by Steve Laug

The next pipe I have chosen is a smooth Peterson’s Billiard. It was also incredibly dirty. It came to us from our contact in Copenhagen, Denmark on 04/11/2023. The grime was ground into the finish on the bowl sides. The contrast of the brown stains gave the grain a sense of depth. It was stamped on the left side of the shank and read Peterson’s [over] “Aran”. The right side had the had three lines reading Made in the Republic of Ireland [followed by] the shape number 6 stamped next to the bowl shank junction. There was a thick cake in the bowl and an overflow of lava on the rim top and inner edge. There was some darkening on the outer edge of the bowl. The stem was oxidized, calcified and had light tooth marks, chatter and scratches on the top and underside on and near the button. Jeff took photos of the pipe before his cleanup work. They tell the story and give a glimpse of the promise that we see in this pipe. Jeff took photos of the rim top and stem to show the general condition of the pipe. The bowl is heavily caked and the rim top and edges have a thick lava overflow. The photos of the stem show that it was oxidized and has light tooth marks on the top and underside near the button. Jeff took photos of the bowl sides and heel to show the grain that was around this bowl. It is a nice looking pipe. He took photos of the stamping on the sides of the shank. It is clear and readable and reads as noted above. I turned to “The Peterson Pipe” by Mark Irwin and Gary Malmberg to get some background on the Aran line. On page 294 it had the following information.

Aran (1965-) First issue of line described as “handhewn” (rusticated) with black semi-matte finish, in P-lip and fishtail mouthpiece. Second issue 1975, red sandblast, XL shapes. Third issue circa ’97, gold hot-foil P stamped on the mouthpiece, brown semi-matte smooth finish, no band. Fourth issue after 2010, with nickel band, no P stamped on the mouthpiece. Mounted and unmounted versions are available concurrently.

I knew that I was dealing with an Aran from the Third Issue of the Aran line that came out around 1997. It did not have a band and had a semi-matte smooth finish. It came with a fishtail vulcanite stem. Now it was time to work on the pipe.

Jeff had done a great job cleaning up the pipe as usual. He reamed the pipe with a PipNet reamer and cut back the cake back to the bare briar. He cleaned up the walls with a Savinelli Fitsall Pipe Knife. He scrubbed the interior of the bowl and shank with pipe cleaners, shank brushes, cotton swabs and alcohol to remove the tars and oils. He scrubbed the exterior of the pipe with undiluted Murphy’s Oil Soap and a tooth brush to remove the grime from the finish. He worked on the rim top lava and darkening with the soap and tooth brush. He scrubbed the inside of the stem with alcohol and shank brushes, pipe cleaners. He scrubbed the exterior with Soft Scrub and then soaked it in Briarville’s Pipe Stem Deoxidizer. He washed it off with warm water to remove the Deoxidizer. The pipe looked far better when it arrived. I took some close-up photos of the rim top and also of the stem surface. I wanted to show how well it had cleaned up. The rim top photo looks good. There is some darkening on the briar and some nicks in the surface. I also took close up photos of the stem to show the light tooth marks and scratching on the surface near the button. I took photos of the stamping on the left and right side of the shank. You can see that it is stamped as noted above. It is clear and readable. There is also a faint P logo on the left side of the stem. I took the pipe apart and took a photo of the pipe. It is a good-looking pipe and has some great grain on the sides of the bowl.I cleaned up the top and inner edge with a folded piece of 220 grit sandpaper. I was able to remove the darkening and light scratches on the surface and edges.I sanded the bowl with 320-3500 grit 2×2 inch sanding pads. I wiped the briar down with a damp cloth to remove the sanding debris. By the final pad it was looking much better. I polished the briar bowl and shank with micromesh sanding pads. I dry sanded it with 1500-12000 grit pads and wiped it down with a damp cloth after each pad. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I decided to see what the pipe would look like with a thin brass band. It is not required but I wondered if it would give a sense of bling to the pipe. Several of the previous Aran pipes I have worked on had bands so I wondered. I fit it on the shank end and looked at what the pipe looked like with it. After seeing it I made the decision to glue the band and press it onto the shank. I took photos of the bowl and shank with the new look. I really like the looks of it. I set the bowl aside and turned my attention to the stem. I “painted” the surface of the stem with the flame of a lighter to lift the tooth marks as much as possible. I filled in the remaining marks with rubberized black CA glue and let it cure. Once it cured I smoothed out the repairs and recut the button edge with small files. I sanded out the remaining marks and repairs with 220 grit sandpaper. I wiped the stem down with Obsidian Oil before continuing. It was looking better. I sanded the stem with 320-3500 grit 2×2 inch pads to further smooth out the surface and remove the light residual oxidation. I wiped the stem down after each pad with an Obsidian Oil cloth to remove the debris and further protect the stem.I polished the stem with micromesh sanding pads – wet sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I gave the stem a final coat of Obsidian Oil. I am excited to finish this Peterson’s Aran 6 Billiard with a fishtail stem. I put the pipe back together and buffed it with Blue Diamond on the buffing wheel. I gave the bowl and stem multiple coats of carnauba wax. I hand buffed the pipe with a clean buffing pad to raise the shine and hand buffed it with a microfibre cloth to deepen the shine. It is fun to see what the polished bowl looks like with the polished thin brass band and the black vulcanite stem. This Classic looking Peterson’s Aran 6 Billiard feels great in my hand. It is light and well balanced. Have a look at it with the photos below. The dimensions are Length: 6 inches, Height: 1 ¾ inches, Outside diameter of the bowl: 1 ¼ inches, Chamber diameter: ¾ of an inch. The weight of the pipe is 38 grams/1.34 ounces. It is a beautiful pipe and one that will be on the Irish Pipe Makers section of the rebornpipes store soon. If you are interested in adding it to your collection let me know. Thanks for walking through the restoration with me as I worked over this pipe. Thanks to each of you who are reading this blog.