Tag Archives: vulcanite

Easy Cleanup of a Nice Large Bowled Gourd Calabash

Leave a reply

Blog by Steve Laug

Yesterday I received a box of pipes that Jeff had cleaned up and sent to me. It is a nice assortment of pipes that should be fun to work on. In the box were three unsmoked, NOS Meerschaum bowled Gourd Calabash pipes. I lined them up and took a photo of them that I have included below. The vulcanite stems are lightly oxidized and the meerschaum is dull and needing to be polished but otherwise they are in perfect condition. The top two are smooth calabashes and the bottom one is etched/rusticated. I will start my polishing work and go through them in the order below.The calabash at the top of the above photo is the largest of the three pipes. Its measurements are Length: 7 inches, Height: 4 ½ inches, Diameter of the meerschaum cup: 3 inches, Diameter of the chamber: 1 inch, Depth of the chamber: 1 ¼ inches. I took photos of that pipe before my polishing work. I took photos of the cup to show the cleanness of the bowl. It is a little scratched which I will polish out. The stem is lightly oxidized but unmarked by tooth chatter or marks. It should clean up easily and allow whoever takes it in trust to put their own teeth marks on it.     I took the pipe apart and took a series of photos to show its condition and the overall appearance of the pipe. You can see that the cork gasket it dry and lifeless and needs to be rejuvenated. I used some Vaseline Petroleum Jelly to rejuvenate the cork gasket in the bowl. I worked it into the cork with my finger tips to soften the gasket. Once it had absorbed a bit it would be soft and hold the meerschaum bowl in the gourd easily.I polished the meerschaum cup/bowl with micromesh sanding pads – polishing with 1500-12000 grit pads and wiping them down with a damp cloth after each pad.    I put the meerschaum cup in the gourd calabash bowl and took photos of this portion of the restoration of this pipe. I set aside the bowl and turned my attention to the stem. I polished the stem with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. I polished it further with Before & After Pipe Stem Polish – both fine and extra fine.     I really enjoyed putting this pipe together and restoring it because I love the final touches that make it sing. I put the Gourd Calabash back together and lightly buffed the bowl with Blue Diamond on the buffing wheel. I gave the gourd and stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. It is fun to see what the polished meerschaum bowl looks like with the smooth finished gourd and the black vulcanite stem. This richly finished Gourd Calabash is light weight and ready for you to load up a tobacco of preference and enjoy smoking it. Have a look at it in the photos below. As noted above, its measurements are Length: 7 inches, Height: 4 ½ inches, Diameter of the meerschaum cup: 3 inches, Diameter of the chamber: 1 inch, Depth of the chamber: 1 ¼ inches. The weight of the pipe is 146grams/5.15oz. This is one that will go on the Meerschaum Pipemakers section of the rebornpipes online store shortly. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next generation.            

Replacing a Broken Tenon on a Karl Eric Wenhall Langelinie Danish Freehand

Leave a reply

Blog by Steve Laug

Just before Christmas I received an email from Trevor who caught my attention with the back story of a pipe that he wanted to know if he could buy a replacement stem or have me custom fit one for him. He sent me the following email about the pipe that was a bit of a family heirloom from his late grandfather.

I inherited my grandfather’s pipe and the tip of the stem broke off. I don’t know much about tobacco pipe maintenance (so please be forgiving if this is stupid), but I can’t figure out where to buy a replacement stem online or if I have to send it to you to have a custom one made. The markings on the back say “Wenhall Langelinie // Freehand Made In Denmark”.

I have pictures that I can send you if that helps.

My grandfather passed about 8 years ago, so this is a very special heirloom for me as it carries many memories with it. Many thanks in advance.

We exchanged emails and he sent photos of the pipe which I lost in a recent computer break down. The end of the story is that I had him send me the pipe and it arrived here in Canada this week. I opened the nicely packed  box and took out the bowl, the stem and the broken tenon and took some photos of it. Everything about the pipe said Danish Freehand and from the shape and stain I was guessing that it was carved by Karl Erik Ottendahl of Karl Erik pipes. I took photos of the plateau on the rim top and the shank end. It really is a beautiful looking pipe.The stamping on the underside of the shank is clear in the picture below. It reads Wenhall [over] Langelinie [over] Freehand [over] Made In Denmark.I turned to Pipedia to confirm my suspicions about the pipe being made by Karl Erik Ottendahl (https://pipedia.org/wiki/Wenhall). I quote the article below. Note the section highlighted in red at the end of the article about Karl Erik. Also interesting is the connection to Micahel Kabik and Glen Hedelson who we have seen before with other pipes (Sven-Lar Freehands).

Wenhall Pipes Ltd. was a distribution company out of New York City.

By the end of the 1970’s Wenhall approached Michael Kabik and Glen Hedelson, at that time operating from a farm house in Glen Rock, Maryland to create a line of freehands called Wenhall. The situation was favorable, because Kabik & Hedelson had ended their cooperation with Mel Baker of Tobak Ltd. to produce the famed Sven-Lar freehands shortly before.

Upon Wenhall’s offer the partners got a bank loan and set up a studio of 2000 square feet in a fairly new industrial park in Bel Air, Maryland and took on the name Vajra Briar Works. Wenhall initially wanted 500 pipes a week! But Kabik & Hedelson doubted that they could move that much product and told them they would produce 250 pipes per week. Happily, some of the old crew from Sven-Lar joined them at Vajra Briar Works, and thus they rather quickly met the production demands.

Furthermore during this time, Wenhall requested to create a line of pipes consisting of 12 different shapes. The line was called The Presidential and, while they repeated the same 12 shapes for this series, each one was freehand cut. Although they came up with interesting designs, mainly developed by Hedelson, especially Kabik was never really happy with the line or the concept, but, by this time, they had nine people on full-time payroll.

The stint with Wenhall lasted a couple of years, at which time they asked them to join Wenhall in a move to Miami, Florida. But by this time Kabik and Hedelson felt very uncomfortable with the owners of Wenhall and decided that they’d rather close the shop than make the move. Time proved that decision very wise, as Wenhall folded shortly after the move. All the same they had to close Vajra, but scaled down to the two of them and moved the operation to the farm house Glen was currently living in.

Presumptively for a shorter period only Wenhall had pipes made in Denmark by Karl Erik. (BTW K.E. Ottendahl ceased all sales to the USA in 1987.)

Wenhall also distributed pipes from Italy. By unconfirmed information Gigi and Cesare Barontini were mentioned as suppliers.

Now it was time to work on the pipe itself and replace the broken tenon with a new one and give the pipe a new life. In this case I will not do anything intrusive to remove tooth marks or even the potential tobacco smells as they are a part of the memory of Trevor’s Grandfather.

