Blog by Steve Laug
This is another pipe that I have taken out of my personal collection as I just do not use enough to warrant keeping it. This pipe was one that I purchased long ago but have no memory where it came from. I don’t think I ever smoked it to be honest. It is a pipe I should have smoked as it is attractive enough but did not. It is time to move it on to someone who will enjoy it. The airway in the shank and the mortise are very clean. The smooth finish and rim top were in good condition. It appears that the bowl is coated with some varnish or shellac that I will remove. The inner edge of the rim is beveled inward. The finish was a very shiny but there appears to be some great grain poking through the shine. The stamping on the pipe on the left side of the shank reads Jobey in script [over] Tortoise. On the right side it is stamped with the shape number 115. The finish is a medium brown and with the varnish/shellac coat that is rough and uneven. Once it is removed the grain will show clearly. The colour of the stain goes well with the tortoise shell acrylic taper stem. There is a Jobey brass inset logo on the top of the stem. The stem is in excellent condition with no tooth chatter or marks on it. I took photos of the pipe before I did my clean up work on it to prepare it for you. I took a photo of the bowl and rim top to verify the description above. The beveled rim top and edges look good but there are some nick and scratches in the varnish/shellac coat. The bowl and edges are in good condition. I also took photos of the stem surface showing how clean it was on both sides. I took photos of the stamping on the sides of the shank. It is clear and readable as noted above. The Tortoise stamp on the shank matches with the tortoise acrylic stem.I took the stem off the bowl and took a photo of the pipe to give a sense of proportion of the pipe. You can also see shape of the pipe and some interesting grain on the briar. I decided to start my work on the bowl by dealing with the varnish/shellac coat. If it was either it would come off with acetone. I wiped the bowl down with acetone and a cotton pad to remove the rough shiny topcoat from the bowl. It looked significantly better when I finished. The shank and mortise were very clean and a quick run through with a pipe cleaner proved all that was necessary. I polished the rim top and the briar with micromesh sanding pads – dry sanding with 1500-12000 grit pads. There was a small sandpit on the front of the bowl about mid-bowl. I wiped the bowl down with a damp cloth after each sanding pad to remove the dust and debris. I gave the bowl and shank a coating of Before & After Restoration Balm. I worked it into the surface of the briar with my fingertips and a horsehair shoe brush to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned my attention to the stem. I polished it with micromesh sanding pads – 1500-12000 grit sanding pads and water to wet sand the stem. I wiped it down after each sanding pad with Obsidian Oil on a cotton rag after each sanding pads. But I find it does two things – first it gives some protection to the stem from oxidation and second it give the sanding pads bite in the polishing process. After finishing with the micromesh pads I rub the stem down with Before & After Fine and Extra Fine stem polish as it seems to really remove the fine scratches in the acrylic. I rub the Fine Polish on the stem and wipe it off with a paper towel and then repeat the process with the Extra Fine polish. I finished polishing the stem with a final coat of Obsidian Oil and set the stem aside to let the oil absorb. This process gives the stem a shine and also a bit of protection. This Jobey Tortoise 115 Billiard turned out to be a great looking pipe. With the shiny varnish coat removed from the pipe the grain shines through clearly. The tortoise shell acrylic stem is in excellent condition and works great with the polished briar. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and stem multiple coats of carnauba wax on the buffing wheel and followed that by buffing the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Jobey Tortoise Billiard fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 49 grams/1.73 ounces. It is a great looking pipe that I will soon be adding it to the rebornpipes store in the American (US) Pipemakers Section. If you are interested in adding it to your collection let me know Thanks for reading this blog and my reflections on the pipe while I worked on it.