Tag Archives: Edward’s Unique Pipes

Next on the table is a very unique Edward’s Algerian Briar 734

Blog by Steve Laug

The next pipe on the work table is another unique one that I chose out of my boxes of pipes to restore. I am not even sure what to call the shape. It has an acorn shaped bowl. The shank is domed shape with flat bottom. The graceful curves of the shank and bowl give it a very unique shape. The bowl had a thick cake and lava overflow on the rim. The rim top was crowned with small thin flat top. The bowl was smooth and a natural finish. The finish was dusty and tired but there seemed to be a shiny coat of something on the finish – perhaps shellac. The bowl had some nice grain under the grime and the finish appeared to be in good condition. There were a few fills on the right side of the bowl and some sandpits as well. A lot would be revealed once Jeff had worked his magic on it. The stem was dirty but came with tooth chatter and marks near the button on both sides. Jeff took photos of the pipe before he started his cleanup work. Jeff captured the condition of the bowl and rim top with the next series of photos. You can see the work that is ahead of us in the photos. The cake is very thick and heavy. The rim looked like it might have some damage on the back inner edge of the bowl. Jeff took some great photos of the sides of the bowl and heel showing what is underneath the grime and debris of time and use. You can see the fills in briar on the right side. They really stand out in the first photo. It will be interesting to see what happens as the pipe is cleaned and restored. He captured the stamping on the sides of the shank and the underside of the saddle stem. They are clear and readable. The left side reads Edwards. On the right side it reads Algerian Briar 734. On the underside of the stem it is stamped France. The next two photos of the stem show the top and underside of the stem. You can see the tooth marks and chatter on the surface of both sides.I took it out of the box from Jeff and looked it over. He cleaned the pipe with his usual penchant for thoroughness. When I took it out of the box I was amazed at how good it looked it really looked like a different pipe. He reamed it with a PipNet pipe reamer and cleaned up the reaming with a Savinelli Fitsall Pipe Knife. He scrubbed out the internals with alcohol, pipe cleaners and cotton swabs until the pipe was clean. He scrubbed the exterior of the bowl with Murphy’s Oil Soap and a tooth brush to remove the grime and grit on the briar and the lava on the rim top. The bowl looked very good. Jeff scrubbed the stem with Soft Scrub to remove the grime and soaked it in Before & After Deoxidizer. When he took it out of the soak it came out looking far better. I took photos before I started my part of the work. I took some photos of the rim top and stem. The rim top is clean but there is a lot of damage to the inner edge and top on the back right side. The bowl itself looks very clean. The rest of the inner edge is a little rough but not damaged. The close up photos of the stem shows that is it very clean and other than being dull it looks very good.I took photos of the stamping because they had cleaned up very well.I decided to take care of the damage on the rim top and inner edge first. I topped the bowl on a topping board with 220 grit sandpaper. I then cleaned up the inner edge with a folded piece of 220 grit sandpaper and gave it a slight bevel. I filled in the small pits on the right side of the bowl with clear super glue. Once the repair was cured I sanded smooth with a folded piece of 220 grit sandpaper to smooth it out.I polished the briar and the shank with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I was able to blend in the repairs into the side of the bowl. I wiped the bowl down after each pad with a damp cloth. The grain really began to stand out and the finish took on a shine by the last sanding pad. The photos tell the story! I worked some Before & After Restoration Balm into the surface of the smooth briar with my fingertips. The product works to clean, enliven and protect the briar. I let the balm sit for about twenty minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned to deal with the stem. I “painted” the surface of the stem with the flame of a Bic lighter to lift the tooth marks. I was able to lift them a lot.I filled in the remaining tooth marks on the surface of the stem with clear super glue. I sprayed it with an accelerator to harden it. Once it had hardened I sanded it with 220 grit sandpaper and 400 grit wet dry sandpaper to blend it into the surface of the vulcanite. I polished the stem with some Denicare Mouthpiece polish – a red gritty paste that feels a lot like the texture of red Tripoli. It works well to polish out some of the scratches. I find that it does a great job preparing the stem for polishing with micromesh sanding pads.I polished the vulcanite stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with a cloth containing some Obsidian Oil. I finished polishing it with Before & After Pipe Stem Polish – both Fine and Extra Fine and buffed it off with a cotton cloth. This Edward’s Unique Algerian Briar was another fun pipe to work on and I really was looking forward to seeing it come back together again. With the grime and debris gone from the finish it was a beauty and the grain just pops at this point. I put the stem back on the bowl and buffed the pipe with Blue Diamond on the buffing wheel. I carefully avoided the stamping on the shank during the process. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing it with a clean buffing pad on the buffer. I hand buffed the pipe with a microfiber cloth to deepen the shine. The rich natural finish on the bowl looks really good with the polished black vulcanite stem. It is very well done. Give the finished pipe a look in the photos below. I can only tell you that it is much prettier in person than the photos capture. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: ¾ of an inch. The Edward’s pipes I have worked on always have had a creative flair. This is truly another unique looking Edward’s. Thanks for walking through the restoration with me as I worked over another beautiful pipe. I will be adding it to the rebornpipes store soon. If you want to add it to your collection send me an email or a message! Thanks for your time.

