats of carnauba wax. I buffed the entire pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The finished the Bones Nosewarmer Billiard is shown in the photos below. The natural sandblast finish works well with the rich black acrylic stem. It looked quite amazing! The dimensions of the pipe are: Length: 4 inches, Height: 1 ¾ inches, Outside Diameter: 1 ¼ inches, Diameter of the chamber: ¾ of an inch. The weight of the pipe is 48 grams/1.69 ounces. This is a sandblast on the bowl and shank that reveals the grain underneath. This one will soon be on the rebornpipes store in the American (US) Makers Section. If you are interested in adding this Bones pipe to your collection this may well be the one for you. Thanks for walking with me through the restoration process.

Restoring a Lightly Smoked Handmade by Erik Nording Bulldog

Leave a reply

by Steve Laug

The next pipe on the table is a lightly beauty. It is dusty and dirty from sitting and smells lightly of tobacco. We purchase it from a seller on Facebook marketplace on 04/30/25 in Portland, Oregon. It is a smooth Bulldog with a diamond shank. The Bullcap top is rusticated to look like plateau. The shank end has a light bevel and the stem is a military style bit. It is stamped on the left underside of the diamond shank and reads Handmade [over] By [over] Erik Nording. There is no shape number stamped on it. There is a light carbon bowl coating and the bowl was clean and had a light smell of tobacco in the bowl which led me to the conclusion that the bowl had been smoked. The rim top and the inner edge of the bowl looked very good. The mortise was also clean with no oils or tars darkening it. The finish on the bowl and shank was dull but otherwise in great condition and the acrylic stem was new looking. There were not any tooth marks or chatter on the top and underside on and near the button. There was a Nording “N” logo stamped on the top side of the stem. I took photos of the pipe before I started my cleanup work. They tell the story and give a glimpse of the promise that we see in this pipe. I took a photo of the rim top and bowl to show the current condition. The rusticated “plateau style” rim top is in perfect condition with no nicks or flaws. The bowl photo shows the light carbon coating on the walls. The walls do not have any tobacco debris or ash on them at all. The stem photos show how clean the stem is other than scratching on the surface.I took photos of the heel of the bowl to capture the stamping. It is faint but readable as noted above but a bit hard to capture in the photos. I removed the stem from the shank and took photos of the overall look of the pipe. It is a beautiful pipe.I turned my attention to the pipe itself. I wiped out the inside of the bowl with a paper towel to lightly remove the dust in bowl coating on the pipe. It looked much better at this point. The bowl still smelled like light tobacco. I am pretty certain the pipe has been lightly smoked. I scraped off the loose coating with a Savinelli Fitsall Pipe Knife. I sanded it smooth with 220 grit sandpaper wrapped around a dowel. The bowl is smooth now but I left a smooth coat on the walls for protection.I cleaned out the shank and airway using alcohol, cotton swabs and pipe cleaners – both bristle and clean ones. The shank was clean though there was some stain from the briar and some light tars and oils that came out of the shank and some bowl coating out of the entry of the airway in the bowl. I cleaned the airway in the stem at the same time and the airway had some tobacco debris and oils that came out.I scrubbed the briar and the inside of the bowl with undiluted Murphy’s Oil Soap and a tooth brush. I rinsed the bowl with warm running water. The bowl was clean and it smelled fresh. I polished the briar with micromesh sanding pads – dry sanding the briar with 1500-12000 grit pads. I wiped the bowl down with a damp cloth to remove the debris left behind by sanding. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I finished hand polishing the stem with Before & After Pipe Stem Polish – both Fine and Extra Fine. I wiped it on with my fingers and buffed it off with a soft cloth. The stem really began to have a deep glow. I gave it a final wipe down with Obsidian Oil and set it aside to dry. I am excited to finish this Nording Handmade Smooth Bulldog with a polished military bit style stem. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with beautiful grain on the sides of the bowl with the black vulcanite stem. This smooth Nording Handmade Bulldog is great looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 49 grams/1.73 ounces. It turned out to be a beautiful pipe. I will be putting it on the rebornpipes store in the Danish Pipe Makers section. If you are interested in adding it to your rack let me know by message or by email to slaug@uniserve.com. Thanks for joining me in my work on this pipe.

