Bringing a Stanwell Jubilee Sixten Ivarsson Design 10M back to life

Blog by Steve Laug

The next pipe in the lot that my brother brought back from the recent estate sale was a beautiful little Stanwell Acorn with a vulcanite shank extension. The pipe had some nice birdseye on the left side of the bowl and shank and a mix of grain around the rest of the bowl. The point at the bottom of the bowl has a ring of grain with a centre at the bottom and turning around the bowl up the front and back of the underside of the shank. The pipe is stamped on the left side of the shank Stanwell over Regd. No. (an illegible number) over Jubilee. On the right side it is stamped 10M which is the shape number. The shape is a design by Sixten Ivarsson that was done for Stanwell. It has a military mount stem. The Stanwell Crown S in on the shank extension rather than on the stem. The photos that follow are one that Jeff took of the pipe before he cleaned up to send to me.Jeff took close up photos of the rim and the bowl to show the condition. There was a light cake in the bowl with an overflow of lava on the crowned rim top. The next two photos show the grain on the sides of the bowl. The third photo shows the ring at the bottom of the bowl radiating up the bowl sides. It is a beautifully grain piece of briar that the shape fits very well. The next two photos show the stamping on the sides of the shank. The left side shows the Stanwell stamp clearly as well as the Jubilee stamp. It also shows the Crown S on the shank extension. There is a Regd. No. that is very faint and unreadable.The stem had the now familiar tooth chatter and marks the top and underside near the stem. The dents/marks on the underside were worse than those on the top side.My brother cleaned up the pipe as he usually does before he sends it to me. He did an amazing job cleaning up the interior and the exterior. When the pipe arrived in Vancouver it was absolutely clean on the inside. He had cleaned out the mortise and the airway in the shank and the stem with alcohol, pipe cleaners and cotton swabs until it was spotless. He had scrubbed exterior with Murphy’s Oil Soap and removed all of the grime on the bowl sides and the lava build up on the rim. I took the next four photos to show what the pipe looked like when it arrived here. The finish looked really good. The shank extension and stem were lightly oxidized. I took a close up photo of the rim to show how well it cleaned up. There was some darkening on the rim top. The grain really stood out well on the crowned rim. The inner edge of the rim was in excellent condition.I took some photos of the stem top and underside to show the oxidation and the tooth chatter and marks on the surface near the button.I sanded the shank extension with micromesh sanding pads to remove the oxidation. I wet sanded it with 1500-2400 grit pads and dry sanded with 3200-12000 grit pads. I buffed the shank extension and the bowl with Blue Diamond on the buffing wheel to polish the vulcanite. I use an acrylic paint to fill in the Crown S on the left side of the shank extension. Once the paint dried I buffed it off with Blue Diamond to remove the excess paint and leave some in the stamped impression in the vulcanite. There is still some oxidation in the vulcanite of the extension that needed to be polished out but the buffing would take care of that. The photos tell the story.I sanded the stem with 220 grit sandpaper to remove the oxidation on the surface. I followed that by sanding with 320 grit sandpaper to remove the scratches. I polished the stem with 1500-2400 grit micromesh sanding pads. I rubbed the stem down with Obsidian Oil. I dry sanded it with 3200-12000 grit pads and gave it a rub down with Obsidian Oil after each pad. I buffed it with Blue Diamond between the 2400 and 3200 grit pads and between the 4000 and the 6000 grit pads. I gave it a final buff after the 12000 grit pad and gave it a final coat of Obsidian Oil and set the stem aside to dry. I put the stem back in the shank extension and buffed the pipe with Blue Diamond polish on the buffing wheel. I buffed it until the remaining scratches and oxidation were gone. The grain really began to stand out as I buffed the pipe. I gave it multiple coats of carnauba wax to protect the briar and the vulcanite. I buffed it with a clean buffing pad to raise the shine. I hand buffed it with a microfibre cloth to deepen the shine. The finished pipe is shown in the photos below. It is a beautifully grained pipe that is laid out well with the piece of briar. The dimensions are Length: 5 ¼ inches, Height: 2 inches, Outside bowl diameter: 1 ½ inches, Chamber diameter: ¾ inches. It is a pipe that I would normally hang on to for my own collection but I have a similar one already so I am going to put it on the rebornpipes store. It is available to anyone who wants to add it to their collection, their pipe rack. Just let me know if you are interested. Email me at or send me a private message on Facebook. Thanks for looking.


2 thoughts on “Bringing a Stanwell Jubilee Sixten Ivarsson Design 10M back to life

  1. Jesper Nielsen

    What a beautiful renovation of a beautiful pipe.
    The reg. no. is always 969-48. The name “Stanwell” was registered with the Danish authorities in 1948 and the no. was 969.
    Would you do me a small favour and spell the designer’s name right..? It is Ivarsson, not Ivarrson.

  2. upshallfan

    Wow, that one almost wants me to become a Stanwell collector! What a legendary shape, that one should move quickly!


Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.