Daily Archives: June 30, 2016

Dunhill 488 Root Briar Restoration (1977)


By Al Jones

I’ve had several Dunhill pipes in my collection and on my work bench, but this is my first Root Briar. This one was offered by an eBay seller in Indonesia and it didn’t get much attention, and it was won for a modest final bid.

Pipedia says this about the Root Briar finish:

Root Briar
1940, Shape #48 saddle bulldog in Root finish, G.L. Pease collection[12]
1932 T113 Billiard in Root Finish, showing “Bowling Ball” stem and Vernon tenon
. Introduced in 1931 and highly prized because the grain is more pronounced in this finish. The Root Briar finish required a perfectly clean bowl with excellent graining. Therefore, it is the most expensive of the Dunhill pipes. Corsican briar was most often used for the Root finish, since it was generally more finely grained. This is a rare finish, due to the scarcity of briar suitable to achieve it. These pipes are normally only available at Company stores, or Principle Pipe Dealers.

The seller had posted many good pictures of the pipe and it appeared to only require a mild clean up.

Three weeks later, the pipe was delivered and I finished it this evening. Below is the pipe as it was received. The pipe weighs 46 grams. It does not have a size stamp, but I would say it is a size 4.

Dunhill_488_RB_Before (1)

Dunhill_488_RB_Before (4)

Dunhill_488_RB_Before (3)

Dunhill_488_RB_Before (2)

The pipe was used with the metal filter tube and it was interesting to find that there was little or no tar build-up in the shank. I assume the tube tranferred the smoked tobacco directly up the stem. The tube was a bit bent, so it was discarded. Today, most Dunhill pipe enthusiasts do not use the filter tube. There was some mild cake in the bowl and the stem had some light oxidation. There was a little rim darkening.

I removed the mild cake and soaked the bowl with alcohol and sea salt. The stem was soaked in a mild Oxy-clean solution.

The briar was shined with White Diamond followed by several coats of carnuba wax. The stem was shined with 800 grit wet paper followed by 1500 and 2000 grades, then 8000 grade micromesh. This was done with the stem mounted on the bowl. The stem was then buffed with White Diamond and Meguiars Plastic Polish.

Below is the finished pipe.

Dunhill_488_RB_Finish (1)

Dunhill_488_RB_Finish (5)

Dunhill_488_RB_Finish (4)

Dunhill_488_RB_Finish (2)

Dunhill_488_RB_Finish (6)

Dunhill_488_RB_Finish (3)

Dunhill_488_RB_Finish (7)

?

?

?

?

Dunhill_488_RB_Finish (9)

Dunhill_488_RB_Finish (1)

Finally a simple clean up – an Alco Universal Gold Pipe


Blog by Steve Laug

The Alco pipes were made by Falcon in England. This particular version of the Alco was made to hold an in line triple air groove filter. All Alco bowls are interchangeable with any other Alco, but NOT with Falcon. The Alco I was given is an Alco Universal Gold pipe. The pipe was in decent shape with the finish on the bowl in good shape but dirty. The rim had an abundance of lava overflow that came from a thickly caked bowl. There was tobacco debris stuck to the bottom of the bowl. The copper coloured base was dirty but did not show damage. The gold band was attached to the stem and showed some oxidation. The stem itself had a lot of tooth chatter on both the top and bottom sides near the button. What complicated that a little was that the stem was a dental bit and had two scored marks on each side. The airway in the stem was tight and the slot was narrow. The stem had a gold Falcon on the top side. The stamping on the underside of the base read ALCO UNIVERSAL.Alco1 Alco2The pipe came apart easily. I twisted the bowl off the base and found that there was a plastic spacer between the bowl and the base. The bowl had been stamped ALCO on the underside and it was dirty. The base had a lot of tars and oils that had hardened around the centre post. The stem also had the above mentioned “Triple Air Groove Filter”. Surprisingly the filter was pretty new looking.Alco3I cleaned out the airway in the stem with pipe cleaners, cotton swabs and alcohol. It was not as dirty as I expected. It made me wonder if the previous owner had not cleaned it a bit before he put in the new filter.Alco4The base was another story. It looked as if it had not been cleaned for a long time. I loosened the hardened oils and tar with a dental pick. I cleaned up the loosened debris with cotton swabs and alcohol and was able to remove the hardened tars and oils that had accumulated in the base over the years. I used cotton swabs, pipe cleaners and alcohol to clean out the inside of the mortise and airway in the shank.Alco5Reaming the bowl was a challenge as the cake was hard and dense. Starting with the smallest cutting head on the PipNet reamer and moving through the first three heads I reamed the cake back to bare briar. I cleaned up the bowl and airway at the bottom using the Savinelli Pipe Knife. Thinking about it as I write I probably should have tried out the Falcon Pipe Reamer that I picked up not too long ago. I forgot I had it so it will have to be used next time.Alco6 Alco7I scrubbed the base of the bowl and airway with cotton swabs and alcohol to remove the accumulated oils and tars on the bottom. You can see the ALCO stamping on the briar at the top of the picture.Alco8I worked on the rim with a cotton pad and saliva to remove the build-up there. It just took a bit of elbow grease to remove it and the undamaged rim came out of the grime. I wiped down the bowl with alcohol on the cotton pad and cleaned the dirt off the surface of the bowl and touched up the rim.Alco9I wet sanded the rim and bowl with 1500-2400 grit micromesh sanding pads and wiped it down again. I finished by sanding it with 3200-4000 grit pads to raise the shine. I put the bowl back on the base for the photo below.Alco10I have always found plastic stems harder to polish than rubber ones. The dental bit was a challenge to clean out all of the tooth marks in the grooves. I sanded the stem with 220 grit sandpaper to smooth out the chatter and then used 2000-6000 grit wet dry sandpaper to begin polishing it. I wet sanded it with 1500-2400 grit micromesh sanding pads and gave it a coat of Obsidian Oil. I dry sanded it with 3200-4000 pads, gave it another coat of oil and finished sanding it with 6000-12000 grit pads. I gave it a final coat of Obsidian Oil and let it dry.Alco11 Alco12 Alco13I have found that buffing plastic stems is more trouble than it is worth as the heat of the buffing pads can easily melt the stem and create a mess. I hand polished the stem with Meguiar’s Scratch X2.0 with cotton pads to bring up the shine. I buffed the bowl with Blue Diamond and gave it several coats of carnauba wax. I buffed the bowl with a clean buffing pad. I gave the stem several coats of Conservator’s Wax and hand buffed it and the bowl with a microfibre cloth. The finished pipe is shown in the photos below.Alco14 Alco15 Alco16 Alco17 Alco18 Alco19 Alco20