Restoring a Pair of Family Era Barling’s Make Pots

Blog by Steve Laug

When I finished the restoration work on a pair of Comoy’s Blue Riband Billiard pipes and sent them back to the owner, Scott in California I received another email in return saying that he had sent me a pair of Family Era Barling’s Make pot shaped pipes. Here is the link to the work on the Comoy’s Blue Ribands (https://rebornpipes.com/2018/09/29/restoring-a-pair-of-comoys-blue-riband-billiards/).

While my Dad was visiting recently I received a package in the mail from Scott in California, US containing the two Barling’s Make pipes. There was a note in the box regarding what he wanted done with the pipes. He wrote:

Here are those two Barling Family Era pipes as promised. As you can see, the larger pipe (1752) should be pretty easy. I’d like to keep the original finish on this one and eve out the colour on the rim to match the rest of the pipe. The smaller pipe (1533) is another story. Looks like a full restoration job here. The stem is seized in the shank, layers of lava over rim char, spot of finish loss on the outside etc. I’ll leave it to you to bring this little beauty back to life.

After opening the wrappings in the well packed box I found the two pipes. I took pictures of both pipes to capture their condition when they arrived. The first set of photos shows the larger 1752 pipe that he said “should be pretty easy”. The finish still had a shine on the bowl and shank. There were some paint flecks on the right side of the bowl. The rim top was in the issue as he had noted. The finish was spotty and there was significant burn damage around the inner edge and some darkening. There was a light cake in the bowl but no overflow on the rim top. The stem fit well in the shank though the shank was very dirty. The stem was oxidized and had light tooth marks and chatter on both sides near the button. I took some close up photos of the rim top and the stem to give a clearer picture of the condition of the pipe. The stem is stamped with the Barling cross on the top of the saddle and with the words Barling over Design. The stamping is legible but the white in the stamping is gone.I took photos of both sides of the shank to show the stamping on the pipe. The left side read BARLING’S arched over MAKE with the shape number 1752 underneath. The right side was stamped EXEXEL. The stamping is indeed Family Era vintage.The next set of photos shows the second Barling’s Make which was far more worn and dirty. The finish dirty and did not have the glow of the other pipe. There was a spot on the left side of the bowl where the finish was chipped. The rim top had a thick coat of lava overflowing from the bowl. It was hard to know if there was further damage to the top surface. There were some nicks in the outer edge of the rim top. The cake in the bowl on this one was thick and rock hard. The stem did not seat in the shank completely and when I looked the shank was very dirty and caked with tars. The stem was more oxidized than the other pipe and had tooth marks and chatter on both sides near the button. I took some close up photos of the rim top and the stem to give a clearer picture of the condition of the pipe. The stem is stamped with the Barling Cross on the top of the saddle and with the words Barling over Design. The stamping is legible but the white in the stamping is gone.I took photos of both sides of the shank to show the stamping on the pipe. The left side read BARLING’S arched over MAKE with the shape number 1533 underneath. The right side was stamped EL. The stamping is indeed Family Era vintage.I reamed both bowls with a PipNet pipe reamer working through the cutting heads to take the cake back to the bare briar so I could check for damage to the interior walls of the pipe. I cleaned up the reaming with a Savinelli Fitsall Pipe Knife and finished with a piece of dowel wrapped in 220 grit sandpaper to smooth out the walls. The first pipe was definitely cleaner than the second. The cake came out easily. The second pipe had a cake that was rock hard and I had to switch between the smallest cutting head on the PipNet and the Fitsall Knife to break through the cake. I worked my way alternating between the two until the bowl was reamed and then sanded it smooth. I scraped the mortise walls of both pipes with a pen knife to remove the buildup of hardened tars and oils. I cleaned out the mortise and the airway into the bowls as well as the airway in the stems of both pipes with alcohol, cotton swabs and pipe cleaners. I have to say that the second pipe was far dirtier than the first. I worked on the rim on the first pipe to clean up the damage. I worked on the inner edge of the bowl with a folded piece of 220 grit sandpaper. I lightly sanded the top of the rim with 220 grit sandpaper. I was able to remove the damage to the rim top and edges. I polished it with 1500-2400 grit micromesh sanding pads. I continued polishing it with 3200-12000 grit pads. I stained the rim top of the first bowl with Maple and Cherry stain pens to match the colour of the rest of the finish on the pipe. It still needs to be polished at this point but it matches the colour of the pipe.I worked on the rim top of the second pipe. I topped the bowl on a topping board with 220 grit sandpaper to remove the thick buildup and the nicks and damage on the surface of the rim. I sanded with micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding it with 3200-12000 grit pads. I was able to remove the damaged areas and leave the rim top clean. There was still some damage and darkening around the inner edge but I have chosen to leave that for now. I stained the rim top of the second bowl with a Walnut stain pen to match the colour of the rest of the finish on the pipe. It still needs to be polished at this point but it matches the colour of the pipe.I took a photo of both pipes together at this point to show the clean bowls and the condition of the rim tops. The colour of each matches the respective bowl. Both still have damage to the inner edge of the bowl. I had not decided how to address that issue. Scott did not want the inner edge beveled at all. I worked Before & After Restoration Balm into the briar of the first bowl with my fingertips to clean, enliven and protect the wood. I let the balm sit for about 20 minutes and buffed it off with a soft cotton cloth. I took photos of the pipe at this point in the process to show what the bowl and rim looked like. I am happy with the stain match on the rim top. The next four photos show the larger and better conditioned 1752 bowl. It looks really good after the balm and buffing. I smoothed out the damaged spot on the finish on the left side of the bowl and restained it to match the rest of the stain. I worked Before & After Restoration Balm into the briar of the second bowl with my fingertips to clean, enliven and protect the wood. I let the balm sit for about 20 minutes and buffed it off with a soft cotton cloth. I took photos of the pipe at this point in the process to show what the bowl and rim looked like. I am happy with the stain match on the rim top. The next four photos show the smaller bowl, the 1533, that was in worse condition than the first. It looks really good after the balm and buffing. I sanded out the tooth marks and chatter on the stem on larger 1752 pipe with a folded piece of 220 grit sandpaper. I forgot to take photos of the stem at this point in the process. I rubbed the stem down with Denicare Mouthpiece Polish to remove as much of the oxidation as possible without damaging the stamping.I polished it with the micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I rubbed it down with Obsidian Oil between each pad. I polished it further with Before & After Pipe Polish – both Fine and Extra Fine. I gave it a final coat of Obsidian Oil and set it aside. With that stem completed I turned to the second stem, the one on the 1533 the dirtier pipe. Upon examination I found that the stem was a twin bore bit. It had the classic “Biteproof” stem on it. And even that feature had not kept it safe from tooth dents and mark. I “painted” the surface of the stem with the flame of a Bic lighter to lift the tooth marks. Once that was finished I sanded out the tooth marks and chatter with 220 grit sandpaper. After I sanded out the tooth marks and chatter on the stem on 1533 pipe I rubbed the stem down with Denicare Mouthpiece Polish to remove as much of the oxidation as possible without damaging the stamping.I polished it with micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I rubbed it down with Obsidian Oil between each pad. I polished it further with Before & After Pipe Polish – both Fine and Extra Fine. I gave it a final coat of Obsidian Oil and set it aside. I filled in the letters on the top and underside of the Barling’s Make stems with a white out pen. The tip of the pen was frozen so I slit a hole in the side of the pen and used the white out to fill the stamping on the stems. I let it cure and harden. Once it had hardened I scraped it off with my fingernail and left the remainder behind in the letters. I still needed to polish the stem and bowl on the wheel with Blue Diamond to remove the small scratches that showed up with the flash. Once that is done the pipe will be ready to send back to Scott in California.I polished the bowls and stems with Blue Diamond to polish out the scratches in the briar and rubber. I gave the bowls and the stems multiple coats of carnauba wax. I buffed the pipes with a clean buffing pad to raise the shine. I hand buffed them with a microfiber cloth to deepen the shine. Both pipes polished up pretty nicely. The original patina on both bowls came alive with the buffing and worked well with the polished black vulcanite stems. Both pipes have a rich look. The finished pipes are shown in the photos below. The first pipe is the one that was in “better condition” when it arrived. I think it is a bit newer than the second one. The shape, finish and flow of the pipe and stem speak well of the Family Era Barling’s Make pipes. The dimensions of the first pipe, shape 1752 are Length: 5 1/2 inches, Height: 1 3/4 inches, Outside diameter of the bowl: 1 3/4 inches, Chamber diameter: 3/4 of an inch. The dimensions of the second pipe, shape 1533 are Length: 5 1/4 inches, Height: 1 1/2 inches, Outside diameter of the bowl: 1 1/2 inches, Chamber diameter: ¾ of an inch. This pair will soon head back to California so that Scott can enjoy them. Thanks for walking through the restoration with me as I worked over this beautiful pair of Family Era Barling’s Make Pipes… now I need get these packed up and back to Scott!