I started the work on the new tenon by flattening out the end of the stem which still had sharp fragments for the previous tenon. I used a Dremel and sanding drum to flatten out the end of the stem. I always do this to prepare for drilling out the stem to receive the end of the new tenon. The second photo below shows the replacement tenon that I have chosen for the stem. It is a threaded Delrin tenon and will need to be modified to get a proper fit. I will also need to reduce the diameter of the tenon for a snug fit in the shank.I drilled the end of the stem with my cordless drill. I started with a bit slightly larger than the current airway in the end of the stem. I worked my way up to one that would allow me to insert the threaded portion of the tenon in the stem. I would need to remove a lot of the threads on the tenon end leaving just grooves for the glue to bite. I used the Dremel and sanding drum to reduce the diameter of the portion of the tenon that fit in the mortise and for removing the diameter of the portion that would be inserted in the newly drilled stem. I checked it throughout the process of sanding to make sure it would fit in both places. Once the fit was right I coated the end of the tenon that would be inserted in the stem with a coat of the Locktite 390 CA glue and pressed it in place in the stem. I turned it to make the alignment with the mortise correct. I would need to do some adjustments to the tenon diameter once the glue cured. Once it was glued I set it aside to let the repair cure.I smoothed out the slight ridge at the junction of the new tenon and the stem with sand paper and filled in the dip with black Locktite 380 rubberized CA glue. Once it cured I used an oval file and sandpaper to reshape that area and give the transition more flow. I scrubbed the oxidation on the stem with Soft Scrub and cotton pads to remove the oxidation on the stem. It took a lot of elbow grease to remove it but it definitely looked better at this point.I polished the stem with micromesh sanding pads. I sanded with all 9 of the pads from 1500-12000 grit to further remove the oxidation and polish the vulcanite. I wiped the stem down after each sanding pad with Obsidian Oil to protect the surface. I finished polishing with Before & After Stem polish – both fine and extra fine. I gave the stem a final coat of Obsidian Oil and set it aside. I worked some Before & After Restoration Balm into the surface of the smooth briar with my fingertips and into the plateau with a horsehair shoe brush. The product works to clean, enliven and protect the briar. I let the balm sit for about twenty minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. This beautiful hand carved Karl Erik Wenhall Langelinie Danish Freehand was a fun pipe to work on and I really was looking forward to seeing it come back together again. With the new tenon on the stem and the stem refreshed and the briar treated with Restoration Balm. I put the stem back on the bowl and gave the pipe a quick and careful buff with Blue Diamond on the buffing wheel. I carefully avoided the stamping on the shank and stem during the process. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad on the buffer. I hand buffed the pipe with a microfiber cloth to deepen the shine. The rich natural finish on the bowl looks really good with the polished black vulcanite stem. It is very well done. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 ¾ inches, Outside diameter of the bowl: 2 inches, Chamber diameter: 1 inch. The weight of the pipe is 64grams/2.26oz. Thanks for walking through the restoration with me as I worked over another beautiful pipe. I will be sending it back to Trevor by the end of the week. I look forward to hearing what he thinks when he has his grandfather’s pipe in hand. If you want to add it to your collection send me an email or a message! Thanks for your time.

Next on the table is an Edward’s Algerian Briar 706M5 Prince

1 Reply

Blog by Steve Laug

Courtesy Doug Valitchka

The next pipe on the work table is an Edward’s pipe that we bought from a fellow in Los Angeles, California, USA. It is a classic Prince in terms of the flow of the stem and shank. The bowl had a thick cake and lava overflow on the rim. It was hard to estimate the condition of the rim top with the cake and lava coat but I was hoping it had been protected from damage. The bowl was smooth and a natural finish. The finish was dusty and tired but had some nice grain under the grime and the finish appeared to be in good condition. There were small fills all around the right side of the bowl. A lot would be revealed once Jeff had worked his magic on it. The stem was dirty but came with tooth chatter and deep tooth marks near the button on both sides. Jeff took photos of the pipe before he started his cleanup work. Jeff captured the condition of the bowl and rim top with the next series of photos. You can see the work that is ahead of us in the photos. The cake is very thick and heavy. The rim looked like it might have some damage on the back inner edge of the bowl. The next two photos of the stem show the top and underside of the stem. It is oxidized and calcified an you can see the tooth marks and chatter on the surface of both sides. Jeff took some great photos of the sides of the bowl and heel showing what is underneath the grime and debris of time and use. You can see the fills in briar on the right side. It will be interesting to see what happens as the pipe is cleaned and restored. He captured the stamping on the sides of the shank. They are clear and readable. The left side reads Edwards. On the right side it reads Algerian Briar 706M5.I turned to Pipedia to have a look at a bit of history on the brand and refresh my memory of the pipe line (https://pipedia.org/wiki/Edward%27s). I quote the article in full below.

Edward’s pipes were originally produced in Saint-Claude, France when Francais actually was a world-class pipe maker with longstanding business & political connections to Colonial Algeria that allowed them to obtain the finest briar.

During the tumultuous 1960’s, Edward’s created a business model to offer the finest briar available in both Classic and Freehand shapes – all at a fair price. They bought the company & equipment and cornered the market on the finest, choice Algerian Briar just before the supply vanished in political turmoil of Algeria’s independence. Edward’s packed up both machinery and briar-treasure to America, safely caching the essentials to create a new pipe-making dynasty. This was a coup, for the 70’s and 80’s were grim years for pipe smokers as quality briar all but disappeared.

Edward’s Design Philosophy is hard to pin down, think of their style as the “American Charatan” with unique & clever twists all their own. Today, they fashion pipes in several locations across the USA. All of Edward’s pipes are Algerian Briar – a fact very few pipe companies can claim, and all are oil-cured utilizing natural finishes – no strange concoctions are used to interfere in your tastebud’s dance with the briar. Algerian, Calabrian, Sardinian, Corsican – take your pick, but Algerian Briar is generally considered the finest smoking briar ever used. When combined with oil-curing, Algerian takes on a magical quality that even Alfred Dunhill recognized as far back as 1918 as the choice for both his Bruyere and Shell.

