Tag Archives: Kaywoodie Drinkless Canadian

Moving another one of my own – a Kaywoodie Drinkless Canadian

Blog by Steve Laug

This is another pipe that I have taken out of my personal collection as I just do not use enough to warrant keeping it. This pipe was one that I kept from a group of pipes Jeff and I purchased long ago and I cannot seem to find any information on where it came from. This beautiful Canadian should have seen more use but it was not used often. If I smoked it I used it solely for Virginia tobaccos so there is no real ghost in the pipe. The airway in the shank and the mortise were quite clean. The smooth finish and rim top were in good condition. There is a small burn mark on the outer edge of the rim on the right side. It is not large but it is present. The finish was a little dull and there were a few small fills on the top and left side of the shank. The stamping on the pipe is very faint and barely readable. On the left side of the shank it is faintly stamped with the Drinkless [over] Kaywoodie. It is only visible with a lens and a bright light. On the right side shape number is not visible at all. The finish is a light brown and with polishing should make the grain show clearly. The rich finish goes well with the oval vulcanite taper stem. The stem is in excellent condition with no tooth chatter or marks on it. I took photos of the pipe before I did my clean up work on it to prepare it for you. I took a photo of the bowl and rim top to verify the description above. The rim top and edges are in great condition with a slight burn mark on the outer edge of the rim on the right side (top of the photo below). I also took photos of the stem surface showing how clean it was on both sides. I took photos of the stamping on the sides of the shank. It is so faint as to be almost unreadable. It appears to read Drinkless [over] Kaywoodie. I took the stem off the bowl and took a photo of the pipe to give a sense of proportion of the pipe. You can also see shape of the pipe and some interesting grain on the briar. The Kaywoodie Patented Drinkless stinger/tenon has been clipped off somewhere along its journey. Now it was time to work on the pipe. The shank and mortise were very clean and a quick run through with a pipe cleaner proved all that was necessary. I polished the rim top and the briar with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I wiped the bowl down with a damp cloth after each sanding pad to remove the dust and debris. I gave the bowl and shank a coating of Before & After Restoration Balm. I worked it into the surface of the briar with my fingertips and a horsehair shoe brush to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned my attention to the stem. I polished it with micromesh sanding pads – 1500-12000 grit sanding pads and water to wet sand the stem. I wiped it down after each sanding pad with Obsidian Oil on a cotton rag after each sanding pads. But I find it does two things – first it gives some protection to the stem from oxidation and second it give the sanding pads bite in the polishing process. After finishing with the micromesh pads I rub the stem down with Before & After Fine and Extra Fine stem polish as it seems to really remove the fine scratches in the vulcanite. I rub the Fine Polish on the stem and wipe it off with a paper towel and then repeat the process with the Extra Fine polish. I finished polishing the stem with a final coat of Obsidian Oil and set the stem aside to let the oil absorb. This process gives the stem a shine and also a bit of protection.  This Kaywoodie Drinkless Canadian turned out to be a great looking pipe. The natural finish on the pipe is in excellent condition and works great with the polished vulcanite taper stem. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Kaywoodie Canadian fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 1/8 inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 36 grams/1.27 ounces. It is a great looking pipe that I will soon be adding it to the rebornpipes store in the American (US) Pipemakers Section. If you are interested in adding it to your collection let me know Thanks for reading this blog and my reflections on the pipe while I worked on it.