Restoring Life to a Early 20th Century Gitana Depose Apple

1 Reply

Blog by Steve Laug

I was going through boxes of old pipes here, sorting and getting them ready to sell as grab bags. In the process I came across this pipe. It is stamped Gitana in an oval with an L on the left of the oval and G on the right side of the oval. Underneath the oval stamp is the word Depose. There is a polished aluminum band on the end of the shank. The briar is quite nice with birdseye around the bowl. The stem is horn and has a lot of tooth damage next to the button on both sides. There are deep troughs carved by the teeth in the horn material on both sides. The rim had a lot of damage from burn marks and the inner edge had been damaged by reaming with a knife. There was a white waxy substance on the inside of the bowl from the edge down about a ½ inch. There was a light cake in the bowl and some light lava on the bowl top. I took a close up photo of the rim top to show the damage to the inner edge of the bowl from the reaming job. The cake on the bowl sides and the tarry oil on the rim top are also visible. The briar at the top is quite damaged and will take some work to remove the knife cuts and deep gouges in the briar. The stem is also shown with the chewed damage on both sides. I removed the stem from the shank and was a bit surprised by the aluminum system that was inside. The tenon was aluminum and had a bullet shaped cap on the end of it. The cap had a hole in the top that allowed the smoke to be drawn through the airway in the stem. The previous own had wrapped the aluminum portion of the tenon with what looked like aluminum foil to build it up to fit tightly in the shank. The photos below show the tenon and the system. I was unfamiliar with the brand and was surprised by the tenon system. I did some searching online and could find nothing on the Gitana brand or the Gitana Depose brand. I did happen across a similar pipe on Smokingpipes.com. The writer who described the pipe for the site wrote the following which contained some really helpful information. I quote:

We were able to ascertain a little information about La Gitana, which was a French brand created by Chapel Frés…but this relic from the early 20th century still sports its original horn stem, coupled with a novel aluminum tenon arrangement that we can only assume is meant to trap moisture. Although we aren’t sure how well it achieves this, it does do quite well at looking like an old-school James Bond accessory. It fits securely within a cork-lined mortise, which many briars of this period tended to have. https://www.smokingpipes.com/pipes/estate/france/moreinfo.cfm?product_id=196840

From that I learned that the brand was called La Gitana. It was a French made pipe from a company called Chapel Frés. It was made in the early 20^th century and the author had described the tenon system like the one I had. I also learned that the mortise had originally been cork lined to facilitate holding the tenon snuggly in the shank. This was what was missing in the pipe I had and it had been replaced with the foil mess that is seen in the above photos.

Armed with the name Chapel Frés I looked on Pipedia under French Pipe Companies and found the brand there. It stated that it came from that factory and the brand had been founded in 1904 in Saint-Claude, France. Here is the link https://pipedia.org/wiki/Chapel_Fr%C3%A9s.

Armed with that information I started my cleanup of the stem. I scraped away the foil that was wrapped around the tenon. I examined the bullet shaped cap on the tenon and figured out that it unscrewed from the tenon. I cleaned the metal underneath alcohol, cotton swabs, pipe cleaners and steel wool. I cleaned out the airway in the shank at the same time. The tube in the end of the tenon looked clean. I used alcohol, cotton swabs and pipe cleaners to clean out the inside of the bullet cap. I cleaned out the walls in the shank with pipe cleaners, cotton swabs and alcohol. It was a very dirty pipe that once it was clean had an interesting look to it. I cleaned up the inside of the bowl with a Savinelli Fitsall Pipe Knife. I scraped the walls clean of the carbon build up. I sanded the walls of the bowl with a piece of dowel wrapped with 220 grit sandpaper.To remove the damage on the rim top I topped the bowl until the damaged areas were removed and the rim top was clean. I used a folded piece of sandpaper to smooth out the inner edge of the rim and bring it back to round as much as I could. I washed down the exterior of the bowl with acetone on a cotton pad to remove the finish and the grim on the briar. The pipe looked really good at this point. I needed to round down the outer edges to bring it back to the shape it was when I started but for now it was clean. I took a photo of the stamping on the left side of the shank. The stamping is quite readable and clear.The tenon had some sticky substance for the glue on the foil on the tenon end. The tenon and threads still needed more cleaning to remove the oils.I filled in the tooth marks and troughs in the surface of the horn with clear super glue. I set the stem aside to dry.I decided to try to fit a cork in the shank to line it as suggested above. I cut away some of the excess cork from a wine cork I had. I trimmed it down with a Dremel and sanding drum until the diameter was close to the inside of the shank. I drilled it out with a series of drill bits starting small and working my way up to one that was close to the size of the tenon. I sanded down the cork exterior until it was a fit in the shank. I pressed it in place in the shank.I used a needle file to thin down the inner walls of the cork lining. It needed to be very thin to allow the tenon to fit in the shank. I tried to put the tenon in the shank. The fit was still not right. The cork was too thick to allow a fit. I pulled it out of the shank and slid it over the tenon. I sanded it down with sandpaper and files until it was a good fit. I glued the cork on the tenon and let it dry. When it cured I rubbed the cork down with Vaseline to soften it and allow it to slide into the shank. The fit was very good. I took some photos to show what the pipe looked like at this point in the restoration (I had also started the shaping on the bowl top). I polished the briar with micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I wiped it down with a clean cloth after each pad. The grain began to pop and really stand out. Once the glue repairs cured I sanded them with 220 grit sandpaper to smooth out the repairs. I sanded them to blend them into the surface of the horn. I polished the stem with micromesh sanding pads – wet sanding with 1500-2400 and dry sanding them with 3200-12000 grit pads. I wiped the stem down with Obsidian Oil after each pad. I gave it a final coat and let it dry. The following photos show both sides of the stem. I worked Before & After Restoration Balm into the briar and the horn stem with my fingertips to clean, enliven and protect the wood and the horn. I let the balm sit for about 20 minutes and buffed it off with a soft cotton cloth. I took photos of the pipe at this point in the process to show what the bowl and stem looked like. I am happy with the look of the pipe. I polished the bowl and stem with Blue Diamond to polish out the scratches in the briar and horn. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The original patina on the bowl came alive with the buffing and worked well with the polished striated horn stem. The pipe has a rich look. The finished pipe is shown in the photos below. The shape, finish and flow of the pipe and stem work give the pipe a very classic look. The dimensions of the pipe are Length: 5 1/2 inches, Height: 1 1/2 inches, Outside diameter of the bowl: 1 1/2 inches, Chamber diameter: 3/4 of an inch. Thanks for reading this while I worked on it. It was interesting and unusual piece to restore and I really enjoyed the work.