Now it was time to work on the pipe. I took it out of the box from Jeff and looked it over. It was amazingly clean and looked like a different pipe. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The bowl looked very good. Jeff scrubbed the stem with Soft Scrub to remove the grime and soaked it in Before & After Deoxidizer. When he took it out of the soak it came out looking far better. I took photos before I started my part of the work. I took some photos of the rim top and stem. The rim top is clean but there is a lot of damage to the inner edge on the front half of the bowl. The bowl itself looks very clean. The close up photos of the stem shows that is it very clean and the deep tooth marks are very visible. It almost looks as if the  previous owner had lightly carved grooves to emulate a dental bit on the top of the stem.I took photos of the stamping because they had cleaned up very well.I removed the stem from the shank and took a photo of the bowl and to give a sense of the proportion of the pipe. It is a classic Prince for sure.I decided to take care of the damage on the rim top and inner edge first. I worked over the inner edge with a folded piece of 220 grit sandpaper and repaired the existing bevel to obscure the damage to the edge. Once I had finished the bowl was round and the edge looked very good.I polished the briar and the shank with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I was able to blend in the repairs into the side of the bowl. I wiped the bowl down after each pad with a damp cloth. The grain really began to stand out and the finish took on a shine by the last sanding pad. The photos tell the story! I worked some Before & After Restoration Balm into the surface of the smooth briar with my fingertips. The product works to clean, enliven and protect the briar. I let the balm sit for about twenty minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned to deal with the stem. I “painted” the surface of the stem with the flame of a Bic lighter to lift the tooth marks on the underside and grooves on the top side. I was able to lift most of them significantly. The few that remained I filled in with Loctite 380 CA glue. Once it had hardened I sanded it with 220 grit sandpaper and 400 grit wet dry sandpaper to blend it into the surface of the vulcanite. I polished the vulcanite stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with a cloth containing some Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. One irritation for me is that the repairs of the grooves on the topside with the Loctite 380 CA glue are not quite the same black as the stem surface. Because of that the grooves in the stem show even though they are smooth too the touch!! Arghhh. This oil cured Edward’s Algerian Briar 706M5 Prince was another fun pipe to work on and I really was looking forward to seeing it come back together again. With the grime and debris gone from the finish it was a beauty and the grain just pops at this point. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel. I carefully avoided the stamping on the shank during the process. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad on the buffer. I hand buffed the pipe with a microfiber cloth to deepen the shine. The rich natural finish on the bowl looks really good with the polished black vulcanite stem. It is very well done. Give the finished pipe a look in the photos below. I can only tell you that it is much prettier in person than the photos capture. The dimensions of the pipe are Length: 6 inches, Height: 1  ¼ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 35grams/1.23oz. This is truly a great looking Edward’s. Thanks for walking through the restoration with me as I worked over another beautiful pipe. I will be adding it to the American Pipe Makers section of the rebornpipes store soon. If you want to add it to your collection send me an email or a message! Thanks for your time.

Restoring a Vintage Kaywoodie Standard 93B

4 Replies

Blog by Alex Heidenreich

Introduction:
As I’ve mentioned before, I love Kaywoodie pipes. To me they are The Great American Pipe. In my personal collection and my restoration box, Kaywoodies probably make up at least 50% of each. I work on all kinds of different Kaywoodie pipes, but my favorites are 50s and earlier. In the 50s the Kaywoodie company was sold and in my humble opinion, starting in the 60s the quality control and grading of the briar started to go down. I find far more pits and fills in these more modern Kaywoodies than in the older pipes. So, I was excited when I found this late 40s or early 50s Kaywoodie to restore.

Pipe Details:
Shape: 93B Medium Billiard with Saddle Stem.

History:
Kaywoodie Standard 93B was produced from 1947-1972. This has a 4-hole stinger with the logo on the top of stem. This indicates it is a very early run, as the logo was moved to the side of the stem on most shapes sometime between 1953-1956. That would put this pipe somewhere around 1947-1956. This is the only 93B I have come across that has the logo on the top of the stem. So, I was quite excited to work on it.

Here is a catalog picture from 1955Picture from: https://pipedia.org/wiki/Collector%27s_Guide_to_Kaywoodie_Pipes courtesy ChrisKeene.com

Condition:
This pipe was extremely dirty. There was tons of cake inside the bowl (it was actually formed beautifully indicating this pipe was well loved by its former owner). There was lava all over the top of the bowl. Some darkening was apparent on the rim, but with how dirty it was, it was hard to tell if there was any damage. The outside of the bowl and stem was very dirty. There were some dings and scratches on the outside of the bowl (possibly some road rash). The inside and outside of the stem and the stinger was extremely oxidized. There was also a bite mark on the top of the stem.

Acquisition Pictures:

Restoration:
I took the pipe to my workbench and carefully reamed all of the beautiful cake out of it. I had to use both my reamers and a knife to get it all out. While I was working on this, I put a dab of Vaseline on the logo and dropped the stem into an Oxyclean bath.The below picture shows the reaming complete. Because of the great cake the previous owner had built. The walls of the briar were in really good condition.The top of the rim had lava and build up that was very difficult to remove. I didn’t want to damage the top of the rim, so I avoided using my knife. I just did a quick once over and left it to focus on later.After it was fully reamed, I put two pipe cleaners in the shank then filled the bowl with cotton balls. I used a syringe to soak the cotton balls in alcohol and let it sit for a couple hours.After the bath, I used the cotton balls to wipe down the interior of the bowl. It did help clean it up, but there was still a bit of build up at the bottom of the bowl. I used cotton swabs dipped in alcohol to remove the rest of it and cleaned it up with a bit of sandpaper taped around the back of a Sharpie.At this point I turned my attention to the outside of the bowl. It was very dirty and kept leaving black marks on my hands when I handled it. I also noticed some small dings on the side of the bowl. As I scrubbed the bowl and the rim repeatedly with Murphy’s Oil Soap, the dirt kept coming off. I kept scrubbing and the finish started coming off with the dirt… Well, looks like there is no turning back now. This one would have to be fully refinished. So I just removed the rest of it with alcohol and Acetone. Then I lightly sanded it with 1000 grit sandpaper. With the finish fully removed, I was able to inspect it closely. This pipe had absolutely amazing grain. There were hardly any pits or fills that I could find. The only thing I noticed was the patch of dings on the side. I wasn’t able to raise them with an iron, so I had to patch them with some CA glue. Once the glue had fully cured, I sanded it back down flush.The other side of the pipe has some gorgeous birds’ eye grain.Next, I started working on the stem. I retrieved it from the oxy bath and scrubbed it down with a Magic Eraser. Then I used 600 grit sandpaper to get the rest of the oxidation off. I wrapped the stem in painter’s tape to protect it and used a bristle brush to really clean the stinger. There were some deep tooth marks on the top of the stem. I cleaned them out thoroughly then filled it with black CA glue.Once the glue had cured, I used needle files to remove the excess glue. When it was close to flush, I switched to wet sanding with 400-1000 grit sand paper. After it was sanded flush, I switched to micromesh pads from 1300-12000. Then I rubbed the stem down with Obsidian Stem Oil and set it aside.I turned my attention back to the bowl and sanded it also with the micromesh pads 1300-12000. I had read about Before & After Restoration Balm on Steve’s rebornpipes blog and I just recently acquired some from www.lbepen.com. I was eager to give it a try so rubbed it into the pipe. I could still smell some faint ghosting in the pipe. So, I filled it with Kosher Salt and used a syringe to fill the bowl with 91% Rubbing Alcohol. You can see in the picture below the balm on the pipe as well as the salt and alcohol drawing out the gunk from inside the bowl.I have to say I was pretty impressed with the Before & After Restoration Balm. It worked well to help clean the pipe and enliven the grain. I buffed the pipe with Tripoli, White Diamond and then Carnauba. Here’s another shot of that beautiful Birds’ Eye Grain.Here it is reassembled before I gave it a couple more coats of Carnauba.

