Tag Archives: Ben Wade Majestic Pipes

What a Great Looking Ben Wade Majestic Designer Series B Danish Freehand

by Steve Laug

The next pipe on the work table is a pipe that came to us from a seller in Santa Cruz, California, USA on 05/28/2024. It is stamped on the left side of the shank and read Majestic [over] Designer Series B. On the right side it read Ben Wade [over] Hand Made In Denmark. The finish on the pipe was a smooth Ben Wade style finish with brown stains highlighting the grain around the sides and shank. The bottom of the bowl was flat from the heel to the shank end so that it acts as a sitter. The rim top was also smooth and crowned and was dirty with grime and also lava overflowing from the thick cake in the bowl. The fancy saddle stem was brown/gold variegated acrylic and had light tooth marks and chatter on both sides ahead of the button. It has a gold Ben Wade crown with a BW underneath stamped on the top of the saddle. It was a pretty stem but was dull and dirty. Jeff took some photos of the pipe to show the general condition of the pipe before he started his clean up. It should clean up very well. Jeff took some close-up photos of the rim top and bowl to show the overall condition. There is dust and lava on the crowned top. The edges have a lava overflow but underneath it appears to be in good condition. The acrylic saddle stem is dirty and has some light tooth chatter and some tooth marks. Jeff took some photos of the sides and heel of the bowl to show the condition of the finish on the pipe. The photos show the beautiful grain around the bowl. Under the dust and grime, it was a nice looking bowl. I think it will be a beautiful Freehand pipe once it is restored. He took a photo of the stamping on the sides of the shank. The stamping is clear and readable as noted above. There was also a Crown with a BW stamped below it on the topside of the saddle portion of the stem. I have worked on quite a few Ben Wade pipes over the years and one Majestic Designer Series that had the stamping on the shank side XXX’d out but was still very readable without looking to hard (https://rebornpipes.com/2016/02/21/restoring-an-interesting-older-xxxxd-out-sitter/).

I knew from the previous work that I should take time and check out my common sites for information. I turned first to Pipephil’s site in the Ben Wade Section and found an entry there on the brand (http://www.pipephil.eu/logos/en/logo-benwade.html#majestic). There was a section in the list stamped Danish Made Majestic. I did a screen capture of the section and have included it below.From there I turned to the section the reference above directed me to under the heading Majestic with a link to the Ben Wade stamp. I have also included that link and the screen captures of the site below (http://www.pipephil.eu/logos/en/logo-m1.html#majestic).From there I turned to Pipedia to see what I could find (https://pipedia.org/wiki/Ben_Wade). I found some photos of a pipe that is stamped the same as the one that I have. I have included them below showing the shape of the pipe and the stamping on the pipe. Now that I was reminded about the Ben Wade Majestic Line it was time to work on the pipe on my end. When I received it, Jeff had once again done an amazing job cleaning the pipe. He reamed it with a PipNet pipe reamer and got rid of the cake. He cleaned up the reaming with a Savinelli Fitsall Pipe Knife so that we could see the walls of the bowl and assess for damage. He cleaned the internals of the shank and stem with alcohol, pipe cleaners, cotton swabs, shank brushes and alcohol. He scrubbed the exterior with undiluted Murphy’s Oil Soap and a tooth brush. He rinsed the pipe under warm water. He dried it off with a cloth and then let it air dry. The stem was scrubbed with Soft Scrub and soaked in Before & After Deoxidizer. It came out looking very good. The finish on the bowl and the rim top cleaned up nicely. I took pictures of the pipe to show how it looked when I unpacked it. I took a close up photo of the plateau rim top to show how clean it was. The inner edge of the rim and the ridges and valleys of the plateau looked good. The stem looked good just some light tooth chatter and tooth marks ahead of the button. One of the things I appreciate about Jeff’s cleanup is that he works to protect and preserve the nomenclature on the shank of the pipes that he works on. He was able to preserve and maintain its condition in the process. I took some photos to show the clarity of the stamping. I have noticed that many restorers are not careful to protect the stamping in their cleaning process and often by the end of the restoration the nomenclature is almost destroyed. Be careful in your work to preserve this critical part of restoration! I took the stem off and took a photo of the pipe. The pipe was in decent condition so I started with the bowl. I sanded the bowl sides with 320-3500 grit sanding pads. I wiped it down after each sanding pad with a damp cloth to remove the debris left behind by the sanding process. I polished the smooth portions of the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping down the briar after each sanding pad with a damp cloth. The briar began to shine. I worked some Before & After Restoration Balm into the smooth briar with my fingertips. It enlivens, enriches and protects the briar while giving it a deep glow. I appreciate Mark Hoover’s work in developing this product. I buffed the pipe with a micro fiber cloth to raise the shine and took photos of it at this point it the process. It is a beautiful looking pipe. I set the bowl aside and turned my attention to the stem. It was interesting to note that the stem had a white Delrin tenon. I sanded the stem with the 2 inch square 320-3500 grit sanding pads. I wiped down the stem after each sanding pad with Obsidian Oil. The stem looked very good.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I buffed the stem with a soft cloth to raise the shine. I wiped the stem down with Obsidian Oil to preserve and protect the stem surface. I am on the homestretch with this Ben Wade Majestic Design Series B Made in Denmark Freehand. As always, I am excited to finish a pipe that I am working on. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I used a gentle touch on the sandblast portion of the bowl. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad and hand buffed it to raise the shine. It is fun to see what the polished bowl looks like along with the polished bronze acrylic stem. This Ben Made Majestic Design Series Freehand is a nice looking pipe. It is quite comfortable in hand and should be so when smoking. It is quite light and well balanced. Have a look at it with the photos below. The dimensions are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ¾ inches, Chamber diameter: 1 inch. The weight of the pipe is 1.52 ounces/43 grams. It is another beautiful pipe and one that will be on the rebornpipes store soon. You can find it in the section of Pipes by Danish Pipe Makers. If you are interested in adding it to your collection let me know.