A Challenging Restoration of Vintage Era First Choquin “A Metz”

8 Replies

Blog by Paresh Deshpande

I had been on a short leave to my home town last month and that is where this happened!!!!! Even though there are still a number of pipes from the two of the three inherited boxes of pipes waiting their turn for restoration, curiosity got the better of me and I could not resist the temptations of opening the third box. What happened thereafter is that I had to unpack all the pipes earmarked to accompany me to my work place for restoration in my free time which in turn invited the wrath of my wife who had helped in packing in the first place, and repack the newly selected pipes from the third box!!!!!! In addition to the regular collection of Barling’s, Charatan’s, Comoy’s and other assorted collection, I came across two pipes which caught my fancy!!!!!The pipe on the left bears a football stamp that reads “CHOQUIN” over “A METZ” and the one on the right side simply reads “GBD” (there are other stampings on the silver ferrule, details of which will be highlighted when it comes up for restoration). Both these pipes looked vintage and unique enough that I immediately Facetimed with Mr. Steve of rebornpipes. His admission that he is willing for a trade with me for these two pipes was an indication enough for me to know and understand their uniqueness!!! Thus these two pipes moved to the top of my unorganized and chaotic list of restoration.

The pipe first on my work table is the CHOQUIN. It is a huge pipe with a humongous acorn shaped smooth briar bowl with a steeply raking shank, the end of which is adorned by a fixed sterling silver ornamented ferrule. This similarly designed sterling silver also masks the tenon of the horn stem.The shank and the horn stem are connected by a push-fit type bone extension. The huge acorn bowl shows beautiful, large and loosely packed birdseye grain on the right side while mixed grain adorns the left side. The stummel on the front, back and the shank displays densely packed straight grains. The only stamping that is seen on this pipe is the football stamp on the left side of the shank and reads “CHOQUIN” over “A METZ”. For its age, the stamping is crisp and clear.This time around, before commencing the restoration process, I posted the pictures of this pipe on the Tobacco Pipe Restorers group on Facebook as my next project. In addition to input from my mentor, Mr. Steve, I collected a lot of valuable information from all the knowledgeable stalwarts. From all the input that I have gathered, the flat bottom bowl, the stamping, the sterling silver adornments, the bone shank extension and horn stem, I can safely place this piece as being one of the first A Metz pipes from the 1858 era!!!!!