Refurbishing an Edwards Unique – I have no idea what to call the shape

6 Replies

Blog by Steve Laug

The next pipe on the work table is a really uniquely shaped Edwards. It is even hard to describe what the shape is – a snail, a tooth, a blowfish with legs??? I have no idea what to call it. I reread one of the blogs I wrote on an Edwards I restored and there is a very appropriate quote there describing this pipe (https://rebornpipes.com/2016/10/18/my-latest-refurb-an-edwards-algerian-briar-771-is-not-a-shape-ive-seen-before/). I quote:

…The available shapes that the pipes came out it spoke of a very fluid design philosophy. Pipedia says that “Edward’s Design Philosophy is hard to pin down, think of their style as the “American Charatan” with unique & clever twists all their own.”

Jeff picked Edwards in an auction in Oklahoma. It caught his eye and as he watched the auction he decided it was meant to be ours. Neither of us has ever seen one like this. The finish was very dull and seemed to have remnants of shellac on the surface in spots. The smooth sides, front, back, heel and rim top work well with the unique rustication on the shank bottom and top. There is a vulcanite shank extension on the end of the shank. The shape is flat on both sides of the bowl and rounded on the top, front and back. The bottom has four feet on it. The stamping on the left side of the shank reads Edward’s in script. On the right side of the shank it is stamped Algerian Briar. On the heel of the bowl it is stamped EF1 over Handmade. The bowl was lightly smoked with no cake. There was no lava overflow and the rim edges were in great condition. The stem and shank extension were lightly oxidized. There was light tooth chatter and tooth marks on the top and underside of the stem near the button. He took some photos of the rim top and bowl from various angles to give me a clear picture of the condition of the rim top and bowl. You can see the minimal cake in the bowl and the clean rim top. It looked like a pipe that had hardly been used. It must have been sitting in someone’s cupboard for a long time to accumulate the dust and debris in the bowl and in the rusticated portions. Jeff took some photos of the sides and heel of the bowl to show the condition of the finish on the pipe. The shellac coat appears to have gone cloudy on the surface of the briar. The photos show mixed grain on the sides, heel and rim of the pipe. Under the cloudiness of the finish it was a nice looking bowl. The shape pretty well follows the flow of the grain. Jeff took two close-up photos of the rustication on the shank top and bottom. It is almost like scales it is very well done and interesting looking. It is very tactile.He took some photos of the stamping on the shank. The stamping was readable and clear. On the left side you can see Edward’ stamped in a smooth band. On the right side it is stamped Algerian Briar. On the heel of the bowl is stamped EF1 and Handmade. I wonder if EF1 is a designation for Edwards Freehand pipes. There is also a smooth band of briar between the vulcanite shank extension and the shank. He also included a photo of the rustication on the bottom of the shank to show its uniqueness. The next two photos show the top and underside of the stem. It is dirty and has calcification on both sides at the button. There is also some tooth chatter and some light tooth marks. The third photo shows the curve of the full stem. The final photo shows the fancy turning of the chair-leg style stem. Jeff took a photo of the stem removed from the shank to show the shank extension and tenon of the pipe. You can see the dust and debris in the turns of the stem and shank in the photo.Across the board they were all Algerian Briar and all were unstained waxed or oiled briar. I remember reading that actually oil curing was a feature of their pipes. I did a quick look on Pipedia (https://pipedia.org/wiki/Edward’s) and found that I was correct. I quote:

Edward’s pipes were originally produced in St. Claude France when France actually was a world-class pipe maker with longstanding business & political connections to Colonial Algeria that allowed them to obtain the finest briar.