As always, I encourage your questions and comments as you read the blog. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipe men and women who hold our pipes in trust until they pass on into the trust of those who follow us.

Restoring an Interesting Older XXXX’d out Sitter

5 Replies

Blog by Steve Laug

When my brother Jeff sent me the photos of this pipe I could see what had attracted him to purchasing it. The unique sitter shape with the angled bottom, the interesting grain patterns and the clean though oxidized stem all pointed to a pipe that would clean up very well. The stamping on the left side of the shank was XXXX’d out so he could not read it to see who had made the pipe. There was something about it however, that niggled at my memory and the shape had a quintessential British made pipe look. When it arrived I examined it under a bright light and was able to make out the stamping under the XXX’s. It read MAJESTIC over Danish Crown. From research on the web I found that the brand was made by Ben Wade in England. In person the pipe was quite nice. There were scratches and nicks in the bowl that would need some work. On the left side toward the bottom of the bowl were two marks joined by a line. At first glance it looked like a crack but it was not. There were two flaws in the briar and a long horizontal scratch in the surface of the briar. Even if it had been a crack the two flaws stopped it from spreading so it was not a problem.

There was beautiful grain on the sides and bottom of the bowl. The dirty rim promised some interesting grain underneath the tars and lava build up. The outer edge of the rim had damage on the front and the rear. It had been tapped out on something solid and had rounded and damaged the edge. The inner edge looked good though the crumbling cake would need to be reamed to know for sure.

I reamed the bowl with the PipNet reamer and completely removed the cake. I wanted to clean up the inner edge of the rim and check the bowl walls for cracks or damage. (In the top view photo you can see the rounding on the front and back outer edges of the rim.)

I cleaned out the airways from button to bowl with pipe cleaners, cotton swabs and alcohol. I used a dental pick to clean out the slot.

I scrubbed the exterior of the bowl with acetone on cotton pads to remove the grime and the damaged finish.

I scrubbed the rim and then used the topping board to remove the damaged top of the rim. A light topping took the surface down and sharpened the edges on the front and back side of the bowl.

I used the dental pick to clean up the line and the two end points that marked the bowl on the left side. I used clear super glue to fill in the flaws and the groove in the line. I sanded the repairs to the bowl until the surface was smooth. I sanded it and the rim with micromesh sanding pads 1500-6000 grit. I used a black marker and a dark brown stain pen to prepare the bowl for staining. I decided to use a Cherry Stain and Danish Oil on the briar on this one. It would highlight the grain and make it shine.

I laid the pipe aside to dry over night. In the morning I buffed it with some Blue Diamond and then gave it a coat of carnauba wax. I buffed it with a flannel buffing pad and then took the next photos.

The stem still needed attention. I sanded it with 220 grit sandpaper to remove the nicks and deep oxidation in the vulcanite. I followed that by wet sanding it with 1500-2400 grit micromesh sanding pads and rubbing it down with Obsidian Oil. I dry sanded with 3200-4000 grit pads and repeated the oil. I finished by dry sanding it with 6000-12000 grit pads and gave it a final coat of oil. I set it aside to let the oil soak into the vulcanite.

I buffed the pipe with Blue Diamond and then gave it several coats of carnauba wax. I buffed it with a clean buffing pad and then with a microfibre cloth. The finished pipe is shown in the photos below. The unusual shape and the unique grain on the briar really stand out with the finish I chose. The slight bend to the stem gives it a jaunty look. The stem is too heavy for the bowl to sit flat on the angled base but it balances on the point.