Final Pictures:

Breathing Life into a BBB ** 504 Canadian

Leave a reply

Blog by Steve Laug

The next pipe on the work table came to us from an auction in April 2019 in Cynthiana, Kentucky, USA.  The pipe is a classic Canadian shape pipe. The pipe was a mess which probably accounted for how it ended up where it was at a fair price. On the top of the shank it is stamped with the BBB Diamond Logo [over] **. On the underside of the shank it is stamped London, England [over] the shape number 504. The stain is a medium brown is faded and worn looking. The finish was very dirty making it hard to see beyond that to the grain that pokes through underneath. There was a thick cake in the bowl and a thick overflow of lava onto the back of the rim top and edges. It was hard to know at this point the condition of the rim edges. The stem was oxidized and there were deep tooth marks and chatter on both sides just ahead of the button and on the button surface itself. There was no logo or brass BBB triangle on the topside of the taper. Jeff took photos of the pipe before he started working on it. I include those below. Jeff took photos of the bowl and rim top to show the cake in the bowl and the condition of both. It was thick and hard cake with a light lava overflow on the rim top and edges. The inner and outer edges of the rim looked good. He took photos of the top and underside of the stem showing the scratching, oxidation and tooth marks on the stem surface and button. Jeff took a photo of the sides and heel of the bowl to show the condition of the finish – the grime and grit all over the sides and bottom of the bowl. The finish is dirty but you can see the grain through the grime. Jeff took photos of the stamping on the top and underside of the shank. It is faint but readable as noted above.Jeff reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals of the shank and stem with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish on the bowl looked much better. The rim top looked amazingly good with no damage to the edges of the bowl. He soaked the stem in Before & After Deoxidizer bath to remove the oxidation and scrubbed it with Soft Scrub to remove the residual oxidation. The stem looked good and had minor tooth chatter on the surface. When the pipe arrived here in Vancouver for the second stop of its restoration tour it looked much better than when he found it. I took photos of the pipe before I started my work on it. I took photos of the condition of the rim top and stem before I started working. The rim top looks better than before and the edges are in good condition. The bowl is spotless. The stem is in excellent condition with light chatter on both sides.I took photos of the stamping on the sides of the shank. It is faint but readable as noted above.I took the bowl and stem apart and took a photo of the pipe to show the look of the pipe.The pipe was in such good shape that I started my work on the pipe by polishing the briar with micromesh sanding pads. I dry sanded the bowl and rim top with 1500-12000 grit pads and wiped the bowl down with a damp cloth after each pad. The briar really took on a shine by the final pads.    I worked some Before & After Restoration Balm into the finish of the bowl, rim top and shank with my fingertips to clean, enliven and protect it. I find that the balm really makes the briar come alive again. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The bowl really looks good at this point. I set aside the bowl and turned my attention to the stem. I am certain this is a replacement stem as it does not have a BBB logo or emblem on it. The fit is well done and stem is well made. I polished the stem with micromesh sanding pads – wet sanding it with 1500-12000 grit pads. I polished it further with Before & After Pipe Stem Polish – both fine and extra fine.   Once again I am the part of the restoration that I always look forward to – the moment when all the pieces are put back together. I put the BBB ** 504 Canadian back together and buffed the bowl with Blue Diamond. I buffed the stem with a heavier touch with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. It is fun to see what the polished bowl looks like with the smooth finish and the black vulcanite stem. This classic long shank BBB ** 504 Canadian must have been a fine smoking pipe judging from the condition it was when we received it. Have a look at it in the photos below. The dimensions are Length: 5 ¾ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 32grams/1.13oz. This is one that will go on the British Pipemakers section of the rebornpipes online store shortly. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next generation.

Restemming and Restoring a Stone Age K11 609 Italian Freehand Bowl

Leave a reply

Blog by Steve Laug

The next pipe I chose to work on was a bowl sans stem that is interestingly rusticated and reads Stone Age K11 [over] shape number 609 followed by Italy on a smooth panel on the underside of the shank. The shape number reminded me of a Savinelli number but I was not certain. It was purchased in November, 2018 from a fellow in Scottsdale, Arizona, USA. It has been sitting in my box of bowls since that time. Jeff cleaned it up and mailed it to me. It is another pipe that I have been postponing restemming for a while. This morning while going through my collection of stem I found one that fit the pipe. At least it works for me! When I found the stem I pulled the bowl out of the box and set aside to be the next pipe to work on. It has a very unique rustication that is quite different – both rugged and spun that reminds me of a honey swizzle stick. The flared shank and rim top both look like rusticated plateau – faux or real, I am unsure. Overall it is a pretty pipe. The bowl had thick cake in the bowl and the rim top had a coat of lava on the inner edge of the bowl and in the grooves of the rim top. The finish had a lot of dust and debris in the valleys of the rustication. I have no idea who made it but it is definitely interesting. Jeff took some photos of the bowl before he cleaned it up. The next two close up photos show the condition of the bowl and rim top. You can see the thick lava coat on the inner edge of the bowl and in the rustication of the rim top. Jeff took a photo of the stamping on the underside of the shank. It read as noted above and is  clear and readable.I decided to see if could confirm my thinking that the pipe was connected with Savinelli. I turned to Pipephil’s site and found nothing connecting the Stone Age K11 609 to the brand. However I was not convinced as I am sure the shape number 609 is a Savinelli number.