INITIAL VISUAL INSPECTION
Well, even before I could start my initial visual inspection, I faced the first of the many numerous hurdles that I had to overcome during the restoration of this pipe. The shank extension and the stem would not budge even a millimeter to separate from the shank and the bone extension respectively. I remembered Mr. Steve referring to the technique of freezing the stuck parts in the freezer for a couple of hours for easy separation. I followed his advice and had to put the complete pipe in the freezer for a couple of hours as it could not be dismantled. True enough, the horn stem separated from the shank extension with the application of a little force, but the extension would not budge from the shank!!!! So I went back to Mr. Steve to tap in to his wealth of knowledge and experience. He suggested that I should apply the method of “Hot and Cold” shock treatment in which you gently and carefully heat the stuck part using a heat gun and then get it back in to the freezer. This process may need to be repeated a number of times before the parts separate. Well, I did exactly that, albeit heating with a hair dryer as I did not have a heat gun, and after 3/4 attempts, the extension finally separated from the shank!!!!The first thing that I noticed was that the shank extension and the mortise were completely filled with oils, tars and grime. The shank extension was filled to an extent that a pipe cleaner would not pass through!!!! How very much typical of my Old Man!!!!!!! Through all this muck, just a swipe of the bone extension with a cotton swab dipped in isopropyl alcohol revealed no apparent damage to the shank extension. Cleaning this would need to be a very careful, meticulous, time consuming and a tedious process given the delicate structure of such a vintage bone. Likewise, the tenon also was filled with oils and grime. Air flow through the stem was laborious to say the least!!! Both the upper and lower surface of the horn stem shows significant damage. The lower surface is peppered with 3-4 worm holes with one significantly larger than the other. Thankfully, it had not migrated through the upper surface!!!! The tenon is completely and permanently encased in the sterling silver ornament. The condition of the stummel was an equally horrendous story. Firstly, the rim top is heavily covered in overflowing lava. The overflow is so heavy that it has accumulated over the rim surface in blobs of dried tar and tobacco oil which can be seen in the subsequent pictures. This overflow had not restricted itself to accumulation on the rim top, but has spilled on to the stummel surface covering the stummel in sticky grime which has attracted more dirt and dust giving the stummel a dull and lackluster appearance. The overflowing lava has even accumulated in the junction where the shank and bowl are joined. Some dents and dings are seen on the surface through the overflow and I do not envisage any major issue like the ones I faced while working on an Imperial Yello-Bole Carburetor that I had I restored. However through all this dirt, tar, oil, grime and damage, lovely grains can be seen on the sides and the shank. It will be a challenge to address these issues and make the grains to reveal themselves in all glory. The chamber is no different story!!! There is a thick build up of cake in the chamber. The inner edge of the rim is covered under the thick cake and as such, its condition can be commented upon only after the cake has been scrapped. The outer edge of the rim, however, shows significant damage in the form of dents, dings and deep scratches to the front in 12 o’clock direction. The cause for this damage is….. Oh, forget it, let’s not even go there!!!! The condition of the inner walls of the chamber can be ascertained only after the chamber has been completely reamed devoid of any cake, but I do not foresee any major damages here as the stummel feels solid to the touch and this huge solid piece of briar can sustain some serious damage. You have to feel the stummel in your hand to understand what I am trying to write. It is one heavy and handful of a pipe!!!!The sterling silver ferrule and tenon ornament was black as is typically seen in heavily oxidized silver. However through all this discoloration, delicate, intricate decorative design can be appreciated. This is another pointer towards the vintage of this pipe.THE PROCESS
I started the process of restoration by polishing the sterling silver ornaments at the shank end and tenon with pipe ash as suggested by Mr. Steve. This was followed by reaming the chamber with size two of the PipNet reamer head and progressing through to size four. Yes Sirs, there is no typo error!!! It is indeed PipNet and not a Kleen Reem reamer as you have gotten used to reading in my write ups !!!!!! Mr. Steve has sent me a set along with some beautiful pipes that I had got from him. I followed up the reaming with scrapping the remnants of the cake from the walls, flat bottom of the chamber and the rim top surface with my fabricated knife (Oh, how I long for a Sav Fitsall reaming knife!!! Hope you are reading this Steve Sir). The cake was so hard, that I invariably ended up scratching the flat bottom surface while scraping. Once the cake was reamed back to the bare briar, I used a 150 grit sand paper followed by 220 grit sand paper to remove all the traces of remaining cake and also to smooth the inner walls of the chamber surface. Finally, to remove the carbon dust, I wipe the chamber with a cotton pad wetted with isopropyl 99%. I gently scrapped the rim top surface with a sharp knife. Removing all the cake from the chamber and rim top revealed that firstly, the rim was out of round and secondly was a web of fissures along the internal walls. There was one crack, which showed prominently after a cleanup with Murphy’s oil soap, bothered me and can be seen in the pictures below which has been highlighted by a red circle. I shared these images with Mr. Steve and Mr. Dal Stanton for their opinion as to the extent of damage and further repairs. They too expressed fears that the crack may have migrated through the stummel. Mr. Steve suggested picking the crack on the top of the rim using a toothpick and filling it with CA superglue. I decided that I would address this issue later after further investigations. I cleaned the internals of the shank, shank extension and the stem using hard bristled and regular pipe cleaners, q-tips, shank brushes, all generously dipped in isopropyl alcohol. I had never used such drastic measures like initially cleaning the bone shank extension by carefully inserting a round needle file for creating an opening through which pipe cleaners could pass through for subsequent cleaning. The heap of pipe cleaners and q-tips that are seen in these pictures are just the proverbial tip of the iceberg. I must have gone through an entire packet of 50 of both types of pipe cleaners, in addition to the q-tips and brush cleaning!!!!! To further deep clean and refresh the internals, I used cotton and alcohol soaks. Using a cotton ball to create a wick, I inserted it through the mortise and into the airway. I then stuffed the bowl with tightly packed cotton balls and placed it in bowl filled with rice grains to provide stability. Similarly I made a tight cotton wick and inserted it through the bone shank extension to further remove all the oils, tars and smells. With a large eye dropper, I then filled the bowl and the bone shank extension with isopropyl 99% until it surfaced over the cotton. I refilled the alcohol in a few minutes after it was absorbed into the cotton balls. I put the stummel and the bone shank extension aside for several hours to soak. After some time, the cotton and the wick were soiled. I discarded the expended cotton and wiped the bowl and the bone shank extension with paper towel. To make sure all was clean, I used a cotton bud and pipe cleaner dipped in isopropyl 99% and they came out clean. I cleaned the stummel with undiluted Murphy’s oil soap and Scotch- Brite pad and rinsed the stummel under running tap water. This cleaning helps in bringing to the fore any other damage which could be hidden under all the dirt and grime. Fortunately, there were no major dents, dings or gouges to the stummel. There were a few minor ones which I think would be addressed when I would sand the stummel surface and subsequent micromesh polish. I dried the bowl with a paper towel and soft cotton cloth. Initially I had decided that I would not be topping the rim top and maintain its original profile. However, in order to ascertain if the crack had migrated through the stummel, I decided to top the rim surface. This would also help to address the numerous dents, dings and scratches on the rim’s top surface and also to remove traces of lava overflow. I topped the rim surface on a 220 grit sand paper. Though it is recommended to have a wooden board with the 220 grit sand paper firmly fixed over it, I just keep the sand paper on a flat table top, holding it firmly with my left hand and rotating the stummel rim top over it with my right hand. I have come to realize that this set up gives me lot more freedom of movement, better control and convenience of storage. Fortunately, it was revealed that the supposed crack was superficial and had not migrated through. Staying with the rim, the next issue that I addressed was the inner rim edge. With a folded piece of 180 grit sand paper pinched between my thumb and fore finger, I created a light bevel on the inner edge. This addressed the issue of uneven and out of round inner edge. The damage to the outer edge was addressed to a great extent when I had topped the rim top surface. Whatever little dents and nicks that remained on the outer edge were very minor, though visible, and I decided to let them be.I sand the stummel surface with a 220, 320, 600 and 1000 grit sand paper, in that order, to remove the minor scratches and marks on the rim and stummel surface. I frequently wiped the sanded surface with a moist cloth to remove the briar dust and also to check the progress of my work. Once I was satisfied with the match, I followed it up by micromesh polishing pads, wet sanding with 1500 to 2400 grit pads. Again, I wiped the bowl with a moist cotton cloth after each pad. I used the 3200 to 12000 grit pads to dry sand the stummel to a nice shine. I was disappointed when after all my efforts up to this stage; there were some very minute chips that were visible in pictures. But overall, at this stage of restoration, the entire bowl, rim top surface and shank is looking fresh and clean. Even though some of the dents and chips could not be completely addressed and are visible only on very close visual scrutiny, in my view, they lend this pipe a battle scarred warrior like a character. I rubbed a small quantity of “Before and After Restoration Balm” with my fingers deep in to the stummel surface. What this balm does is it revitalizes the briar wood and breathes a new life in to the briar. It’s amazing to see the transformation as the balm works its magic on the briar wood. I further buff it with a horse hair shoe brush. Turning my attention to the horn stem, I cleaned the stem surface, including the worm holes, with q-tips dipped in isopropyl alcohol to remove all the dirt and dust before the fill. I filled the worm hole on the bottom and top surface with clear CA superglue and set it aside to cure. Once the superglue had cured, I sanded the fills with a flat head needle file. To further match the fills with the surface of the stem, I sanded it with 220, 320, 600 and 1000 grit sand paper. I wiped the stem with cotton pad dipped in alcohol to remove the resultant dust. I rubbed some extra virgin olive oil in to the stem and set it aside to be absorbed in to stem. A few minutes later, I polished the stem and also the bone shank extension with micromesh pads, wet sanding with 1500 to 2400 grit pads and dry sanding with 3200 to 12000. I rubbed a little extra virgin olive oil in to both after every three pads. The stem is now nice, smooth and shiny while the extension though smooth and shiny, still had the golden brownish hues of the tobacco oils and tars. I was wondering as to next course of action, Mr. David Goostree, an experienced member from The Tobacco Pipe Restorer group on FB, provided valuable information that the bone is similar to a Meer and absorbs oils from the tobacco and colours just like a meerschaum. Another issue taken care of!!! To finish the restoration, I mounted a cotton cloth buffing wheel to the Dremel (actually it is not the brand machine, but a local machine which is similar). I set the speed at about 40% full power and applied White Diamond compound to the entire pipe. Afterwards, I wiped/ buffed the pipe with a soft cotton cloth to clear it of any leftover compound dust. I then mounted another cotton cloth wheel to the polishing machine, maintaining 40% speed and applied several coats of carnauba wax. I finished the restoration by giving the entire pipe a rigorous hand buffing using a microfiber cloth to raise the shine further. In my excitement mixed with apprehension in using the polishing and waxes for the first time, I completely missed out on taking any pictures. The completed pipe looks lovely, fresh and vibrant. Thank you for having the patience to reach this far while reading the write up. Your comments are of utmost importance to me for improving my skills in restoration process as well as writing about it. Cheers!!!!!

PS: – During this journey of restoring this beauty, I had, on occasions felt low and demoralized as issues kept cropping up like the supposed crack to the stummel, the shank extension not supposedly cleaning up as I had incorrectly anticipated and the 2/3 occasions when the my polishing machine slipped on the surface and caused very minor scratches on the stummel. However, my Guru and mentor, Mr. Steve was always around with his words of wisdom and encouragement to egg me on towards completing this project. Thank you once again, Mr. Steve. I would like to thank all the esteemed members of “The Tobacco Pipe Restorer” group on FB for their interest and valuable inputs, which made this project interesting.

Restoring a Brand I had never heard of before – A Peter Piper 525 Billiard

5 Replies

Blog by Steve Laug

Alex dropped by the other night to drop off a pipe off and to pick up one I was working on for him. He also brought this little billiard with him for me to work on. It is stamped Peter Piper over London Made on the left side of the shank and on the right it is stamped Made in England over the shape number 525. It is a brand I had not heard of and it was an interesting little pipe. It is a reddish coloured billiard. There are some scars and nicks on the surface that are part of the pipe’s story. The finish was worn and there were sticky marks on the shank and sides of the bowl that could have come from a sales label. The rim top had marks on it that looked like it had been tapped out on a hard surface and damaged the briar. The stem had a dental bit made for a pipe smoker with dentures. It had a tall lip on the topside of the stem that could be held behind the top denture. On the underside were two grooves cast in the surface that could be held with the bottom teeth. It gives the pipe a unique look. I took some photos of the pipe at this point to show its condition before I started the cleanup. I took some close up photos of the rim top and the stem to give a clearer picture of the condition of the pipe. The photo of the rim top show the nicks and damage clearly as well as damage to the inner and outer edge of the rim. The stem is very oxidized but there are no tooth marks or chatter on the surface.I wanted to try to figure out where the pipe had come from and who had made it. It was a stamping I was not familiar with. The London Made stamp on the left side and the Made in England stamp on the right side seemed to point to an English pipe making company. I have seen some anomalies in the past where pipes stamped this way were actually made in France. I was curious to see what was behind this pipe.

