A Badly Broken Butz-Choquin Pipe makes its way back to me for Repair and Restoration


Blog by Steve Laug

Back in August of 2018 I worked through the pipes in the estate of George Koch and one of them was an interesting Butz-Choquin Simour Pot that had a piece of copper inlaid into the back of the bowl on the left side. The stamping on the left side of the shank read Butz-Choquin and underneath it is a bit more faint but looks to read Simour. On the right side it was stamped St. Claude over France and a shape number 1507 beneath that. I was a great looking pipe when I finished. Here is the link to the blog on the pipe (https://rebornpipes.com/2018/08/16/bringing-a-butz-choquin-simour-1507-back-to-life/). I have included a photo of the pipe when I finished it and when it was sold to a fellow named Randy in North Carolina.Randy loved the pipe and thoroughly enjoyed smoking it. Here is where the story shifts to the journey of the pipe back to Canada.

I received an email from Randy early in December about the pipe he had purchased. It was in need of a repair. I include his email below.

Steve, I bought a pipe from you about a year ago. I think l paid around $60 for it. I dropped it off my deck and broke the shank. Is that something that can normally be fixed and would it be worth it when comparing the original cost vs whatever your repair is. generally speaking? I know you haven’t seen the it, just trying to get a general idea if you think it might be worth the expense.

I had Randy send me some photos of the pipe which due to computer issues on my old computer I know longer have but it was broken at the shank with a nasty break. We talked a bit back and forth by email and after the holidays he put it in the mail to me. I received it on Thursday late in the day and opened the package to see it up close and personal. The pipe was obviously a favourite of Randy’s and had been well smoked. The bowl had a thick cake and I needed to be able to see what was happening where the airway entered the bowl. I reamed it back with a PipNet pipe reamed so I could see it clearly. The shank had a thick build up of tars in the airway that made it hard to know what was happening with the airway from the break to bowl. I cleaned out the airway with a pick, knife and a lot of pipe cleaners and alcohol until was clean.I scrubbed down the externals of the bowl and the cracked shank area with alcohol, cotton swabs and pipe cleaners to remove the grime so that  I could work on the fit of the shank pieces together. The next photos show the cleaned bowl and shank pieces. It was a large chunk of briar that had broken off. I studied it for a while trying to figure out how I was going to repair it for him. Finally I figured out a plan. I would cut a piece of Delrin tubing and use it on the inside of the shank to provide a base to fuse the two parts together. The next photo shows the piece of Delrin. I needed to shorten the piece but it fit nicely in the shank and the broken piece.I roughed up the surface of the Delrin tube and glued it in the bowl half of the broken shank with black CA glue. I let it cure for a short period until the tube was solidly anchored in the bowl end.Once the tube was solidly in place. I gave the other end of the tube a coat of the black super glue and also coated the ends of the crack with clear super glue. The clear dries faster and that is what I wanted when I pressed the two halves together. I held them together until the glue cured and when it was finished I took the following photos. The depth of the crack for the shank end and the feather like rustications on the shank complicated the work a bit for me. I filled them in with clear CA glue so that the fit of the band would be solid. I filled in the crack with briar dust and clear CA glue until the surface of the crack was even with the surrounding briar on the shank.I sanded the shank repairs smooth with 220 grit sandpaper to prepare it for fitting the nickel band on the shank. My thinking was that the internal Delrin tube would stabilize the shank and the band on the outside would bind it together. Once it was cleaned off I knew I would need to do a bit more filling with briar dust but it was definitely getting there.   I fit the band on the end of the shank. It was snug so I heated the band with a lighter flame and pressed it onto the shank by pushing the shank end down on a piece of padding on my desk top. I pressed into place so that the edge of the band was at the edge of the shank. It was a tight fit and held the pieces of the repair in place from the outside. I sanded the repaired area above the band with a folded piece of sandpaper and then with micromesh sanding pads until it was smooth. I cleaned off the rim top with a pen knife to scrape away the lava build up. I polished it with 1500-12000 grit micromesh sanding pads. I cleaned up the beveled edge and the top until it was smooth. I restained the rim top and the shank repair with a Cherry and Walnut stain pen to match the rest of the pipe.   I worked some Before & After Restoration Balm into the surface of the briar with my finger tips to clean, enrich and enliven the briar. I let it sit on the briar for 15 minutes and buffed it off with a soft cotton cloth. I used a piece of 220 grit sandpaper to take some of the vulcanite off of the tenon to refit it to the shank of the pipe. Once a shank has been banded it compresses the diameter of the shank enough that the original tenon was too large to fit in the mortise. I slightly reduced it and the fit was perfect. I put it in place in the shank and took photos of the pipe at this point. I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. With the stem done it was time to put the pipe back together. From where it was when it arrived to where it is now is a long hard push and it is definitely a different looking pipe. While it is not flawless it should now give Randy a good smoking pipe that looks very good. The finish and even the band looks really quite good with the rest of the pipe. The finish hides the repair quite a bit and it is solid. I will send it back to Randy later this week. I am looking forward to what he thinks of the restoration. Thanks for walking through this with me.

6 thoughts on “A Badly Broken Butz-Choquin Pipe makes its way back to me for Repair and Restoration

  1. Pingback: Previous Repairs Can Wreak Havoc in a Restoration – Dunhill Shell Briar R F/T 1962 Pot | rebornpipes

  2. Maxi

    Amazing job.
    As a simple fan of restorations, I have doubts about where to get those metal hoops… In specialiality stores (ferreterías in Spain)?. Online. I have to look at the markers too.
    Thank you for your work

    Reply

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.