I turned to Pipedia (https://pipedia.org/images/4/41/Sav_Shape_Chart_2017.jpg) and found a shape chart and indeed for the 609 listed as a shape for a bent billiard. I am pretty sure that with a bit of imagination this freehand that I am working on could possibly be construed as a Freehand in a Bent Billiard shape. But I am uncertain. I have included the chart below.I found pipes with a similar rustication on several sites on the internet. Worthpoint, an online auction site (https://www.worthpoint.com/worthopedia/stone-age-italy-k11-603-tobacco-428555927) listed a 603 with the same rustication style and stamping on the underside of the shank. Smokingpipes.com also listed a Stone Age K11 613 Volcano sitter with the same rustication and stamping on the shank that they had sold in the past (possibly as early as 2010 from the photo (https://www.smokingpipes.com/pipes/estate/italy/moreinfo.cfm?product_id=73396).

With those photos and the shape numbers that at least appear to be made by Savinelli it leaves me wondering. The shapes really do not match the shape chart above but the numbers are present. Ah well another mystery!

I turned to work on the pipe itself. Jeff had carried out his usual thorough cleanup of the pipe. He had reamed it with a PipNet reamer to remove the cake and cleaned the reaming up with a Savinelli Fitsall Pipe Knife. He scrubbed the internals of the bowl and stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the externals with undiluted Murphy’s Oil Soap and rinsed the bowl off with running water. The pipe looked very clean when I received it. I went through my can of stems and found turned freehand style vulcanite stem that I thought would work well with the bowl and shank. I took a photo of the combination below. The stem fit the mortise perfectly though the bend to much to work well with the pipe. There were tooth marks in surface of the top and underside of the stem at the button that would need to be dealt with in the restoration. I put the stem in the shank and took some photos of the pipe. The rim top and shank end cleaned up really well as can be seen in the close up photos below. There appeared to be some debris in the grooves of the plateau top of the rim that would need to be dealt with but without the lava coat it was impressively cleaned. The stem looked like it belonged. I already noted the tooth marks and chatter on both sides near the button.I took a photo of the stamping on the underside of the shank. It really is clear and readable. I decided to start my work on restoring the pipe by addressing the debris and darkening on the rim top. I used a brass bristle brush and scrubbed the surface of the rim top and shank end working on removing debris and darkening from the grooves of the plateau and rustication. It looked much better than when I started.I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar and the the grooves around the bowl and shank with my fingertips and a horsehair shoe brush. The product works to clean, enliven and preserve the briar. I let it sit for 15 minutes while I worked on the stem. After the time passed I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm.   Now it was time to straighten the bend I the stem to match the flow of the pipe. Instead of using my heat gun I painted the stem surface with the flame of a Bic lighter until the vulcanite became flexible. I straightened it out to the angles I wanted for the pipe. I took photos of the pipe at this point in the process. I removed the stem from the bowl and set the bowl aside. I turned my attention to the stem. I “painted” the tooth marks on both sides of the stem with the flame of a lighter to lift them as much as possible. They all lifted but one on the topside. I filled in the remaining tooth mark with clear super glue and set it aside to cure. Once cured, I blended the repairs into the surface of the vulcanite with 220 grit sandpaper. I started polishing the stem with 400 grit wet dry sandpaper. The stem was looking much better. I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem. This restemmed, rusticated Stone Age K11 609 Italian Freehand is a beautiful looking pipe that combines a rusticated finish with a unique shaped. I may never know for sure if Savinelli made it but I think so! The brown stains on the bowl work well to highlight the finish. The polished turned fancy black vulcanite stem adds to the mix. I put the finished stem on the bowl and buffed it with Blue Diamond on the buffing wheel being careful to not buff the stamping. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished pipe is quite nice and feels great in the hand. Give the finished pipe a look in the photos below. I can only tell you that like the other pipes I am working that it is much prettier in person than the photos capture. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 54grams/1.90oz. It will soon be added to the Italian Pipe Makers section on the rebornpipes store. Thanks for walking through the restoration with me as I worked over another beautiful pipe. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next generation.

Beautification of an American Made Bertram Washington DC Grade 30 Bent Pot

1 Reply

Blog by Steve Laug

The next pipe on the work table came to me from one of our estate purchases. Between us we pick up quite a few pipes for restoration. I try to work them into the restoration queue so that I can keep them moving. We picked up over 120+ Bertram pipes from an estate that a fellow on the east coast of the US was selling. This next one is from that estate – a beautifully grained large Bertram Bent Pot Grade 30 with a taper vulcanite stem. The pipe is stamped on the left side near the bowl and reads 30. Following that it is stamped Bertrams [over] Washington D.C. centered on the shank. The finish had a lot of grime ground into the smooth finish on the bowl around the sides of the bowl. There was some darkening on the backside of the rim top on the back side. The bowl was caked with an overflowing lava coat on the top of the rim, heavier toward the back of the bowl. The edges looked okay other than some potential burn damage on the back inner edge. The stem was lightly oxidized, dirty and had light tooth chatter and marks on the top and underside near the button. There were not markings or a logo on the taper stem. Like the rest of the Bertrams in this lot the pipe had promise but it was very dirty. Jeff took photos of the pipe before he started his cleanup work. He took photos of the rim top and bowl to give a clear picture of the thickness of the cake and the lava on the rim top. The lava was thicker toward the back of the rim and there were remnants of tobacco on the walls of the thickly caked bowl. There were also nicks on the inner edge of the bowl toward the front. He also took photos of the top and underside of the stem to show the chatter and tooth marks. Otherwise the stem is quite clean. Jeff took photos of the sides and heel of the bowl to give a picture of what the briar around the pipe looked like. There is some stunning grain under the grime.     He took a photo of the stamping on the shank. It reads as noted above and is clear and readable. The grade number is on the left side near the bowl and reads 30.As I have worked on Bertrams I have written on the brand and have included the following information. If you have read it in past blogs, you can skip over it. If you have not, I have included the link to Bertram history and information. I would recommend that if you don’t know much about them take some time to read the background. I include a link to the write up on Pipedia (http://pipedia.org/wiki/Bertram). Bertram pipes were based out of Washington DC. They were popular among famous politicians and celebrities of the time. They made many products for them from FDR’s cigarette holders to Joseph Stalin’s favorite pipe. They were considered some of the best America had to offer till they finally closed their doors in the 70s. Bertram graded their pipes by 10s and sometimes with a 5 added (15, 25, 55 etc.), the higher the grade the better. Above 60s are uncommon and 80-90s are quite rare. I have worked on one 120 Grade billiard. I have several blogs that I have written on rebornpipes that give some history and background to Bertram pipes. (https://rebornpipes.com/2015/06/16/an-easy-restoration-of-a-bertram-grade-60-217-poker/). I have included the following link to give a bit of historical information on the pipe company. It is a well written article that gives a glimpse of the heart of the company. http://www.streetsofwashington.com/2012/01/bertrams-pipe-shop-on-14th-street.html#

From this information I learned that all of these Bertrams were made before the closure of the shop in the 1970s. This Bertram Bent Bulldog has a nice mix of grain around the bowl. This pipe has a 30 Grade stamp on it which I am sure explains the quality of the briar. But like many of these Bertrams the Grading system is a mystery to me.