I turned first to Pipedia.org to see if there was any information on the site about the brand. I check under pipes Made in England and found nothing there. I entered the Peter Piper name in the search box on the site and it took me to the list of French Pipe Makers. Sure enough on the list there was the Peter Piper name. I clicked on that name to see what I could find and it gave me the following information.

The Peter Piper trademark was first applied to a pipe in 1925, and granted on June 1, 1926 to Cadogan France Limited, whose offices were in London. Despite this, the pipe was made at the Marechal Ruchon factory in St. Claude, France. And, despite this, as the pipe was often stamped with London nomenclature. An excellent example of how blurred international borders became where Oppenheimer and Cadogan were involved. For more information see GBD. https://pipedia.org/wiki/Peter_Piper

I followed the link to the “for more information see GBD” statement at the end. I quote that below in part.

Other brands of this time were marketed with even larger independence. The Dr. Plumb’s had been developed by the Parisian sales manager J.B. Rubinovich in 1925 when GBD France needed “a cheap line of pipes” especially for the Canadian market. In fact, the new brand was nicknamed for Mr. Rubinovich’s secretary Leslie W. Plumb, whose most important business was “to doctor figure” the ledgers. Dr. Plumb’s made their way not only in Canada. – The Peter Piper, as well as the Dr. Plumb’s produced in Saint-Claude, is another great example that stampings like “London made” or “London England” are not always totally trustworthy also on older pipes! Not only today numberless brands are made in Saint Claude and stamped with whatever the buyer wants to be stamped… https://pipedia.org/wiki/GBD

I turned to the Pipephil website to see if there was any further information on the brand and found the follow confirmatory information:

… the pipes were stamped “London England” in a straight line, even if they were sometimes crafted in France. http://www.pipephil.eu/logos/en/logo-gbd.html

Now I knew what I was dealing with. Interestingly it was a French Made pipe stamped London Made and Made in England. It was made by GBD France for the Canadian Market to be sold alongside of the Dr. Plumb brand. I love the bit of intrigue that is mentioned above – that the Dr. Plumb brand was named after a secretary, Leslie Plumb whose job was to doctor the ledgers. These pipes made their way to Canada as well as other countries. It is also great proof that the stamping may not always tell the full story.

Armed with this information I started the process of restoration. I topped the bowl with 220 grit sandpaper on a board. I worked the top in a circular motion on the sandpaper to remove the damaged surface and the edges of the bowl. I was so engaged in this restoration that I forgot to take a picture of the rim top after topping. I moved quickly into polishing the rim with the micromesh sanding pads. I wet sanded it with 1500-2400 grit pads and dry sanded it with 3200-4000 grit pads. I wiped it down after each sanding pad. Once I had polished it through the 4000 grit pad I stopped and stained the top with a Maple stain pen to match the rest of the finish. The rim top matched well but still needed to be buffed and polished to blend the stain into the finish of the bowl.I polished the exterior of the bowl and rim with micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. After the polishing I could see the dents and scratches in the bowl sides and bottom. It was time to apply a little steam and see what I could do to raise them. Unlike those who have steam irons that they abscond from their wives to steam their pipes I use a knife and wet cloth. I heat the knife over the flame of a burner on our gas stove until it is hot. I put the wet cloth over the dents and apply the hot knife to the cloth. I repeat the process until the dents have been raised. In this case it worked pretty well. I was able to get the majority of them out of the briar. The photos tell the story. With the externals cleaned I needed to clean the internals. I had forgotten to do the cleaning until now. The pipe looked pretty clean… in fact I kind of wondered if it had been smoked very much. I cleaned the mortise and shank with alcohol, pipe cleaners and cotton swabs. I cleaned the airway in the stem at the same time (you will notice that the stem is quite black at this point. I had already sanded it with 220 grit sandpaper as noted below).I worked Before & After Restoration Balm into the briar with my fingertips to clean, enliven and protect the wood. I let the balm sit for about 20 minutes and buffed it off with a soft cotton cloth. I took photos of the pipe at this point in the process to show what the bowl and rim looked like. I am happy with the stain match on the rim top. I sanded the stem surface with 220 grit sandpaper to remove the oxidation. I worked on the angles of the dental bit and the grooves on the underside of the stem until I had removed oxidation.I polished it with the micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding with 3200-12000 grit pads. I rubbed it down with Obsidian Oil between each pad. I polished it further with Before & After Pipe Polish – both Fine and Extra Fine. I gave it a final coat of Obsidian Oil and set it aside. I polished the bowl and stem with Blue Diamond to polish out the scratches in the briar and rubber. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The original patina on the bowl came alive with the buffing and worked well with the polished black vulcanite stem. The pipe has a rich look. The finished pipe is shown in the photos below. The shape, finish and flow of the pipe and stem work together like other GBD pipes. The dimensions of the pipe are Length: 5 1/2 inches, Height: 1 3/4 inches, Outside diameter of the bowl: 1 1/8 inches, Chamber diameter: 5/8 of an inch. I have one other pipe to finish restoring for this fellow before it will go back to him. I look forward to seeing what he thinks of it.

Converting a Zettervig Freehand into a Churchwarden

Restoring a Dunhill Root Briar EK Square Shank Panel Billiard

2 Replies

Blog by Steve Laug

The next pipe on the work table is a Dunhill Panel Billiard. It is a smooth briar pipe that is very dirty. It has four panels around the bowl and the corners are rounded. The shank is square as well and ends with a square tapered stem. The briar is worn and tired with oils in the briar. The rim top had a build of tars and lave that flowed over it from a thick cake in the bowl. The shank is stamped on the left side EK followed by Dunhill over Root Briar. On the right side it is stamped Made in England with an underlined superscript ⁰ followed by a 4 circled followed by an R. The stem has the standard white spot on the top side. It was oxidized and had some calcification build up on the first inch of the stem that appeared to have come from a rubber pipe Softee bit. The stamping is easily interpreted. The left side EK is the shape stamp for a panel billiard. The ROOT BRIAR stamping is the line of Dunhill pipes. The right side stamp superscript O tells me that the pipe is dated to 1960. The circled 4 is the size of the pipe (group four) and the R is the stamping for a Root Briar. Jeff took photos of the pipe before he started his cleanup work. Jeff took photos of the top, sides and the bottom of the bowl to show the condition of the briar. The topside showed a thick lava build up flowing out of a thick cake in the bowl. It was hard to know if there was damage on the outer or inner edges of the rim. The sides of the bowl show dents and wear but also some stunning birdseye and cross grain. Jeff took photos of the stamping on the pipe shank. It is faint but readable. It is as I wrote about above.Jeff took a photo of the stem to show the fit against the shank and the white spot. He also took photos of the top and underside of the stem showing the tooth chatter and marks as well as the calcification on the surface of the stem.I wanted to certify the date for myself so I had a look at the PipePhil site and looked the dating and stamping information (http://www.pipephil.eu/logos/en/dunhill/cledat-en1a.html). Using the charts there I was able to confirm that pipe was made in 1960.