Unplugging the airway in a Savoy’s Bent Billiard 710 Bowl

Leave a reply

by Steve Laug

Last week I received an email from my local pipe shop about a pipe that a customer brought in with a plugged airway in the bowl. I wrote and we arranged to have the pipe dropped off for me to work on. It was a small Bent Billiard that was stamped Savoy in an oval on the left side of the shank and the shape number 710 on the right side. Joe from the pipe shop said he thought it had a filter broken off in the shank. We looked at it in the sunlight and I could not tell. When I took it to the worktable I used a bright light to examine the shank further. It was dirty but I could see that the shank had a sump like a Peterson’s bowl and that the airway was drilled at the top of the sump. There was no broken filter in the shank and the pipe was not drilled for one. The shank was plugged in the airway rather than the sump. Now I knew what I needed to do. I fit a small drill bit in the chuck of my cordless drill. I set the drill at a slow speed and pushed the bit through the clog in the airway. It was open. You can see the “crud” on the place mat under the bowl. The plug was composed of rock-hard tars and oils. I cleaned up the bowl with 220 grit sandpaper wrapped around a piece of dowel. There was not much cake in the bowl and it was obvious that it had been recently reamed.The inside edge of the rim was damaged from the reaming and was slightly out of round. I used a piece of folded 220 grit sandpaper to smooth out the edge a bit.I cleaned out the shank and airway in the pipe with 99% isopropyl alcohol, cotton swabs and pipe cleaners – both bristle and regular. It had been cleaned somewhere along the way so I removed the remaining debris from drilling out the clogged airway. I took the bowl to the buffer and buffed it with multiple coats of carnauba wax to protect the briar and give it a shine. I buffed it with a clean buffing pad to polish the wax. I then buffed it by hand with a microfibre cloth to deepen the shine. It is ready to go back to the pipe shop to be reunited with its stem. Here is the finished bowl.

Fitting a stem on an UNSMOKED Freehand bowl from the estate of Byron Harwood

Leave a reply

by Steve Laug

The next pipe I chose to work on was one that we purchased on 12/28/2024 from as part of an estate that belonged to a pipeman and carver, Byron Harwood from Missoula, Montana, USA. This Freehand was one of Byron’s own handmade pipes. It is a lovely piece of plateau briar (rim top and shank end) that was shaped with an apple bowl that highlighted the grain. The bowl and shank were smooth and highlighted some beautiful grain. The airway in the mortise and shank are well executed and the draught is very good. The bowl was unsmoked and other than dusty when we received it, the pipe was in excellent condition. The stem that came with it really did not fit – more of a Lovat style saddle stem on a midsized freehand. It looked like it had just been put in the shank before shipping. Everything about the stem said “restem me” to this repair guy. The pipe fit well in the hand and had a small bowl but there was a charm to it! Here is what it looked like when I brought it home from Jeff’s place. I took some photos of the rim top and bowl to give a clear picture of the condition of the rim top and bowl. You can see the drilling and the plateau. It is an unusual pipe. I also took photos of the stem to show its condition also the general look of it and why I don’t think it is a good fit.I sanded the briar bowl with 320-3500 sanding pads. I wiped the briar down with a damp cloth after each sanding pad. It began to look very good. I polished the bowl with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping it down after each sanding pad with a damp cloth. The grain of the briar began to shine. I worked some Before & After Restoration Balm into the surface with my finger tips. I let it sit on the bowl for 10 minutes and then buffed it off with a paper towel and soft cloth. The product is a great addition to the restoration work. It enlivens, enriches and protects the wood while giving it a deep glow. It is a product I use on every pipe I restore. I went through my stems and found an acceptable acrylic saddle stem. It had been used for a short time and the airway was stained with dark tobacco stains. I would be able to remove some of the stain but not all. I took a photo of the two stems together. I put it in the shank of the bowl at hand and took a photo of the look with a new stem. The combination works very well.I cleaned the airway in the stem with alcohol and pipe cleaners – smooth and bristle. I followed up on that by cleaning it again with Soft Scrub cleanser. I gave it a quick rinse of alcohol to remove the residue of the cleanser and the swirls of tans, creams, ivory, browns and black look very good. There is some heavy darkening stain that I cannot remove but the stem is very clean.I set the bowl aside and worked on the stem. I filled in the tooth marks in the acrylic with clear CA glue. Once they cured I flattened the repairs with a small file and then sanded the repairs smooth with 220 grit sandpaper. I sanded out the light tooth marks and chatter with 320-3500 grit sanding pads. I wiped the stem down with an Obsidian Oil cloth after each sanding pad. The stem looked better at this point.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I buffed the stem with a soft cloth to raise the shine. I gave it a final wipe down with Obsidian Oil to add shine to the acrylic. I don’t know what it is about finishing a restoration but I have to tell you that it is my favourite part of the process. It is the moment when everything that I have worked on comes together. I can compare it to where I started and there is always satisfaction that it does indeed look better than when we picked it up. As always, I put this Byron Harwood Freehand Apple and new stem back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad and hand buffed it to raise the shine. It is fun to see what the polished bowl looks like along with the polished clear acrylic stem. This Byron Harwood Freehand Apple is a great looking pipe and I am sure that it will be comfortable in hand when smoking as it is light and well balanced for a pipe of this size. Have a look at it with the photos below. The dimensions are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 2.26 ounces/64 grams. It is another beautiful pipe and one that will be on the rebornpipes store soon. You can find it in the section of Pipes by American Pipe Makers. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.