Tag Archives: Sasieni Four Dot Moorgate S Pot

Cleaning up a Sasieni Four Dot Moorgate S Ruff Root Pot


Blog by Steve Laug

The next pipe on the work table is a Sasieni Four Dot Sandblast Pot. This Sasieni has a sandblast finish on the bowl and shank. The blast flows up and around the bowl and shank. The round shank flows well into Four Dot saddle stem. The pipe is stamped on a smooth panel on the underside of the shank and reads Moorgate S over Ruff Root on the heel of the bowl. That is followed by Sasieni over “Four Dot” followed by London Made over Made in England. The rim top is sandblasted and it is filled in with dust and light lava. There was a thick cake in the bowl. The pipe was dirty and dusty in all of the nooks and crannies of the sandblast. The saddle stem was vulcanite and had four dots on the left side of the saddle. There were tooth marks and chatter on both sides near the button. It was oxidized and had some calcification on the end. Jeff took some photos of the pipe to show the general condition of the pipe before he started his clean up. Jeff took some close-up photos of the rim top and bowl from various angles to show the overall condition. There is thick coat of lava in the grooves and valleys of the sandblast. You can also see the cake in the bowl. It was a well loved pipe and smoked a lot by the previous pipe man. Jeff took some photos of the sides and heel of the bowl to show the condition of the finish on the pipe. The photos show the beautiful deep sandblast around the bowl. Under the dust and grime it was a nice looking bowl. I think it will be a beautiful pipe once it is restored. He took photos of the stamping on the underside of the shank. It took two photos to capture the stamping from the heel to the shank stem junction. It was very readable and matches what was spelled out above.  He also took a photo of the four dots on the left side of the saddle stem. The next two photos show the top and underside of the stem. It is dirty, oxidized and has calcification on both sides at the button. There is also some tooth chatter and some tooth marks with some damage to the button edge on both sides. The third photo shows the flow of the stem and shank. I enjoy working on well-made Sasieni pipes and I find that their shapes and finishes are very well done. I was glad to be working on this one. When I received it Jeff had once again done an amazing job cleaning the pipe. He reamed it with a PipNet pipe reamer and got rid of the cake. He cleaned up the reaming with a Savinelli Fitsall Pipe Knife so that we could see the walls of the bowl and assess for damage. He cleaned the internals of the shank and stem with alcohol, pipe cleaners and alcohol. He scrubbed the exterior with undiluted Murphy’s Oil Soap and a tooth brush. He rinsed the pipe under warm water. He dried it off with a cloth and then let it air dry. The stem was scrubbed with Soft Scrub and soaked in Before & After Deoxidizer. It came out looking very good. The finish on the bowl and the rim top cleaned up beyond my expectations. I took pictures of the pipe to show how it looked when I unpacked it. I took a close up photo of the rim top to show how clean it was. Jeff had been able to clean out the dust and grime in the rim top and it looked very good. The inner edge of the rim and the ridges and valleys of the plateau looked good. The stem looked good just some light tooth chatter and several tooth marks on the button.Even the stamping cleaned up well and is still very clear and readable.Because the pipe was sandblast and so clean my work on the bowl was pretty minimal. I worked some Before & After Restoration Balm into the briar with my fingertips and a horsehair shoe brush. The product is a great addition to the restoration work. It enlivens, enriches and protects the briar while giving it a deep glow. I appreciate Mark Hoover’s work in developing this product. I set the bowl aside and turned my attention to addressing the issues with the stem. I sanded the surface of the stem with 220 grit sandpaper to remove the remaining oxidation and tooth chatter. I started the polishing process with 400 grit wet dry sandpaper.I polished the stem with Denicare Mouthpiece Polish from a tin of it I have in the drawer here. It is a gritty red paste (similar in grit to red Tripoli) that I rub on with my finger tips and work it into the surface of the stem and button and buff it off with a cotton pad. It gives me a bit of a head start on the polishing work.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I buffed the stem with a soft cloth to raise the shine. I wiped the stem down with Briarville’s No Oxy Oil to preserve and protect the stem surface. I am on the homestretch with this Sasieni Moorgate Ruff Root Four Dot sandblast Pot! As always I am excited to finish a pipe that I am working on. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I used a gentle touch to keep the polish from building up in the blast of the bowl. I gave the bowl multiple coats of Conservator’s Wax and the stem multiple coats of carnauba wax. I buffed the pipe with a clean buffing pad and hand buffed it to raise the shine. It is fun to see what the polished bowl looks like along with the polished vulcanite stem. This Sasieni Moorgate is a nice looking pipe. It is quite comfortable in hand and should be so when smoking. It is quite light and well balanced. Have a look at it with the photos below. The dimensions are Length: 5 ¼ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ½ inches, Chamber diameter: 7/8 of an inch. It is another beautiful pipe and one that will be on the rebornpipes store soon. You can find it in the section of Pipes by English Pipe Makers. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.