I also looked on the Pipedia site and read as much information as I could find regarding the Root Briar line (https://pipedia.org/wiki/Dunhill#Root_Briar). Here is what it said: The line was… Introduced in 1931 and highly prized because the grain is more pronounced in this finish. The Root Briar finish required a perfectly clean bowl with excellent graining. Therefore, it is the most expensive of the Dunhill pipes. Corsican briar was most often used for the Root finish, since it was generally more finely grained. This is a rare finish, due to the scarcity of briar suitable to achieve it. These pipes are normally only available at Company stores, or Principle Pipe Dealers…

Jeff reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils, lava and tars on the rim and the grime on the finish of the bowl. He rinsed it under running water. He dried it off with a soft cloth. The rim was thoroughly cleaned and without the grime the finish had some rim darkening that hid the grain. The vulcanite stem would need to be worked on but I really like the profile it cast. I took photos of the pipe to show its condition before I started my work on it. I took close up photos of the bowl and rim top as well as the stem. You can see the condition of the rim top and bowl in the first photo. Jeff was able to remove all of the tar and oils but you can now see the damage and darkening around the inner edge. The vulcanite stem had tooth chatter and some light tooth marks on the top and underside of the stem both on the surface of the button and just ahead it. There was one deeper tooth mark on the topside near the button.I started my refurbing work by addressing the darkening on the rim top and inner edge. I first sanded the inner edge with a folded piece of 220 grit sandpaper. I then lightly sanded the rim top with a worn piece of 220 grit sandpaper. I find that using a bit more tired piece of sandpaper works wonders on the dark edge without scratching the rim surface like a new piece. I followed that by wet sanding it with 1500-2400 grit micromesh. I sanded the rest of the pipe with the micromesh at the same time. I dry sanded it with 3200-12000 grit sanding pads. I wiped down the bowl after each pad with a damp cloth. The grain on the rim top began to shine through and the finish was in good condition under the darkened grain. I rubbed down the smooth briar with Before & After Restoration Balm. I worked it into the smooth surface of the briar on the rim, sides and the bottom of the bowl with my fingertips. I wanted to make sure that the balm got deep into the briar to do its work. The balm works to clean, enliven and protect the briar. I let it sit for a little while and then buffed with a cotton cloth to raise the shine. The following photos show the bowl at this point in the restoration process. The rim looks much better than when I started but still needs to be polished and buffed to raise a shine on it. I sanded out the tooth chatter and tooth marks on the stem surfaces. I sanded the rest of the stem with the sandpaper to remove the oxidation on the stem surface.I polished the vulcanite stem with micromesh sanding pads – wet sanding with 1500-2400 grit sanding pads and dry sanding it with 3200-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it further with Before & After Pipe Polish – both Fine and Extra Fine polishes and gave it a final coat of Obsidian Oil and set it aside to dry. I the polished stem and the bowl with Blue Diamond to polish out the remaining small scratches and raise the shine. I gave the bowl and the stem multiple coats of carnauba wax then buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. I left the some of the dents in place as I did not want to sand and ruin the patina. I think they are marks of the journey the pipe has taken. This turned out to be a beautiful pipe in terms of shape and finish. This is a nice looking Dunhill Panel Billiard pipe. The finished pipe is shown in the photos below. The dimensions are Length: 5 3/4 inches, Height: 1 3/4 inches, Outside diameter of the bowl: 1 1/4 inches, Chamber diameter: ¾ of an inch. Thanks for walking through the restoration with me as I worked this beautiful Dunhill Root Briar Panel. Thanks for looking.

114. A Visual History of Peterson’s Shape 999

Cleaning up a Cadogan Era Comoy’s Silver Shadow 225

Reclaiming a Yello-Bole “Imperial Carburator” Vest Pipe

2 Replies

Blog by Paresh Despande

Having worked on the four Free Hand pipes that I had purchased on eBay, it was time again to work on one of my grandfather’s pipe from my inheritance. I chose to work on the second “Imperial Yello-Bole Carburetor” from his collection. The first had a cracked shank and was restored by my Guru and mentor, Mr. Steve of rebornpipes, here is the link for the write up (https://rebornpipes.com/2018/04/15/pareshs-grandfathers-pipe-2-a-yello-bole-carburetor-4522-billiard/).

This particular pipe was in a battered condition with significant damage to the inner and outer edges of the rim, a large number of chips, dents and dings to the bowl and shank, two deep gouges to the bowl and a heavily oxidized stem. I was not very sure if at all I should attempt at its restoration as I knew that to mask the repairs/ fills to the gouges and chips on the bowl and the shank, I would need to stain it with a darker stain followed by a delicate polish to make the grains pop and here I was, with neither materials nor experience to carry out staining and subsequent polishing. However, Mr. Steve encouraged me to go ahead and restore it nevertheless and keep the natural finish of the pipe and the scars of the repairs as a testimony of the pipe’s journey till date!!!! Well, it always pays to follow the advice of your mentor and I embarked upon this journey to give a fresh lease of life to this old and battered war-horse!!!

The pipe is stamped on the left side of the shank as “Imperial” in fancy cursive hand over “YELLO-BOLE” in block letters while the right side of the shank bears the stamp of “MADE IN FRANCE” starting from the shank end towards the bowl and followed by the model(?) number “648” or is it “64 B”? I have this doubt since I could find a match to this shape and size during my research as per the latter stamp, but the stamp appears as former to my eyes!!!! The center bottom of the pipe has a single hole, lined by an aluminum cone, open at both ends, which protrudes into the chamber. This is followed by “carburetor” in fancy cursive small letters. The stem is devoid of any stampings or logo. Before commencing the restoration, I decided to refresh my memory about Yello-Bole pipe brand and in particular, the Carburetor model, by visiting the blog written by Mr. Steve while restoring my first Yello-Bole. The first thing that struck me as odd was the difference in stampings seen on the pipe which is on my work table!!! The pipe currently on my work table is sans the stamp of KBB in clover leaf, U.S. patent number details, Cured with real honey, stem logo of a yellow circular ring and has shape number in three digits as against four on the one restored by Mr. Steve. However, the biggest and most significant difference which has me flummoxed was the stamping “MADE IN FRANCE”!!!!!!! No amount of research and surfing the internet provided me any clue as regards the origin and dating of this piece of briar.