Jeff had cleaned up the pipe with his usual penchant for thoroughness. He reamed the pipe with a PipNet Pipe Reamer and cleaned up the remnants with a Savinelli Fitsall Pipe Knife.  He scrubbed the bowl with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs and pipe cleaners. He soaked the stem in Before & After Deoxidizer and rinsed it off with warm water. He scrubbed the remaining oxidation with Soft Scrub and cotton pads and removed it. I took photos of the pipe once I received it. It looked very good. The rim top had some slight darkening on the back of the bowl and some damage to the inner edge on the front. The inner edge of the rim is out of round from the damage. You can also see the fill on rim top on the right side. The stem surface had some pitting on the surface and some tooth chatter on both sides near the button.    I took a photo of the stamping on the shank. The shape number 30 is followed by the brand stamp Bertram Washington DC is on the left side mid shank.I removed the stem and took a photo of the pipe to give a sense of the whole. The stem is tapered and you can see the pitting in the surface of the stem in the photo below.I started my work on the pipe by cleaning up the inner edge and the rim top with 220 grit sandpaper. I was able to minimize the damage.I polished the bowl and the rim top, sides and shank with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping it down after each pad with a cloth. I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. I set the bowl aside and turned to work on the stem. I sanded the pitted surface smooth with a folded piece of 220 grit sandpaper. I started polishing with 400 grit wet dray sand paper. The quality of the vulcanite is quite high as the sanding dust was not the characteristic brown but was black. It was in very good condition so I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with a damp cloth after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem.   This Bertram Washington DC Grade 30 Large Bent Pot with a vulcanite taper stem is a great looking pipe now that it has been restored. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Bertram 30 Pot fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ½ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: 1 inch. The weight of this pipe is 73g/2.57oz. I will be adding it to the rebornpipes store shortly. It will be in the American Pipe Makers section. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Cleaning up a Great Looking L.H. Stern Sterncrest 266 Bent Apple

Leave a reply

Blog by Steve Laug

The next pipe on the table is one that Jeff picked up from an antique store on the Oregon Coast, USA early in 2019. It has been sitting here for a long time. It is a nice looking bent Apple with great grain. The stem is a taper that looks very good. The stamping on the left side of the shank read LHS in a diamond with Sterncrest [over] the top of the diamond and with Imported Briar under the diamond. On the underside of the shank it is stamped with the shape number 266. The shank had a line around the entirety that appeared to be left behind by a missing band. The finish has great grain that flairs up from the heel of the bowl. It is unique and attractive. There was a lot of grime and grit ground into the finish of the bowl. There was a heavy cake in the bowl  and a heavy overflow of lava on the sandblast rim top. The fit of the stem in the shank was smooth and flawless. On the left side of the stem was a silver diamond LHS logo inlaid on the stem. The stem was vulcanite and it was lightly oxidized, calcified and had some wear on both sides near the button.  Jeff took photos of the bowl and rim top to show the cake in the bowl. The rim top showed thick coat of lava was heavier on the backside and was thick enough that I hoped it would protect the rim edge. You can also see a fill on the back of the bowl toward the top. He took photos of the top and underside of the stem showing the tooth chatter, scratching, oxidation and calcification on the stem surface and wear on the edges of the button.   Jeff took a photo of the heel of the bowl to show the condition of the finish. You can see the well done shape and he amazing grain around the bowl and shank. Even under the dirt and debris of the years it looked very good. The stamping is clear and readable as noted above. You can see the line in the briar from where the band had previously been set. I turned first to Pipephil to get a quick review of the brand (http://pipephil.eu/logos/en/logo-lhs.html). I quote the information listed below.

The L&H Stern Inc. was established by Ludwig Stern (1877-1942) in 1911. His brother Hugo (1872-?) acted as vice-president & secretary. The firm moved to 56 Pearl St. Brooklyn in 1920. It closed down in the 1960s. LHS was one of the main pipe supplier for US soldiers during WWII.

I also did a screen capture of the section on the Sterncrest line. I have included it below. Sure enough the pipe originally had a sterling silver band. I would need to look through my bands and see if I could find a band that would fit the shank.I then turned to Pipedia to have a look at the history of the LH Stern brand and see if there were any pipes like the one in hand (https://pipedia.org/wiki/LHS). There were photos of many different LHS Sterncrest pipes but none quite like this one. The history was worth a read and I have included a summary of that below:

Ludwig Stern, a successful pipe manufacturer since 1893 and closing around 1960, reorganized his company along with his brother Hugo Stern, opening a factory in 1911. They named the company L&H Stern Smoking Pipes & Holders. The newly formed company was moved into a six story building on the corner of Pearl and Waters street Brooklyn, NY.

Thoroughly organized in all departments, and housed in a well-lighted and ventilated modern office and manufacturing building, the firm of L&H Stern Inc. is located near the first arch of the Manhattan bridge, near the river and convenient to the Brooklyn bridge, which makes it accessible from all the hotels in the metropolis for visiting buyers. The structure is six stories with a seventeen-foot basement, with light on three sides through prismatic glass windows, the first floor being seven feet above the sidewalk. Light enters the upper floors from all four sides.

L&H Stern is known to every important wholesaler and jobber in the country. LHS manufactures a complete line of briar pipes. Ginmetto wood pipes are also made, as well as Redmanol goods, the man-made amber. The first substitute for amber. Everything, even down to the sterling silver and other metal trimmings are made under one roof.

With the information I learned in the above articles I had the background on the pipe. Now it was time to work on it.

