by Steve Laug

The next pipe is on the table is an interesting looking metal pipe with a briar bowl, metal shank tube and a rubber taper stem. We purchased it on 03/05/2021 from Antique Store in Logan, Utah, USA. The pipe is well shaped and has nice grain around the panelled bowl. Each corner on the bowl is rusticated from the top edged around the bottom of the bowl. It has a flat rim top and a heel on the bowl that slides over the metal tube. There is a screw that holds the bowl to the shank like those in Kirstens. The end of the metal tube has an end cap that is pressure fit in place. The pipe is stamped on the left side of the shank and Weaver [over] Pipes © [over] El Paso Texas USA [over] Pat. Pend. There was grime and dust ground into the smooth finish of the bowl and shank. The bowl was heavily caked with lava on the rim top and edges. The inside edge looks like it may actually be undamaged under the lava coat. The rounded outer edge looks very good. The stem was calcified and had tooth chatter and marks on the top and underside near the button and on the button edge. There was no logo or stamping on the stem at all. The pipe showed a lot of promise but it was very dirty. Jeff took some photos of the pipe before he started his cleanup work. He took photos of the rim top and bowl to give a clear picture of the thickness of the cake and tobacco debris as well as the inner edge of the rim. He also took photos of the top and underside of the stem. The photos show the overall condition of the stem. Jeff took photos of the sides of the bowl to give a picture of what the briar looked like. It truly has some nice grain around the bowl and shank.He also took photos to capture the stamping in the metal of the shank. It is clear and readable as noted above.The only information I could find was on the smokingmetal UK website (http://www.smokingmetal.co.uk/pipe.php?page=176). I have included that information below as well as the photos that were there. The flyer I have included also is readable and interesting.

WEAVER, from Weaver Pipes, 1012 Wall Street, El Paso, Texas 79915 USA

Their brochure was copyrighted in 1973 by W R Weaver (originally makers of rifle scopes) so one presumes this was the year of introduction of the pipe

A simple alloy tube, push fit bit and removable plastic end cap. According to the packaging it also came with a cleaning brush which could be used to push out the end cap. The makers call the bit material Valox.

9 bowls available, Classic Billiard (smooth and Barq-relief) Oval shape in Barq-relief with 4 polished panels, Octagon Shape in Barq-relief, Masculine Heavy in Pot shape Barq-relief, Apple shape in Smooth or Barq-relief, Apple in Barq-relief with 4 polished panels and a Littel Buckeye in polished finish

Stamping on left side of pipe Weaver Pipes El Paso Taxas USA pat pend.

Overall length 5 5/8 inch (143 m/m) Jeff had cleaned up the pipe with his usual penchant for thoroughness. He reamed the pipe with a PipNet pipe reamer and removed the rest of it with a Savinelli Fitsall Pipe Knife. He scrubbed the bowl and shank with undiluted Murphy’s Oil Soap with a tooth brush. He rinsed it under running warm water to remove the soap and grime. He cleaned out the inside of the shank and the airway in the stem with alcohol, cotton swabs, shank brushes and pipe cleaners. He soaked the stem in a Briarville’s Pipe Stem Deoxidizer bath and rinsed it off with warm water. I took photos of the pipe before I started my part of the restoration work. It looked very good. The rim top cleaned up really well. The rim top, inner and outer edge of the bowl are in excellent condition. The stem surface looked very good with a few tooth marks and chatter on both sides near the button. There was also some remaining oxidation. The stamping on the shank side is very readable. It is stamped as noted above. I removed the stem and took a photo of the pipe to give a sense of the whole. The taper stem is nice and the photo gives a sense of what the pipe looks like.I used a screwdriver to unscrew the screw holding the briar bowl to the metal tube. I used a large slotted screwdriver to break it free. Once I had the screw out I was able to remove the bowl from the metal shank. You can see the buildup of “crud” on the tube where the bowl had been sitting. It was hard and needed to be scraped off. I took a photo of the parts to show what I was dealing with at this point. I scraped the red build up on the metal shank with sharp blade. I polished the metal with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped the shank down with a damp cloth after each pad. I gave it a final buff with a soft cloth. It really has a nice shine at this point. I fit the end plug in the shank end and pressed it in place. I set the shank aside and turned my attention to the bowl. I sanded the smooth rim and sides of the panel bowl with 320-3500 grit 2 x 2 inch sanding pads. I wiped the bowl down after each sanding pad with a damp cloth to remove the sanding debris. It began to take on a rich shine. I polished the briar with micromesh sanding pads – dry sanding with 1500-12000 grit pads. I wiped the bowl down after each pad with a damp cloth to remove the sanding dust. By the end of the process the pipe bowl looked very good. I worked some Before & After Restoration Balm into the surface of the briar with a shoe brush to get into the rustication on the four corners of the panel bowl and the heel and my fingertips on the smooth. The product works to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I pulled together the polished shank and cleaned screw as well as the briar bowl. It looked significantly better and was ready to put those parts together. I put the parts together and tightened the screw in the bowl and into the threads on the tubular metal shank. It really is an interesting looking pipe. I set the bowl aside and turned my attention to the vulcanite stem. I sanded the stem with 320-3500 grit sanding pads to remove the tooth marks and chatter against the button edge. I wiped the stem down between pads with an Obsidian Oil cloth to remove the sanding debris from the stem.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. This smooth, nicely grained Briar Bowl Metal Base Weaver © El Paso Texas USA Pat Pend Billiard is a great looking pipe now that it has been restored. The rich finish and rusticated corners give the shape an elegant look. The flow of the bowl and stem are well done make for a great hand feel. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the metal and normal touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the entire pipe with a clean buffing pad. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Weaver Metal Pipe with a Briar Bowl fits nicely in the hand and feels great. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 5 ¾ inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 39 grams/1.41 ounces. It is a great looking and light weight pipe. I will be putting it on the rebornpipes store in the Pipes by Various Makers Section shortly. If you are interested in adding this pipe to your collection send me a message or an email. Thanks for reading this blog and my reflections on the pipe while I worked on it.