INITIAL VISUAL INSPECTION
The first and foremost significant visual damage is seen to the rim top, inner and outer edges. It appears that the rim has been repeatedly banged against a hard surface to remove residual dottle over a prolonged period of time!!!! The damage to the rim top is in the form of dings and scratches while significant chipping and cinching is seen on the outer edge. The inner edge of the rim is out of round, apparently caused by use of a knife to remove the carbon cake. The overflow of lava from the rim top appears to be removed by scrapping the surface with a knife and in the process causing all the scratches and dings to the surface. There is a thin layer of cake on the bottom half of the chamber and appears to be a victim of over reamed chamber. The carburetor hole at the bottom of the chamber is clogged and will require to be cleaned. The condition of the inner walls of the chamber will be ascertained only after the chamber has been stripped completely of the existing cake layer.The second most significantly damaged part of the pipe is the stummel. It is covered in oils, dirt and grime of all these years of smoking and subsequent uncared for storage. The stummel surface is sticky to the touch, giving the stummel a dull, lifeless and lackluster appearance. It is peppered with a large number of chips, dents and dings. There are two significant gouges on the stummel; one on the left hand side towards the bottom and the second one is one the right hand side about an inch below the rim top. Overall, the stummel has sustained massive damage over the years due to both, rough usage and careless storage. However through all this dirt, tar, oil, grime and damage, lovely densely packed straight grains can be seen on the sides and shank. It will be a challenge to address these issues and make the grains to reveal themselves in all glory. The shank too is peppered with numerous minor dents and chips on the bottom surface as well as on the right side of the shank. The mortise is clogged and the air flow is constricted and the draw is laborious. This will need to be addressed by thorough cleaning of the same. The saddle stem is heavily oxidized with bite marks on both upper and lower surface of the stem. The lip too shows bite marks and will need to be redefined. The aluminum stinger is firmly attached inside the tenon and could not be removed. It is covered in oils, tars and grime from all the years of smoking and it appears that it has hardened, fixing the stinger inside the tenon.THE PROCESS
I started the process of restoration by reaming the chamber with my fabricated knife as the protruding aluminum cone of the carburetor prevented use of the Kleen Reem pipe reamer. Once the cake was reamed back to the bare briar, I used a 150 grit sand paper followed by 220 grit sand paper to remove all the traces of remaining cake and also to smooth the inner walls of the chamber surface. It was a big relief to note that there was no issue of heat fissures or cracks seen on the surface.To address the numerous dents, dings and scratches on the rim’s top surface and also to remove traces of lava overflow, I topped the rim surface on a 220 grit sand paper. Since the damage to the rim top was significant, I had applied more pressure than usual. Though it is recommended to have a wooden board with the 220 grit sand paper firmly fixed over it, I just keep the sand paper on a flat table top, holding it firmly with my left hand and rotating the stummel rim top over it with my right hand. I have come to realize that this set up gives me lot more freedom of movement, better control and convenience of storage.Staying with the rim, the next issue that I addressed was the rim edges, both inner and outer. With a folded piece of 180 grit sand paper pinched between my thumb and fore finger, I created a bevel on the inner edge. This addressed the issue of uneven and out of round inner edge. For addressing the outer edge, I had two options; first was to top the rim surface till the entire damaged outer rim surface was sanded out, maintaining the straight rim edge profile of the stummel. The disadvantage of this would be a significant loss of briar estate!!! The second (and easier too!!!) option was to create a bevel on the outer edge, sacrificing the original profile of the stummel. However, I envisaged that the bevel to the outer edge would add a new depth and dimension to the profile of the pipe while saving loss of briar. That decided, I created a bevel on the outer edge. Both the inner and outer edges now look much better and add a new dimension to the otherwise plain-Jane billiard shape of the bowl. I cleaned the stummel with Murphy’s oil soap and hard bristled toothbrush and rinsed the stummel under running tap water. This cleaning helps in bringing to the fore any other damage which could be hidden under all the dirt and grime. I dried the bowl with a paper towel and soft cotton cloth. With a thin, sharp and pointed knife, I cleaned out all the fills and gouges. I scrubbed the stummel surface clean with isopropyl alcohol to have a clean surface for a fresh fill. I decided to move ahead with only CA superglue for filling the chips and gouges. I spot filled these chips and gouges with superglue and set it aside for curing. Turning my attention to the stem, I flamed the surface with a Bic lighter to raise the tooth chatter and deeper bite marks to the surface as much as is possible. I followed it up with sanding the stem surface with a 220 grit sand paper to match the raised bite marks with the stem surface and also remove the oxidation before the fill. The deeper bite marks were filled with CA superglue and set aside to cure. After the fills on the stummel had completely cured, I sanded these with a flat head needle file to match them with the stummel surface. This was followed by sanding the fills and the stummel surface to achieve a match as well as remove the minor scratches and cinches on the surface. I frequently wiped the sanded surface with a moist cloth to remove the briar dust and also to check the progress of my work. Once I was satisfied with the match, I followed it up by micromesh polishing pads, wet sanding with 1500 to 2400 grit pads. Again, I wiped the bowl with a moist cotton cloth after each pad. I used the 3200 to 12000 grit pads to dry sand the stummel to a nice shine. At this stage of restoration, the entire bowl, rim top surface and shank is now looking fresh and clean with beautiful densely packed straight grains popping out in all their glory!!!! Even though the fills are prominently visible, in my view, they lend a battle scarred warrior like character to the pipe. While I worked the stummel, the fillings in the stem had cured. I sanded the fills with a flat head needle file. To further match the fills with the surface of the stem, I sanded it with 220, 400 and 800 grit sand paper. I wiped the stem with cotton pad dipped in alcohol to remove the resultant dust. I rubbed some extra virgin olive oil in to the stem and set it aside to be absorbed in to stem. I polished the stem with micromesh pads, wet sanding with 1500 to 2400 grit pads and dry sanding with 3200 to 12000. I rub a little extra virgin olive oil in to the stem after every three pads. I finish the polishing of the stem by rubbing a small quantity of Paragon wax and giving it a final polish with a soft cotton cloth. The stem is now nice, smooth and shiny. Now with the external restoration and cleaning of both the stummel and the stem completed, I proceeded to cleaning the internals of the stem and the shank. As I had observed during my initial visual inspection, the stinger was very firmly attached inside the tenon. To clean the stem air way, I had to separate the stinger from the tenon. I was certain that the stinger was a push-fit type and much easy to deal with. I carefully heated the stinger with the flame of a Bic lighter and wrapping a cloth on the stinger, with careful anti-clock wise rotations, dislodged the stinger from the tenon. I cleaned the internals of the shank with cue-tips, regular and bristled pipe cleaners dipped in alcohol. The mortise was cleaned using a shank brush. With a fabricated dental spatula, I scrapped the walls of the mortise and further cleaned with pipe cleaners till they came out white. Similarly, I cleaned the air way in the stem with pipe cleaners and alcohol. I cleaned the stinger of all the accumulated oils and tars with paper towels after soaking the stinger in isopropyl alcohol and reattached it in the tenon. The internals are now clean and the draw is full, easy and open. I was really not surprised at how dirty were the internals of the shank and stem as can be seen from the condition of the pipe cleaners in these pictures. To finish the restoration, I rub a small quantity of “Before and After Restoration Balm” in to briar and let it rest for a few minutes. The balm almost immediately works its magic and the briar now has a nice vibrant appearance. I further buff it with a horse hair shoe brush. Using a cotton cloth and brute muscle power, I gave it a final polish. I re-attach the stem with the stummel. The completed pipe looks lovely, fresh and vibrant; the photographs speak for themselves. Thank you for having the patience to reach this far while reading the write up. Your comments are of utmost importance to me for improving my skills in restoration process as well as writing about it. Cheers!!!!!