During the tumultuous 1960’s, Edward’s created a business model to offer the finest briar available in both Classic and Freehand shapes – all at a fair price. They bought the company & equipment and cornered the market on the finest, choice Algerian Briar just before the supply vanished in political turmoil of Algeria’s independence. Edward’s packed up both machinery and briar-treasure to America, safely caching the essentials to create a new pipe-making dynasty. This was a coup, for the 70’s and 80’s were grim years for pipe smokers as quality briar all but disappeared.

All of Edward’s pipes are Algerian Briar – a fact very few pipe companies can claim, and all are oil-cured utilizing natural finishes – no strange concoctions are used to interfere in your tastebud’s dance with the briar. Algerian, Calabrian, Sardinian, Corsican – take your pick, but Algerian Briar is generally considered the finest smoking briar ever used. When combined with oil-curing, Algerian takes on a magical quality that even Alfred Dunhill recognized as far back as 1918 as the choice for both his Bruyere and Shell.

With that information on the brand in hand I turned to the pipe. Jeff had done his usual thorough job cleaning the pipe which I really appreciate because of the freedom it gives me in dealing with pipes. He reamed it with a PipNet pipe reamer and got rid of the cake. He cleaned up the reaming with a Savinelli Fitsall Pipe Knife so that we could see the walls of the bowl and assess for damage. He cleaned the internals of the shank and stem with alcohol, pipe cleaners and alcohol. He wiped down the surface with acetone to remove the shellac coat. He scrubbed the exterior with undiluted Murphy’s Oil Soap and a tooth brush. He rinsed the pipe under warm water. He dried it off with a cloth and then let it air dry. The stem was scrubbed with Soft Scrub and had a soak in Before & After Deoxidizer to remove the oxidation. One it was rinsed off, it came out looking very good. The finish on the bowl and the rim top cleaned up nicely. I took pictures of the pipe to show how it looked when I unpacked it. I took a close up photo of the rim top to show how clean it was. You can see that it has a few small nicks but otherwise the rim top looks flawless. The stem looked good just some light tooth chatter and marks near the button. Overall the pipe is a beautiful looking piece. I took photos of the stamping on the sides of the shank. It read as noted above. It is very clear and readable.Because the pipe was in such good condition there was little rehabilitative work to do on the bowl or rim. I started my work immediately by polishing the briar with micromesh sanding pads – wet sanding with 1500-12000 grit pads and wiping down the briar after each sanding pad with a damp cloth. The briar began to shine. I worked some Before & After Restoration Balm into the briar with my finger tips and a horsehair shoe brush. The product is a great addition to the restoration work. It enlivens, enriches and protects the briar while giving it a deep glow. It is a product I use on every pipe I restore. I set the bowl aside and worked on the stem. I sanded out the light tooth marks and chatter with 220 grit sandpaper and polished the stem with 400 grit wet dry sandpaper.I polished the stem with Denicare Mouthpiece Polish from a tin of it I have in the drawer here. It is a gritty red paste that I rub on with my finger tips and work it into the surface of the stem and button and buff it off with a cotton pad. It gives me a bit of a head start on the polishing work.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I buffed the stem with a soft cloth to raise the shine. I gave it a final wipe down with Briarville’s No Oxy Oil to protect the stem from UV and slow down future oxidation. I don’t know what it is about finishing a restoration but I have to tell you that it is my favourite part of the process. It is the moment when everything that I have been working on comes together. I can compare it to where I started and there is always the satisfaction that it does indeed look better than when Jeff and I picked it up. As always I put the pipe back together and carefully buffed it with Blue Diamond on the buffing wheel. I gave the bowl and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad and hand buffed it to raise the shine. It is fun to see what the polished uniquely shaped Edward’s Freehand looks like along with the polished fancy vulcanite stem. This is nice looking pipe and I am sure that it will be comfortable in hand when smoking as it is light and well balanced for a pipe of this size. Have a look at it with the photos below. The dimensions are Length: 5 ¾ inches, Height: 1 7/8 inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. It is another beautiful pipe and one that will be staying with me in my collection. I have worked on a lot of Edward’s pipes over the years but I have never seen one shaped like this one.Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.