I am really happy to have Jeff’s help on cleaning up the pipes that we pick up along the way. He reamed the bowl with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks much better and the rim top was actually very visible and it looked good. Jeff soaked the stem in Before & After Deoxidizer bath for several house. He rinsed it off with warm water and clean out the internals. He scrubbed the stem with Soft Scrub All Purpose Cleaner to remove the remaining oxidation on the stem. When the pipe arrived here in Vancouver it looked very good. I took some close up photos of the rim top and the stem surface. The rim top looked very good with a little darkening along the inner edge of the bowl at the back. I took close up photos of the stem to show the condition of the surface and button. The stem was very clean with tooth chatter on both sides near the button. There were some deep scratches on the topside.I took a photos of the stamping on the sides of the shank You can see that it is stamped as noted above. It is clear and readable.I took the pipe apart and took a photo of the pipe. It is a good looking pipe and has some great grain on the bowl and shank.I decided to start my restoration work on this one by polishing the briar with micromesh sanding pads. I worked it over with 1500-12000 grit sanding pads. I wiped the bowl down with a damp cloth to remove the dust. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process.     I smoothed out the marks from the missing band as best I could and readied the pipe shank for a new silver band. I found a sterling silver band in my collection of bands. I smeared the shank end with glue and pressed the band in place on the shank.I wiped the band down with a jeweler’s cloth to remove the tarnish. It did not take a lot to remove the tarnish and when it was finished it looked very good. With that done the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I looked at the worn areas on the stem and decided to sand them out with 220 grit sandpaper and start polishing it with 400 grit wet dry sandpaper.     I polished the stem with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine.   It is fun to come to end of the restoration of the LHS Sterncrest 266 Bent Apple. It turned out to be a nice looking pipe. The finish came alive with the work I had done on it. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with the polished shank ring and black vulcanite saddle stem. It really was beautiful. This LHS Sterncrest 266 Bent Apple is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ½ inches, Height: 1 ½ inches, Outside diameter of the bowl: 1 ¼ inch, Chamber diameter: 7/8 of an inch. The weight of the pipe is 47grams/1.66ounces. It is a beautiful pipe that I will soon put on the rebornpipes store in the American Pipe Makers section. If you are interested in adding it to your collection let me know. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next pipeman or woman.

 

 

Cleaning up a Strange Mixed Finish Nording Bent Billiard

2 Replies

Blog by Steve Laug

The next pipe on the table is one that Jeff picked up from an auction in Bridgton, Maine, USA in November of 2018 for so it has been sitting here for a long time. It is a very different looking bent Billiard with a faux horn shank ring. The stem is a fancy saddle that looks very good. The stamping on the underside of the shank read Nording [over] Made in Denmark. It was sandblasted on the lower half of the bowl and the entire shank. There is a smooth band around the top half of the bowl on the front and both sides. But it is not totally smooth as it appears that the sandblast was sanded in that area. It is unique for sure and oddly attractive. There was a lot of grime and grit ground into the finish of the bowl. There was a heavy cake in the bowl  and a heavy overflow of lava on the sandblast rim top. The fit of the stem in the shank was smooth and flawless. The faux horn shank ring was quite stunning. On the left side of the saddle the “N” logo had been stamped. It was clear and readable but did not have the white colour in it. The stem was vulcanite and it was oxidized, calcified and had some wear on both sides near the button.  Jeff took photos of the bowl and rim top to show the cake in the bowl. The sandblast rim top showed thick coat of lava that filled in the rim top and hopefully protected the edges from damage. He took photos of the top and underside of the stem showing the tooth chatter, scratching, oxidation and calcification on the stem surface and wear on the edges of the button. Jeff took photos of the sides and heel of the bowl to show the condition of the finish. You can see the well done shape and the interesting grain pattern under the sandblast. Even under the dirt and debris of the years it looked very good.The stamping is clear and readable as noted above. The honey coloured finish even looks good under the grime and the pipe really is a Grand Luxe!I turned first to Pipephil to get a quick review of the brand (http://pipephil.eu/logos/en/logo-n2.html). The pipe was carved by Erik Nording. Nording is a prolific carver who continues to make pipes and sell them globally. The  screen capture below shows a Nording with stamping like the one I am working on.I then turned to Pipedia to have a look at the history of the Nording brand and see if there were any pipes like the one in hand (https://pipedia.org/wiki/N%C3%B8rding). The history was worth a read, though there were no photos of the pipe that I had.

With the information I learned in the above articles I had the background on the pipe. Now it was time to work on it.

I am really happy to have Jeff’s help on cleaning up the pipes that we pick up along the way. He reamed the bowl with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The finish looks much better and the rim top was actually very visible and it looked good. There were also remnants of varnish or shellac on the exterior of the bowl (more on the right than front and left side).  Jeff scrubbed the stem with Soft Scrub All Purpose Cleaner to remove the majority of the grime. When the pipe arrived here in Vancouver it looked very good. I took some close up photos of the rim top and the stem surface. The rim top looked very good and the sandblast on the finish was worn but clean. I took close up photos of the stem to show the condition of the surface and button. The stem was very clean with tooth chatter on both sides near the button. I took a photo of the stamping on the underside of the shank You can see that it is stamped as noted above. It is clear and readable.  I took the pipe apart and took a photo of the pipe. It is a good looking pipe and has some great grain on the bowl and shank. I decided to start my restoration work on this one by working to remove the varnish coat. I rubbed the bowl down with acetone on cotton pads to remove the finish. It did not work very well. So I sanded the finish lightly with 1500 grit micromesh sanding pads to break the shiny top coat on the briar. I then wiped it down again with acetone and was happy with the results. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips and a horsehair shoe brush to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process.     With that done the bowl was finished other than the final buffing. I set it aside and turned my attention to the stem. I looked at the worn areas on the stem and decided to sand them out with 220 grit sandpaper and start polishing it with 400 grit wet dry sandpaper. I touched up the N stamp with Rub’n Buff Antique Gold. I rubbed it onto the surface and into the N with a toothpick. I buffed it off with a soft cloth and the look is very good.I polished the stem with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. It is fun to come to end of the restoration of the Nording Mixed Finish Danish Bent Billiard. It turned out to be a nice looking pipe. The finish came alive with the work I had done on it. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine. It is fun to see what the polished bowl looks like with the polished shank ring and black vulcanite saddle stem. It really was beautiful. This Nording made Bent Billiard is nice looking and the pipe feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 inch, Chamber diameter: ¾ of an inch. The weight of the pipe is 52grams/1.83ounces. It is a beautiful pipe that I will soon put on the rebornpipes store in the Danish Pipe Makers section. If you are interested in adding it to your collection let me know. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next pipeman or woman.

