Tag Archives: Royal Danish Canadian

An Easy Restore – A Royal Danish 984R Canadian

Blog by Steve Laug

Along with the recent Kaywoodie Original (https://rebornpipes.com/2019/01/25/new-life-for-a-kaywoodie-original-imported-briar-freehand-stack/) that I worked on, my brother Jeff sent me a nice looking multi finished Canadian. It is a classic Danish version of the Canadian shape with an oval shank and a long tapered stem. The pipe is sandblasted with two smooth patches on the sides of the bowl. It is a nice looking pipe that looks a lot like the variegated finished pipes that Stanwell issued in the 60s and 70s. The underside of the shank is stamped Royal Danish in script followed by Made in Denmark and finally the shape number 984R. Like the other pipes that came from this Idaho auction the pipe was in pretty decent condition – dirty but really not too bad. The finish was dusty and dirty with grime worked into the sandblast finish. The bowl had a moderate cake in it but it did not go all the way to the bottom of the bowl – in fact the pipe was not even broken in. The rim top had a thick coat of lava and was dirty. The inner and outer edges of the bowl were in great condition. The stem was oxidized but in decent condition. Jeff took these pictures of the pipe to show its condition before he started his cleanup work.Jeff took a close up of the bowl and rim. The bowl had a moderate to medium cake but the lava overflow onto the rim top was quite thick. He also took a close up photo of the side and underside of the bowl and shank.On the underside of the shank the stamping was very clear and readable. It is stamped in a smooth panel that runs from the heel of the bowl to end of the shank. The Royal Danish Brand is a Stanwell second line. It is no wonder that the pipe looks very similar to a Stanwell. The shape number is also a Stanwell shape number.He took photos of the stem to show the oxidation on the stem. The first photo shows the faint/light Royal Danish Crown on the top side of the taper near the shank. The second and third photo show the oxidation and the otherwise pristine stem surface. Jeff had reamed the bowl with a PipNet pipe reamer and followed up with a Savinelli Fitsall pipe knife to remove the cake. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim, shank and stem with a tooth brush and Murphy’s Oil Soap to remove the oils and tars on the bowl, rim and shank. He rinsed it under running water. He dried it off with a soft cloth. He was able to remove the majority of darkening on the rim top without harming the finish underneath it. Without the grime the finish looked good. Other than the light oxidation, the stem was actually in pretty good condition and would only need to be polished. I took photos of the pipe to show its condition before I started my work on it. I took close up photos of the rim top that shows the clean bowl and the remaining lava in the grooves of the sandblast rim top. The stem was clean and Jeff had used Before & After Deoxidizer to soak and remove much of the oxidation. He rinsed out the inside of the stem and rinsed off the exterior as well. The photos of the stem show how good the stem actually looked after this treatment. I used a brass bristle wire brush to clean up the rim top of the bowl and loosen the remaining debris and dust in the grooves of the blast.I rubbed the bowl down with Before & After Restoration Balm into the sandblast finish of the bowl and the shank to deep clean the briar. I worked it into the smooth portions the sides and the bottom of the bowl. The product works to clean, enliven and protect the briar. I hand rubbed it with my fingers and wiped it off with a soft cloth. I buffed the bowl with a horsehair shoe brush to polish it. The briar really began to have a rich shine. I took some photos of the bowl at this point to mark the progress in the restoration. The stem was in really good condition so I skipped sanding it with 220 grit sandpaper. I polished the stem with micromesh sanding pads – wet sanding it with 1500-2400 grit pads and dry sanding it with 3200-12000 grit pads. I wiped the stem down after each pad with a damp cloth to remove the sanding dust. I used the Before & After Pipe Polish to remove the small minute scratches left in the vulcanite. I finished by wiping the stem down with a final coat of Obsidian Oil and set it aside to dry. I polished the stem with Blue Diamond to polish out the remaining small scratches and gave it several coats of carnauba. I polished the bowl and shank with Conservator’s Wax and buffed it with a shoe brush. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed it with a microfiber cloth to deepen the shine. The pipe polished up pretty nicely. The finished pipe is shown in the photos below. The dimensions are Length: 6 1/2 inches, Height: 2 inches, Outside diameter of the bowl: 1 3/8 inches, Chamber diameter: ¾ of an inch. I will be adding it to the rebornpipes store shortly. If you are interested in adding it to your collection email me at slaug@uniserve.com or send me a message on Facebook. Thanks for walking through the restoration with me as I worked over this beautiful Stanwell made Canadian.