by Steve Laug

It may seem I have endless choices of pipes to work on. While we do have a lot of pipes that are in the queue to be restored it is far from endless. This next pipe I chose to work on was one that we purchased a few years ago on 05/10/2022 from an antique shop in Astoria, Oregon, USA. The pipe is stamped on the left side of the shank and reads Thayne [over] Made in Denmark. This one is a unique beauty with a smooth rim top and cap down the first third of the bowl. There was a smooth band around the shank end and a smooth patch on the left side of the shank for the stamping. The rest of the shank and 2/3 of the bowl from the smooth section to the heel of the bowl has a deep, rugged well grained sandblast. The stem is a fancy saddle stem with a T logo on the left side of the saddle stem. The exterior of the pipe was covered with dust and debris in the blast. There was a thick cake in the bowl and some lava and darkening on the rim top flowing down the outside curve of the rim. The vulcanite stem is a fancy turned saddle stem that is comfortable. It was oxidized, calcified and had tooth marks and chatter on both sides ahead of the button. Jeff took photos of the pipe before he started his clean up work. Jeff took photos of the rim top and stem to show the general condition of the pipe. The bowl is heavily caked and there was lava on the rim top and down the edges. The stem was oxidized, calcified and had some tooth marks and chatter. It should cleanup very well. Jeff took photos of the bowl sides and heel to show the smooth bowl cap and the beautiful blast that was around this bowl even though the grime on the finish hides it some. The pipe had obviously been well loved and cared for by the previous pipeman. He took photos of the sides of the shank to show the stamping. The stamping is clear and readable in the photos below as noted above. This is a new brand for me to work on. It is a Thayne pipe which is a brand I have not worked on before. It is similar in style and shape and stamping to a Jarl, I turned to Pipephil’s site to get an overview of the brand (http://www.pipephil.eu/logos/en/logo-t4.html). I did a screen capture of the site’s information and have included that below.I turned then to Pipedia to see if there was more information (https://pipedia.org/wiki/Thayne)

Thayne pipes are apparently made by the same maker as made Jarl pipes, who was reportedly Niels Mogens Jørgensen.

What I learned from the research is that the pipe is a pipe possibly made by the same carver that does the Jarl pipes. It is likely made by Niels Mogens Jorgensen. It is a beautiful pipe in both shape and finish.

Jeff did a great job cleaning up the pipe. He reamed the bowl with a PipNet pipe reamer and cleaned up the cake with a Savinelli Fitsall Pipe Knife. He scrubbed out the mortise and the airway in the shank and the stem with alcohol, shanks brushes, cotton swabs and pipe cleaners. He scrubbed the exterior of the bowl, rim and shank with a tooth brush and Murphy’s Oil Soap to the oils and tars on the bowl, rim and shank. He removed the light lava coat on the top of the rim. He rinsed the bowl under running water. He dried it off with a soft cloth. Once the grime was removed the finish underneath was in good condition. The stain and the look of the finish was very well done. He scrubbed the exterior of the stem with Soft Scrub and rinsed it with warm water. He wiped the bowl and stem down with a light coat of olive oil and buffed it with a soft cloth. The pipe really was quite stunning. I took photos of the pipe to show its condition before I started my work on it. I took a close up photo of the rim top and edges to show how well it had cleaned up and the edges around the bowl. There was some darkening around the back top and inner edge of the bowl. I also took close up photos of the stem to show the light tooth chatter on the surface ahead of the button on both sides.I took a photo of the stamping on the sides of the shank. It is clear and readable as noted above. I removed the stem and took a photo of the pipe to show the proportions of the pipe. It is a beauty.I polished the briar on the rim cap and the smooth shank end with micromesh sanding pads – 1500-12000 grit pads. I wiped the briar down with a damp cloth after each pad. It really looked very good. I worked some Before & After Restoration Balm into the surface of the briar with my fingertips and a shoe brush to clean, enliven and protect the briar. I let the balm sit for 15 minutes and then buffed with a cotton cloth to raise the shine. The photos show the bowl at this point in the restoration process. I set the bowl aside and turned my attention to the stem. I filled in the tooth marks on both sides of the stem with clear CA glue. I set it aside to cure. Once it cured, I flattened the repaired areas with needle files. I further smoothed them out with 220 grit sandpaper to blend them into the surface. I touched up the T logo stamp with white acrylic fingernail polish. Once it cured I scraped off the excess. I sanded it carefully with 220 grit sandpaper. The logo looked much better and was very legible.I sanded the stem with 320-3500 grit sanding pads and wiped the stem down with Obsidian Oil after each sanding pad. The stem began to take on a shine.I polished the stem with micromesh sanding pads – dry sanding with 1500-12000 grit sanding pads. I wiped it down after each sanding pad with Obsidian Oil. I polished it with Before & After Pipe Stem Polish – both Fine and Extra Fine. I gave it another coat of Obsidian Oil. I am really happy with the way that this Thayne Danish Made 123B Mix Finish Acorn turned out. It really is a beautiful looking pipe with a unique shape and combination of a smooth rim cap and shank end with a rich and rugged sandblast finish. The fancy vulcanite saddle stem is really nice. The briar really came alive with the buffing. The rich brown and black stains of the finish gave the pipe a sense of depth with the polishing and waxing. I put the stem back on the bowl and carefully buffed the pipe with Blue Diamond on the buffing wheel using a light touch on the briar. I gave the bowl and the stem multiple coats of carnauba wax on the buffing wheel. I buffed the pipe with a clean buffing pad to raise the shine. I hand buffed the pipe with a microfiber cloth to deepen the shine. The finished Thayne Danish Made 123B Acorn really is a beauty and feels great in the hand and looks very good. Give the finished pipe a look in the photos below. The dimensions of the pipe are Length: 6 inches, Height: 2 inches, Outside diameter of the bowl: 1 ½ inch, Chamber diameter: ¾ of an inch. The weight of the pipe is 41 grams/1.48 ounces. The pipe will be going on the rebornpipes store in the Danish Pipe Makers Section if you would like to add it to your collection. Thanks for reading this blog and my reflections on the pipe while I worked on it. It was a fun one to work on!