 

Breathing Life into a 1958 Dunhill Bruyere 53F/T Group 3 Bent Billiard

Leave a reply

Blog by Steve Laug

The next pipe on the table came to us in a group of pipes that we purchased from fellow in Los Angeles, California, USA. It is a Dunhill Bruyere Bent Billiard that is in good condition. It is stamped both sides of the shank. On the left side it is stamped with the shape number 53 F/T followed by Dunhill [over] Bruyere. On the right side it is stamped with 3 in a circle followed by A for Bruyere next to the bowl. That is followed by Made in [over] England8. Interpreting that stamp it is as follows: The 53 is the shape number for a bent billiard. The F/T signify a fish tail stem. The Dunhill Bruyere is the finish. The8 following the D of England gives the date the pipe was made and identifies it as 1958. The stamping is clear and readable. The age of the pipe and the oils in the finish has given the pipe a rich reddish brown finish. There is also some amazing grain that the shape follows well. The finish was dirty with dust ground into the surface of the bowl and shank. There was a thick cake in the bowl and tobacco debris stuck to the walls of the bowl. The rim top showed darkening and some lava on the surface. The vulcanite taper stem was oxidized, calcified and had light tooth marks and chatter ahead of the button on both sides.  Jeff took photos of the pipe to show what it looked like before he started working on it.  He took photos of the bowl and rim top to show the thickness of the cake and the darkening and lava overflow on the rim top. The photos of the stem show the oxidation, calcification and tooth marks and chatter on the surface on both sides. The photos of the sides and heel of the bowl show the great grain on the pipe. It is a beauty under the grime and dust.  The stamping on the underside of the shank is shown in the photos below. It looks very good and readable. It reads as noted and explained above. The fourth photo shows the white spot on the stem.  I turned to Pipedia’s section on Dunhill Root Briar Pipes to get a bit of background on the Dunhill finishes (https://pipedia.org/wiki/Dunhill#Root_Briar). I quote:

Bruyere

The original finish produced (usually made using Calabrian briar), and a big part of developing and marketing the brand. It was the only finish from 1910 until 1917. A dark reddish-brown stain. Before the 1950s, there were three possible finishes for Dunhill pipes. The Bruyere was a smooth finish with a deep red stain, obtained through two coats, a brown understain followed by a deep red.

There was a link on the above site to a section specifically written regarding the Bruyere finish (https://pipedia.org/wiki/Dunhill_Bruyere). I turned there and have included the information from that short article below.

Initially, made from over century-old briar burls, classified by a “B” (denoted highest quality pipe); “DR” (denoted straight-grained) and an “A” (denoted first quality), until early 1915. After that, they became a high-end subset to the Dunhill ‘Bruyere’. The DR and B pipes, a limited production, they should be distinguished as hand-cut in London from burls as opposed to the Bruyere line which was generally finished from French turned bowls until 1917, when the Calabrian briar started to be used, but not completely. Only in 1920 Dunhill took the final step in its pipe making operation and began sourcing and cutting all of its own bowls, proudly announcing thereafter that “no French briar was employed”.

Bruyere pipes were usually made using Calabrian briar, a very dense and hardy briar that has a modest grain but does very well with the deep red stain.

“Before the 1950s, there were three possible finishes for Dunhill pipes. The Bruyere was a smooth finish with a deep red stain, obtained through two coats, a brown understain followed by a deep red. The Shell finish was the original sandblast with a near-black stain (though the degree to which it is truly black has varied over the years). Lastly, the Root finish was smooth also but with a light brown finish. Early Dunhill used different briars with different stains, resulting in more distinct and identifiable creations… Over the years, to these traditional styles were added four new finishes: Cumberland, Dress, Chestnut and Amber Root, plus some now-defunct finishes, such as County, Russet and Red Bark.”

There was also a link to a catalogue page that gave examples and dates that the various finishes were introduced (https://pipedia.org/wiki/File:Dunnypipescatalog-1.png).I turned to Pipephil’s dating guide to show how I arrived at the date of manufacture for this pipe (http://www.pipephil.eu/logos/en/dunhill/cledat-en1a.html). I am including the chart that is provided there for the dating a pipe. I have drawn a red box around the section. Since the pipe I am working on has a suffix 8 that is raised superscript it points to the 1950+8 line on the chart below.I also turned to John Loring’s, The Dunhill Briar Pipe – The Patent Year and After, to work on understanding the stamping on this pipe. I found information on page 19 of the book. It read as follows:

The remaining single digit numbers (5-9) that do not date to the 1920s date it to the 1940s if there is a patent reference, to the 1950s if there is no patent reference and the date code number is raised and smaller than the “D” of England, and to the 1960s if there is no patent reference and the date code number is level with and the same size as the “D”.

I now knew that I was working on a Bruyere that came out in 1958. The shape of the pipe was a Bent Billiard that Dunhill with a #53 F/T shape number that denoted a Bent Billiard shape with a fish tail taper stem.

I turned to work on the pipe itself. Jeff had carried out his usual thorough cleanup of the pipe. He had reamed it with a PipNet reamer to remove the cake and cleaned the reaming up with a Savinelli Fitsall Pipe Knife. He scrubbed the internals of the bowl and stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the externals with undiluted Murphy’s Oil Soap and rinsed the bowl off with running water. He soaked the stem in Before & After Deoxidizer and once it had soaked rinsed it off with warm water to remove the residual solution. He dried it off and scrubbed it down with Soft Scrub All-Purpose cleaner to remove any oxidation that was still on the stem. The pipe looked very clean when I received it. I took a photo of the rim top to show the condition. You can see that it looks very good after the clean up. The stem came out looking quite good. There are light tooth marks and chatter on both sides near the button but the oxidation was gone.I took photos of the sides of the shank to show the stamping. It is clear and readable as noted above. I removed the stem from the shank and took a photo of the pipe parts to show what I was working with. It is a nice looking pipe.I decided to start the restoration on this one because it was in such good condition by polishing the rim top and bowl with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped the bowl down with a damp cloth after each sanding pad. The briar began to take on a shine.     With the polishing completed I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar with my fingertips. The product works to clean, enliven and preserve the briar. I let it sit for 15 minutes while I worked on the stem. After the time passed I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm.   I set the bowl aside and turned my attention to the stem. I polished the vulcanite with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further polish the stem.   This Dunhill Bruyere 53E/T Group 3 Bent Billiard from 1958 is a beautiful looking piece of briar that has a shape that follows grain. It is a great looking pipe that came out looking even better after the cleanup. The finish on the pipe is in excellent condition. The red and brown stain on the bowl works well to highlight the grain. The polished black vulcanite taper fish tail stem adds to the mix. With the grime gone from the finish and the bowl it was a beauty and is eye-catching. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel being careful to not buff the stamping. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Bruyere 53 F/T Bent Billiard is quite nice and feels great in the hand. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: 5/8 of an inch. The weight of the pipe is 36grams/ 1.23oz. It will soon be added to the British Pipe Makers section on the rebornpipes store. Thanks for walking through the restoration with me as I worked over another beautiful pipe. Remember we are not pipe owners; we are pipemen and women who hold our pipes in trust until they pass on into the trust of the next generation.