Blog by Steve Laug

The next pipe I am working on was purchased on 01/26/18 from an eBay seller in Akron, Ohio, USA. It is stamped on the left side of the shank and reads Stanwell [over] Regd. No. 969-48 [over] Royal Guard. It is stamped on the left side with the shape number 22. On the flattened underside of the shank it is stamped Made in Denmark. There was a thick cake in the bowl, debris in the bottom and on the bowl walls and some remnants of tobacco. The airway was dirty and tarry and there was a hairline crack in the thin underside of the shank. There was a light lava overflow on the back of the crowned rim top. The crowned and inwardly beveled rim top looked to be in good condition. The outer edge actually looked quite good with no visible damage. The finish was dirty and dusty and with grime ground into the sides and heel of the bowl. The stem looked fairly good but underneath the calcification and oxidation the tooth marks and chatter looked minimal. There was a gold Stanwell S Crown on the left side of the half saddle. When the stem was removed it was clear that it was a filter pipe. Jeff took photos of the pipe before he started his cleanup work on it. Jeff took close-up photos of the bowl and rim top to show the cake in the bowl. The rim top shows some thin lava spots on the smooth finish. The inner edge of the bowl also had some lava buildup. The outer edges of the bowl look very good. He took photos of the top and underside of the stem surface and button to show its general condition. It looked very good under the spotty oxidation. Jeff took a photo of the heel of the bowl and the shank to give a sense of the grain around the bowl sides. It is gorgeous looking pipe that has grain that chases the shape of the bowl. It should clean up very well.He took photos of the stamping on the shank sides. They are clear and readable as noted above. There was no photo included of the right side of the shank and the shape number there. The Crown Stanwell Logo was clear on the left side of the half saddle stem. It was interesting that the Royal Guard had that stem logo rather than the typical RG logo. Jeff took a closer photo of the hairline crack on the shank. It started on the thin bottom side of the shank end and curved upward through the Made in Denmark stamping before it disappears. I turned to Pipedia to see if there was any clear information on the Royal Guard line of pipes (https://pipedia.org/wiki/Stanwell). I found the Royal Guard listed under the second lines of Stanwell pipes listed there.

I then followed a link there (https://pipedia.org/wiki/Stanwell_Shape_Numbers_and_Designers). It took me to an article on Shape numbers and Designers. I quote from that below.

22. Two versions of this shape number:

a) Straight billiard with an oval shank and a tapered stem (early 1950s – see catalog).

b) Bent apple-horn hybrid with a half-saddle stem.

From that information I knew that I was working a 22 B – a bent apple-horn hybrid with a half-saddle stem. There was list of designers below that included the 22 in pipes designed by Sixten Ivarsson. The problem was that I did not know if it was referring to the a) or the b) design. Now it was time to work on the pipe.

Jeff had done a great job cleaning up the pipe as usual. He reamed the pipe with a PipNet reamer and cut back the cake back to the bare briar. He cleaned up the walls with a Savinelli Fitsall Pipe Knife. He scrubbed the interior of the bowl and shank with pipe cleaners, cotton swabs and alcohol to remove the tars and oils. He scrubbed the exterior of the pipe with Murphy’s Oil Soap and a tooth brush to remove the grime from the finish. He worked on the rim top lava and darkening with the soap and tooth brush. He scrubbed the inside of the stem with alcohol and pipe cleaners. He scrubbed the exterior with Soft Scrub and then soaked it in Briarville’s Pipe Stem Deoxidizer. He washed it off with warm water to remove the Deoxidizer. The pipe looked far better when it arrived. I took photos of the bowl and rim top as well as the stem to show how clean they were. You can see that rim top and edges look very good. The stem is clean and the tooth and chatter on both sides ahead of the button is very light.I took photos of the stamping on the sides of the shank. The stamping is readable as noted above. Royal Guard was a Stanwell second and generally was not stamped Stanwell. This one was! The stem on the Royal Guard was also stamped RG and this one bears the Stanwell Crown S.I took a photo of the pipe with the stem removed to show that the tenon was drilled for a filter. I tried to fit a 9mm filter but it did not work. My guess is that it takes Vauen Dr Perl Junior 6mm size filter. I tried a Dr. Grabow 6mm filter it fit well but was too long. I would trim a Grabow filter to fit the proper length and whoever adds it to their collection will be able to use it until they are able to get some of the ones in the photo below. I also took a photo of the bowl and stem to get an overall look of stem, tenon and profile of the pipe. It really is a beautifully shaped pipe. I decided to start my work on the pipe by dealing with the cracked shank. I chose not to drill the crack end so as not to damage the stamping. Instead I put some glue on the cracked shank and held it in place until the CA glue set. I hand fit a band to the shank end. It sounds simple but it was an interesting challenge. The bottom edge of the shank was very thin which I think is why it cracked. There was no extra briar to work with. The other piece of the puzzled was that the bottom of the shank was flattened and the shape was not round any more. I went through my bands and found the one that had the proper diameter. It also had a curved edge that covered the shank end and would provide some extra thickness to the thin bottom of the shank. I gave the band a rough shaping by hand then put it on the shank and used a small furniture hammer to fit it smoothly to the shank shape. It fit nicely and it firmly held things in place.  I used a folded pipe cleaner to paint the shank end with all purpose glue and then pressed the band in place on the glue. I took photos of the newly fitted band. It looked very good at this point and the crack was pressed together tightly. I polished the briar with micromesh because it was in such good condition. I polished it with 1500-12000 grit micromesh sanding pads. I wiped the bowl down after each sanding pad with a damp cloth. I rubbed the briar down with Before & After Restoration Balm. I worked it into the briar with my fingertips. The product works to clean, enliven and preserve the briar. I let it sit for 10 minutes while I worked on the stem. After the time passed I buffed it with a cotton cloth to deepen the shine. The briar really comes alive with the balm. I set the bowl aside and turned my attention to the stem. I have a box of Dr. Grabow 6mm filters so I took one out of the box, shortened it to fit and inserted it in the tenon. The fit is perfect and fills in the tenon. I then used some White Acrylic Fingernail Polish to touch up the white that remained in the Crown S stamp on the top of the stem. The S and part of the crown looked much better. There were some light spots on the top of the crown but otherwise it looked good. I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I wiped the stem down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I gave it a coat of Obsidian Pipe Stem Oil. It works to protect the stem from oxidizing. I set it aside to dry. This Sixten Ivarsson designed Stanwell Royal Guard 22 Bent Apple/Scoop with a half saddle vulcanite stem turned out very nice. The mix of brown stains highlights the grain around the bowl sides and bottom. The rim top and edges look very good. The finish on the pipe is in excellent condition. The thin brass band on the shank end looks good and adds strength to the shank stem fit. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Stanwell Royal Guard 22 is very nice and feels great in the hand and can be used as a sitter with the wide base. Give the finished pipe a look in the photos below. It is a nice pipe whose dimensions are Length: 5 ½ inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 57 grams/2.10 ounces. Thanks for walking through the restoration with me as I worked over another beautiful pipe. This one will be going on the rebornpipes store, in the Danish Pipe Makers Section shortly. If you are interested in adding it to your collection let me know by message or by email to slaug@uniserve.com. Thanks for your time.

As always, I encourage your questions and comments as you read the blog. Thanks to each of you who are reading this blog. Remember we are not pipe owners; we are pipe men and women who hold our pipes in trust until they pass on into the trust of those who follow us.