Redeeming a James Upshall P Grade Silver Banded Dublin


Blog by Steve Laug

Over the past two weeks I was traveling in Alberta with my brother Jeff and his wife, Sherry. In between work appointments and presentations we took some time to visit local antique shops and malls. We found quite a few pipes. In a small Antique Shop in Lethbridge we found a few interesting pipes. The third of the pipes that I have chosen to work on from that find is a beautifully straight grained Dublin. The taper stem has a JU in an oval stamped logo on the left side. The pipe was dirty and caked when we picked it up. The rim top had a little lava and some small scratches in the edges of the bowl. The bowl had a thick cake in it that was hard and dense. The exterior of the bowl and shank are very dirty with grime and oils from prolonged use. It was also dull and lifeless. The stamping on the left side of the shank was readable and read James Upshall in an oval. To the left of that stamping there was an upper case “P” grade stamp. On the right side of the shank it is stamped Tilshead over England over Made by Hand. The vulcanite stem was had tooth chatter and tooth marks on the top and the underside near the button. I took photos of the pipe before I started the cleanup. I took close up photos of the bowl and rim to capture the condition of the pipe before I started my cleanup work. The rim top had some lava build up on the edge and there were some small nicks on the inner edge. There was a thick cake in the bowl. Other than being so dirty it appeared to be in great condition. The silver band on the shank is tarnished. The stem was dirty and there was tooth chatter on the top and underside near the button and on the button surface itself. The stem was lightly oxidized.I took a photo to capture the stamping on the left side of the shank. The photo shows the stamping “P” followed by James Upshall in an oval. The stamping on the right side says Tilshead over England over Made by Hand.  The third photo below shows the JU Oval stamp on the left side of the stem.I wanted to educate myself about the Upshall brand so I turned first to one of my go to sites – Pipephil (http://www.pipephil.eu/logos/en/logo-j1.html). I have included a screen capture of the section on the site about Upshall pipes. The pipe I am working on it stamped exactly like the first one in the photo that follows.I turned then to Pipedia to garner some more details about the brand and Barry Jones I have included the link and various sections from that article (https://pipedia.org/wiki/James_Upshall). I quote:

…All our pipes are individually created by a team of highly skilled artisans, headed by Mr. Barry Jones, who is widely regarded as one of the best pipe carvers in the world, with more than 50 years experience in pipe making.

Mr. Jones learned his skill from the age of 15 in London and was personally guided by Mr. Charatan of Charatan Pipe Co., pipe makers to royalty since 1863. For years he was responsible for creating the majority of the famous Charatan shapes and the high standard of quality…

I quote from further down in the article:

…James Upshall gives a unique guarantee on each pipe leaving the workshop. No pipe bearing the name of James Upshall is marred by fillings and putty. Scarcity of good quality plateau briar and the time consumed turning by hand, limit our production, but we will always strive to fulfill the growing demand for James Upshall, quality and tradition at its best…

…As always the James Upshall pipe has been sold in the most prestigious outlets around the world and has been greatly appreciated by royalty, lords and celebrities alike. King Hussein of Jordan, Anwar Sadat, Bing Crosby, Yul Brynner and more recently Arnold Schwarzenegger, Robert Wagner and Tom Selleck to name but a few of the famous names who have helped to cement James Upshalls’ reputation as the Rolls Royce of Pipes.

Further down in the article there is a section on Grading and Sizing of James Upshall Pipes. I have quoted that entire section below. It helps to place the “P” grade stamp on the pipe that I am working. The information comes directly from the James Upshall website.

Grading & Sizing Information

James Upshall pipes are graded by various finishes, i.e. bark, sandblast, black dress and smooth etc. Then by cross grain, flame grain, straight grain and, last but not least, the perfect high grade, which consists of dense straight grain to the bowl and shank. The latter being extremely rare. In addition, the price varies according to group size, i.e. from 3-4-5-6 cm high approximately Extra Large. We also have the Empire Series which are basically the giant size, individually hand crafted pipes which come in all finishes and categories of grain. All our pipes are individually hand carved from the highest quality, naturally dried Greek briar. In order to simplify our grading system, let me divide our pipes into 4 basic categories.

