Finishing up a Stanwell de Luxe Regd No. 969-48 Shape 482 for Paresh


Blog by Steve Laug

Not long ago I was speaking with Paresh and Abha on Facetime and they showed me a Stanwell de Luxe 482 that they had been working on. It was cleaned and ready for restoration. Paresh had filled in the multitude of nicks and dents in the briar with super glue and briar dust. He was not happy with the freckled appearance of the briar once he had finished his repairs. The super glue was very runny and had gone all over the bowl leaving darkened patches where ever it ran all around the bowl. Kind of a mess. There were also some fine pin hole nicks in the shank that were around the stamping. He wanted me to pick up where he had left off and finish the pipe for him. The pipe was stamped on the left side of the shank Stanwell over Regd. No. 969-48 over de Luxe. ON the right side it was stamped Fine Briar over the shape number 482. Working on this pipe was truly not a bad deal for me as it was completely cleaned up by Abha and the stem was cleaned and partially finished as well. It would be interesting to see what I could do with it. When the pipe arrived this is what it looked like. I took some close up photos of the rim top and the bowl from various angles to show the freckled appearance that Paresh was speaking about. I carefully wiped the bowl down with acetone on a cotton pad to remove the excess glue that had run and also the stain that remains in the briar without damaging the repairs. The repair spots begin to show clearly. There are still spots on the shank that need to be dealt with. I sanded the surface of the bowl with 220 grit sandpaper to smooth out the repairs and remove the marks from the runny glue. I polished the briar with micromesh sanding pads – wet sanding with 1500-2400 grit pads and dry sanding with 3200-4000 grit pads. I wiped it down after each pad with a damp cloth. I also used the tip of a dental pick to fill in the many tiny sandpits in the sides of the shank. Once the glue cured I sanded them smooth with the tip of a sanding stick and folded sandpaper. Once the fills were blended into the surface of the shank I polish the shank portion again with the micromesh sanding pads. I stained the bowl with Fiebing’s Tan Aniline stain. The stain is a brownish red colour and should help to hide the many repairs to the bowl.Once the stain had dried to touch I wiped the bowl down with a cotton pad and alcohol. I wanted the stain to be transparent and allow the grain to shine through but still be opaque enough to hide the repairs that both Paresh and I had done. I rubbed down the briar with Before & After Restoration Balm. I worked it into the smooth surface of the briar with my fingertips to clean, enliven and protect it. I let the balm sit for a little while and then buffed the bowl with a cotton cloth to raise the shine. The following photos show the bowl at this point in the restoration process. The grain is really starting to stand out. There were still some grooves near the button that needed to be dealt with before I would be happy with the stem. I sanded the grooves out with 220 grit sandpaper until they were smooth.I polished the stem with micromesh sanding pads to remove the scratches. I wet sanded with 1500-2400 grit sanding pads and dry sanded with 3200-12000 grit pads. I wiped the stem down with Obsidian Oil after each sanding pad. I polished stem and bowl with Blue Diamond to polish out the remaining small scratches. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The rich reds of the tan stain work well to blend in the majority of the fills in the briar. The pin hole nicks in the finish have almost all been repaired and blended in with the stain coat. The grain really stands on the finished bowl and shank. The polished black vulcanite stem works together with the beautiful grain in the briar to give the pipe a rich look. The finished pipe is shown in the photos below. The dimensions are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 1/4 inches, Chamber diameter: 3/4 inches. The pipe is ready to head back to Paresh in India once I have finished a few more projects for him. Thanks for walking through the restoration with me as I worked over this beautiful little Stanwell.  There were two larger factory fills in the bowl that were rock hard and not workable. I could not pick them out or get the stain to permeate the putty. They are visible in the next two photos. Ah well they will remain in the finished pipe.

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.