Restoring a Golden Parker Danish Style 141 Bent Acorn


Blog by Steve Laug

The next pipe on the work table we purchased in 2018 from a fellow Scottsdale, Arizona, USA. It is a mixed grain in a Danish looking shape. The bowl has a rich reddish brown colour combination that highlights grain. The pipe was dirty but appeared to be in decent condition under the grime. There was grime and oils ground into the surface of the briar. This pipe is stamped on the sides of the shank. On the left it reads Golden [over] Parker. To the left of that is the shape number near the bowl that reads 141. On the right it Made in London [over] England. There is a tarnished Sterling Silver band on the shank that appears to be a repair band. The fancy saddle stem has no distinguishing marks or logos. There was a thick cake in the bowl and a heavy overflow of lava on the crowned rim top. It is hard to know the condition of the top or edges underneath the lava. We would know more once it was cleaned up. The stem was oxidized, calcified and had tooth marks and chatter on the stem surface. It was definitely someone’s favourite pipe judging by the condition it arrived at Jeff’s house. He took photos of the pipe before he started his cleanup. He took a photo of the rim top to show condition of the bowl. It is hard to tell for sure but the inner edge of the bowl looks good the lava coat. The top and outer edge also look okay. It is a very dirty pipe. He also captured the condition of the stem. It is oxidized, calcified and has tooth marks and chatter on the top and underside of the stem near the button. He took photos of the sides and heel of the bowl to show the beautiful grain around the bowl and the condition of the pipe. There was a spot on the lower left side of the bowl where the pipe appeared to have been dropped and there was some “road rash”.    He took a photo of the stamping on the sides of the shank. It is clear and readable as noted above.  The repair band was well done and did not cover the stamping on the left side and went right along side of the M on Made in in England on the right side.  The tarnish silver repair band is stamped Sterling. I turned first to Pipephil’s site to look at the Parker write up there and see if I could learn anything about the line (http://www.pipephil.eu/logos/en/logo-parker.html). There was a Parker Golden pipe listed and the stamping matched the one that I am working on but there was no further information on line.I looked up the Parker brand on Pipedia to see if I could find the Parker Golden (https://pipedia.org/wiki/Parker). There was nothing that tied directly to the line I am working on. There is a decent history of the brand there that is a good read.

It was time to work on the pipe. As usual Jeff had done a thorough cleanup on the pipe. He reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils and tars on the rim and the grime on the finish of the bowl. He rinsed it under running water. One of the benefits of this scrub is that it also tends to lift some of the scratches and nicks in the surface of the briar. He dried it off with a soft cloth. He cleaned the internals and externals of the stem with alcohol, pipe cleaners and cotton swabs. He soaked the stem in Before & After Deoxidizer and rinsed it off with warm water and cleaned out the airway in the stem with alcohol. Other than the damaged rim top the pipe looked good. I took a photo of the rim top and stem to show the condition. The rim top and edges looked very good. The vulcanite stem had tooth chatter and marks on both sides ahead of the button and on the button edges.  The stamping on the sides of the shank is clear and readable as noted above.    I removed the stem from the shank and took a photo of the pipe to give a sense of the whole. It is a nice Bent Acorn that should clean up very well. I started my work on the pipe by cleaning up the rim top and edges. I used a folded piece of 220 grit sandpaper to remove the damaged areas and scratches in the bowl. It looked much better than when I started.  I filled in the damaged areas on the left side of the owl with clear super glue. Once the glue cured and hardened I sanded them smooth with a folded piece of 220 grit sandpaper. Once finished they were smooth.   I polished the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads. I wiped the bowl down between pads with a damp cloth.   I rubbed the bowl and shank down with Before & After Restoration Balm. I worked it into the surface of the bowl sides and shank with my fingertips to clean, enliven and protect the briar. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The Balm did its magic and the grain stood out.    I set the bowl aside and turned my attention to the stem. I “painted” the surface of the stem with the flame of a lighter to lift the tooth marks and chatter. I was able to life many of them. I filled in the remaining marks with clear super glue. Once the repairs cured I sanded them smooth with 220 grit sandpaper to blend them into the surface. I started polishing them with 400 grit wet dry sandpaper. I polished the vulcanite stem with micromesh sanding pads – 1500-12000 grit pads. I wiped it down with Obsidian Oil after each sanding pad. I used Before & After Pipe Polish – both Fine and Extra Fine to further the stem. The photo below shows the polished stem. This nicely grained Golden Parker 141 Danish Looking Bent Acorn with a Sterling Silver repair band and a fancy vulcanite saddle stem is a great looking pipe now that it has been restored. The briar around the bowl is clean and really came alive. The rich brown stains gave the grain a sense of depth with the polishing and waxing. The grain really popped. I put the vulcanite stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Golden Parker Bent Acorn is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¼ inch, Chamber diameter: ¾ of an inch. The weight of the pipe is 40grams/1.41oz. This will be going on the rebornpipes store under the British Pipemakers section soon. Thanks for reading this blog and my reflections on the pipe while I worked on it. There are many more to come!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.