Recommissioning a Comoy’s Moorgate 102 of Italy

1 Reply

Blog by Dal Stanton

I saw this attractive Comoy’s Moorgate on the eBay auction block last year and fortunately provided enough of a bid to bring it home to Bulgaria. What attracted me to this Comoy’s was the interesting finish which is a darkened, orange hue with nice feathered grain. This Comoy’s Moorgate also got Jim’s attention after he saw it posted on my website in the For ‘Pipe Dreamers’ Only! collection I list online for pipe men and women to commission. I enjoyed communicating with Jim via email very much. Jim not only commissioned the Comoy’s, but he also commissioned a very interesting, older Stanwell Henley Special which I acquired along with 2 brother Stanwell Henleys – 3 pipes I’ve been looking forward to restoring and learning more about. Along with these 2 pipes that Jim commissioned, were his encouraging words of appreciation for the work we’re doing with the Daughters of Bulgaria – women and girls who have been trafficked and sexually exploited. Jim was glad that the pipes he was commissioning benefited these efforts. Thanks, Jim! Here are a few pictures of the pipes – the Comoy’s and the Stanwell Henley Special – Jim’s is the Saddle Stem Billiard in the middle. When Jim commissioned these pipes, I’m grateful that he also agreed to be patient as the pipes gradually made it to the top of the queue. I take some additional pictures to take a closer look at the Comoy’s Moorgate on my worktable here in Sofia, Bulgaria, on the 10^th floor of a formerly Communist block apartment building. The nomenclature identifies this Comoy’s as a post-Cadogan era pipe which dates it no older than the early 1980’s when the Cadogan merger took place. On the left side of the shank is ‘COMOY’S’ [over] ‘MOORGATE’. The right side of the shank is stamped with the shape number, ‘102’. The upper side of the stem has the well-known ‘C’ Comoy’s stamp and the underside is stamped, ‘ITALY’. All the stampings point to a post-merger Comoy’s pipe. The COM being Italy and not ‘Made in London England’ confirms this as Cadogan farmed out the manufacturing. Interesting also is the shape number, ‘102’. Pipedia provides a Comoy’s Shape Number Chart that identifies the 102 as being an army mounted, large, straight Pot which does not correspond to the Half Bent Billiard on my table. The chart most likely pointing to earlier shape numbers.Pipephil.eu provides a Comoy’s Moorgate that matches up with what I’m seeing before me – nomenclature and stampings. It references a Comoy’s second brand with the name ‘Moorgate’. I look up the reference and it is a different line altogether – nomenclature and stem stamps and COM as ‘Made in England’.Looking at the condition of the Comoy’s Moorgate on my worktable, it is generally in good condition. I take a few more pictures to look at some trouble areas. The chamber has moderate cake build up and some significant lava flow caked on the rim. The bowl surface has some dents which I’ll try to lift with the hot iron method to preserve the finish. The stem has moderate oxidation and tooth chatter – no huge problems detected there. To begin, I run a pipe cleaner wetted with alcohol through the draft way and then put the stem in a bath of Before & After Deoxidizer along with several other pipes in the queue. After several hours soaking, I fish out the Comoy’s stem and allow the Deoxidizer fluid to drain off. I then take a cotton cloth wetted with alcohol and wipe off the raised oxidation. I continue wiping off oxidation and conditioning the stem by wetting the cotton pad with light paraffin oil. The Deoxidizer seems to have done a good job. Next, I address the chamber cleaning by reaming it with the Pipnet Reaming Kit. To help with the cleanup, I put down some paper towel to catch the dislodged carbon. Beginning with the smallest of four blade heads, I ream the chamber. I only use 2 of the 4 blades available. I follow this by using the Savinelli Fitsall Pipe Tool to fine tune the reaming. I also use the Fitsall Tool to scrape gently an internal rim bevel that emerges from underneath the carbon cake. I also use my thumbnail to scratch the carbon off the rim. Following this, I wrap a piece of 240 grit paper around a Sharpie Pen and sand the chamber. Finally, to remove the carbon dust, I wipe the chamber with a cotton pad wetted with isopropyl 95%. With the chamber cleaned, I inspect the chamber walls and I find no issues with heat fissures or cracking. Turning now to the external briar surface, I use undiluted Murphy’s Soap on a cotton pad and clean. I take my time on the rim to remove the lava. After cleaning the surface, I use cool tap water to rinse the bowl.Turning now to the internals of the bowl, I use cotton buds and pipe cleaners with alcohol to clean. I also use a dental spatula to scrape the mortise walls more quickly removing the built-up tars and oils. In time the buds and pipe cleaners start coming out cleaner. Good for now. I move on!To achieve a deeper cleaning and refreshing of the internals, I use a kosher salt and alcohol soak. Using a cotton ball to create a wick, I stretch and twist it and then insert it through the mortise and into the airway. I then fill the bowl with kosher salt and place it in an egg carton to provide stability. With a large eye dropper, I then fill the bowl with isopropyl 95% until it surfaces over the salt. I top the alcohol in a few minutes after it’s absorbed into the salt. I put the stummel aside for several hours to soak. After some time, the salt and the wick were soiled. I tossed the expended salt, wipe the bowl with paper towel, and blow through the mortise to remove salt crystals. To make sure all was clean, I use a cotton bud and pipe cleaner dipped in isopropyl 95% and they are clean.Putting the cleaned bowl aside, I take the flat needle file and work on the button. I file the button lips, upper and lower to redefine them. To erase the scratches of the file, I follow by sanding the bit area, upper and lower with 240 grade sanding paper. I also sand the entire stem to remove further residual oxidation. I’m careful to avoid the stem stampings while sanding. To remove the scratches left by the 240 grade paper, I wet sand using 600 grade paper followed by applying 0000 steel wool buffing to the entire stem.In order to further enrich the vulcanite, I use Before & After Fine and Extra Fine Polish in that order. I put some Fine polish on my fingers and work the polish in. After some minutes, I wipe it off. I follow with the same process with the Extra Fine Polish, giving it some minutes and wiping it off and buffing up the stem. The stem is cleaning up very nicely.Turning again to the stummel, there are 2 significant dents that I want to see if I can minimize using the heating method with an iron. I take pictures of the two places I have in mind. I heat the iron and dampen a cotton handkerchief with water. I place the cloth over the dent and press the hot iron against the cloth over the dent in the briar. The heat and moisture are supposed to expand the dent and in this case it does. Interestingly, taking a picture of the two dents afterwards, what emerged is a roughness caused by the heat. Hmmm, not sure why that happened. The pictures show what I see before and after heating. To remove the roughness caused by the heating and to remove the normal wear nicks, I wet sand the stummel using micromesh pads 1500 to 2400. I then dry sand with pads 3200 to 4000 and 6000 to 12000. The grain on this Comoy’s Moorgate is unique as it emerges through the micromesh process. It looks great! To enrich the natural grain of the bowl, I apply Before & After Restoration Balm. I apply some Balm on my fingers and work it into the briar surface. The Balm starts with a thinner oil-like viscosity then gradually thickens to a waxy consistency. After I apply the Balm thoroughly, I let the bowl stand for several minutes while the Balm absorbs. I then wipe off the Balm using a microfiber cloth and gradually, as the Balm is removed, I transition to buffing with the cloth. I take a picture while the Balm is doing its thing and after. I’m liking it a lot!Returning to the stem, I now continue with the micromesh sanding phase. I begin by wet sanding using pads 1500 to 2400, then dry sanding using pads 3200 to 4000 and 6000 to 12000. Between each set of 3 micromesh pads, I apply Obsidian Oil to continue revitalizing the vulcanite. The rubber has that glossy pop! I put the stem aside to dry. Next, I want to refresh the stem stamping, ‘ITALY’. To do this I place a drop of white acrylic paint over the lettering. I then use a cotton pad to blotter the excess paint, thinning it so that it dries rapidly. With the flat edge of a toothpick, I then gently scrape the excess paint off the stem. The pictures show the progress. I now reunite the stem and the bowl and mount a cotton cloth buffing wheel to the Dremel. I set the speed at about 40% full power and apply Blue Diamond compound to the entire pipe. Afterwards, I wipe/buff the pipe with a felt cloth to clear it of leftover compound dust. While I was buffing with the felt cloth, I note that the stem fitting is a little loose for my liking. This sometimes happens after cleaning the pipe well and scraping the mortise. To remedy this, I fit a drill bit just larger than the airway diameter and heat the tenon with a Bic lighter. As the vulcanite tenon heats, it becomes supple allowing me to insert the bit into the airway and it expands the tenon slightly. I test the fit and it works perfectly, and I am satisfied. After rejoining stem and stummel, I then mount another cotton cloth wheel to the Dremel, maintaining 40% speed and apply several coats of carnauba wax. I finish the restoration by giving the entire pipe a rigorous hand buffing using a microfiber cloth to raise the shine further.I’m pleased with the results of this Comoy’s Moorgate. The briar is spectacular with its diversion of colors and swirls of grain. Patches of orange settle in the grain knots and from there the colors are an eye catching kaleidoscopes. It is a unique piece of briar and the half-bent Billiard nicely rests in the palm. Jim commissioned this Comoy’s from the For ‘Pipe Dreamers’ Only! collection and he will have the first opportunity to acquire it from The Pipe Steward Store. This pipe benefits the Daughters of Bulgaria – women and girls who have been trafficked and sexually exploited. Thanks for joining me!