  • It begins with the Tilshead pipe, which smokes every bit as good as the James Upshall but has a slight imperfection in the briar. In the same category price wise you will find the James Upshall Bark and Sandblast finish pipes, which fill and smoke as well as the high grades.
  • In this category we have the best “root quality” which means that the grain is either cross, flame or straight, which is very much apparent through the transparent differing color finishes. This group will qualify as the “S”- Mahogany Red, “A” – Chestnut Tan and “P” – Walnut. The latter having the straighter grain.
  • Here you have only straight grain, high grade pipes, which run from the “B”, “G”, “E”, “X” and “XX”. The latter will be the supreme high grade. Considering the straightness of the grain the latter category is also the rarest. Usually no more than 1% of the production will qualify.
  • Lastly, we have the Empire Series. These are basically Limited Edition gigantic individually hand crafted pieces, which again are extremely rare due to the scarcity of large, superior briar blocks.

We also offer a selection of finely engineered silver and gold banding for pipes. Bands are available in silver, 9ct and 18ct gold, the width can be 6mm or 10mm and they can be fitted flush or on the surface. Bands are finished in plain, engine turned with barley or line patterns and also in gold with large hallmarks.

I am also including a copy of an article from the Pipedia site about the brand and the maker provided by Doug Valitchka (https://pipedia.org/wiki/File:James_Upshall.jpg).

Barry Jones in the photo, and an interesting article, courtesy Doug Valitchka

While we were traveling I decided to do a bit of work on some of the pipes that we had found. This was the third one that I worked on. I scraped the inside of the bowl with a sharp knife. I scraped the tars and lava off the top of the rim with the same knife. I scrubbed the exterior of the bowl with warm water and Dawn Dish Soap to remove the buildup of tars and grime around the bowl and on the rim top. I rinsed it well and wiped the bowl down with a clean paper towel to polish the finish on the bowl. The pictures that follow show the condition of the pipe after it had been scrubbed. When I got it home I would scrub the exterior and the interior some more. When I returned from my trip I cleaned the tarnished silver with silver polish and a jeweler’s cloth. I wanted to get it cleaned off to see if there were any stampings on the silver. It was stamped STERLING on top of the band which correlates to the not in the article from Pipedia where Upshall used Sterling Silver bands on some of their pipes.I followed up on my initial cleaning of the bowl and shank. I reamed the bowl with a Savinelli Fitsall pipe knife to remove the remnants of the cake in the bowl. I sanded the bowl with 220 grit sandpaper wrapped around a piece of dowel to smooth out the inside walls of the bowl.I scrubbed out the mortise and the airway in the shank, the metal mortise and the stem with alcohol, cotton swabs and pipe cleaners.I polished the briar with micromesh sanding pads – wet sanding the bowl walls and rim top with 1500-12000 grit pads. I wiped the bowl down after each sanding pad with a damp cloth to wipe of the dust. I scrubbed the bowl down with Mark Hoover’s Before & After Briar Cleaner. I rubbed it into the surface of the briar, and as Mark wrote me it lifted the grime and dirt out of the briar. I rinsed the cleaner off the bowl with warm running water and dried it with a soft cloth. The photos below show the cleaned briar… Look at the grain on that pipe! I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned my attention to the stem. I sanded out the tooth chatter with 220 grit sand paper and started to polish it with a folded piece of 400 wet dry sandpaper. Once it was finished it began to shine. I used some Antique Gold Rub’n Buff to restore the stamping on the left side of the stem. I pressed it into the indentations on the stamp with a tooth pick. I set it aside to dry and let it sit for a few minutes. Once it had cured I rubbed it off with a cotton pad and polished it with micromesh sanding pads.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with a damp cloth. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. This is a beautifully grained Upshall Dublin with a black tapered vulcanite stem. It has a great look and feel. The shape is very tactile and is a beauty. I polished stem and the bowl with Blue Diamond polish on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The grain on the bowl came alive with the buffing. The rich contrasting browns works well with the polished vulcanite stem. The finished pipe has a rich look that is quite catching. Have a look at it with the photos below. The shape, finish and flow of the pipe and stem are very well done. The dimensions are Length: 6 ½ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. Thanks for walking through the restoration with me as I worked over the next of the finds of Jeff and my Alberta pipe hunt. It is a beautiful straight grain Hand Made Dublin with a Sterling Silver band and vulcanite stem.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.